[130]HELLO! SBOOT is starting!
[133]sboot commit : 54b5c2f5b3 
[136]set pll start
[138]periph0 has been enabled
[141]set pll end
[142]PL gpio voltage : 3.3V 
[145][pmu]: bus read error
[148]PMU: AXP803
[150][pmu]: bus read error
[198]vaild para:1  select dram para0
[202]board init ok, set sys_vol to 950mv!
[226]try to probe rtc region
[229]DRAM BOOT DRIVE INFO: V0.697
[232]the chip id is 0x1400
[235]the chip id is 0x1400
[237]the chip id is 0x1400
[240]the chip id is 0x1400
[242]the chip id is 0x1400
[245]chip id check OK
[255]DRAM_VCC set to 1200 mv
[258]DRAM CLK =744 MHZ
[260]DRAM Type =4 (3:DDR3,4:DDR4,6:LPDDR2,7:LPDDR3,8:LPDDR4)
[269]DRAM SIZE =1024 MBytes, para1 = 60fa, para2 = 4000000, tpr13 = 80007501
[278]DRAM simple test OK.
[280]chipid = 53801400
[283]nsi init ok 2020-4-7
[285][mmc]: mmc driver ver 2020-05-25 09:40-202007019516
[296][mmc]: Wrong media type 0x0
[299][mmc]: ***Try SD card 2***
[303][mmc]: mmc 2 cmd 8 timeout, err 100
[307][mmc]: mmc 2 cmd 8 err 100
[310][mmc]: mmc 2 send if cond failed
[315][mmc]: mmc 2 cmd 55 timeout, err 100
[319][mmc]: mmc 2 cmd 55 err 100
[322][mmc]: mmc 2 send app cmd failed
[326][mmc]: ***Try MMC card 2***
[351][mmc]: RMCA OK!
[353][mmc]: bias 4
[354][mmc]: mmc 2 bias 4
[358][mmc]: MMC 5.1
[360][mmc]: HSSDR52/SDR25 8 bit
[363][mmc]: 50000000 Hz
[365][mmc]: 7456 MB
[367][mmc]: ***SD/MMC 2 init OK!!!***
[399]read toc1 from emmc 32800 sector
[403]OLD version: 0.0
[405]NEW version: 0.0
[468]load rotpk hash
[516]load monitor-key hash
[519]load monitor hash
[673]set arisc reset to assert state
[681]set arisc reset to de-assert state
[733]load boot-key hash
[736]load boot hash
[787]load vbmeta-key hash
[789]load vbmeta hash
[841]load recovery-key hash
[844]load recovery hash
[847]monitor entry=0x48000000
[850]uboot entry=0x4a000000
[853]optee entry=0x48600000
[856]tunning data addr:0x4a0003e8
[859]run out of boot0
NOTICE:  BL3-1: v1.0(debug):0f6655c
NOTICE:  BL3-1: Built : 15:24:20, 2022-07-05
NOTICE:  BL3-1 commit: 8
NOTICE:  info v0.0
NOTICE:  cpuidle init version V1.0
NOTICE:  secure os exist
MESSAGE: [0x0] TEE-CORE: OP-TEE version: f37cc616 #1 Wed Jan 15 03:00:40 UTC 2020 arm
NOTICE:  BL3-1: Preparing for EL3 exit to normal world
NOTICE:  BL3-1: Next image address = 0x4a000000
NOTICE:  BL3-1: Next image spsr = 0x1d3

U-Boot 2018.05 (Jan 11 2023 - 07:09:48 +0000) Allwinner Technology

[00.956]CPU:   Allwinner Family
[00.959]Model: sun50iw10
I2C:   ready
[01.077]DRAM:  1 GiB
[01.080]Relocation Offset is: 35f05000
[01.110]secure enable bit: 1
[01.114][ARISC ERROR] :get [allwinner,sunxi-hwspinlock] device node error
CACHE: Misaligned operation at range [7ffa76e0, 7ffa79f8]
[SCP] :sunxi-arisc driver begin startup 2
[SCP] :0x1
[SCP] :arisc version: [e08bf86ebc1eb22d80c2048eb0805b2501510f7frid-]
[SCP] :arisc startup ready
[SCP] :arisc startup notify message feedback
[SCP] :send hard sync feedback message: 0x900200
[SCP] :sunxi-arisc driver v1.10 is starting
[01.154]pmu_axp806_probe pmic_bus_read fail
[01.158]PMU: AXP803
[01.275]PMU: AXP803
FDT ERROR:fdt_get_regulator_name:get property handle twi-for-pmu-supply error:FDT_ERR_INTERNAL
bias_name:pc_bias	 bias_vol:1800
[01.331]TCS: TCS_probe
[01.333]pmu_tcs4838_probe pmic_bus_read fail
[01.337]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=400Mhz
[01.344]drv_disp_init
request pwm success, pwm0:pwm0:0x300a000.
[01.397]drv_disp_init finish
[01.402]gic: sec monitor mode
[01.405]flash init start
[01.407]workmode = 0,storage type = 2
[01.410][mmc]: mmc driver ver uboot2018:2020-5-25 9:26:00-2021-09-17 14:45:00
[01.418][mmc]: get sdc_type fail and use default host:tm4.
[01.430][mmc]: SUNXI SDMMC Controller Version:0x50300
[01.455][mmc]: Best spd md: 4-HS400, freq: 3-100000000, Bus width: 8
[01.461]sunxi flash init ok
[01.465]Loading Environment from SUNXI_FLASH... OK
[01.472]Item0 (Map) magic is bad
[01.475]the secure storage item0 copy0 magic is bad
[01.479]Item0 (Map) magic is bad
[01.482]the secure storage item0 copy1 magic is bad
[01.487]Item0 (Map) magic is bad
secure storage read widevine fail
[01.493]secure storage read widevine fail with:-1
secure storage read ec_key fail
[01.500]secure storage read ec_key fail with:-1
[01.505]usb burn from boot
delay time 0
weak:otg_phy_config
[01.516]usb prepare ok
[01.950]usb sof ok
[01.952]usb probe ok
[01.953]usb setup ok
set address 0x1a
set address 0x1a ok
try to update 
[04.960]do_burn_from_boot usb : have no handshake
[04.964]boot_gui_init:start
[04.969]set disp.dev2_output_type fail. using defval=0
[04.978]boot_gui_init:finish
[04.980]bmp_name=bootlogo.bmp
4096056 bytes read in 25 ms (156.3 MiB/s)
no support big size bmp[800x1280] on fb[1024x600]
[05.016]show bm[05.018]soc ic_ver:0x4, qa_val:0x0, markid:0x1400 dclk[0-200] display_cfg_flag:0
p on fb failed !-1
[05.034]update dts
** Unrecognized filesystem type **
[05.043]load file(ULI/factory/snum.txt) error.
** Unrecognized filesystem type **
[05.056]load file(ULI/factory/mac.txt) error.
** Unrecognized filesystem type **
[05.068]load file(ULI/factory/wifi_mac.txt) error.
** Unrecognized filesystem type **
[05.080]load file(ULI/factory/bt_mac.txt) error.
** Unrecognized filesystem type **
[05.093]load file(ULI/factory/specialstr.txt) error.
[05.103]update part info
[05.126]update bootcmd
Hit any key to stop autoboot:  0 
[05.228]LCD open finish
[05.352]not supported key
[05.354]actual n size:1000, e:10001
[05.357]exptect n size:800, e:10001
CACHE: Misaligned operation at range [44ffffe0, 465c9020]
[05.563]Starting kernel ...

[05.566][mmc]: mmc exit start
[05.585][mmc]: mmc 2 exit ok