已经有按照tina的文档，修改sys_config.fex，make menuconfig，make kernel_menuconfig。

环境是：
SPINAN型号：W25N01G
tina3.5
u-boot-2014.07
linux-3.10

以下是烧录的时候，日志的头尾两端。

[0]beign to init dram
[23]init dram ok


U-Boot 2014.07 (Jul 31 2018 - 14:59:19) Allwinner Technology

uboot commit : 6604446f7bddb8fe53f2b993100929f92a5f4d6e

i2c_init: by cpux
[I2C-DEBUG]:i2c_set_clock() 354
[I2C-ERROR]:twi_send_clk_9pulse() 136 SDA is still Stuck Low, failed.
i2c_init ok
[2.642]pmbus:   ready
axp: get node[/soc/pmu0] error
axp_probe error
[2.649]PMU: cpux 408 Mhz,AXI=408 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz
DRAM:  32 MiB
[2.658]fdt addr: 0x809e77a0
[2.660]gd->fdt_size: 0xc360
Relocation Offset is: 01524000
axp: get node[/soc/pmu0] error
int sunxi_dma_init---
irq enable
[2.730]flash init start
workmode = 16,storage type = 3
try card 1
[2.736][mmc]: mmc driver ver 2018-6-1 17:39:00
SUNXI SD/MMC: 1
[2.753][mmc]: ************Try SD card 1************
[mmc]: mmc 1 cmd 8 timeout, err 100
[mmc]: smc 1 err, cmd 8,  RTO
[mmc]: mmc 1 close bus gating and reset
[mmc]: mmc 1 mmc cmd 8 err 0x00000100
[2.771][mmc]: mmc send if cond failed
[mmc]: mmc 1 cmd 55 timeout, err 100
[mmc]: smc 1 err, cmd 55,  RTO
[mmc]: mmc 1 close bus gating and reset
[mmc]: mmc 1 mmc cmd 55 err 0x00000100
[2.789][mmc]: send app cmd failed
[2.792][mmc]: ************Try MMC card 1************
[mmc]: mmc 1 cmd 1 timeout, err 100
[mmc]: smc 1 err, cmd 1,  RTO
[mmc]: mmc 1 close bus gating and reset
[mmc]: mmc 1 mmc cmd 1 err 0x00000100
[2.814][mmc]: read op condition failed
[2.817][mmc]: mmc send op cond failed
Card did not respond to voltage select!
[2.824][mmc]: ************SD/MMC 1 init error!!!************
[2.830][mmc]: mmc_init_boot: mmc int fail
[2.833][mmc]: mmc_init: mmc init fail, err -17
MMC init failed
try emmc fail
[2.840]NAND_UbootProbe start...
[2.843]NB1 : enter phy init
[2.846]nand_physic_init
[2.850]nand0: get node offset error
[2.853]init nctri NAND PIORequest error!
[2.857]nand_physic_init, init nctri error
[2.861]nand_physic_init init_parameter error
[2.865]nand_physic_init error -1
[2.868]SpiNandHwInit: Start Nand Hardware initializing Jun  9 2018 19:05:34.....
[2.875]uboot: nand version: 3 6008 20180610 1300
[2.892]request spi gpio  ok!
int sunxi_dma_init---
irq enable
[2.897]uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x81db8c7c
[2.905]request general tx dma channel ok!
[2.908]uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x81db8c9c
[2.916]request general rx dma channel ok!
[2.920]SPI nand ID: 21aaef 0
[2.922][SCAN_DBG] NandTwoPlaneOp: 1, DriverTwoPlaneOPCfg: 1, 0xffbfffff
[2.929]nand : get id number_ctl from script:0x55aaaa55
[2.934]_UpdateExtAccessFreqPara: no para.
[2.938]PHY_Scan_DelayMode: right delay mode 0x0
[2.942]PHY_Scan_DelayMode: right delay mode 0x800
_get_spic_clk_v1: sclk0=0x64
[2.949]PHY_Scan_DelayMode: right delay mode,clk 50 MHz, SPI_TCR = 0x00000984, bit[13]=0,bit[11]=1
[2.958]physic_info_read start!!
[2.961]physic_info_get_offset start!!
[2.966]physic_info_get_one_copy start!!
[2.970]block 13 page 48
[2.972]block 13 page 49
[2.974]block 13 page 50
[2.977]block 13 page 51
[2.979]block 13 page 52
[2.981]block 13 page 53
[2.983]block 13 page 54
[2.986]block 13 page 55
[2.988]block 13 page 56
[2.990]block 13 page 57
[2.992]block 13 page 58
[2.994]block 13 page 59
[2.997]block 13 page 60
[2.999]block 13 page 61
[3.001]block 13 page 62
[3.003]block 13 page 63
[3.006]physic info copy is ok
[3.009]

[3.010][SCAN_DBG] ==============Nand Architecture Parameter==============
[3.016][SCAN_DBG]    Nand Chip ID:         0xff21aaef 0xffffffff
[3.022][SCAN_DBG]    Nand Chip Count:      0x1
[3.026][SCAN_DBG]    Nand Chip Connect:    0x1
[3.030][SCAN_DBG]    Sector Count Of Page: 0x4
[3.035][SCAN_DBG]    Page Count Of Block:  0x40
[3.039][SCAN_DBG]    Block Count Of Die:   0x400
[3.043][SCAN_DBG]    Plane Count Of Die:   0x1
[3.048][SCAN_DBG]    Die Count Of Chip:    0x1
[3.052][SCAN_DBG]    Bank Count Of Chip:   0x1
[3.056][SCAN_DBG]    Optional Operation:   0x60
[3.060][SCAN_DBG]    Access Frequence:     0x0
[3.065][SCAN_DBG] =======================================================

[3.092]secure storage updata ok!
[3.095]nand secure storage ok: 58,59
[3.099]NB1 : nand phy init ok
[3.101]NB1 : enter phy Exit
nand release dma:81db8c7c
nand release dma:0
sunxi dma exit
[3.109]NAND_UbootProbe end: 0x0
nand found
read mbr copy[0] failed
read mbr copy[1] failed
read mbr copy[2] failed
read mbr copy[3] failed
[3.122]flash init end
[3.124]try to burn key
[3.129]inter uboot shell
Hit any key to stop autoboot:  0
work mode=0x10
run usb efex
delay time 2500
int sunxi_dma_init---
irq enable
sunxi_dma_install_int ok
usb init ok
set address 0xd
set address 0xd
SUNXI_EFEX_ERASE_TAG
erase_flag = 0x0
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
the 0 mbr table is ok
the 1 mbr table is ok
the 2 mbr table is ok
the 3 mbr table is ok
*************MBR DUMP***************
total mbr part 8

part[0] name      :bootlogo
part[0] classname :DISK
part[0] addrlo    :0x2000
part[0] lenlo     :0x800
part[0] user_type :32768
part[0] keydata   :0
part[0] ro        :0

part[1] name      :env
part[1] classname :DISK
part[1] addrlo    :0x2800
part[1] lenlo     :0x200
part[1] user_type :32768
part[1] keydata   :0
part[1] ro        :0

part[2] name      :boot
part[2] classname :DISK
part[2] addrlo    :0x2a00
part[2] lenlo     :0x3000
part[2] user_type :32768
part[2] keydata   :0
part[2] ro        :0

part[3] name      :rootfs
part[3] classname :DISK
part[3] addrlo    :0x5a00
part[3] lenlo     :0x15c70
part[3] user_type :32768
part[3] keydata   :0
part[3] ro        :0

part[4] name      :rootfs_data
part[4] classname :DISK
part[4] addrlo    :0x1b670
part[4] lenlo     :0xc800
part[4] user_type :32768
part[4] keydata   :0
part[4] ro        :0

part[5] name      :misc
part[5] classname :DISK
part[5] addrlo    :0x27e70
part[5] lenlo     :0x200
part[5] user_type :32768
part[5] keydata   :0
part[5] ro        :0

part[6] name      :private
part[6] classname :DISK
part[6] addrlo    :0x28070
part[6] lenlo     :0x200
part[6] user_type :32768
part[6] keydata   :0
part[6] ro        :0

part[7] name      :UDISK
part[7] classname :DISK
part[7] addrlo    :0x28270
part[7] lenlo     :0x0
part[7] user_type :33024
part[7] keydata   :0
part[7] ro        :0

total part: 9
mbr 0, 2000, 8000
bootlogo 1, 800, 8000
env 2, 200, 8000
boot 3, 3000, 8000
rootfs 4, 15c70, 8000
rootfs_data 5, c800, 8000
misc 6, 200, 8000
private 7, 200, 8000
UDISK 8, 0, 8100
[7.326]erase_flag = 0
[7.328]NB1 : enter phy init
[7.330]SpiNandHwInit: Start Nand Hardware initializing Jun  9 2018 19:05:34.....
[7.337]uboot: nand version: 3 6008 20180610 1300
[7.354]request spi gpio  ok!
[7.357]uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x81db8c9c
[7.364]request general tx dma channel ok!
[7.368]uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x81db8cbc
[7.375]request general rx dma channel ok!
[7.379]SPI nand ID: 21aaef 0
[7.382][SCAN_DBG] NandTwoPlaneOp: 1, DriverTwoPlaneOPCfg: 1, 0xffbfffff
[7.388]nand : get id number_ctl from script:0x55aaaa55
[7.393]_UpdateExtAccessFreqPara: no para.
[7.397]PHY_Scan_DelayMode: right delay mode 0x0
[7.402]PHY_Scan_DelayMode: right delay mode 0x800
_get_spic_clk_v1: sclk0=0x64
[7.409]PHY_Scan_DelayMode: right delay mode,clk 50 MHz, SPI_TCR = 0x00000984, bit[13]=0,bit[11]=1
[7.417]physic_info_read start!!
[7.420]physic_info_read already!!
[7.423]

[7.424][SCAN_DBG] ==============Nand Architecture Parameter==============
[7.431][SCAN_DBG]    Nand Chip ID:         0xff21aaef 0xffffffff
[7.437][SCAN_DBG]    Nand Chip Count:      0x1
[7.441][SCAN_DBG]    Nand Chip Connect:    0x1
[7.445][SCAN_DBG]    Sector Count Of Page: 0x4
[7.449][SCAN_DBG]    Page Count Of Block:  0x40
[7.454][SCAN_DBG]    Block Count Of Die:   0x400
[7.458][SCAN_DBG]    Plane Count Of Die:   0x1
[7.462][SCAN_DBG]    Die Count Of Chip:    0x1
[7.466][SCAN_DBG]    Bank Count Of Chip:   0x1
[7.471][SCAN_DBG]    Optional Operation:   0x60
[7.475][SCAN_DBG]    Access Frequence:     0x0
[7.479][SCAN_DBG] =======================================================

[7.507]secure storage updata ok!
[7.510]nand secure storage ok: 58,59
[7.513]NB1 : nand phy init ok
[7.516]uboot_start_block 8 uboot_next_block 58.
[7.520]check nand version start.
[7.523]Current nand driver version is ff 0 3 1
[7.528]Media version is valid in block 8, version info is ff 0 3 1
[7.534]nand driver version match ok in block 8.
[7.538]nand version = 0
[7.540]has cleared the boot blocks.
[7.548]NAND_Uboot_Erase
[7.550]NB1 : enter phy Exit
nand release dma:81db8c9c
nand release dma:0
not need erase flash
sunxi_sprite_erase_flash, erase_flag=0
private part exist
NAND_UbootInit
[7.565]NAND_UbootInit start
[7.567]NB1: enter NAND_LogicInit
[7.570]SpiNandHwInit: Start Nand Hardware initializing Jun  9 2018 19:05:34.....
[7.578]uboot: nand version: 3 6008 20180610 1300
[7.594]uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x81db8c9c
[7.602]uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x81db8cbc
_get_spic_clk_v1: sclk0=0x64
[7.633]not burn nand partition table!
[7.637][ND]not enough block:479,878!!
[7.640][NE]build phy partition 0 error!
[7.644][NE]build all phy partition fail!
[7.764][NE]not find mbr table!!!!
[7.767]NB1: nand_info_init fail
[7.770]NAND_UbootInit end: 0xfffffffb
NAND_UbootExit

[19.204]PHY_PageReadSpare bad flag: bank 0x0  block 0x3f8  page 0x0
[19.210][PHY_DBG] Find a bad block (NO. 0x3f8) in the Die 0x0
[19.216]PHY_PageReadSpare bad flag: bank 0x0  block 0x3f9  page 0x0
[19.222][PHY_DBG] Find a bad block (NO. 0x3f9) in the Die 0x0
[19.227]PHY_PageReadSpare bad flag: bank 0x0  block 0x3fa  page 0x0
[19.233][PHY_DBG] Find a bad block (NO. 0x3fa) in the Die 0x0
[19.239]PHY_PageReadSpare bad flag: bank 0x0  block 0x3fb  page 0x0
[19.245][PHY_DBG] Find a bad block (NO. 0x3fb) in the Die 0x0
[19.251]PHY_PageReadSpare bad flag: bank 0x0  block 0x3fc  page 0x0
[19.257][PHY_DBG] Find a bad block (NO. 0x3fc) in the Die 0x0
[19.262]PHY_PageReadSpare bad flag: bank 0x0  block 0x3fd  page 0x0
[19.268][PHY_DBG] Find a bad block (NO. 0x3fd) in the Die 0x0
[19.274]PHY_PageReadSpare bad flag: bank 0x0  block 0x3fe  page 0x0
[19.280][PHY_DBG] Find a bad block (NO. 0x3fe) in the Die 0x0
[19.286]PHY_PageReadSpare bad flag: bank 0x0  block 0x3ff  page 0x0
[19.292][PHY_DBG] Find a bad block (NO. 0x3ff) in the Die 0x0
[19.297][NE]not find mbr table!!!!
[19.301]NB1: nand_info_init fail
[19.304]NAND_UbootInit end: 0xfffffffb
sunxi sprite init fail when downlaod mbr