<![CDATA[t113的emmc启动，挂载文件系统失败]]>[104]HELLO! BOOT0 is starting! [107]BOOT0 commit : adaf1174cc [110]set pll start [112]fix vccio detect value:0xc0 [119]periph0 has been enabled [122]set pll end [124][pmu]: bus read error [127]board init ok [129]ZQ value = 0x30 [131]get_pmu_exist() = -1 [133]DRAM BOOT DRIVE INFO: V0.33 [136]DRAM CLK = 936 MHz [139]DRAM Type = 3 (2:DDR2,3:DDR3) [142]DRAMC read ODT off. [144]DRAM ODT value: 0x42. [147]ddr_efuse_type: 0xa [150]DRAM SIZE =128 M [153]dram_tpr4:0x0 [154]PLL_DDR_CTRL_REG:0xf8004d00 [158]DRAM_CLK_REG:0xc0000000 [160][TIMING DEBUG] MR2= 0x20 [168]DRAM simple test OK. [171]rtc standby flag is 0x0, super standby flag is 0x0 [176]dram size =128 [179]card no is 2 [180]sdcard 2 line count 4 [183][mmc]: mmc driver ver 2021-05-21 14:47 [192][mmc]: Wrong media type 0x0, but host sdc2, try mmc first [198][mmc]: ***Try MMC card 2*** [222][mmc]: RMCA OK! [224][mmc]: mmc 2 bias 0 [227][mmc]: MMC 5.1 [229][mmc]: HSSDR52/SDR25 4 bit [232][mmc]: 50000000 Hz [234][mmc]: 7456 MB [236][mmc]: ***SD/MMC 2 init OK!!!*** [326]Loading boot-pkg Succeed(index=0). [329]Entry_name = u-boot [336]Entry_name = optee [340]Entry_name = dtb [343]tunning data addr:0x430003e8 [346]Jump to second Boot. M/TC: OP-TEE version: 6aef7bb2-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Fri Jul 23 09:25:11 UTC 2021 arm U-Boot 2018.05 (Jun 08 2023 - 13:44:46 +0800) Allwinner Technology [00.398]CPU: Allwinner Family [00.401]Model: sun8iw20 [00.403]DRAM: 128 MiB [00.407]Relocation Offset is: 04ebc000 [00.432]secure enable bit: 0 [00.435]smc_tee_inform_fdt failed with: -65526[00.439]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz [00.445]gic: sec monitor mode [00.448]flash init start [00.450]workmode = 0,storage type = 2 [00.453][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00 [00.460][mmc]: SUNXI SDMMC Controller Version:0x50310 [00.485][mmc]: Best spd md: 2-HSDDR52/DDR50, freq: 2-50000000, Bus width: 4 [00.491]sunxi flash init ok [00.494]line:703 init_clocks [00.497]drv_disp_init request pwm success, pwm7:pwm7:0x2000c00. fdt get node offset faill: hdmi [00.513]unable to map hdmi registers [00.516]drv_disp_init finish [00.522]Loading Environment from SUNXI_FLASH... OK [00.535]boot_gui_init:start [00.538]set disp.dev2_output_type fail. using defval=0 [00.545]boot_gui_init:finish partno erro : can't find partition bootloader 54 bytes read in 0 ms [00.554]bmp_name=bootlogo.bmp size 38454 38454 bytes read in 1 ms (36.7 MiB/s) [00.577]Item0 (Map) magic is bad [00.580]the secure storage item0 copy0 magic is bad [00.596]Item0 (Map) magic is bad [00.599]the secure storage item0 copy1 magic is bad [00.603]Item0 (Map) magic is bad [00.606]out of usb burn from boot: not need burn key List file under ULI/factory ** Unrecognized filesystem type ** root_partition is rootfs set root to /dev/mmcblk0p5 [00.621]update part info [00.624]update bootcmd [00.627]change working_fdt 0x43e7be70 to 0x43e5be70 [00.632][mmc]: no mmc-hs400-1_8v! [00.635][mmc]: delete mmc-hs200-1_8v from dtb [00.639][mmc]: get max-frequency ok 50000000 Hz disable nand error: FDT_ERR_BADPATH [00.658]update dts Hit any key to stop autoboot: 1 FDT ERROR:get muxsel err returned FDT_ERR_INTERNAL sunxi_pwm_pin_set_state, fdt_set_all_pin, ret=-1 [00.734]LCD open finish 0 [01.754]no vendor_boot partition is found Android's image name: t113-mq_r [01.766]Starting kernel ... [01.769][mmc]: mmc exit start [01.788][mmc]: mmc 2 exit ok [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.61 (root@luke) (arm-openwrt-linux-muslgnueabi-gcc.bin (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) 6.4.1, GNU ld (GNU Binutils) 2.27) #53 SMP PREEMPT Thu Jun 15 06:12:40 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: sun8iw20 [ 0.000000] printk: bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 4 MiB at 0x47c00000 [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 15 pages/cpu s30348 r8192 d22900 u61440 [ 0.000000] pcpu-alloc: s30348 r8192 d22900 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500400 clk_ignore_unused initcall_debug=0 console=ttyS1,115200 rootdelay=2 loglevel=8 root=/dev/mmcblk0p5 init=/pseudo_init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:private@mmcblk0p6:rootfs_data@mmcblk0p7:UDISK@mmcblk0p8 cma=4M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun8iw20p1 boot_type=2 androidboot.boot_type=2 gpt=1 uboot_message=2018.05(06/08/2023-13:44:46) mbr_offset=1032192 disp_reserve=1536000,0x43f06000 androidboot.dramsize=128 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 106052K/131072K available (6144K kernel code, 306K rwdata, 1536K rodata, 1024K init, 1168K bss, 20924K reserved, 4096K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x26c/0x3ec with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.008017] Switching to timer-based delay loop, resolution 41ns [ 0.014204] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.023914] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.034270] pid_max: default: 32768 minimum: 301 [ 0.039021] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.046346] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.054669] CPU: Testing write buffer coherency: ok [ 0.059891] /cpus/cpu@0 missing clock-frequency property [ 0.065207] /cpus/cpu@1 missing clock-frequency property [ 0.070540] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.076709] Setting up static identity map for 0x40100000 - 0x40100060 [ 0.083372] rcu: Hierarchical SRCU implementation. [ 0.088579] smp: Bringing up secondary CPUs ... [ 0.094221] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.094337] smp: Brought up 1 node, 2 CPUs [ 0.104150] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.110328] CPU: All CPU(s) started in SVC mode. [ 0.115390] devtmpfs: initialized [ 0.130024] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.138160] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.148251] pinctrl core: initialized pinctrl subsystem [ 0.154395] NET: Registered protocol family 16 [ 0.160364] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.198197] rtc_ccu: sunxi ccu init OK [ 0.204443] ccu: sunxi ccu init OK [ 0.208275] r_ccu: sunxi ccu init OK [ 0.231656] iommu: Default domain type: Translated [ 0.236690] sunxi iommu: irq = 24 [ 0.240916] SCSI subsystem initialized [ 0.244920] usbcore: registered new interface driver usbfs [ 0.250483] usbcore: registered new interface driver hub [ 0.255898] usbcore: registered new device driver usb [ 0.261681] Advanced Linux Sound Architecture Driver Initialized. [ 0.268536] Bluetooth: Core ver 2.22 [ 0.272178] NET: Registered protocol family 31 [ 0.276631] Bluetooth: HCI device and connection manager initialized [ 0.283048] Bluetooth: HCI socket layer initialized [ 0.287930] Bluetooth: L2CAP socket layer initialized [ 0.293005] Bluetooth: SCO socket layer initialized [ 0.298119] pwm module init! [ 0.302272] g2d 5410000.g2d: Adding to iommu group 0 [ 0.307557] G2D: rcq version initialized.major:252 [ 0.313204] clocksource: Switched to clocksource arch_sys_counter [ 0.327784] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver [ 0.337108] NET: Registered protocol family 2 [ 0.342015] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.350429] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.358127] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.365215] TCP: Hash tables configured (established 1024 bind 1024) [ 0.371663] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.378235] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.385450] NET: Registered protocol family 1 [ 0.390787] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator [ 0.401115] spi spi0: spi0 supply spi not found, using dummy regulator [ 0.407838] sunxi_spi_resource_get()2116 - [spi0] SPI MASTER MODE [ 0.413994] sunxi_spi_resource_get()2154 - Failed to get sample mode [ 0.420365] sunxi_spi_resource_get()2159 - Failed to get sample delay [ 0.426829] sunxi_spi_resource_get()2163 - sample_mode:-1431633921 sample_delay:-1431633921 [ 0.435265] sunxi_spi_clk_init()2205 - [spi0] mclk 100000000 [ 0.441532] sunxi_spi_probe()2623 - [spi0]: driver probe succeed, base c881f000, irq 45 [ 0.451204] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 0.462641] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.468681] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.501946] io scheduler mq-deadline registered [ 0.506520] io scheduler kyber registered [ 0.511570] [DISP]disp_module_init [ 0.515549] disp 5000000.disp: Adding to iommu group 0 [ 0.521189] [DISP] parser_disp_init_para,line:1430: [ 0.521192] of_property_read fb0_width fail [ 0.530292] [DISP] disp_init,line:2386: [ 0.530295] smooth display screen:0 type:1 mode:4 [ 0.539454] display_fb_request,fb_id:0 [ 0.543240] [DISP] display_fb_request,line:2003: [ 0.543245] invalid paras xres(0), yres(0) bpp(32) [ 0.552971] disp_al_manager_apply ouput_type:1 [ 0.557540] [DISP] lcd_clk_config,line:744: [ 0.557550] disp 0, clk: pll(0),clk(0),dclk(0) dsi_rate(0) [ 0.557550] clk real:pll(297000000),clk(288000000),dclk(0) dsi_rate(0) [ 0.563495] [DISP]disp_module_init finish [ 0.579289] sunxi_sid_init()551 - insmod ok [ 0.584503] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator [ 0.594748] uart uart1: uart1 supply uart not found, using dummy regulator [ 0.601872] uart1: ttyS1 at MMIO 0x2500400 (irq = 34, base_baud = 1500000) is a SUNXI [ 0.609752] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n ▒[ 0.617742] printk: console [ttyS1] enabled [ 0.617742] printk: console [ttyS1] enabled [ 0.626670] printk: bootconsole [earlycon0] disabled [ 0.626670] printk: bootconsole [earlycon0] disabled [ 0.637731] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator [ 0.649090] uart uart2: uart2 supply uart not found, using dummy regulator [ 0.657044] uart2: ttyS2 at MMIO 0x2500800 (irq = 35, base_baud = 1500000) is a SUNXI [ 0.666420] uart uart3: uart3 supply uart not found, using dummy regulator [ 0.674395] uart3: ttyS3 at MMIO 0x2500c00 (irq = 36, base_baud = 1500000) is a SUNXI [ 0.683749] uart uart4: uart4 supply uart not found, using dummy regulator [ 0.691711] uart4: ttyS4 at MMIO 0x2501000 (irq = 37, base_baud = 1500000) is a SUNXI [ 0.701077] uart uart5: uart5 supply uart not found, using dummy regulator [ 0.709082] uart5: ttyS5 at MMIO 0x2501400 (irq = 38, base_baud = 1500000) is a SUNXI [ 0.718667] misc dump reg init [ 0.723233] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9 [ 0.730459] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed [ 0.737795] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed [ 0.745228] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1) [ 0.751749] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power. [ 0.758695] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1) [ 0.766404] sunxi-rfkill soc@3000000:rfkill@0: get gpio wlan_regon failed [ 0.774047] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1 [ 0.782146] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled [ 0.789770] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power. [ 0.796542] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1) [ 0.804067] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=207 assert=0 [ 0.812032] [ADDR_MGT] addr_mgt_probe: module version: v1.0.11 [ 0.819203] [ADDR_MGT] addr_mgt_probe: success. [ 0.824659] dma-buf: Running sanitycheck [ 0.829043] dma-buf: Running dma_fence [ 0.833263] sizeof(dma_fence)=48 [ 0.836963] dma-buf: Running dma_fence/sanitycheck [ 0.842349] dma-buf: Running dma_fence/test_signaling [ 0.848043] dma-buf: Running dma_fence/test_add_callback [ 0.854000] dma-buf: Running dma_fence/test_late_add_callback [ 0.860431] dma-buf: Running dma_fence/test_rm_callback [ 0.866288] dma-buf: Running dma_fence/test_late_rm_callback [ 0.872613] dma-buf: Running dma_fence/test_status [ 0.877988] dma-buf: Running dma_fence/test_error [ 0.883256] dma-buf: Running dma_fence/test_wait [ 0.888420] dma-buf: Running dma_fence/test_wait_timeout [ 0.933217] dma-buf: Running dma_fence/test_stub [ 0.938397] dma-buf: Running dma_fence/race_signal_callback [ 1.013214] thread_signal_callback[0] completed 37185 passes, 85 misses [ 1.020642] thread_signal_callback[1] completed 37180 passes, 81 misses [ 1.093214] thread_signal_callback[0] completed 40857 passes, 40857 misses [ 1.100928] thread_signal_callback[1] completed 40831 passes, 40831 misses [ 1.109178] libphy: Fixed MDIO Bus: probed [ 1.114337] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator [ 1.125618] sunxi gmac driver's version: 1.0.0 [ 1.130768] gmac-power0: NULL [ 1.134134] gmac-power1: NULL [ 1.137447] gmac-power2: NULL [ 1.141623] usbcore: registered new interface driver catc [ 1.147764] usbcore: registered new interface driver kaweth [ 1.154013] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.162324] usbcore: registered new interface driver pegasus [ 1.168710] usbcore: registered new interface driver rtl8150 [ 1.175155] usbcore: registered new interface driver r8152 [ 1.181392] usbcore: registered new interface driver cdc_ether [ 1.187962] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.195338] sunxi-ehci: EHCI SUNXI driver [ 1.200287] get ehci1-controller wakeup-source is fail. [ 1.206262] sunxi ehci1-controller don't init wakeup source [ 1.212518] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xc0b67a38, 0x:c8839000, irq_no:40 [ 1.224518] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply drvvbus not found, using dummy regulator [ 1.237000] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator [ 1.249153] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller [ 1.256409] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1 [ 1.266353] sunxi-ehci 4200000.ehci1-controller: irq 64, io mem 0x04200000 [ 1.303230] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00 [ 1.311848] hub 1-0:1.0: USB hub found [ 1.316098] hub 1-0:1.0: 1 port detected [ 1.321035] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.328025] sunxi-ohci: OHCI SUNXI driver [ 1.332982] get ohci1-controller wakeup-source is fail. [ 1.338964] sunxi ohci1-controller don't init wakeup source [ 1.345233] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xc0b67cc8 [ 1.354897] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply drvvbus not found, using dummy regulator [ 1.367386] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator [ 1.379544] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller [ 1.386796] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2 [ 1.396675] sunxi-ohci 4200400.ohci1-controller: irq 65, io mem 0x04200400 [ 1.478022] hub 2-0:1.0: USB hub found [ 1.482269] hub 2-0:1.0: 1 port detected [ 1.487337] usbcore: registered new interface driver usb-storage [ 1.494221] i2c /dev entries driver [ 1.498213] sunxi cedar version 1.1 [ 1.502308] sunxi-cedar 1c0e000.ve: Adding to iommu group 0 [ 1.508632] VE: sunxi_cedar_probe power-domain init!!! [ 1.514407] VE: install start!!! [ 1.514407] [ 1.519891] VE: cedar-ve the get irq is 46 [ 1.519891] [ 1.526341] VE: ve_debug_proc_info:(ptrval), data:(ptrval), lock:(ptrval) [ 1.526341] [ 1.535621] VE: install end!!! [ 1.535621] [ 1.540683] VE: sunxi_cedar_probe [ 1.544641] Bluetooth: HCI UART driver ver 2.3 [ 1.549627] Bluetooth: HCI UART protocol H4 registered [ 1.555390] Bluetooth: HCI UART protocol BCSP registered [ 1.561328] Bluetooth: HCI UART protocol (null) registered [ 1.567478] Bluetooth: HCI Realtek H5 protocol initialized [ 1.575013] sun8iw20-pinctrl 2000000.pinctrl: pin PC2 already requested by 4025000.spi; cannot claim for 4022000.sdmmc [ 1.587030] sun8iw20-pinctrl 2000000.pinctrl: pin-66 (4022000.sdmmc) status -22 [ 1.595222] sun8iw20-pinctrl 2000000.pinctrl: could not request pin 66 (PC2) from group PC2 on device 2000000.pinctrl [ 1.607203] sunxi-mmc 4022000.sdmmc: Error applying setting, reverse things back [ 1.615516] sunxi-mmc: probe of 4022000.sdmmc failed with error -22 [ 1.623549] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.22 2021-12-20 15:40) [ 1.633494] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8 [ 1.639671] sunxi-mmc 4020000.sdmmc: No vmmc regulator found [ 1.646020] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found [ 1.652446] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found [ 1.658881] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found [ 1.665412] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found [ 1.671931] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found [ 1.678463] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found [ 1.685431] sunxi-mmc 4020000.sdmmc: Got CD GPIO [ 1.690946] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.702090] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator [ 1.722221] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.746613] sunxi-mmc 4020000.sdmmc: detmode:gpio irq [ 1.752288] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 1.763885] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.22 2021-12-20 15:40) [ 1.773850] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8 [ 1.780025] sunxi-mmc 4021000.sdmmc: No vmmc regulator found [ 1.786390] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found [ 1.792813] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found [ 1.799258] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found [ 1.805789] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found [ 1.812312] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found [ 1.818850] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found [ 1.825403] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed [ 1.834787] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.845944] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 1.866093] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.890297] sunxi-mmc 4021000.sdmmc: detmode:manually by software [ 1.897849] exFAT: Version 1.3.0 [ 1.901468] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 1.909154] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 1.916040] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.929153] sunxi-spdif 2036000.spdif: Not using gpio-spdif gpio from dts [ 1.937619] [AUDIOCODEC][sunxi_codec_parse_params][2412]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1 [ 1.937619] [ 1.954835] [AUDIOCODEC][sunxi_codec_parse_params][2448]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0 [ 1.966205] [AUDIOCODEC][sunxi_internal_codec_probe][2609]:codec probe finished [ 1.974433] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.986933] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present! [ 1.988235] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 1.996740] [SNDCODEC][sunxi_card_init][583]:card init finished [ 2.004225] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.017056] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok [ 2.017578] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.034033] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input0 [ 2.034505] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.052255] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 2.063635] [SNDCODEC][sunxi_card_dev_probe][836]:register card finished [ 2.072507] NET: Registered protocol family 10 [ 2.078634] Segment Routing with IPv6 [ 2.082850] NET: Registered protocol family 17 [ 2.087860] [SNDCODEC][sunxi_hs_init_work][259]:resume-->report switch [ 2.095348] Bluetooth: RFCOMM TTY layer initialized [ 2.100827] Bluetooth: RFCOMM socket layer initialized [ 2.106618] Bluetooth: RFCOMM ver 1.11 [ 2.111449] Registering SWP/SWPB emulation handler [ 2.130782] sun8iw20-pinctrl 2000000.pinctrl: pin PC2 already requested by 4025000.spi; cannot claim for 4022000.sdmmc [ 2.142814] sun8iw20-pinctrl 2000000.pinctrl: pin-66 (4022000.sdmmc) status -22 [ 2.151036] sun8iw20-pinctrl 2000000.pinctrl: could not request pin 66 (PC2) from group PC2 on device 2000000.pinctrl [ 2.163014] sunxi-mmc 4022000.sdmmc: Error applying setting, reverse things back [ 2.171348] sunxi-mmc: probe of 4022000.sdmmc failed with error -22 [ 2.178771] sunxi-i2c sunxi-i2c2: sunxi-i2c2 supply twi not found, using dummy regulator [ 2.188407] sunxi-i2c sunxi-i2c2: probe success [ 2.194847] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator [ 2.207104] sunxi-audio-card 203605c.soundspdif: use dummy codec for simple card. [ 2.215646] debugfs: Directory '2036000.spdif' with parent 'sndspdif' already present! [ 2.224947] sunxi-audio-card 203605c.soundspdif: snd-soc-dummy-dai <-> 2036000.spdif mapping ok [ 2.235715] get ehci0-controller wakeup-source is fail. [ 2.241662] sunxi ehci0-controller don't init wakeup source [ 2.247953] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xc0b67518, 0x:c88af000, irq_no:3e [ 2.259950] [sunxi-ehci0]: Not init ehci0 [ 2.264770] get ohci0-controller wakeup-source is fail. [ 2.270728] sunxi ohci0-controller don't init wakeup source [ 2.276981] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xc0b677a8 [ 2.286636] [sunxi-ohci0]: Not init ohci0 [ 2.292174] get usb_detect_mode is fail, -22 [ 2.297020] get det_vbus is fail, -84 [ 2.301111] get id is fail, -84 [ 2.306585] clk: Not disabling unused clocks [ 2.311367] ALSA device list: [ 2.315130] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 2.324818] #0: audiocodec [ 2.324823] #1: sndspdif [ 2.331084] cfg80211: failed to load regulatory.db [ 2.336586] Waiting 2 sec before mounting root device... [ 3.333226] [ 3.333226] insmod_device_driver [ 3.333226] [ 3.340394] sunxi_usb_udc 4100000.udc-controller: 4100000.udc-controller supply udc not found, using dummy regulator [ 3.352446] device_chose finished 142! [ 4.373388] VFS: Cannot open root device "mmcblk0p5" or unknown-block(0,0): error -6 [ 4.382051] Please append a correct "root=" boot option; here are the available partitions: [ 4.391429] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 4.400679] CPU0: stopping [ 4.403708] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.61 #53 [ 4.410419] Hardware name: Generic DT based system [ 4.415799] [<c010dee8>] (unwind_backtrace) from [<c010a678>] (show_stack+0x10/0x14) [ 4.424461] [<c010a678>] (show_stack) from [<c065f470>] (dump_stack+0x88/0xa4) [ 4.432546] [<c065f470>] (dump_stack) from [<c010c2b4>] (handle_IPI+0xe4/0x180) [ 4.440722] [<c010c2b4>] (handle_IPI) from [<c03171e0>] (gic_handle_irq+0x70/0x78) [ 4.449195] [<c03171e0>] (gic_handle_irq) from [<c01021cc>] (__irq_svc+0x6c/0xa8) [ 4.457559] Exception stack(0xc0a01f40 to 0xc0a01f88) [ 4.463211] 1f40: 0000087c c7abb334 00000000 c0114800 00000001 c0a00000 c0a04e24 c0a04e60 [ 4.472357] 1f60: c0a4d000 c7bff540 c09280c0 00000000 00000001 c0a01f90 c0107fb0 c0107fa0 [ 4.481502] 1f80: 60000013 ffffffff [ 4.485406] [<c01021cc>] (__irq_svc) from [<c0107fa0>] (arch_cpu_idle+0x1c/0x38) [ 4.493685] [<c0107fa0>] (arch_cpu_idle) from [<c013d564>] (do_idle+0xd4/0x128) [ 4.501860] [<c013d564>] (do_idle) from [<c013d848>] (cpu_startup_entry+0x18/0x20) [ 4.510334] [<c013d848>] (cpu_startup_entry) from [<c0900c80>] (start_kernel+0x360/0x3ec) [ 4.519481] [<c0900c80>] (start_kernel) from [<00000000>] (0x0) [ 4.526108] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]--- ]]>https://bbs.aw-ol.com/topic/3713/t113的emmc启动-挂载文件系统失败RSS for NodeFri, 11 Sep 2026 16:34:06 GMTFri, 16 Jun 2023 07:08:22 GMT60<![CDATA[Reply to t113的emmc启动，挂载文件系统失败 on Fri, 16 Jun 2023 09:10:26 GMT]]>@lucky123456 在 t113的emmc启动，挂载文件系统失败 中说：

@lucky123456 已解决

是怎么回事呢？

]]>https://bbs.aw-ol.com/post/16522https://bbs.aw-ol.com/post/16522Fri, 16 Jun 2023 09:10:26 GMT<![CDATA[Reply to t113的emmc启动，挂载文件系统失败 on Fri, 16 Jun 2023 08:37:46 GMT]]>@lucky123456 已解决

]]>https://bbs.aw-ol.com/post/16521https://bbs.aw-ol.com/post/16521Fri, 16 Jun 2023 08:37:46 GMT