[889]fes begin commit:3fee797 [892]set pll start [894]periph0 has been enabled [897]set pll end [898]board init ok [900]beign to init dram [903]the chip id is 0x3 [905]the chip id is 0x3 [907]the chip id is 0x3 [909]the chip id is 0x3 [912]the chip id is 0x3 [914]chip id check OK [917][AUTO DEBUG] two rank and full DQ! [920][AUTO DEBUG] DDR3 try success [924][AUTO DEBUG] single rank and full DQ! [929][AUTO DEBUG] rank 0 row = 14 [932][AUTO DEBUG] rank 0 bank = 8 [935][AUTO DEBUG] rank 0 page size = 2 KB [939]DRAM BOOT DRIVE INFO: V0.20 [942]DRAM Type = 3 (2:DDR2,3:DDR3) [946]DRAMC read ODT off. [948]DRAM ODT off. [951]DRAM CLK = 774 MHz [953]DRAM SIZE =256 M [956]DRAM simple test OK. [959]init dram ok U-Boot 2018.05-g6f0ec64 (Apr 27 2022 - 02:21:36 +0000) Allwinner Technology [03.167]CPU: Allwinner Family [03.170]Model: sun50iw11 I2C: ready [03.295]DRAM: 256 MiB [03.297]Relocation Offset is: 0cefa000 [03.321]secure enable bit: 0 [03.325]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=0Mhz [03.331]gic: normal mode [03.333]flash init start [03.335]workmode = 16,storage type = 0 try card 0 set card number 0 get card number 0 [03.343][mmc]: mmc driver ver uboot2018:2021-09-07 19:43:00 [03.356][mmc]: Is not Boot mode! [03.358][mmc]: SUNXI SDMMC Controller Version:0x50320 [03.370][mmc]: ************Try SD card 0************ [03.375][mmc]: mmc 0 cmd timeout 100 status 100 [03.379][mmc]: smc 0 err, cmd 8, RTO [03.382][mmc]: mmc 0 close bus gating and reset [03.387][mmc]: mmc 0 cmd timeout 100 status 100 [03.391][mmc]: smc 0 err, cmd 55, RTO [03.395][mmc]: mmc 0 close bus gating and reset [03.399][mmc]: ************Try MMC card 0************ [03.408][mmc]: mmc 0 cmd timeout 100 status 100 [03.412][mmc]: smc 0 err, cmd 1, RTO [03.416][mmc]: mmc 0 close bus gating and reset [03.420][mmc]: Card did not respond to voltage select! [03.425][mmc]: ************SD/MMC 0 init error!************ [03.430][mmc]: mmc init product failed MMC init failed try emmc fail [03.438]sunxi-spinand: AW SPINand MTD Layer Version: 1.5 20200407 [03.443]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.9 20200306 [03.455]sunxi-spinand-phy: request spi0 gpio ok [03.459]sunxi-spinand-phy: request general tx dma channel ok! [03.464]sunxi-spinand-phy: request general rx dma channel ok! [03.470]sunxi-spinand-phy: set spic0 clk to 20 Mhz [03.474]sunxi-spinand-phy: init spic0 clk ok sspi->base_addr = 0x4025000, the SPI control register: [VER] 0x4025000 = 0x00010001, [GCR] 0x4025004 = 0x00000083, [TCR] 0x4025008 = 0x00000184 [ICR] 0x4025010 = 0x00000f00, [ISR] 0x4025014 = 0x00000032, [FCR] 0x4025018 = 0x00200020 [FSR] 0x402501c = 0x00000000, [WCR] 0x4025020 = 0x00000000, [CCR] 0x4025024 = 0x00000002 [SDC] 0x4025028 = 0x00002000, [BCR] 0x4025030 = 0x00000000, [TCR] 0x4025034 = 0x00000000 [BCC] 0x4025038 = 0x00000000, [DMA] 0x4025088 = 0x000000e5 [03.520]sunxi-spinand-phy: not detect any munufacture from id table [03.527]sunxi-spinand-phy: get spi-nand Model from fdt fail [03.532]sunxi-spinand-phy: get phy info from fdt fail [03.537]sunxi-spinand-phy: not detect munufacture from fdt [03.542]sunxi-spinand-phy: detect munufacture from id table: GD [03.548]sunxi-spinand-phy: detect spinand id: ffff52c8 ffffffff [03.553]sunxi-spinand-phy: ========== arch info ========== [03.559]sunxi-spinand-phy: Model: GD5F2GQ5UEYIGR [03.564]sunxi-spinand-phy: Munufacture: GD [03.569]sunxi-spinand-phy: DieCntPerChip: 1 [03.573]sunxi-spinand-phy: BlkCntPerDie: 2048 [03.578]sunxi-spinand-phy: PageCntPerBlk: 64 [03.582]sunxi-spinand-phy: SectCntPerPage: 4 [03.587]sunxi-spinand-phy: OobSizePerPage: 64 [03.591]sunxi-spinand-phy: BadBlockFlag: 0x0 [03.596]sunxi-spinand-phy: OperationOpt: 0x7 [03.600]sunxi-spinand-phy: MaxEraseTimes: 50000 [03.605]sunxi-spinand-phy: EccFlag: 0x1 [03.610]sunxi-spinand-phy: EccType: 7 [03.614]sunxi-spinand-phy: EccProtectedType: 2 [03.619]sunxi-spinand-phy: ======================================== [03.625]sunxi-spinand-phy: [03.627]sunxi-spinand-phy: ========== physical info ========== [03.633]sunxi-spinand-phy: TotalSize: 256 M [03.637]sunxi-spinand-phy: SectorSize: 512 B [03.641]sunxi-spinand-phy: PageSize: 2 K [03.645]sunxi-spinand-phy: BlockSize: 128 K [03.649]sunxi-spinand-phy: OOBSize: 64 B [03.653]sunxi-spinand-phy: ======================================== [03.659]sunxi-spinand-phy: [03.662]sunxi-spinand-phy: ========== logical info ========== [03.667]sunxi-spinand-phy: TotalSize: 256 M [03.671]sunxi-spinand-phy: SectorSize: 512 B [03.675]sunxi-spinand-phy: PageSize: 4 K [03.679]sunxi-spinand-phy: BlockSize: 256 K [03.684]sunxi-spinand-phy: OOBSize: 128 B [03.688]sunxi-spinand-phy: ======================================== [03.695]sunxi-spinand-phy: set spic0 clk to 100 Mhz [03.700]sunxi-spinand-phy: block lock register: 0x00 [03.704]sunxi-spinand-phy: feature register: 0x11 [03.709]sunxi-spinand-phy: sunxi physic nand init end [03.714]Loading Environment from SUNXI_FLASH... OK [03.719]try to burn key [03.722]out of usb burn from boot: not boot mode Hit any key to stop autoboot: 0 sunxi work mode=0x10 run usb efex delay time 2500 weak:otg_phy_config usb init ok set address 0x2f set address 0x2f ok set address 0x30 set address 0x30 ok SUNXI_EFEX_ERASE_TAG erase_flag = 0x0 origin_erase_flag = 0x0 FEX_CMD_fes_verify_status FEX_CMD_fes_verify last err=0 the 0 mbr table is ok the 1 mbr table is ok the 2 mbr table is ok the 3 mbr table is ok *************MBR DUMP*************** total mbr part 7 part[0] name :boot-resource part[0] classname :DISK part[0] addrlo :0x1f8 part[0] lenlo :0x3f0 part[0] user_type :32768 part[0] keydata :0 part[0] ro :0 part[1] name :env part[1] classname :DISK part[1] addrlo :0x5e8 part[1] lenlo :0x1f8 part[1] user_type :32768 part[1] keydata :0 part[1] ro :0 part[2] name :env-redund part[2] classname :DISK part[2] addrlo :0x7e0 part[2] lenlo :0x1f8 part[2] user_type :32768 part[2] keydata :0 part[2] ro :0 part[3] name :boot part[3] classname :DISK part[3] addrlo :0x9d8 part[3] lenlo :0x2760 part[3] user_type :32768 part[3] keydata :0 part[3] ro :0 part[4] name :rootfs part[4] classname :DISK part[4] addrlo :0x3138 part[4] lenlo :0xf12c part[4] user_type :32768 part[4] keydata :0 part[4] ro :0 part[5] name :recovery part[5] classname :DISK part[5] addrlo :0x12264 part[5] lenlo :0x6e40 part[5] user_type :32768 part[5] keydata :0 part[5] ro :0 part[6] name :UDISK part[6] classname :DISK part[6] addrlo :0x190a4 part[6] lenlo :0x0 part[6] user_type :33024 part[6] keydata :0 part[6] ro :0 total part: 8 mbr 0, 1f8, 8000 boot-resource 1, 3f0, 8000 env 2, 1f8, 8000 env-redund 3, 1f8, 8000 boot 4, 2760, 8000 rootfs 5, f12c, 8000 recovery 6, 6e40, 8000 UDISK 7, 0, 8100 [06.913]erase blk 0 to blk 32 need erase flash: 0 [06.977]mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,512k@5242880(pstore)ro,-(sys) device nand0 , # parts = 5 #: name size offset mask_flags 0: boot0 0x00100000 0x00000000 1 1: uboot 0x00300000 0x00100000 1 2: secure_storage 0x00100000 0x00400000 1 3: pstore 0x00080000 0x00500000 1 4: sys 0x0fa80000 0x00580000 0 active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000 defaults: mtdids : nand0=nand mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,512k@5242880(pstore)ro,-(sys) [07.035]MTD info (5) [07.037]pagesize: 0x1000 [07.039]blksize: 0x40000 [07.042]num offset bytes name [07.045]0 0x00000000 0x00100000 boot0 [07.049]1 0x00100000 0x00300000 uboot [07.053]2 0x00400000 0x00100000 secure_storage [07.057]3 0x00500000 0x00080000 pstore [07.061]4 0x00580000 0x0fa80000 sys [07.064]ubi attach the last part of mtd device: NO.4 [07.202]ubi0: attaching mtd5 [07.399]ubi0: scanning is finished [07.406]ubi0: attached mtd5 (name "sys", size 250 MiB) [07.410]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes [07.417]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048 [07.423]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [07.429]ubi0: good PEBs: 1002, bad PEBs: 0, corrupted PEBs: 0 [07.434]ubi0: user volume: 8, internal volumes: 1, max. volumes count: 128 [07.441]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0 [07.449]ubi0: available PEBs: 0, total reserved PEBs: 1002, PEBs reserved for bad PEB handling: 40 no part need to protect user data [07.460]erase blk 0 to blk 32 SUNXI_EFEX_MBR_TAG mbr size = 0x10000 force mbr device nand0 , # parts = 5 #: name size offset mask_flags 0: boot0 0x00100000 0x00000000 1 1: uboot 0x00300000 0x00100000 1 2: secure_storage 0x00100000 0x00400000 1 3: pstore 0x00080000 0x00500000 1 4: sys 0x0fa80000 0x00580000 0 active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000 defaults: mtdids : nand0=nand mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,512k@5242880(pstore)ro,-(sys) [07.571]MTD info (5) [07.573]pagesize: 0x1000 [07.575]blksize: 0x40000 [07.578]num offset bytes name [07.581]0 0x00000000 0x00100000 boot0 [07.585]1 0x00100000 0x00300000 uboot [07.588]2 0x00400000 0x00100000 secure_storage [07.593]3 0x00500000 0x00080000 pstore [07.597]4 0x00580000 0x0fa80000 sys [07.600]MBR info (unalign): [07.603]partno addr sects type name [07.607]0 0x00000000 0x000001f8 0x00000001 mbr [07.612]1 0x000001f8 0x000003f0 0x00008000 boot-resource [07.618]2 0x000005e8 0x000001f8 0x00008000 env [07.623]3 0x000007e0 0x000001f8 0x00008000 env-redund [07.628]4 0x000009d8 0x00002760 0x00008000 boot [07.633]5 0x00003138 0x0000f12c 0x00008000 rootfs [07.638]6 0x00012264 0x00006e40 0x00008000 recovery [07.643]7 0x000190a4 0x00000000 0x00008100 UDISK [07.648]ubi attach the last part of mtd device: NO.4 [07.653]MBR info (align): [07.655]partno addr sects type name [07.660]0 0x00002c00 0x000001f8 0x00000001 mbr [07.665]1 0x00002df8 0x000003f0 0x00008000 boot-resource [07.670]2 0x000031e8 0x000001f8 0x00008000 env [07.675]3 0x000033e0 0x000001f8 0x00008000 env-redund [07.680]4 0x000035d8 0x00002760 0x00008000 boot [07.685]5 0x00005d38 0x0000f228 0x00008000 rootfs [07.690]6 0x00014f60 0x00006e40 0x00008000 recovery [07.695]7 0x0001bda0 0x00000000 0x00008100 UDISK [07.700]ubi attach the last part of mtd device: NO.4 [07.705]ubi attatch mtd, name: sys [07.708]ubi0: detaching mtd5 [07.711]ubi0: mtd5 is detached [07.714]ubi0: attaching mtd5 [07.910]ubi0: scanning is finished [07.916]ubi0: attached mtd5 (name "sys", size 250 MiB) [07.921]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes [07.927]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048 [07.933]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [07.940]ubi0: good PEBs: 1002, bad PEBs: 0, corrupted PEBs: 0 [07.945]ubi0: user volume: 8, internal volumes: 1, max. volumes count: 128 [07.952]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0 [07.960]ubi0: available PEBs: 0, total reserved PEBs: 1002, PEBs reserved for bad PEB handling: 40 [07.968]volume mbr existed, not create again [07.972]volume boot-resource existed, not create again [07.977]volume env existed, not create again [07.981]volume env-redund existed, not create again [07.986]volume boot existed, not create again [07.990]volume rootfs existed, not create again [07.994]volume recovery existed, not create again [07.998]volume UDISK existed, not create again [08.026]fill gap start: volume mbr sects 0x178 [08.121]fill gap end: volume mbr [08.124]update partition map [08.126]logical area info: 958 258048 last_lba: 482831 [08.135]logical area info: 958 258048 last_lba: 482831 [08.142]logical area info: 958 258048 last_lba: 482831 [08.150]logical area info: 958 258048 last_lba: 482831 [08.158]logical area info: 958 258048 last_lba: 482831 [08.166]logical area info: 958 258048 last_lba: 482831 [08.174]logical area info: 958 258048 last_lba: 482831 [08.182]logical area info: 958 258048 last_lba: 482831 [08.190]logical area info: 958 258048 last_lba: 482831 [08.198]logical area info: 958 258048 last_lba: 482831 [08.206]logical area info: 958 258048 last_lba: 482831 [08.214]logical area info: 958 258048 last_lba: 482831 [08.222]logical area info: 958 258048 last_lba: 482831 [08.230]logical area info: 958 258048 last_lba: 482831 [08.237]logical area info: 958 258048 last_lba: 482831 [08.245]logical area info: 958 258048 last_lba: 482831 [08.253]logical area info: 958 258048 last_lba: 482831 [08.261]logical area info: 958 258048 last_lba: 482831 [08.269]logical area info: 958 258048 last_lba: 482831 [08.277]logical area info: 958 258048 last_lba: 482831 [08.285]logical area info: 958 258048 last_lba: 482831 [08.293]logical area info: 958 258048 last_lba: 482831 [08.301]logical area info: 958 258048 last_lba: 482831 [08.309]logical area info: 958 258048 last_lba: 482831 [08.316]logical area info: 958 258048 last_lba: 482831 FEX_CMD_fes_verify_status FEX_CMD_fes_verify last err=0 [08.422]fill gap start: volume boot-resource sects 0x142 [08.502]fill gap end: volume boot-resource FEX_CMD_fes_verify_value, start 0x1f8, size high 0x0:low 0x55c00 FEX_CMD_fes_verify_value 0x22eca6c0 [08.561]fill gap start: volume env sects 0xf8 [08.640]fill gap end: volume env FEX_CMD_fes_verify_value, start 0x5e8, size high 0x0:low 0x20000 FEX_CMD_fes_verify_value 0xccf6ae0d [08.688]fill gap start: volume env-redund sects 0xf8 [08.768]fill gap end: volume env-redund FEX_CMD_fes_verify_value, start 0x7e0, size high 0x0:low 0x20000 FEX_CMD_fes_verify_value 0xccf6ae0d [09.821]fill gap start: volume boot sects 0x8b8 [09.907]fill gap end: volume boot FEX_CMD_fes_verify_value, start 0x9d8, size high 0x0:low 0x3d5000 FEX_CMD_fes_verify_value 0x2f586ee5 [15.453]fill gap start: volume rootfs sects 0x552c [15.592]fill gap end: volume rootfs FEX_CMD_fes_verify_value, start 0x3138, size high 0x0:low 0x1380000 FEX_CMD_fes_verify_value 0x91198b72 bootfile_mode=4 SUNXI_EFEX_BOOT1_TAG boot1 size = 0xdc000, max size = 0x200000 uboot size = 0xdc000 storage type = 0 [16.632]uboot blk range [8-32) [16.635]download uboot to block 8 (7 blocks) len 880K [16.845]download uboot to block 15 (7 blocks) len 880K [17.055]download uboot to block 22 (7 blocks) len 880K FEX_CMD_fes_verify_status FEX_CMD_fes_verify last err=0 bootfile_mode=4 SUNXI_EFEX_BOOT0_TAG boot0 size = 0xc000 dram para[0] = 0 dram para[1] = 3 dram para[2] = bfb dram para[3] = 0 dram para[4] = 10d2 dram para[5] = 0 dram para[6] = 1c70 dram para[7] = 2 dram para[8] = 18 dram para[9] = 0 dram para[10] = 4a2195 dram para[11] = 2423190 dram para[12] = 8b061 dram para[13] = b4787896 dram para[14] = 0 dram para[15] = 48484848 dram para[16] = 30000048 dram para[17] = 1620121e dram para[18] = 0 dram para[19] = 0 dram para[20] = 0 dram para[21] = 220000 dram para[22] = 55 dram para[23] = 14000100 dram para[24] = 0 dram para[25] = 0 dram para[26] = 0 dram para[27] = 0 dram para[28] = 0 dram para[29] = 0 dram para[30] = 0 dram para[31] = 0 storage type = 0 [17.337]download boot0 to block 0 len 48K [17.354]download boot0 to block 1 len 48K [17.370]download boot0 to block 2 len 48K [17.386]download boot0 to block 3 len 48K [17.401]download boot0 to block 4 len 48K [17.417]download boot0 to block 5 len 48K [17.433]download boot0 to block 6 len 48K [17.450]download boot0 to block 7 len 48K FEX_CMD_fes_verify_status FEX_CMD_fes_verify last err=0 sunxi_efex_next_action=2 exit usb next work 2 SUNXI_UPDATE_NEXT_ACTION_REBOOT [49]HELLO! BOOT0 is starting! [52]BOOT0 commit : 3fee797 [55]set pll start [57]periph0 has been enabled [60]set pll end [62]board init ok [64]enable_jtag [65]key press : [67]the chip id is 0x3 [69]the chip id is 0x3 [72]the chip id is 0x3 [74]the chip id is 0x3 [76]the chip id is 0x3 [79]chip id check OK [82][AUTO DEBUG] two rank and full DQ! [85][AUTO DEBUG] DDR3 try success [89][AUTO DEBUG] single rank and full DQ! [94][AUTO DEBUG] rank 0 row = 14 [98][AUTO DEBUG] rank 0 bank = 8 [101][AUTO DEBUG] rank 0 page size = 2 KB [105]DRAM BOOT DRIVE INFO: V0.20 [108]DRAM Type = 3 (2:DDR2,3:DDR3) [112]DRAMC read ODT off. [114]DRAM ODT off. [117]DRAM CLK = 774 MHz [119]DRAM SIZE =256 M [125]DRAM simple test OK. [128]dram size =256 [130]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32 [136]block from 8 to 32 [236]Check is correct. [238]dma 0x10818c int is not used yet [242]dma 0x10818c int is free, you do not need to free it again [248]Entry_name = u-boot [255]Entry_name = monitor [258]Entry_name = dtb [261]Jump to second Boot. NOTICE: BL3-1: v1.0(debug):6efeeb8 NOTICE: BL3-1: Built : 13:54:32, 2022-04-24 NOTICE: BL3-1 commit: 8 ERROR: Error initializing runtime service tspd_fast NOTICE: BL3-1: Preparing for EL3 exit to normal world NOTICE: BL3-1: Next image address = 0x43000000 ▒OTICE: BL3-1: Next image spsr = 0x1d3 U-Boot 2018.05-g6f0ec64 (Apr 27 2022 - 02:21:36 +0000) Allwinner Technology [00.318]CPU: Allwinner Family [00.321]Model: sun50iw11 I2C: ready [00.445]DRAM: 256 MiB [00.448]Relocation Offset is: 0cefa000 [00.471]secure enable bit: 0 [00.474]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=0Mhz [00.480]gic: sec monitor mode [00.483]flash init start [00.485]workmode = 0,storage type = 0 sspi->base_addr = 0x4025000, the SPI control register: [VER] 0x4025000 = 0x00010001, [GCR] 0x4025004 = 0x00000083, [TCR] 0x4025008 = 0x00000184 [ICR] 0x4025010 = 0x00000f00, [ISR] 0x4025014 = 0x00000032, [FCR] 0x4025018 = 0x00200020 [FSR] 0x402501c = 0x00000000, [WCR] 0x4025020 = 0x00000000, [CCR] 0x4025024 = 0x00000002 [SDC] 0x4025028 = 0x00002000, [BCR] 0x4025030 = 0x00000000, [TCR] 0x4025034 = 0x00000000 [BCC] 0x4025038 = 0x10000000, [DMA] 0x4025088 = 0x000000e5 [00.537]sunxi-spinand-phy: not detect any munufacture from id table [00.544]sunxi-spinand-phy: get spi-nand Model from fdt fail [00.549]sunxi-spinand-phy: get phy info from fdt fail device nand0 , # parts = 5 #: name size offset mask_flags 0: boot0 0x00100000 0x00000000 1 1: uboot 0x00300000 0x00100000 1 2: secure_storage 0x00100000 0x00400000 1 3: pstore 0x00080000 0x00500000 1 4: sys 0x0fa80000 0x00580000 0 active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000 defaults: mtdids : nand0=nand mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,512k@5242880(pstore)ro,-(sys) [00.738]ubi0: attaching mtd5 [00.934]ubi0: scanning is finished [00.940]ubi0: attached mtd5 (name "sys", size 250 MiB) [00.945]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes [00.951]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048 [00.957]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [00.964]ubi0: good PEBs: 1002, bad PEBs: 0, corrupted PEBs: 0 [00.969]ubi0: user volume: 8, internal volumes: 1, max. volumes count: 128 [00.976]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0 [00.983]ubi0: available PEBs: 0, total reserved PEBs: 1002, PEBs reserved for bad PEB handling: 40 [00.992]sunxi flash init ok [01.076]Loading Environment from SUNXI_FLASH... OK [01.095]bmp_name=bootlogo.bmp 307254 bytes read in 15 ms (19.5 MiB/s) [01.118]Item0 (Map) magic is bad [01.121]usb burn from boot delay time 0 weak:otg_phy_config [01.133]usb prepare ok [01.340]usb sof ok [01.341]usb probe ok [01.343]usb setup ok set address 0x31 set address 0x31 ok set address 0x32 set address 0x32 ok try to update [04.349]do_burn_from_boot usb : have no handshake partno erro : can't find partition private [04.377]update bootcmd [04.395]update dts Hit any key to stop autoboot: 0 [04.613]no vendor_boot partition is found Android's image name: r329-evb5_pro_v1 [04.856]Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.191 (ubuntu@ubuntu) (gcc version 6.4.1 (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) ) #26 SMP PREEMPT Mon Sep 5 09:22:17 UTC 2022 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] disp reserve base 0x4eb553c0 ,size 0x4b036 [ 0.000000] Reserved memory: created DMA memory pool at 0x0000000043000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vdev0buffer@43000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x0000000043040000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vdev0buffer@43040000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 24 MiB at 0x000000004d000000 [ 0.000000] On node 0 totalpages: 65075 [ 0.000000] DMA zone: 1024 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 65075 pages, LIFO batch:15 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 21 pages/cpu s46360 r8192 d31464 u86016 [ 0.000000] pcpu-alloc: s46360 r8192 d31464 u86016 alloc=21*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64051 [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 initcall_debug=0 console=ttyS0,115200 loglevel=8 ubi.mtd=sys ubi.block=0,rootfs root=/dev/ubiblock0_5 init=/sbin/init rdinit=/rdinit rootfstype=squashfs partitions=mbr@ubi0_0:boot-resource@ubi0_1:env@ubi0_2:env-redund@ubi0_3:boot@ubi0_4:rootfs@ubi0_5:recovery@ubi0_6:UDISK@ubi0_7: cma=24M mac_addr= wifi_mac= bt_mac= selinux=0 specialstr= snum=4c000c5960c30761f0d androidboot.serialno=4c000c5960c30761f0d androidboot.hardware=sun50iw11p1 boot_type=5 androidboot.boot_type=5 androidboot.secure_os_exist=0 gpt=1 uboot_message=2018.05-g6f0ec64(04/27/2022-02:21:36) mbr_offset=1032192 disp_reserve=307254,0x4eb553c0 aw-ubi-spinand.ubootblks=24 androidboot.dramsize=256 [ 0.000000] PID hash table entries: 1024 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.000000] Memory: 213364K/260300K available (5822K kernel code, 486K rwdata, 1648K rodata, 384K init, 229K bss, 22360K reserved, 24576K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008630000 ( 5824 KB) [ 0.000000] .rodata : 0xffffff8008630000 - 0xffffff80087d0000 ( 1664 KB) [ 0.000000] .init : 0xffffff80087d0000 - 0xffffff8008830000 ( 384 KB) [ 0.000000] .data : 0xffffff8008830000 - 0xffffff80088a9808 ( 487 KB) [ 0.000000] .bss : 0xffffff80088a9808 - 0xffffff80088e2cf4 ( 230 KB) [ 0.000000] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc010000000 ( 256 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] clk r_dsp_cache0 not found in of_sunxi_periph_cpus_clk_setup [ 0.000000] clk r_dsp_cache1 not found in of_sunxi_periph_cpus_clk_setup [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.008231] Console: colour dummy device 80x25 [ 0.012410] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.022618] pid_max: default: 32768 minimum: 301 [ 0.027376] Mount-cache hash table entries: 512 (order: 0, 4096 bytes) [ 0.033721] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes) [ 0.041500] sched-energy: CPU device node has no sched-energy-costs [ 0.046922] Invalid sched_group_energy for CPU0 [ 0.051401] CPU0: update cpu_capacity 1024 [ 0.067521] ASID allocator initialised with 32768 entries [ 0.123755] Detected VIPT I-cache on CPU1 [ 0.123805] Invalid sched_group_energy for CPU1 [ 0.123808] CPU1: update cpu_capacity 1024 [ 0.123811] CPU1: Booted secondary processor [410fd034] [ 0.123897] Brought up 2 CPUs [ 0.138998] SMP: Total of 2 processors activated. [ 0.143688] CPU features: detected feature: 32-bit EL0 Support [ 0.149493] CPU features: detected feature: Kernel page table isolation (KPTI) [ 0.158912] CPU: All CPU(s) started at EL1 [ 0.160770] alternatives: patching kernel code [ 0.165332] Invalid sched_group_energy for CPU1 [ 0.169690] Invalid sched_group_energy for Cluster1 [ 0.174539] Invalid sched_group_energy for CPU0 [ 0.179046] Invalid sched_group_energy for Cluster0 [ 0.184370] devtmpfs: initialized [ 0.214666] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.218797] futex hash table entries: 512 (order: 4, 65536 bytes) [ 0.225927] atomic64_test: passed [ 0.228123] pinctrl core: initialized pinctrl subsystem [ 0.234403] NET: Registered protocol family 16 [ 0.238902] dump_class_init,857, success [ 0.253866] cpuidle: using governor menu [ 0.254484] vdso: 2 pages (1 code @ ffffff8008636000, 1 data @ ffffff8008834000) [ 0.260694] DMA: preallocated 256 KiB pool for atomic allocations [ 0.271804] sun50iw11p1-r-pinctrl r_pio: initialized sunXi PIO driver [ 0.280271] sun50iw11p1-pinctrl pio: initialized sunXi PIO driver [ 0.334089] pwm module init! [ 0.338909] sunxi-pm debug v3.10 [ 0.339707] SCSI subsystem initialized [ 0.340571] usbcore: registered new interface driver usbfs [ 0.345909] usbcore: registered new interface driver hub [ 0.351095] usbcore: registered new device driver usb [ 0.356202] sunxi_i2c_adap_init()2649 - init [ 0.360751] sunxi_i2c_probe()2372 - [i2c2] twi_drv_used = 1 [ 0.365833] sunxi_i2c_probe()2379 - [i2c2] twi_pkt_interval = 0 [ 0.371722] twi2 supply twi not found, using dummy regulator [ 0.377425] twi_request_gpio()458 - [i2c2] init name: (null) [ 0.383325] sunxi_i2c_dma_request()1088 - [i2c2] using dma0chan0 (tx) and dma0chan1 (rx)for DMA transfers [ 0.392968] sunxi_i2c_probe()2372 - [i2c1] twi_drv_used = 0 [ 0.398071] sunxi_i2c_probe()2379 - [i2c1] twi_pkt_interval = 0 [ 0.403953] twi1 supply twi not found, using dummy regulator [ 0.409645] twi_request_gpio()458 - [i2c1] init name: (null) [ 0.417006] ion_parse_dt_heap_common: id 0 type 0 name sys_user align 1000 [ 0.422290] ion_parse_dt_heap_common: id 4 type 4 name cma align 1000 [ 0.428642] ion_parse_dt_heap_common: id 6 type 6 name secure align 1000 [ 0.435446] ion_heap_create: Invalid heap type 6 [ 0.440043] Advanced Linux Sound Architecture Driver Initialized. [ 0.446470] Bluetooth: Core ver 2.22 [ 0.449397] NET: Registered protocol family 31 [ 0.453789] Bluetooth: HCI device and connection manager initialized [ 0.460122] Bluetooth: HCI socket layer initialized [ 0.464963] Bluetooth: L2CAP socket layer initialized [ 0.470038] Bluetooth: SCO socket layer initialized [ 0.476380] input: sunxi-keyboard as /devices/virtual/input/input0 [ 0.481823] clocksource: Switched to clocksource arch_sys_counter [ 0.498620] get androidboot.mode fail [ 0.499300] NET: Registered protocol family 2 [ 0.501531] TCP established hash table entries: 16 (order: -5, 128 bytes) [ 0.508053] TCP bind hash table entries: 16 (order: -4, 256 bytes) [ 0.513924] TCP: Hash tables configured (established 16 bind 16) [ 0.519958] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.525722] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.532177] NET: Registered protocol family 1 [ 0.537274] sunxi_spi_probe()2152 - [spi0] SPI MASTER MODE [ 0.541854] spi0 supply spi not found, using dummy regulator [ 0.547454] sunxi_spi_request_gpio()1804 - [spi0] Pinctrl init spi0 [ 0.553669] sunxi_spi_clk_init()1854 - [spi0] mclk 100000000 [ 0.559934] sunxi_spi_probe()2225 - ▒