[755]fes begin commit:adaf1174cc
[758]set pll start
[760]periph0 has been enabled
[763]set pll end
[765][pmu]: bus read error
[767]board init ok
[769]beign to init dram
[771]ZQ value = 0x2f
[773]get_pmu_exist() = -1
[775]ddr_efuse_type: 0xa
[778]trefi:7.8ms
[780][AUTO DEBUG] single rank and full DQ!
[784]ddr_efuse_type: 0xa
[786]trefi:7.8ms
[788][AUTO DEBUG] rank 0 row = 13
[791][AUTO DEBUG] rank 0 bank = 4
[794][AUTO DEBUG] rank 0 page size = 2 KB
[798]DRAM BOOT DRIVE INFO: V0.33
[801]DRAM CLK = 528 MHz
[803]DRAM Type = 2 (2:DDR2,3:DDR3)
[807]DRAMC read ODT  off.
[809]DRAM ODT off.
[811]ddr_efuse_type: 0xa
[814]DRAM SIZE =64 M
[815]dram_tpr4:0x0
[817]PLL_DDR_CTRL_REG:0xf8002b00
[820]DRAM_CLK_REG:0xc0000000
[823][TIMING DEBUG] MR2= 0x0
[827]DRAM simple test OK.
[830]init dram ok


U-Boot 2018.05-g2a1965a (Jul 10 2022 - 02:50:57 +0000) Allwinner Technology

[03.407]DRAM:  64 MiB
[03.412]Relocation Offset is: 01ed9000
[03.438]secure enable bit: 0
[03.444]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
[03.450]flash init start
[03.453]workmode = 16,storage type = 0
try card 2
set card number 2
get card number 2
[03.460][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00
[03.470][mmc]: get sdc_type fail and use default host:tm4.
[03.500][mmc]: Is not Boot mode!
[03.503][mmc]: SUNXI SDMMC Controller Version:0x50310
[03.514][mmc]: ************Try SD card 2************
[03.519][mmc]: mmc 2 cmd timeout 100 status 100
[03.524][mmc]: smc 2 err, cmd 8,  RTO
[03.527][mmc]: mmc 2 close bus gating and reset
[03.532][mmc]: mmc 2 cmd timeout 100 status 100
[03.536][mmc]: smc 2 err, cmd 55,  RTO
[03.540][mmc]: mmc 2 close bus gating and reset
[03.544][mmc]: ************Try MMC card 2************
[03.553][mmc]: mmc 2 cmd timeout 100 status 100
[03.557][mmc]: smc 2 err, cmd 1,  RTO
[03.560][mmc]: mmc 2 close bus gating and reset
[03.565][mmc]: Card did not respond to voltage select!
[03.569][mmc]: ************SD/MMC 2 init error!************
[03.575][mmc]: mmc init product failed
MMC init failed
try emmc fail
[03.591]sunxi-spinand: AW SPINand MTD Layer Version: 1.8 20220106
[03.596]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.11 20211217
[03.657]sunxi-spinand-phy: request spi0 gpio ok
[03.661]sunxi-spinand-phy: request general tx dma channel ok!
[03.666]sunxi-spinand-phy: request general rx dma channel ok!
[03.672]sunxi-spinand-phy: set spic0 clk to 20 Mhz
[03.676]sunxi-spinand-phy: init spic0 clk ok
[04.680]sunxi-spinand-phy: read id failed : -110
try nand fail
[05.949]spi sunxi_slave->max_hz:100000000
[06.962]Sample mode:1 start:0 end:48 right_sample_delay:0x18
SF: Detected w25q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
[07.101]line:703 init_clocks
[07.115]init_clocks:finish
[07.122]Loading Environment from SUNXI_FLASH... OK
[07.135]try to burn key
[07.139]out of usb burn from boot: not need burn key
[07.143]Net:   [07.145]No ethernet found.
Hit any key to stop autoboot:  0
sunxi work mode=0x10
run usb efex
delay time 2500
weak:otg_phy_config
usb init ok
set address 0x1e
set address 0x1e ok
SUNXI_EFEX_ERASE_TAG
erase_flag = 0x12
origin_erase_flag = 0x1
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0

新手刚入手一块f133的开发板，焊接了一块华邦w25q128，还请折腾过大佬们指教指教。