CCC[2354]fes begin commit:4b419f21ba
[2358]PMU: AXP21
[2361]set pll start
[2363]periph0 has been enabled
[2366]set pll end
[2368]board init ok
[2369]beign to init dram
[2372]DRAM use external ZQ!!
[2374]chip id check OK
[2377]DRAM_VCC set to 1500 mv
[2380]trefi:7.8ms
[2382][AUTO DEBUG] single rank and full DQ!
[2387]trefi:7.8ms
[2389][AUTO DEBUG] rank 0 row = 15
[2392][AUTO DEBUG] rank 0 bank = 8
[2396][AUTO DEBUG] rank 0 page size = 2 KB
[2400]DRAM BOOT DRIVE INFO: V0.16
[2403]DRAM CLK = 936 MHz
[2405]DRAM Type = 3 (2:DDR2,3:DDR3)
[2409]DRAMC ZQ value: 0x7b7bfb
[2411]DRAM ODT value: 0x42.
[2415]DRAM SIZE =512 M
[2417]dram_tpr4:0x0
[2420]DRAM simple test OK.
[2423]rtc standby flag is 0x0, super standby flag is 0x0
[2428]init dram ok


U-Boot 2018.05 (Apr 25 2023 - 11:52:11 +0800) Allwinner Technology

[04.858]CPU:   Allwinner Family
[04.861]Model: sun8iw21
I2C:   ready
[04.888]DRAM:  512 MiB
[04.891]Relocation Offset is: 1ced0000
[04.916]secure enable bit: 0
[04.918]PMU: AXP21
[04.920]PMU: pmu_axp2101 found
[04.923]BMU: AXP21
[04.924]BMU: bmu_axp2101 found
FDT ERROR:fdt_get_regulator_name:get property handle twi-supply error:FDT_ERR_INTERNAL
[04.935]gpio_bias, pc_bias: 1800, pc_supply: not set
[04.940]gpio_bias, pl_bias:   -1, pl_supply: not set
[04.946]dcdc1_vol = 3300, onoff=1
[04.949]dcdc2_vol = 900, onoff=1
[04.952]dcdc5_vol = 0, onoff=0
[04.956]aldo1_vol = 1800, onoff=1
[04.959]aldo2_vol = 1800, onoff=1
[04.963]aldo3_vol = 3300, onoff=1
[04.966]aldo4_vol = 3300, onoff=1
[04.970]bldo1_vol = 1800, onoff=1
[04.973]bldo2_vol = 2800, onoff=1
[04.977]dldo1_vol = 3300, onoff=1
[04.980]dldo2_vol = 1200, onoff=1
bias_name:pc_bias        bias_vol:1800
bias_name:pi_bias        bias_vol:1800
[04.990]bat_vol=36, ratio=0
[04.993]safe_vol=3500, safe_ratio=1
[04.996]CPU=900 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=24Mhz  MBus=300Mhz
[05.002]gic: normal mode
sunxi flash map init
[05.007]flash init start
[05.009]workmode = 16,storage type = 0
try card 2
set card number 2
get card number 2
[05.017][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00
[05.022][mmc]: get sdc_type fail and use default host:tm4.
[05.029][mmc]: Is not Boot mode!
[05.032][mmc]: SUNXI SDMMC Controller Version:0x50400
[05.043][mmc]: ************Try SD card 2************
[05.048][mmc]: mmc 2 cmd timeout 100 status 100
[05.052][mmc]: smc 2 err, cmd 8,  RTO
[05.056][mmc]: mmc 2 close bus gating and reset
[05.061][mmc]: mmc 2 cmd timeout 100 status 100
[05.065][mmc]: smc 2 err, cmd 55,  RTO
[05.068][mmc]: mmc 2 close bus gating and reset
[05.072][mmc]: ************Try MMC card 2************
[05.096][mmc]: mmc 2 cmd timeout 100 status 100
[05.100][mmc]: smc 2 err, cmd 8,  RTO
[05.103][mmc]: mmc 2 close bus gating and reset
[05.108][mmc]: mmc 2 cmd timeout 100 status 100
[05.112][mmc]: smc 2 err, cmd 55,  RTO
[05.116][mmc]: mmc 2 close bus gating and reset
[05.131][mmc]: gen_tuning_blk_bus8: total blk 10
[05.136][mmc]: gen_tuning_blk_bus4: total blk 6
[05.140][mmc]: Using 8 bit tuning now
[05.144][mmc]: write_tuning_try_freq: write ok
[05.148][mmc]: Pattern compare ok
[05.151][mmc]: Write tuning pattern ok
[05.155][mmc]: ================== HSSDR52_SDR25...
[05.159][mmc]: skip freq 400000
[05.162][mmc]: skip freq 25000000
[05.165][mmc]: freq: 2-50000000-64-4
[05.314][mmc]: [0-53|54] [61-63|3]
[05.317][mmc]: ================== HSDDR52_DDR50...
[05.321][mmc]: skip freq 400000
[05.324][mmc]: freq: 1-25000000-64-4
[05.465][mmc]: freq: 2-50000000-64-4
[05.556][mmc]: [0-50|51] [62-63|2]
[05.559][mmc]: [0-30|31] [32-50|19] [62-63|2]
[05.564][mmc]: DS26/SDR12: 0xffffffff 0xffffffff
[05.568][mmc]: HSSDR52/SDR25: 0xff1bffff 0xffffffff
[05.573][mmc]: HSDDR52/DDR50: 0xff0f19ff 0xffffffff
[05.577][mmc]: HS200/SDR104: 0xffffffff 0xffffffff
[05.582][mmc]: HS400: 0xffffffff 0xffffffff
[05.586][mmc]: HS400: 0xffffffff 0xffffffff
[05.590][mmc]: Best spd md: 2-HSDDR52/DDR50, freq: 2-50000000, Bus width: 8
[05.596]line:724 init_clocks
[05.599]init_clocks:finish
[05.602]Loading Environment from SUNXI_FLASH... OK
[05.606]try to burn key
[05.608]out of usb burn from boot: not need burn key
Hit any key to stop autoboot:  0
sunxi work mode=0x10
run usb efex
delay time 2500
weak:otg_phy_config
usb init ok
set address 0x3b
set address 0x3c
set address 0x3c ok
set address 0x3d
set address 0x3d ok