[28]HELLO! BOOT0 is starting! [31]BOOT0 commit : 2386bdb825 [34]set pll start [40]periph0 has been enabled [43]set pll end [44][pmu]: bus read error [47]board init ok [49]enable_jtag [50]ZQ value = 0x2f [52]get_pmu_exist() = -1 [54]DRAM BOOT DRIVE INFO: V0.34 [57]DRAM CLK = 792 MHz [60]DRAM Type = 3 (2:DDR2,3:DDR3) [63]DRAMC read ODT off. [65]DRAM ODT value: 0x42. [68]ddr_efuse_type: 0xa [71]DRAM SIZE = 128 MB [77]DRAM simple test OK. [80]rtc standby flag is 0x0, super standby flag is 0x0 [85]dram size =128 [87]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32 [93]block from 8 to 32 [225]Check is correct. Find a good uboot copy at block 8 [230]dma 0x2b424 int is not used yet [233]dma 0x2b424 int is free, you do not need to free it again [239]Entry_name = u-boot [246]Entry_name = optee [250]Entry_name = dtb [253]Jump to second Boot. M/TC: OP-TEE version: aa2ed4e9 (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Mon Jan 13 06:39:29 UTC 2025 arm M/TC: OP-TEE 32bit E/TC:0 0 search_key_via_name:418 Key 'huk' not found E/TC:0 0 platform_standby_fdt_parse:126 no pmu0 node E/TC:0 0 sunxi_twi_parse_from_dt:121 no pmu node U-Boot 2018.07-gce06dac (Mar 15 2025 - 06:33:14 +0000) Allwinner Technology [00.330]CPU: Allwinner Family [00.333]Model: sun8iw20 [00.336]DRAM: 128 MiB [00.339]Relocation Offset is: 04ec3000 [00.366]secure enable bit: 0 CACHE: Misaligned operation at range [44882e68, 448a2e68] E/TC:0 generate_smc_mem_map:319 Not enough SMC region, 0x41b07937 byte ta ram left unsecured E/TC:0 fdt_getprop_u32:340 prop trace_level not found [00.393]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz [00.399]gic: sec monitor mode [00.402]line:703 init_clocks [00.405]flash init start [00.407]workmode = 0,storage type = 0 [00.414]sunxi-spinand-phy: spinand sample_mode:2 sample_delay:4 device nand0 , # parts = 4 #: name size offset mask_flags 0: boot0 0x00100000 0x00000000 1 1: uboot 0x00300000 0x00100000 1 2: secure_storage 0x00100000 0x00400000 1 3: sys 0x0fb00000 0x00500000 0 active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000 defaults: mtdids : nand0=nand mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys) [00.462]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [00.572]ubi0: attaching mtd4 [00.997]ubi0: scanning is finished [01.006]ubi0: attached mtd4 (name "sys", size 251 MiB) [01.011]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes [01.017]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048 [01.024]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [01.030]ubi0: good PEBs: 997, bad PEBs: 7, corrupted PEBs: 0 [01.035]ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128 [01.042]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0 [01.050]ubi0: available PEBs: 0, total reserved PEBs: 997, PEBs reserved for bad PEB handling: 33 [01.058]sunxi flash init ok [01.061]drv_disp_init partno erro : can't find partition bootloader ** Unable to read file lcd_compatible_index.txt ** [01.308]disp_fat_load for lcd config failed [01.333]drv_disp_init finish [01.524]Loading Environment from SUNXI_FLASH... OK [01.559]boot_gui_init:start partno erro : can't find partition Reserve0 bad fb1_cfg[w=0,h=0,bpp=32,format=0] [01.635]boot_gui_init:finish partno erro : can't find partition bootloader [01.663]bmp_name=bootlogo.bmp size 1152054 [01.772]LCD open finish [01.799]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [01.804]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [01.808]sunxi-spinand: check valid secure storage failed with 32 back [01.815]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [01.819]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [01.824]sunxi-spinand: nand secure storage check page 0 fail [01.829]sunxi-spinand: check secure storage failed with -22 [01.834]get secure storage map err [01.837]sunxi_secure_storage_read err: secure storage has not been inited secure storage read widevine fail [01.847]sunxi_secure_storage_read err: secure storage has not been inited secure storage read ec_key fail [01.856]sunxi_secure_storage_read err: secure storage has not been inited secure storage read ec_cert1 fail [01.866]sunxi_secure_storage_read err: secure storage has not been inited secure storage read ec_cert2 fail [01.875]sunxi_secure_storage_read err: secure storage has not been inited secure storage read ec_cert3 fail [01.885]sunxi_secure_storage_read err: secure storage has not been inited secure storage read rsa_key fail [01.894]sunxi_secure_storage_read err: secure storage has not been inited secure storage read rsa_cert1 fail [01.904]sunxi_secure_storage_read err: secure storage has not been inited secure storage read rsa_cert2 fail [01.914]sunxi_secure_storage_read err: secure storage has not been inited secure storage read rsa_cert3 fail [01.923]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [01.928]sunxi-spinand: check valid secure storage failed with 32 back [01.934]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [01.939]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [01.943]sunxi-spinand: nand secure storage check page 0 fail [01.949]sunxi-spinand: check secure storage failed with -22 [01.954]get secure storage map err [01.957]sunxi secure storage is not supported [01.961]usb burn from boot delay time 0 weak:otg_phy_config [01.972]usb prepare ok [02.237]usb sof ok [02.238]usb probe ok [02.240]usb setup ok set address 0x3c set address 0x3c ok try to update [02.645]do_burn_from_boot usb : have no handshake [02.649]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [02.654]sunxi-spinand: check valid secure storage failed with 32 back [02.660]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [02.665]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [02.669]sunxi-spinand: nand secure storage check page 0 fail [02.675]sunxi-spinand: check secure storage failed with -22 [02.680]get secure storage map err List file under ULI/factory ** Unrecognized filesystem type ** [02.689]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [02.693]sunxi-spinand: check valid secure storage failed with 32 back [02.700]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [02.704]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [02.709]sunxi-spinand: nand secure storage check page 0 fail [02.714]sunxi-spinand: check secure storage failed with -22 [02.719]get secure storage map err [02.723]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [02.727]sunxi-spinand: check valid secure storage failed with 32 back [02.733]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [02.738]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [02.743]sunxi-spinand: nand secure storage check page 0 fail [02.748]sunxi-spinand: check secure storage failed with -22 [02.753]get secure storage map err [02.756]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [02.761]sunxi-spinand: check valid secure storage failed with 32 back [02.767]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [02.772]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [02.776]sunxi-spinand: nand secure storage check page 0 fail [02.782]sunxi-spinand: check secure storage failed with -22 [02.787]get secure storage map err [02.790]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [02.795]sunxi-spinand: check valid secure storage failed with 32 back [02.801]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [02.806]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [02.810]sunxi-spinand: nand secure storage check page 0 fail [02.816]sunxi-spinand: check secure storage failed with -22 [02.821]get secure storage map err [02.845]update bootcmd [02.875]change working_fdt 0x44882e68 to 0x44862e68 partno erro : can't find partition bootloader ** Unable to read file lcd_compatible_index.txt ** [02.932]disp_fat_load for lcd config failed partno erro : can't find partition bootloader writing lcd_compatible_index.txt [02.966]offset should be 0 but 0x6d6d when write to new volume boot-resource Error: writing contents ** Unable to write "lcd_compatible_index.txt" from sunxi_flash 0:1 ** [02.981]do_fat_fswrite for lcd config failed partno erro : can't find partition bootloader ** Unable to read file lcd_compatible_index.txt ** [03.015]disp_fat_load for lcd config failed [03.020]update dts Hit any key to stop autoboot: 0 [04.393]no vendor_boot partition is found Android's image name: sun8i_arm ERROR: reserving fdt memory region failed (addr=41b00000 size=100000) ERROR: reserving fdt memory region failed (addr=44920000 size=258000) [04.461]Starting kernel ... [04.463]total: 4463 ms [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.61 (lin@server10) (arm-linux-gnueabi-gcc (Linaro GCC 5.3-2016.05) 5.3.1 20160412, GNU ld (Linaro_Binutils-2016.05) 2.25.0 Linaro 2016_02) #2 SMP PREEMPT Thu Oct 9 16:58:59 CST 2025 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: sun8iw20 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Reserved memory: created DMA memory pool at 0x42200000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vdev0buffer@42200000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x42244000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node dsp0_rpbuf@42244000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 8 MiB at 0x47800000 [ 0.000000] On node 0 totalpages: 32420 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32420 pages, LIFO batch:7 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 15 pages/cpu s30912 r8192 d22336 u61440 [ 0.000000] pcpu-alloc: s30912 r8192 d22336 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32164 [ 0.000000] Kernel command line: ubi.mtd=sys ubi.block=0,rootfs earlycon=uart8250,mmio32,0x05000000 clk_ignore_unused initcall_debug=0 console=ttyS3,115200 loglevel=8 root=ubi0_5 rootfstype=ubifs,rw rootwait init=/init partitions=mbr@ubi0_0:boot-resource@ubi0_1:env@ubi0_2:env-redund@ubi0_3:boot@ubi0_4:rootfs@ubi0_5:dsp0@ubi0_6:private@ubi0_7:UDISK@ubi0_8: cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.hardware=sun8iw20p1 boot_type=5 androidboot.boot_type=5 gpt=1 uboot_message=2018.07-gce06dac(03/15/2025-06:33:14) disp_reserve=2457600,0x44920000 aw-ubi-spinand.ubootblks=24 androidboot.dramfreq=792 androidboot.dramsize=128 mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys) uboot_backup=ubootA [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 98456K/129680K available (7168K kernel code, 428K rwdata, 2644K rodata, 1024K init, 177K bss, 23032K reserved, 8192K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x254/0x3d0 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000019] Switching to timer-based delay loop, resolution 41ns [ 0.000209] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000872] Console: colour dummy device 80x30 [ 0.000914] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.000929] pid_max: default: 32768 minimum: 301 [ 0.001081] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001095] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001733] CPU: Testing write buffer coherency: ok [ 0.002095] /cpus/cpu@0 missing clock-frequency property [ 0.002119] /cpus/cpu@1 missing clock-frequency property [ 0.002131] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.002743] Setting up static identity map for 0x40100000 - 0x40100060 [ 0.002869] rcu: Hierarchical SRCU implementation. [ 0.003195] BOOTEVENT: 3.186832: ON [ 0.003399] smp: Bringing up secondary CPUs ... [ 0.004656] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.004811] smp: Brought up 1 node, 2 CPUs [ 0.004825] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.004833] CPU: All CPU(s) started in SVC mode. [ 0.005337] devtmpfs: initialized [ 0.018974] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.019595] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.019625] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.020161] pinctrl core: initialized pinctrl subsystem [ 0.021559] NET: Registered protocol family 16 [ 0.023567] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.059454] rtc_ccu: sunxi ccu init OK [ 0.061845] ccu: sunxi ccu init OK [ 0.062365] r_ccu: sunxi ccu init OK [ 0.103446] sun6i-dma 3002000.dma-controller: sunxi dma probed [ 0.107669] iommu: Default domain type: Translated [ 0.107895] sunxi iommu: irq = 24 [ 0.109023] SCSI subsystem initialized [ 0.109412] usbcore: registered new interface driver usbfs [ 0.109517] usbcore: registered new interface driver hub [ 0.109646] usbcore: registered new device driver usb [ 0.109860] mc: Linux media interface: v0.10 [ 0.109918] videodev: Linux video capture interface: v2.00 [ 0.112034] Advanced Linux Sound Architecture Driver Initialized. [ 0.112705] Bluetooth: Core ver 2.22 [ 0.112780] NET: Registered protocol family 31 [ 0.112790] Bluetooth: HCI device and connection manager initialized [ 0.112810] Bluetooth: HCI socket layer initialized [ 0.112822] Bluetooth: L2CAP socket layer initialized [ 0.112847] Bluetooth: SCO socket layer initialized [ 0.113198] pwm module init! [ 0.120945] g2d 5410000.g2d: Adding to iommu group 0 [ 0.121414] G2D: rcq version initialized.major:250 [ 0.122139] input: sunxi-keyboard as /devices/virtual/input/input0 [ 0.124206] clocksource: Switched to clocksource arch_sys_counter [ 0.133545] sun8iw20-pinctrl pio: initialized sunXi PIO driver [ 0.148779] sunxi udc is no enable [ 0.148938] thermal_sys: Registered thermal governor 'step_wise' [ 0.148942] thermal_sys: Registered thermal governor 'user_space' [ 0.148954] thermal_sys: Registered thermal governor 'power_allocator' [ 0.149528] NET: Registered protocol family 2 [ 0.150306] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.150339] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.150365] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.150388] TCP: Hash tables configured (established 1024 bind 1024) [ 0.150494] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.150530] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.150700] NET: Registered protocol family 1 [ 0.151857] sun8iw20-pinctrl pio: pio supply vcc-pc not found, using dummy regulator [ 0.152381] spi spi0: spi0 supply spi not found, using dummy regulator [ 0.152655] sunxi_spi_resource_get()2480 - sample_mode:2 sample_delay:4 [ 0.152694] sunxi_spi_request_dma()966 - [spi0] Request DMA channel dma0chan0 (tx) and dma0chan1 (rx) for DMA transfers [ 0.152753] sunxi_spi_clk_init()2530 - [spi0] mclk 100000000 [ 0.153457] sunxi_spi_probe()3001 - [spi0]: driver probe succeed, base c881f000, irq 38 [ 0.156158] Initialise system trusted keyrings [ 0.156355] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 0.167666] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.167939] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.168255] fuse: init (API version 7.31) [ 0.197440] NET: Registered protocol family 38 [ 0.197465] Key type asymmetric registered [ 0.197474] Asymmetric key parser 'x509' registered [ 0.197567] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.197581] io scheduler mq-deadline registered [ 0.197591] io scheduler kyber registered [ 0.197718] atomic64_test: passed [ 0.199228] [DISP]disp_module_init [ 0.199885] disp 5000000.disp: Adding to iommu group 0 [ 0.200536] [DISP] disp_init,line:2372: [ 0.200543] smooth display screen:0 type:1 mode:4 [ 0.217596] display_fb_request,fb_id:0 [ 0.225733] disp_al_manager_apply ouput_type:1 [ 0.225903] [DISP] lcd_clk_config,line:777: [ 0.225915] disp 0, clk: pll(364000000),clk(364000000),dclk(52000000) dsi_rate(364000000) [ 0.225915] clk real:pll(360000000),clk(360000000),dclk(51428571) dsi_rate(0) [ 0.226230] sun8iw20-pinctrl pio: pio supply vcc-pd not found, using dummy regulator [ 0.226885] [DISP]disp_module_init finish [ 0.228067] sunxi_sid_init()783 - insmod ok [ 0.228771] pwm-regulator: supplied by regulator-dummy [ 0.230390] sun8iw20-pinctrl pio: pio supply vcc-pb not found, using dummy regulator [ 0.230774] uart uart3: uart3 supply uart not found, using dummy regulator [ 0.231129] uart3: ttyS3 at MMIO 0x2500c00 (irq = 34, base_baud = 1500000) is a SUNXI [ 0.231162] sw_console_setup()1831 - console setup baud 115200 parity n bits 8, flow n [ 0.259131] Freeing logo buffer memory: 2400K [ 1.222498] printk: console [ttyS3] enabled [ 1.228379] misc dump reg init [ 1.232425] deinterlace 5400000.deinterlace: Adding to iommu group 0 [ 1.240127] deinterlace 5400000.deinterlace: version[1.0.0], ip=0x110 [ 1.249990] sunxi-spinand: AW SPINand MTD Layer Version: 2.5 20231129 [ 1.257244] sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.15 20231114 [ 1.265139] sunxi-spinand-phy: not detect any munufacture from id table [ 1.272543] sunxi-spinand-phy: get spi-nand Model from fdt fail [ 1.279191] sunxi-spinand-phy: get phy info from fdt fail [ 1.285241] sunxi-spinand-phy: not detect munufacture from fdt [ 1.291885] sunxi-spinand-phy: detect munufacture from id table: Winbond [ 1.299408] sunxi-spinand-phy: detect spinand id: ff21aaef ffffffff [ 1.306427] sunxi-spinand-phy: ========== arch info ========== [ 1.312949] sunxi-spinand-phy: Model: W25N01GVZEIG [ 1.319678] sunxi-spinand-phy: Munufacture: Winbond [ 1.325919] sunxi-spinand-phy: DieCntPerChip: 1 [ 1.331566] sunxi-spinand-phy: BlkCntPerDie: 1024 [ 1.337511] sunxi-spinand-phy: PageCntPerBlk: 64 [ 1.343255] sunxi-spinand-phy: SectCntPerPage: 4 [ 1.348910] sunxi-spinand-phy: OobSizePerPage: 64 [ 1.354664] sunxi-spinand-phy: BadBlockFlag: 0x0 [ 1.360505] sunxi-spinand-phy: OperationOpt: 0x7 [ 1.366353] sunxi-spinand-phy: MaxEraseTimes: 65000 [ 1.372386] sunxi-spinand-phy: EccFlag: 0x0 [ 1.378244] sunxi-spinand-phy: EccType: 2 [ 1.383890] sunxi-spinand-phy: EccProtectedType: 3 [ 1.389544] sunxi-spinand-phy: ======================================== [ 1.396946] sunxi-spinand-phy: [ 1.400452] sunxi-spinand-phy: ========== physical info ========== [ 1.407370] sunxi-spinand-phy: TotalSize: 128 M [ 1.412725] sunxi-spinand-phy: SectorSize: 512 B [ 1.418094] sunxi-spinand-phy: PageSize: 2 K [ 1.423255] sunxi-spinand-phy: BlockSize: 128 K [ 1.428627] sunxi-spinand-phy: OOBSize: 64 B [ 1.433882] sunxi-spinand-phy: ======================================== [ 1.441290] sunxi-spinand-phy: [ 1.444808] sunxi-spinand-phy: ========== logical info ========== [ 1.451618] sunxi-spinand-phy: TotalSize: 128 M [ 1.456983] sunxi-spinand-phy: SectorSize: 512 B [ 1.462339] sunxi-spinand-phy: PageSize: 4 K [ 1.467509] sunxi-spinand-phy: BlockSize: 256 K [ 1.472861] sunxi-spinand-phy: OOBSize: 128 B [ 1.478232] sunxi-spinand-phy: ======================================== [ 1.485640] sunxi-spinand-phy: W25N01GVZEIG reset rx bit width to 1 [ 1.492646] sunxi-spinand-phy: W25N01GVZEIG reset tx bit width to 1 [ 1.499747] sunxi-spinand-phy: block lock register: 0x00 [ 1.505811] sunxi-spinand-phy: feature register: 0x19 [ 1.511462] sunxi-spinand-phy: sunxi physic nand init end [ 1.518017] Creating 4 MTD partitions on "sunxi_mtd_nand": [ 1.524161] 0x000000000000-0x000000100000 : "boot0" [ 1.535395] 0x000000100000-0x000000400000 : "uboot" [ 1.542331] sunxi-spinand-phy: phy blk 20 is bad [ 1.555316] 0x000000400000-0x000000500000 : "secure_storage" [ 1.561830] sunxi-spinand-phy: ecc error 0x2 [ 1.566804] sunxi-spinand-phy: ecc error 0x2 [ 1.575354] 0x000000500000-0x000008000000 : "sys" [ 1.580942] random: fast init done [ 1.654482] sunxi-spinand-phy: phy blk 675 is bad [ 1.660629] sunxi-spinand-phy: phy blk 683 is bad [ 1.671558] sunxi-spinand-phy: phy blk 735 is bad [ 1.678387] sunxi-spinand-phy: phy blk 749 is bad [ 1.700743] sunxi-spinand-phy: phy blk 897 is bad [ 1.709547] sunxi-spinand-phy: phy blk 929 is bad [ 1.736034] libphy: Fixed MDIO Bus: probed [ 1.740628] CAN device driver interface [ 1.745642] usbcore: registered new interface driver asix [ 1.751771] usbcore: registered new interface driver ax88179_178a [ 1.758760] usbcore: registered new interface driver cdc_ether [ 1.765382] usbcore: registered new interface driver net1080 [ 1.771776] usbcore: registered new interface driver cdc_subset [ 1.778505] usbcore: registered new interface driver zaurus [ 1.784867] usbcore: registered new interface driver cdc_ncm [ 1.791235] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.798556] sunxi-ehci: EHCI SUNXI driver [ 1.803445] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.810439] sunxi-ohci: OHCI SUNXI driver [ 1.815565] usbcore: registered new interface driver uas [ 1.821594] usbcore: registered new interface driver usb-storage [ 1.828446] usbcore: registered new interface driver ums-alauda [ 1.835189] usbcore: registered new interface driver ums-cypress [ 1.842007] usbcore: registered new interface driver ums-datafab [ 1.848818] usbcore: registered new interface driver ums_eneub6250 [ 1.855813] usbcore: registered new interface driver ums-freecom [ 1.862607] usbcore: registered new interface driver ums-isd200 [ 1.869310] usbcore: registered new interface driver ums-jumpshot [ 1.876223] usbcore: registered new interface driver ums-karma [ 1.882804] usbcore: registered new interface driver ums-onetouch [ 1.889722] usbcore: registered new interface driver ums-realtek [ 1.896541] usbcore: registered new interface driver ums-sddr09 [ 1.903222] usbcore: registered new interface driver ums-sddr55 [ 1.909966] usbcore: registered new interface driver ums-usbat [ 1.916671] usbcore: registered new interface driver option [ 1.922953] usbserial: USB Serial support registered for GSM modem (1-port) [ 1.931836] input: sunxi-ts as /devices/platform/soc@3000000/2009c00.rtp/input/input1 [ 1.941388] sunxi_gpadc_init,2228, success [ 1.946664] sunxi_gpadc_setup: get channel scan data failed [ 1.953159] input: sunxi-gpadc0 as /devices/virtual/input/input2 [ 1.961309] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 1.972076] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 1.983431] sunxi-rtc 7090000.rtc: registered as rtc0 [ 1.989177] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 1.999858] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T01:58:26 UTC (7106) [ 2.009052] sunxi-rtc 7090000.rtc: Fail to read dts property 'gpr_bootcount_pos' [ 2.017370] reasonbase NULL [ 2.020496] reason large than max, fix to hot reboot, save boot reason [ 2.027827] invalid reason or reasonbase NULL [ 2.032713] sunxi-rtc 7090000.rtc: sunxi rtc probed [ 2.038695] i2c /dev entries driver [ 2.042861] IR NEC protocol handler initialized [ 2.047972] IR RC5(x/sz) protocol handler initialized [ 2.054294] [VIN_WARN]sensor_helper_probe: cannot get sensor0_cameravdd supply, setting it to NULL! [ 2.064478] [VIN_WARN]sensor_helper_probe: cannot get sensor0_iovdd supply, setting it to NULL! [ 2.074278] [VIN_WARN]sensor_helper_probe: cannot get sensor0_avdd supply, setting it to NULL! [ 2.083937] [VIN_WARN]sensor_helper_probe: cannot get sensor0_dvdd supply, setting it to NULL! [ 2.095819] usbcore: registered new interface driver uvcvideo [ 2.102272] USB Video Class driver (1.1.1) [ 2.106898] gspca_main: v2.14.0 registered [ 2.111505] sunxi cedar version 1.1 [ 2.116775] sunxi-wdt 20500a0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 2.126006] Bluetooth: HCI UART driver ver 2.3 [ 2.130987] Bluetooth: HCI UART protocol H4 registered [ 2.137066] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10 [ 2.146702] usbcore: registered new interface driver usbhid [ 2.152954] usbhid: USB HID core driver [ 2.157276] exFAT: Version 1.3.0 [ 2.161727] rpmsg_tty_init: Sunxi rpmsg tty driver will init [ 2.168161] rpmsg_tty_init: Sunxi rpmsg tty driver init ok [ 2.178134] NET: Registered protocol family 10 [ 2.184093] Segment Routing with IPv6 [ 2.188316] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.196662] NET: Registered protocol family 17 [ 2.201676] NET: Registered protocol family 15 [ 2.206699] can: controller area network core (rev 20170425 abi 9) [ 2.213735] NET: Registered protocol family 29 [ 2.218748] can: raw protocol (rev 20170425) [ 2.223529] can: broadcast manager protocol (rev 20170425 t) [ 2.229903] can: netlink gateway (rev 20190810) max_hops=1 [ 2.236523] Bluetooth: RFCOMM TTY layer initialized [ 2.242030] Bluetooth: RFCOMM socket layer initialized [ 2.247844] Bluetooth: RFCOMM ver 1.11 [ 2.252933] Registering SWP/SWPB emulation handler [ 2.258793] Loading compiled-in X.509 certificates [ 2.285307] sunxi udc is no enable [ 2.290445] sunxi-thermal 2009400.ths: sun8iw20 chip id: 24576 [ 2.297062] sunxi-thermal 2009400.ths: sun8iw20 t1: 8000 [ 2.303141] sunxi-thermal 2009400.ths: sun8iw20 cp version:21 [ 2.355217] get drvvbus-en is fail, 22 [ 2.359464] get ehci0-controller wakeup-source is fail. [ 2.365412] sunxi ehci0-controller is no enable [ 2.370507] sunxi-ehci 4101000.ehci0-controller: init_sunxi_hci is fail [ 2.378002] sunxi-ehci: probe of 4101000.ehci0-controller failed with error -1 [ 2.386488] get drvvbus-en is fail, 22 [ 2.390711] get ohci0-controller wakeup-source is fail. [ 2.396608] sunxi ohci0-controller is no enable [ 2.401697] sunxi-ohci 4101400.ohci0-controller: init_sunxi_hci is fail [ 2.409176] sunxi-ohci: probe of 4101400.ohci0-controller failed with error -1 [ 2.417618] get drvvbus-en is fail, 22 [ 2.421836] get ehci1-controller wakeup-source is fail. [ 2.427735] sunxi ehci1-controller is no enable [ 2.432826] sunxi-ehci 4200000.ehci1-controller: init_sunxi_hci is fail [ 2.440290] sunxi-ehci: probe of 4200000.ehci1-controller failed with error -1 [ 2.448726] get drvvbus-en is fail, 22 [ 2.452942] get ohci1-controller wakeup-source is fail. [ 2.458847] sunxi ohci1-controller is no enable [ 2.463938] sunxi-ohci 4200400.ohci1-controller: init_sunxi_hci is fail [ 2.471405] sunxi-ohci: probe of 4200400.ohci1-controller failed with error -1 [ 2.480035] ubi0: attaching mtd3 [ 2.792322] ubi0: scanning is finished [ 2.796600] ubi0 error: ubi_read_volume_table: the layout volume was not found [ 2.804961] ubi0 error: ubi_attach_mtd_dev: failed to attach mtd3, error -22 [ 2.812948] UBI error: cannot attach mtd3 [ 2.817520] UBI: block: can't open volume on ubi0_-1, err=-19 [ 2.825398] sun8iw20-pinctrl pio: pio supply vcc-pe not found, using dummy regulator [ 2.834422] vin_csi 5801000.csi: Adding to iommu group 0 [ 2.843179] sunxi-vin-core 5809000.vinc: Adding to iommu group 0 [ 2.850350] sunxi-vin-core 5809200.vinc: Adding to iommu group 0 [ 2.858408] [VIN_WARN]get csi isp clk fail [ 2.863022] [VIN_WARN]get csi isp src clk fail [ 2.868103] [VIN_WARN]get csi mipi clk fail [ 2.872805] [VIN_WARN]get csi mipi src clk fail [ 2.877955] [VIN_WARN]get csi isp mbus clk fail [ 2.883067] [VIN_WARN]Get isp reset control fail [ 2.888492] [VIN_ERR]n5 request i2c3 adapter failed! [ 2.899615] debugfs: Directory 'soc@3000000:codec_plat' with parent 'audiocodec' already present! [ 2.910284] sunxi-snd-mach soc@3000000:codec_mach: 2030000.codec <-> soc@3000000:codec_plat mapping ok [ 2.922007] input: audiocodec Headphones as /devices/platform/soc@3000000/soc@3000000:codec_mach/sound/card0/input3 [ 2.934685] [sound 403][MACH simple_parse_of] simple_dai_link_of failed [ 2.942358] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 2.953670] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 2.961197] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 2.964254] clk: Not disabling unused clocks [ 2.970897] cfg80211: failed to load regulatory.db [ 2.975744] ALSA device list: [ 2.984477] #0: audiocodec [ 2.987722] alloc_fd: slot 0 not NULL! [ 2.992318] VFS: Cannot open root device "ubi0_5" or unknown-block(0,0): error -19 [ 3.000849] Please append a correct "root=" boot option; here are the available partitions: [ 3.010258] 1f00 1024 mtdblock0 [ 3.010261] (driver?) [ 3.017620] 1f01 3072 mtdblock1 [ 3.017622] (driver?) [ 3.025052] 1f02 1024 mtdblock2 [ 3.025055] (driver?) [ 3.032397] 1f03 125952 mtdblock3 [ 3.032400] (driver?) [ 3.039763] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 3.049035] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.61 #2 [ 3.055671] Hardware name: Generic DT based system [ 3.061063] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [ 3.069757] [] (show_stack) from [] (dump_stack+0x7c/0x98) [ 3.077863] [] (dump_stack) from [] (panic+0x100/0x3d4) [ 3.085679] [] (panic) from [] (mount_block_root+0x288/0x334) [ 3.094078] [] (mount_block_root) from [] (prepare_namespace+0x84/0x178) [ 3.103550] [] (prepare_namespace) from [] (kernel_init+0x8/0x118) [ 3.112435] [] (kernel_init) from [] (ret_from_fork+0x14/0x2c) [ 3.120926] Exception stack(0xc7025fb0 to 0xc7025ff8) [ 3.126591] 5fa0: 00000000 00000000 00000000 00000000 [ 3.135766] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 3.144936] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 3.152360] CPU1: stopping [ 3.155395] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.4.61 #2 [ 3.162030] Hardware name: Generic DT based system [ 3.167409] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [ 3.176096] [] (show_stack) from [] (dump_stack+0x7c/0x98) [ 3.184199] [] (dump_stack) from [] (handle_IPI+0xc0/0x168) [ 3.192405] [] (handle_IPI) from [] (gic_handle_irq+0x70/0x78) [ 3.200902] [] (gic_handle_irq) from [] (__irq_svc+0x6c/0xa8) [ 3.209293] Exception stack(0xc7065f80 to 0xc7065fc8) [ 3.214961] 5f80: 000079e0 c76c4534 00000000 c0114e40 00000002 c7064000 c0c03de4 c0c03e20 [ 3.224134] 5fa0: 4000406a 410fc075 00000000 00000000 c0c768b0 c7065fd0 c0108040 c0108044 [ 3.233301] 5fc0: 60000113 ffffffff [ 3.237218] [] (__irq_svc) from [] (arch_cpu_idle+0x2c/0x38) [ 3.245520] [] (arch_cpu_idle) from [] (do_idle+0xb8/0x120) [ 3.253723] [] (do_idle) from [] (cpu_startup_entry+0x18/0x1c) [ 3.262217] [] (cpu_startup_entry) from [<40102c0c>] (0x40102c0c) [ 3.270025] invalid reason or reasonbase NULL [ 3.274920] rtc set bootreason panic reboot fail [ 3.280114] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---