[5074]beign to init dram
[5076]DRAM DRIVE INFO: V0.9
[5079]DRAM Type = 2 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
[5084]DRAM CLK = 456 MHz
[5087]DRAM zq value: 000039bb
[5112]DRAM size = 64 MB
[5120]init dram ok


U-Boot 2014.07 (Feb 24 2020 - 10:54:27) Allwinner Technology 

uboot commit : fe4e5a2b4205c27be53bc7aa7ed0396a9774aa21
 
normal mode
i2c_init: by cpux
i2c_init ok
[8.763]pmbus:   ready
axp read error
probe axp failed
axp_probe error
[8.873]PMU: pll1 912 Mhz,PLL6=600 Mhz
AXI=304 Mhz,AHB=200 Mhz, APB1=100 Mhz 
DRAM:  64 MiB
[8.881]fdt addr: 0x424e7020
[8.882]gd->fdt_size: 0xc720
Relocation Offset is: 02efb000
gic: normal mode
[8.927]flash init start
workmode = 16,storage type = 0
try card 1
[8.929][mmc]: mmc driver ver 2019-6-14 17:37:00
[8.933][mmc]: sdc_on error, 1

[8.936][mmc]: MMC Device 1 not found
try card 2
[8.940][mmc]: mmc driver ver 2019-6-14 17:37:00
[8.945][mmc]: get card0 para fail
[8.948][mmc]: mmc_update_timing_para: error sdc_no 2
SUNXI SD/MMC: 2
[8.959][mmc]: ************Try SD card 2************
[mmc]: mmc 2 cmd 8 timeout, err 2
[mmc]: smc 2 err, cmd 8,  RE
[mmc]: mmc 2 close bus gating and reset
[mmc]: mmc 2 mmc cmd 8 err 0x00000002
[8.971][mmc]: mmc send if cond failed
[mmc]: mmc 2 cmd 55 timeout, err 2
[mmc]: smc 2 err, cmd 55,  RE
[mmc]: mmc 2 close bus gating and reset
[mmc]: mmc 2 mmc cmd 55 err 0x00000002
[8.987][mmc]: send app cmd failed
[8.990][mmc]: ************Try MMC card 2************
[mmc]: mmc 2 cmd 1 timeout, err 2
[mmc]: smc 2 err, cmd 1,  RE
[mmc]: mmc 2 close bus gating and reset
[mmc]: mmc 2 mmc cmd 1 err 0x00000002
[9.008][mmc]: read op condition failed
[9.011][mmc]: mmc send op cond failed
Card did not respond to voltage select!
[9.018][mmc]: ************SD/MMC 2 init error!!!************
[9.023][mmc]: mmc_init_boot: mmc int fail
[9.027][mmc]: mmc_init: mmc init fail, err -17
MMC init failed
try emmc fail
NAND_UbootProbe start
NB1 : enter phy init
NandHwInit: Start Nand Hardware initializing .....
uboot:nand version: 2 8 20190408 1958 
Reg 0x01c20848: 0x3333
Reg 0x01c2085c: 0x55
Reg 0x01c20864: 0x10
uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x438b767c
request general tx dma channel ok!
uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x438b7698
request general rx dma channel ok!
SPI nand ID: cd7171cd 71cd7171
_SearchNandArchi fail
[ERR]NandHwInit: SCN_AnalyzeNandSystem() failed!
NandHwInit: End Nand Hardware initializing ..... FAIL!
NB1 : nand phy init fail
NB1 : enter phy Exit
nand release dma:438b767c
nand release dma:0
NAND_UbootProbe end: 0xffffffff
try nand fail
flash size =0x8000 sectors
sunxi spinor is initing...OK
spinor id:0x71cd00
spi_freq = 40000000
spinor id is 71cd00 
try nor successed 
read mbr copy[0] failed
read mbr copy[1] failed
read mbr copy[2] failed
read mbr copy[3] failed
[9.119]flash init end
[9.121]try to burn key
Net:   usb_ether
[9.124]inter uboot shell
Hit any key to stop autoboot:  0 
work mode=0x10
run usb efex
delay time 2500
weak:otg_phy_config
usb init ok
set address 0x12
set address 0x12 ok
set address 0x13
set address 0x13 ok
SUNXI_EFEX_ERASE_TAG
erase_flag = 0x1
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
the 0 mbr table is ok
*************MBR DUMP***************
total mbr part 8

part[0] name      :bootlogo
part[0] classname :DISK
part[0] addrlo    :0x20
part[0] lenlo     :0xd00
part[0] user_type :32768
part[0] keydata   :0
part[0] ro        :0

part[1] name      :env
part[1] classname :DISK
part[1] addrlo    :0xd20
part[1] lenlo     :0x200
part[1] user_type :32768
part[1] keydata   :0
part[1] ro        :0

part[2] name      :boot
part[2] classname :DISK
part[2] addrlo    :0xf20
part[2] lenlo     :0x2000
part[2] user_type :32768
part[2] keydata   :0
part[2] ro        :0

part[3] name      :rootfs
part[3] classname :DISK
part[3] addrlo    :0x2f20
part[3] lenlo     :0x4680
part[3] user_type :32768
part[3] keydata   :0
part[3] ro        :0

part[4] name      :rootfs_data
part[4] classname :DISK
part[4] addrlo    :0x75a0
part[4] lenlo     :0x80
part[4] user_type :32768
part[4] keydata   :0
part[4] ro        :0

part[5] name      :misc
part[5] classname :DISK
part[5] addrlo    :0x7620
part[5] lenlo     :0x80
part[5] user_type :32768
part[5] keydata   :0
part[5] ro        :0

part[6] name      :private
part[6] classname :DISK
part[6] addrlo    :0x76a0
part[6] lenlo     :0x80
part[6] user_type :32768
part[6] keydata   :0
part[6] ro        :0

part[7] name      :UDISK
part[7] classname :DISK
part[7] addrlo    :0x7720
part[7] lenlo     :0x0
part[7] user_type :33024
part[7] keydata   :0
part[7] ro        :0

total part: 9
mbr 0, 20, 8000
bootlogo 1, d00, 8000
env 2, 200, 8000
boot 3, 2000, 8000
rootfs 4, 4680, 8000
rootfs_data 5, 80, 8000
misc 6, 80, 8000
private 7, 80, 8000
UDISK 8, 0, 8100
do need erase flash
sunxi_sprite_erase_flash, erase_flag=1
private part exist
flash size =0x8000 sectors
sunxi spinor is already inited
spinor read: start 0x3e0, sector 0x20
the 0 mbr table is bad
the mbr on flash is bad
force sunxi spinor exit
begin to erase all ..
status = 0
count = 1 
SUNXI_EFEX_MBR_TAG
mbr size = 0x4000
flash size =0x8000 sectors
sunxi spinor is initing...OK
spinor id:0x71cd00
spi_freq = 40000000
start = 0x380, cnt=0x80
sunxi_sprite_verify_mbr_from_flash
spinor read: start 0x3e0, sector 0x20
the 0 mbr table is bad
mbr_verify fail
sunxi_sprite_verify_mbr_from_flash fail
sunxi spinor is exiting