[3625]fes begin commit:97444f5 [3628]set pll start [3630]periph0 has been enabled [3633]set pll end [3635]board init ok [3637]beign to init dram [3639]the chip id is 0x2 [3642]the chip id is 0x2 [3644]the chip id is 0x2 [3646]the chip id is 0x2 [3649]the chip id is 0x2 [3651]chip id check OK [3654][AUTO DEBUG] two rank and full DQ! [3658][AUTO DEBUG] DDR3 try success [3662][AUTO DEBUG] single rank and full DQ! [3666][AUTO DEBUG] rank 0 row = 13 [3670][AUTO DEBUG] rank 0 bank = 8 [3673][AUTO DEBUG] rank 0 page size = 2 KB [3677]DRAM BOOT DRIVE INFO: V0.171 [3680]DRAM Type = 3 (2:DDR2,3:DDR3) [3683]DRAMC read ODT off. [3686]DRAM ODT off. [3689]DRAM CLK = 774 MHz [3691]DRAM SIZE =128 M [3694]DRAM simple test OK. [3697]init dram ok U-Boot 2018.05-00013-g7af46550cd (Dec 25 2020 - 08:28:52 +0000) Allwinner Technology [05.885]CPU: Allwinner Family [05.888]Model: sun50iw11 I2C: ready [06.011]DRAM: 128 MiB [06.014]Relocation Offset is: 04eff000 [06.036]secure enable bit: 0 [06.039]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=0Mhz [06.050]gic: normal mode [06.052]flash init start [06.054]workmode = 16,storage type = 0 try card 0 set card number 0 get card number 0 [06.062][mmc]: mmc driver ver uboot2018:2020-10-22 16:39:00 [06.073][mmc]: Using default timing para [06.076][mmc]: SUNXI SDMMC Controller Version:0x50300 [06.090][mmc]: mmc 0 cmd timeout 100 status 100 [06.094][mmc]: smc 0 err, cmd 8, RTO [06.097][mmc]: mmc 0 close bus gating and reset [06.102][mmc]: mmc 0 cmd timeout 100 status 100 [06.106][mmc]: smc 0 err, cmd 55, RTO [06.109][mmc]: mmc 0 close bus gating and reset [06.117][mmc]: mmc 0 cmd timeout 100 status 100 [06.121][mmc]: smc 0 err, cmd 1, RTO [06.125][mmc]: mmc 0 close bus gating and reset [06.129][mmc]: Card did not respond to voltage select! [06.134][mmc]: mmc_init: -95, time 53 [06.137][mmc]: mmc_init: mmc init fail, err -95 MMC init failed try emmc fail [06.145]sunxi-spinand: AW SPINand MTD Layer Version: 1.5 20200407 [06.151]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.9 20200306 [06.162]sunxi-spinand-phy: request spi0 gpio ok [06.166]sunxi-spinand-phy: request general tx dma channel ok! [06.172]sunxi-spinand-phy: request general rx dma channel ok! [06.177]sunxi-spinand-phy: set spic0 clk to 20 Mhz [06.182]sunxi-spinand-phy: init spic0 clk ok [06.186]sunxi-spinand-phy: not detect any munufacture from id table [06.193]sunxi-spinand-phy: get spi-nand Model from fdt fail [06.198]sunxi-spinand-phy: get phy info from fdt fail [06.203]sunxi-spinand-phy: not detect munufacture from fdt [06.208]sunxi-spinand-phy: detect munufacture from id table: GD [06.214]sunxi-spinand-phy: detect spinand id: ffffd1c8 ffffffff [06.219]sunxi-spinand-phy: ========== arch info ========== [06.224]sunxi-spinand-phy: Model: GD5F1GQ4UBYIG [06.230]sunxi-spinand-phy: Munufacture: GD [06.234]sunxi-spinand-phy: DieCntPerChip: 1 [06.239]sunxi-spinand-phy: BlkCntPerDie: 1024 [06.243]sunxi-spinand-phy: PageCntPerBlk: 64 [06.248]sunxi-spinand-phy: SectCntPerPage: 4 [06.252]sunxi-spinand-phy: OobSizePerPage: 64 [06.257]sunxi-spinand-phy: BadBlockFlag: 0x0 [06.262]sunxi-spinand-phy: OperationOpt: 0x7 [06.266]sunxi-spinand-phy: MaxEraseTimes: 50000 [06.271]sunxi-spinand-phy: EccFlag: 0x1 [06.275]sunxi-spinand-phy: EccType: 7 [06.280]sunxi-spinand-phy: EccProtectedType: 4 [06.284]sunxi-spinand-phy: ======================================== [06.290]sunxi-spinand-phy: [06.293]sunxi-spinand-phy: ========== physical info ========== [06.298]sunxi-spinand-phy: TotalSize: 128 M [06.303]sunxi-spinand-phy: SectorSize: 512 B [06.307]sunxi-spinand-phy: PageSize: 2 K [06.311]sunxi-spinand-phy: BlockSize: 128 K [06.315]sunxi-spinand-phy: OOBSize: 64 B [06.319]sunxi-spinand-phy: ======================================== [06.325]sunxi-spinand-phy: [06.327]sunxi-spinand-phy: ========== logical info ========== [06.333]sunxi-spinand-phy: TotalSize: 128 M [06.337]sunxi-spinand-phy: SectorSize: 512 B [06.341]sunxi-spinand-phy: PageSize: 4 K [06.345]sunxi-spinand-phy: BlockSize: 256 K [06.349]sunxi-spinand-phy: OOBSize: 128 B [06.353]sunxi-spinand-phy: ======================================== [06.361]sunxi-spinand-phy: set spic0 clk to 100 Mhz [06.365]sunxi-spinand-phy: block lock register: 0x00 [06.370]sunxi-spinand-phy: feature register: 0x11 [06.374]sunxi-spinand-phy: sunxi physic nand init end [06.380]Loading Environment from SUNXI_FLASH... OK [06.384]try to burn key [06.387]out of usb burn from boot: not boot mode Hit any key to stop autoboot: 0 sunxi work mode=0x10 run usb efex delay time 2500 weak:otg_phy_config usb init ok set address 0x26 set address 0x26 ok SUNXI_EFEX_ERASE_TAG erase_flag = 0x1 origin_erase_flag = 0x0 FEX_CMD_fes_verify_status FEX_CMD_fes_verify last err=0 the 0 mbr table is ok the 1 mbr table is ok the 2 mbr table is ok the 3 mbr table is ok *************MBR DUMP*************** total mbr part 11 part[0] name :boot-resource part[0] classname :DISK part[0] addrlo :0x1f8 part[0] lenlo :0x3f0 part[0] user_type :32768 part[0] keydata :0 part[0] ro :0 part[1] name :env part[1] classname :DISK part[1] addrlo :0x5e8 part[1] lenlo :0x1f8 part[1] user_type :32768 part[1] keydata :0 part[1] ro :0 part[2] name :env-redund part[2] classname :DISK part[2] addrlo :0x7e0 part[2] lenlo :0x1f8 part[2] user_type :32768 part[2] keydata :0 part[2] ro :0 part[3] name :boot part[3] classname :DISK part[3] addrlo :0x9d8 part[3] lenlo :0x2760 part[3] user_type :32768 part[3] keydata :0 part[3] ro :0 part[4] name :rootfs part[4] classname :DISK part[4] addrlo :0x3138 part[4] lenlo :0xf12c part[4] user_type :32768 part[4] keydata :0 part[4] ro :0 part[5] name :dsp0 part[5] classname :DISK part[5] addrlo :0x12264 part[5] lenlo :0x9d8 part[5] user_type :32768 part[5] keydata :0 part[5] ro :0 part[6] name :dsp1 part[6] classname :DISK part[6] addrlo :0x12c3c part[6] lenlo :0x9d8 part[6] user_type :32768 part[6] keydata :0 part[6] ro :0 part[7] name :dsp0-r part[7] classname :DISK part[7] addrlo :0x13614 part[7] lenlo :0x9d8 part[7] user_type :32768 part[7] keydata :0 part[7] ro :0 part[8] name :dsp1-r part[8] classname :DISK part[8] addrlo :0x13fec part[8] lenlo :0x9d8 part[8] user_type :32768 part[8] keydata :0 part[8] ro :0 part[9] name :recovery part[9] classname :DISK part[9] addrlo :0x149c4 part[9] lenlo :0x6e40 part[9] user_type :32768 part[9] keydata :0 part[9] ro :0 part[10] name :UDISK part[10] classname :DISK part[10] addrlo :0x1b804 part[10] lenlo :0x0 part[10] user_type :33024 part[10] keydata :0 part[10] ro :0 total part: 12 mbr 0, 1f8, 8000 boot-resource 1, 3f0, 8000 env 2, 1f8, 8000 env-redund 3, 1f8, 8000 boot 4, 2760, 8000 rootfs 5, f12c, 8000 dsp0 6, 9d8, 8000 dsp1 7, 9d8, 8000 dsp0-r 8, 9d8, 8000 dsp1-r 9, 9d8, 8000 recovery 10, 6e40, 8000 UDISK 11, 0, 8100 [09.495]erase blk 0 to blk 32 need erase flash: 1 [09.558]mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,512k@5242880(pstore)ro,-(sys) device nand0 , # parts = 5 #: name size offset mask_flags 0: boot0 0x00100000 0x00000000 1 1: uboot 0x00300000 0x00100000 1 2: secure_storage 0x00100000 0x00400000 1 3: pstore 0x00080000 0x00500000 1 4: sys 0x07a80000 0x00580000 0 active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000 defaults: mtdids : nand0=nand mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,512k@5242880(pstore)ro,-(sys) [09.617]MTD info (5) [09.619]pagesize: 0x1000 [09.621]blksize: 0x40000 [09.623]num offset bytes name [09.627]0 0x00000000 0x00100000 boot0 [09.630]1 0x00100000 0x00300000 uboot [09.634]2 0x00400000 0x00100000 secure_storage [09.638]3 0x00500000 0x00080000 pstore [09.642]4 0x00580000 0x07a80000 sys [09.646]ubi attach the last part of mtd device: NO.4 [09.729]ubi0: attaching mtd5 [09.785]ubi0: scanning is finished [09.788]ubi0: empty MTD device detected [09.811]ubi0: attached mtd5 (name "sys", size 122 MiB) [09.816]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes [09.822]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048 [09.828]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [09.835]ubi0: good PEBs: 489, bad PEBs: 1, corrupted PEBs: 0 [09.840]ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128 [09.847]ubi0: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 0 [09.854]ubi0: available PEBs: 466, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19 no part need to protect user data [11.786]erase blk 0 to blk 32 [11.844]erase blk 40 to blk 1024 [13.558]blk 1023 is bad, skip to erase SUNXI_EFEX_MBR_TAG mbr size = 0x10000 force mbr device nand0 , # parts = 5 #: name size offset mask_flags 0: boot0 0x00100000 0x00000000 1 1: uboot 0x00300000 0x00100000 1 2: secure_storage 0x00100000 0x00400000 1 3: pstore 0x00080000 0x00500000 1 4: sys 0x07a80000 0x00580000 0 active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000 defaults: mtdids : nand0=nand mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,512k@5242880(pstore)ro,-(sys) [13.613]MTD info (5) [13.614]pagesize: 0x1000 [13.617]blksize: 0x40000 [13.619]num offset bytes name [13.623]0 0x00000000 0x00100000 boot0 [13.626]1 0x00100000 0x00300000 uboot [13.630]2 0x00400000 0x00100000 secure_storage [13.634]3 0x00500000 0x00080000 pstore [13.638]4 0x00580000 0x07a80000 sys [13.641]MBR info (unalign): [13.644]partno addr sects type name [13.649]0 0x00000000 0x000001f8 0x00000001 mbr [13.654]1 0x000001f8 0x000003f0 0x00008000 boot-resource [13.659]2 0x000005e8 0x000001f8 0x00008000 env [13.664]3 0x000007e0 0x000001f8 0x00008000 env-redund [13.669]4 0x000009d8 0x00002760 0x00008000 boot [13.674]5 0x00003138 0x0000f12c 0x00008000 rootfs [13.679]6 0x00012264 0x000009d8 0x00008000 dsp0 [13.684]7 0x00012c3c 0x000009d8 0x00008000 dsp1 [13.689]8 0x00013614 0x000009d8 0x00008000 dsp0-r [13.694]9 0x00013fec 0x000009d8 0x00008000 dsp1-r [13.699]10 0x000149c4 0x00006e40 0x00008000 recovery [13.704]11 0x0001b804 0x00000000 0x00008100 UDISK [13.709]ubi attach the last part of mtd device: NO.4 [13.714]MBR info (align): [13.716]partno addr sects type name [13.721]0 0x00002c00 0x000001f8 0x00000001 mbr [13.726]1 0x00002df8 0x000003f0 0x00008000 boot-resource [13.731]2 0x000031e8 0x000001f8 0x00008000 env [13.736]3 0x000033e0 0x000001f8 0x00008000 env-redund [13.742]4 0x000035d8 0x00002760 0x00008000 boot [13.746]5 0x00005d38 0x0000f228 0x00008000 rootfs [13.751]6 0x00014f60 0x000009d8 0x00008000 dsp0 [13.756]7 0x00015938 0x000009d8 0x00008000 dsp1 [13.761]8 0x00016310 0x000009d8 0x00008000 dsp0-r [13.766]9 0x00016ce8 0x000009d8 0x00008000 dsp1-r [13.771]10 0x000176c0 0x00006e40 0x00008000 recovery [13.776]11 0x0001e500 0x00000000 0x00008100 UDISK [13.781]ubi attach the last part of mtd device: NO.4 [13.786]ubi attatch mtd, name: sys [13.789]ubi0: detaching mtd5 [13.792]ubi0: mtd5 is detached [13.795]ubi0: attaching mtd5 [13.851]ubi0: scanning is finished [13.854]ubi0: empty MTD device detected [13.877]ubi0: attached mtd5 (name "sys", size 122 MiB) [13.882]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes [13.888]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048 [13.894]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [13.901]ubi0: good PEBs: 489, bad PEBs: 1, corrupted PEBs: 0 [13.906]ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128 [13.913]ubi0: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 0 [13.920]ubi0: available PEBs: 466, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19 Creating static volume mbr of size 258048 Creating dynamic volume boot-resource of size 516096 Creating dynamic volume env of size 258048 Creating dynamic volume env-redund of size 258048 Creating dynamic volume boot of size 5160960 Creating dynamic volume rootfs of size 31739904 Creating dynamic volume dsp0 of size 1290240 Creating dynamic volume dsp1 of size 1290240 Creating dynamic volume dsp0-r of size 1290240 Creating dynamic volume dsp1-r of size 1290240 Creating dynamic volume recovery of size 14450688 No size specified -> Using max size (62447616) [16.139]reset last volume size to 0x1dc70 Creating dynamic volume UDISK of size 62447616 [16.191]fill gap start: volume mbr sects 0x178 [16.293]fill gap end: volume mbr [16.296]update partition map [16.298]logical area info: 466 258048 last_lba: 234863 [16.307]logical area info: 466 258048 last_lba: 234863 [16.315]logical area info: 466 258048 last_lba: 234863 [16.323]logical area info: 466 258048 last_lba: 234863 [16.332]logical area info: 466 258048 last_lba: 234863 [16.340]logical area info: 466 258048 last_lba: 234863 [16.348]logical area info: 466 258048 last_lba: 234863 [16.357]logical area info: 466 258048 last_lba: 234863 [16.365]logical area info: 466 258048 last_lba: 234863 [16.373]logical area info: 466 258048 last_lba: 234863 [16.382]logical area info: 466 258048 last_lba: 234863 [16.390]logical area info: 466 258048 last_lba: 234863 [16.398]logical area info: 466 258048 last_lba: 234863 [16.407]logical area info: 466 258048 last_lba: 234863 [16.415]logical area info: 466 258048 last_lba: 234863 [16.423]logical area info: 466 258048 last_lba: 234863 [16.432]logical area info: 466 258048 last_lba: 234863 [16.440]logical area info: 466 258048 last_lba: 234863 [16.448]logical area info: 466 258048 last_lba: 234863 [16.457]logical area info: 466 258048 last_lba: 234863 [16.465]logical area info: 466 258048 last_lba: 234863 [16.473]logical area info: 466 258048 last_lba: 234863 [16.481]logical area info: 466 258048 last_lba: 234863 [16.490]logical area info: 466 258048 last_lba: 234863 [16.498]logical area info: 466 258048 last_lba: 234863 [16.506]logical area info: 466 258048 last_lba: 234863 [16.515]logical area info: 466 258048 last_lba: 234863 [16.523]logical area info: 466 258048 last_lba: 234863 [16.531]logical area info: 466 258048 last_lba: 234863 [16.540]logical area info: 466 258048 last_lba: 234863 [16.548]logical area info: 466 258048 last_lba: 234863 [16.556]logical area info: 466 258048 last_lba: 234863 [16.565]logical area info: 466 258048 last_lba: 234863 [16.573]logical area info: 466 258048 last_lba: 234863 [16.581]logical area info: 466 258048 last_lba: 234863 [16.590]logical area info: 466 258048 last_lba: 234863 [16.598]logical area info: 466 258048 last_lba: 234863 FEX_CMD_fes_verify_status FEX_CMD_fes_verify last err=0 [16.713]fill gap start: volume boot-resource sects 0x142 [16.798]fill gap end: volume boot-resource FEX_CMD_fes_verify_value, start 0x1f8, size high 0x0:low 0x55c00 FEX_CMD_fes_verify_value 0x22eca6c0 [16.883]fill gap start: volume env sects 0xf8 [16.967]fill gap end: volume env FEX_CMD_fes_verify_value, start 0x5e8, size high 0x0:low 0x20000 FEX_CMD_fes_verify_value 0xabc03478 [17.017]fill gap start: volume env-redund sects 0xf8 [17.102]fill gap end: volume env-redund FEX_CMD_fes_verify_value, start 0x7e0, size high 0x0:low 0x20000 FEX_CMD_fes_verify_value 0xabc03478 [18.086]fill gap start: volume boot sects 0x9e0 [18.462]fill gap end: volume boot FEX_CMD_fes_verify_value, start 0x9d8, size high 0x0:low 0x3b0000 FEX_CMD_fes_verify_value 0xd3227166 [25.575]fill gap start: volume rootfs sects 0x242c [26.680]fill gap end: volume rootfs FEX_CMD_fes_verify_value, start 0x3138, size high 0x0:low 0x19a0000 FEX_CMD_fes_verify_value 0x4b0c498a