U-Boot 2018.05-g2a1965a (Jul 10 2022 - 02:50:57 +0000) Allwinner Technology [00.343]CPU: Allwinner Family [00.346]Model: sun8iw20 [00.348]DRAM: 128 MiB [00.352]Relocation Offset is: 04ebc000 [00.377]secure enable bit: 0 [00.380]smc_tee_inform_fdt failed with: -65526[00.384]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz [00.390]gic: sec monitor mode [00.393]flash init start [00.395]workmode = 0,storage type = 1 [00.399][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00 [00.404][mmc]: get sdc_type fail and use default host:tm1. [00.410][mmc]: can't find node "mmc0",will add new node [00.415][mmc]: fdt err returned [00.419][mmc]: Using default timing para [00.422][mmc]: SUNXI SDMMC Controller Version:0x50310 [00.454][mmc]: card_caps:0x3000000a [00.457][mmc]: host_caps:0x3000003f [00.462]sunxi flash init ok [00.465]line:703 init_clocks [00.468]drv_disp_init request pwm success, pwm7:pwm7:0x2000c00. fdt get node offset faill: hdmi [00.484]unable to map hdmi registers [00.487]drv_disp_init finish [00.503]Loading Environment from SUNXI_FLASH... OK [00.522]boot_gui_init:start [00.525]set disp.dev2_output_type fail. using defval=0 [00.531]boot_gui_init:finish partno erro : can't find partition bootloader 54 bytes read in 1 ms (52.7 KiB/s) [00.546]bmp_name=bootlogo.bmp size 38454 38454 bytes read in 3 ms (12.2 MiB/s) [00.562]Item0 (Map) magic is bad [00.564]the secure storage item0 copy0 magic is bad [00.569]Item0 (Map) magic is bad [00.572]the secure storage item0 copy1 magic is bad [00.577]Item0 (Map) magic is bad [00.580]out of usb burn from boot: not need burn key List file under ULI/factory ** Unrecognized filesystem type ** root_partition is rootfs set root to /dev/mmcblk0p5 [00.599]update part info [00.602]update bootcmd [00.606]change working_fdt 0x43e7be70 to 0x43e5be70 disable nand error: FDT_ERR_BADPATH [00.626]update dts Hit any key to stop autoboot: 1 FDT ERROR:get muxsel err returned FDT_ERR_INTERNAL sunxi_pwm_pin_set_state, fdt_set_all_pin, ret=-1 [00.721]LCD open finish 0 [01.809]no vendor_boot partition is found Android's image name: t113-mq_r [01.820]Starting kernel ... [01.823][mmc]: MMC Device 2 not found [01.826][mmc]: mmc 2 not find, so not exit [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.61 (hongduc@ubuntu) (arm-openwrt-linux-muslgnueabi-gcc.bin (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) 6.4.1, GNU ld (GNU Binutils) 2.27) #7 SMP PREEMPT Thu Sep 22 08:07:27 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: sun8iw20 [ 0.000000] printk: bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 4 MiB at 0x47c00000 [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 15 pages/cpu s30348 r8192 d22900 u61440 [ 0.000000] pcpu-alloc: s30348 r8192 d22900 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 rootdelay=2 loglevel=8 root=/dev/mmcblk0p5 init=/pseudo_init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:private@mmcblk0p6:rootfs_data@mmcblk0p7:UDISK@mmcblk0p8 cma=4M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun8iw20p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.05-g2a1965a(07/10/2022-02:50:57) mbr_offset=1032192 disp_reserve=1536000,0x43f06000 androidboot.dramsize=128 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 106048K/131072K available (6144K kernel code, 304K rwdata, 1572K rodata, 1024K init, 1173K bss, 20928K reserved, 4096K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x26c/0x3ec with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.008007] Switching to timer-based delay loop, resolution 41ns [ 0.014182] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.023892] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.034268] pid_max: default: 32768 minimum: 301 [ 0.039018] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.046360] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.054692] CPU: Testing write buffer coherency: ok [ 0.059897] /cpus/cpu@0 missing clock-frequency property [ 0.065223] /cpus/cpu@1 missing clock-frequency property [ 0.070571] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.076730] Setting up static identity map for 0x40100000 - 0x40100060 [ 0.083405] rcu: Hierarchical SRCU implementation. [ 0.088609] smp: Bringing up secondary CPUs ... [ 0.094226] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.094345] smp: Brought up 1 node, 2 CPUs [ 0.104167] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.110344] CPU: All CPU(s) started in SVC mode. [ 0.115411] devtmpfs: initialized [ 0.129754] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.137894] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.147986] pinctrl core: initialized pinctrl subsystem [ 0.154133] NET: Registered protocol family 16 [ 0.160080] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.195128] rtc_ccu: sunxi ccu init OK [ 0.201215] ccu: sunxi ccu init OK [ 0.205054] r_ccu: sunxi ccu init OK [ 0.227874] iommu: Default domain type: Translated [ 0.232919] sunxi iommu: irq = 24 [ 0.237101] SCSI subsystem initialized [ 0.241007] usbcore: registered new interface driver usbfs [ 0.246546] usbcore: registered new interface driver hub [ 0.251947] usbcore: registered new device driver usb [ 0.257684] Advanced Linux Sound Architecture Driver Initialized. [ 0.264344] Bluetooth: Core ver 2.22 [ 0.267966] NET: Registered protocol family 31 [ 0.272429] Bluetooth: HCI device and connection manager initialized [ 0.278814] Bluetooth: HCI socket layer initialized [ 0.283714] Bluetooth: L2CAP socket layer initialized [ 0.288799] Bluetooth: SCO socket layer initialized [ 0.293915] pwm module init! [ 0.297978] g2d 5410000.g2d: Adding to iommu group 0 [ 0.303460] G2D: rcq version initialized.major:252 [ 0.309052] clocksource: Switched to clocksource arch_sys_counter [ 0.323522] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver [ 0.332737] NET: Registered protocol family 2 [ 0.337648] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.346100] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.353829] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.360920] TCP: Hash tables configured (established 1024 bind 1024) [ 0.367379] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.373950] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.381149] NET: Registered protocol family 1 [ 0.386448] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator [ 0.396740] spi spi0: spi0 supply spi not found, using dummy regulator [ 0.403479] sunxi_spi_resource_get()2116 - [spi0] SPI MASTER MODE [ 0.409652] sunxi_spi_resource_get()2154 - Failed to get sample mode [ 0.416005] sunxi_spi_resource_get()2159 - Failed to get sample delay [ 0.422462] sunxi_spi_resource_get()2163 - sample_mode:-1431633921 sample_delay:-1431633921 [ 0.430899] sunxi_spi_clk_init()2205 - [spi0] mclk 100000000 [ 0.437159] sunxi_spi_probe()2623 - [spi0]: driver probe succeed, base c881f000, irq 39 [ 0.446781] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 0.458118] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.464139] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.495806] io scheduler mq-deadline registered [ 0.500372] io scheduler kyber registered [ 0.505415] [DISP]disp_module_init [ 0.509352] disp 5000000.disp: Adding to iommu group 0 [ 0.514993] [DISP] parser_disp_init_para,line:1430: [ 0.514997] of_property_read fb0_width fail [ 0.524100] [DISP] disp_init,line:2386: [ 0.524104] smooth display screen:0 type:1 mode:4 [ 0.548784] display_fb_request,fb_id:0 [ 0.554926] Freeing logo buffer memory: 1500K [ 0.559778] disp_al_manager_apply ouput_type:1 [ 0.564425] sunxi_pwm_enable_dual: can't parse pwm device [ 0.569366] [DISP]disp_module_init finish [ 0.574870] sunxi_sid_init()551 - insmod ok [ 0.580039] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator [ 0.590248] uart uart0: uart0 supply uart not found, using dummy regulator [ 0.597368] uart0: ttyS0 at MMIO 0x2500000 (irq = 34, base_baud = 1500000) is a SUNXI [ 0.605262] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n [ 0.613244] printk: console [ttyS0] enabled [ 0.613244] printk: console [ttyS0] enabled [ 0.622145] printk: bootconsole [earlycon0] disabled [ 0.622145] printk: bootconsole [earlycon0] disabled [ 0.633488] misc dump reg init [ 0.637999] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator [ 0.649266] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9 [ 0.656509] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed [ 0.663866] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed [ 0.671317] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1) [ 0.677860] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power. [ 0.684826] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1) [ 0.692573] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1 [ 0.700444] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1 [ 0.708560] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled [ 0.716200] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power. [ 0.722978] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1) [ 0.730527] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=210 assert=0 [ 0.738505] [ADDR_MGT] addr_mgt_probe: module version: v1.0.11 [ 0.745698] [ADDR_MGT] addr_mgt_probe: success. [ 0.751153] dma-buf: Running sanitycheck [ 0.755552] dma-buf: Running dma_fence [ 0.759780] sizeof(dma_fence)=48 [ 0.763501] dma-buf: Running dma_fence/sanitycheck [ 0.768897] dma-buf: Running dma_fence/test_signaling [ 0.774612] dma-buf: Running dma_fence/test_add_callback [ 0.780586] dma-buf: Running dma_fence/test_late_add_callback [ 0.787040] dma-buf: Running dma_fence/test_rm_callback [ 0.792912] dma-buf: Running dma_fence/test_late_rm_callback [ 0.799306] dma-buf: Running dma_fence/test_status [ 0.804679] dma-buf: Running dma_fence/test_error [ 0.809969] dma-buf: Running dma_fence/test_wait [ 0.815147] dma-buf: Running dma_fence/test_wait_timeout [ 0.859060] dma-buf: Running dma_fence/test_stub [ 0.864257] dma-buf: Running dma_fence/race_signal_callback [ 0.939068] thread_signal_callback[0] completed 36559 passes, 23 misses [ 0.946518] thread_signal_callback[1] completed 36564 passes, 29 misses [ 1.019072] thread_signal_callback[0] completed 41501 passes, 41499 misses [ 1.026803] thread_signal_callback[1] completed 41505 passes, 41505 misses [ 1.035045] sunxi-spinand: AW SPINand MTD Layer Version: 2.3 20211223 [ 1.042337] sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.10 20200306 [ 1.053604] random: fast init done [ 1.310524] random: crng init done [ 2.049108] sunxi-spinand-phy: read id failed : -110 [ 2.054697] spi-nand: probe of spi0.0 failed with error -110 [ 2.061208] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.068531] sunxi-ehci: EHCI SUNXI driver [ 2.073502] get ehci1-controller wakeup-source is fail. [ 2.079491] sunxi ehci1-controller don't init wakeup source [ 2.085748] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xc0b68700, 0x:c8837000, irq_no:3a [ 2.097786] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply drvvbus not found, using dummy regulator [ 2.110294] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator [ 2.122497] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller [ 2.129825] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1 [ 2.139781] sunxi-ehci 4200000.ehci1-controller: irq 58, io mem 0x04200000 [ 2.169083] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00 [ 2.177702] hub 1-0:1.0: USB hub found [ 2.181965] hub 1-0:1.0: 1 port detected [ 2.186918] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.193905] sunxi-ohci: OHCI SUNXI driver [ 2.198859] get ohci1-controller wakeup-source is fail. [ 2.204848] sunxi ohci1-controller don't init wakeup source [ 2.211119] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xc0b68990 [ 2.220819] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply drvvbus not found, using dummy regulator [ 2.233315] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator [ 2.245505] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller [ 2.252779] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2 [ 2.262631] sunxi-ohci 4200400.ohci1-controller: irq 59, io mem 0x04200400 [ 2.343845] hub 2-0:1.0: USB hub found [ 2.348089] hub 2-0:1.0: 1 port detected [ 2.353154] usbcore: registered new interface driver usb-storage [ 2.360062] i2c /dev entries driver [ 2.364048] sunxi cedar version 1.1 [ 2.368132] sunxi-cedar 1c0e000.ve: Adding to iommu group 0 [ 2.374482] VE: sunxi_cedar_probe power-domain init!!! [ 2.380263] VE: install start!!! [ 2.380263] [ 2.385768] VE: cedar-ve the get irq is 40 [ 2.385768] [ 2.392241] VE: ve_debug_proc_info:a450c8b6, data:5550b4a2, lock:1d7da1e2 [ 2.392241] [ 2.401539] VE: install end!!! [ 2.401539] [ 2.406616] VE: sunxi_cedar_probe [ 2.410591] Bluetooth: HCI UART driver ver 2.3 [ 2.415577] Bluetooth: HCI UART protocol H4 registered [ 2.421361] Bluetooth: HCI UART protocol BCSP registered [ 2.427317] Bluetooth: HCI UART protocol (null) registered [ 2.433480] Bluetooth: HCI Realtek H5 protocol initialized [ 2.441742] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.22 2021-12-20 15:40) [ 2.451774] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8 [ 2.457969] sunxi-mmc 4020000.sdmmc: No vmmc regulator found [ 2.464347] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found [ 2.470810] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found [ 2.477254] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found [ 2.483813] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found [ 2.490367] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found [ 2.496914] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found [ 2.503897] sunxi-mmc 4020000.sdmmc: Got CD GPIO [ 2.509466] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.520660] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator [ 2.540813] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.565252] sunxi-mmc 4020000.sdmmc: detmode:gpio irq [ 2.570973] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.583077] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.22 2021-12-20 15:40) [ 2.585623] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.593041] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8 [ 2.606805] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.610679] sunxi-mmc 4021000.sdmmc: No vmmc regulator found [ 2.625236] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.628598] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found [ 2.646652] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found [ 2.653116] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found [ 2.659670] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found [ 2.666211] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found [ 2.672764] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found [ 2.679350] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed [ 2.688799] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.693171] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.699976] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 2.714710] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.728159] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.729094] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.740013] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 2.763275] mmc0: new high speed SDHC card at address aaaa [ 2.764086] sunxi-mmc 4021000.sdmmc: detmode:manually by software [ 2.770387] mmcblk0: mmc0:aaaa SS16G 14.8 GiB [ 2.777038] exFAT: Version 1.3.0 [ 2.785286] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.788611] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 [ 2.798075] sun8iw20-pinctrl 2000000.pinctrl: pin PG18 already requested by 2000000.pinctrl:210; cannot claim for 2036000.spdif [ 2.814806] sun8iw20-pinctrl 2000000.pinctrl: pin-210 (2036000.spdif) status -22 [ 2.823160] sun8iw20-pinctrl 2000000.pinctrl: could not request pin 210 (PG18) from group PG18 on device 2000000.pinctrl [ 2.835487] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.839063] sunxi-spdif 2036000.spdif: Error applying setting, reverse things back [ 2.855621] sunxi-mmc 4021000.sdmmc: card claims to support voltages below defined range [ 2.864768] sunxi-spdif: probe of 2036000.spdif failed with error -22 [ 2.872661] [AUDIOCODEC][sunxi_codec_parse_params][2412]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1 [ 2.872661] [ 2.889889] [AUDIOCODEC][sunxi_codec_parse_params][2448]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0 [ 2.901188] [AUDIOCODEC][sunxi_internal_codec_probe][2609]:codec probe finished [ 2.910332] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present! [ 2.920205] [SNDCODEC][sunxi_card_init][583]:card init finished [ 2.927485] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok [ 2.938454] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input0 [ 2.950421] [SNDCODEC][sunxi_card_dev_probe][836]:register card finished [ 2.959517] NET: Registered protocol family 10 [ 2.965558] Segment Routing with IPv6 [ 2.969724] [SNDCODEC][sunxi_hs_init_work][259]:resume-->report switch [ 2.977071] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.977194] NET: Registered protocol family 17 [ 2.988731] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.999195] Bluetooth: RFCOMM TTY layer initialized [ 3.010859] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 3.010863] Bluetooth: RFCOMM socket layer initialized [ 3.010896] Bluetooth: RFCOMM ver 1.11 [ 3.033325] mmc1: new high speed SDIO card at address 0001 [ 3.033501] Registering SWP/SWPB emulation handler [ 3.059456] sunxi-i2c sunxi-i2c2: sunxi-i2c2 supply twi not found, using dummy regulator [ 3.069322] sunxi-i2c sunxi-i2c2: probe success [ 3.075419] sun8iw20-pinctrl 2000000.pinctrl: pin PG18 already requested by 2000000.pinctrl:210; cannot claim for 2036000.spdif [ 3.088363] sun8iw20-pinctrl 2000000.pinctrl: pin-210 (2036000.spdif) status -22 [ 3.096679] sun8iw20-pinctrl 2000000.pinctrl: could not request pin 210 (PG18) from group PG18 on device 2000000.pinctrl [ 3.108999] sunxi-spdif 2036000.spdif: Error applying setting, reverse things back [ 3.117527] sunxi-spdif: probe of 2036000.spdif failed with error -22 [ 3.125311] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator [ 3.137800] get ehci0-controller wakeup-source is fail. [ 3.143802] sunxi ehci0-controller don't init wakeup source [ 3.150113] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xc0b681e0, 0x:c88a2000, irq_no:38 [ 3.162139] [sunxi-ehci0]: Not init ehci0 [ 3.166975] get ohci0-controller wakeup-source is fail. [ 3.172950] sunxi ohci0-controller don't init wakeup source [ 3.179219] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xc0b68470 [ 3.188893] [sunxi-ohci0]: Not init ohci0 [ 3.195026] get usb_detect_mode is fail, -22 [ 3.199864] get det_vbus is fail, -84 [ 3.203989] get id is fail, -84 [ 3.210030] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 3.219088] clk: Not disabling unused clocks [ 3.219756] cfg80211: failed to load regulatory.db [ 3.224502] ALSA device list: [ 3.233190] #0: audiocodec [ 3.236425] alloc_fd: slot 0 not NULL! [ 3.240845] Waiting 2 sec before mounting root device... [ 4.289071] [ 4.289071] insmod_device_driver [ 4.289071] [ 4.296259] sunxi_usb_udc 4100000.udc-controller: 4100000.udc-controller supply udc not found, using dummy regulator [ 4.308389] device_chose finished 142! [ 5.337257] VFS: Mounted root (squashfs filesystem) readonly on device 179:5. [ 5.351091] devtmpfs: mounted [ 5.356314] Freeing unused kernel memory: 1024K [ 5.369217] Run /pseudo_init as init process mount: mounting none on /dev failed: Resource busy [ 5.803127] EXT4-fs: Warning: mounting with data=journal disables delayed allocation and O_DIRECT support! [ 5.828283] EXT4-fs (mmcblk0p7): mounted filesystem with journalled data mode. Opts: data=journal can't run '/etc/preinit': No such file or directory mount: mounting proc on /proc failed: Resource busy mount: mounting tmpfs on /run failed: No such file or directory hostname: can't open '/etc/hostname': No such file or directory ------run rc.preboot file----- [ 6.324846] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: (null) ------run rc.modules file----- insmod: can't insert '/lib/modules/5.4.61/usb-storage.ko': No such file or directory [ 6.356485] sunxi_gpadc_init,2151, success [ 6.361459] sunxi_gpadc_setup: get channel scan data failed [ 6.368056] input: sunxi-gpadc0 as /devices/virtual/input/input1 [ 6.505790] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success [ 6.612949] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 Successfully initialized wpa_supplicant Could not read interface wlan0 flags: No such device nl80211: Driver does not support authentication/association or connect commands nl80211: deinit ifname=wlan0 disabled_11b_rates=0 Could not read interface wlan0 flags: No such device wlan0: Failed to initialize driver interface ------run rc.final file----- mount: mounting /dev/mmcblk0p1 on /mnt/extsd failed: No such file or directory BusyBox v1.27.2 () built-in shell (ash) ------run profile file----- Trying to connect to SWUpdate... _____ _ __ _ |_ _||_| ___ _ _ | | |_| ___ _ _ _ _ | | _ | || | | |__ | || || | ||_'_| | | | || | || _ | |_____||_||_|_||___||_,_| |_| |_||_|_||_|_| Tina is Based on OpenWrt! ---------------------------------------------- Tina Linux (Neptune, 5C1C9C53) ---------------------------------------------- nodev debugfs root@TinaLinux:/# [ 10.884899] file system registered [ 10.903024] configfs-gadget 4100000.udc-controller: failed to start g1: -19 sh: write error: No such device [ 10.925768] read descriptors [ 10.929016] read strings swu_param: #### swu_software: #### swu_mode: #### no swupdate_cmd to run, wait for next swupdate [ 33.809070] usb1-vbus: disabling root@TinaLinux:/# root@TinaLinux:/#