<![CDATA[Waiting for root device /dev/mmcblk0p0 后面就不动了]]>Bytes transferred = 20311 (4f57 hex) ## Booting kernel from Legacy Image at 28100000 ... Image Name: Smartx Image Type: AArch64 Linux Kernel Image (gzip compressed) Data Size: 3863378 Bytes = 3.7 MiB Load Address: 200a0000 Entry Point: 200a0000 Verifying Checksum ... OK ## Flattened Device Tree blob at 28900000 Booting using the fdt blob at 0x28900000 Uncompressing Kernel Image Using Device Tree in place at 0000000028900000, end 0000000028907f56 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.38 (build@ubuntu20) (gcc version 7.5.0 (Linaro GCC 7.5-2019.12) ) #1 SMP Thu Dec 29 17:21:56 CST 2022 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] Memory limited to 512MB [ 0.000000] Icc memory setup at 0x0000000022200000 size 0x0000000000000800 KB [ 0.000000] OF: reserved mem: initialized node icc@0x22200000, compatible id icc-region [ 0.000000] cma: Reserved 16 MiB at 0x000000003f000000 [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] DMA zone: 2048 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 131072 pages, LIFO batch:31 [ 0.000000] percpu: Embedded 20 pages/cpu @ffffffc03ef88000 s44696 r8192 d29032 u81920 [ 0.000000] pcpu-alloc: s44696 r8192 d29032 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129024 [ 0.000000] Kernel command line: console=ttyS0,115200,earlyprintk loglevel=8,quiet root=/dev/mmcblk0p0 rootwait ro rootfstype=ext4 mem=512m OS_MEM=512 TOTAL_MEM=1024 [ 0.000000] PID hash table entries: 2048 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.000000] Memory: 451200K/524288K available (7550K kernel code, 386K rwdata, 1588K rodata, 2048K init, 364K bss, 56704K reserved, 16384K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff80080a0000 - 0xffffff8008800000 ( 7552 KB) [ 0.000000] .rodata : 0xffffff8008800000 - 0xffffff8008a00000 ( 2048 KB) [ 0.000000] .init : 0xffffff8008a00000 - 0xffffff8008c00000 ( 2048 KB) [ 0.000000] .data : 0xffffff8008c00000 - 0xffffff8008c60808 ( 387 KB) [ 0.000000] .bss : 0xffffff8008c60808 - 0xffffff8008cbb834 ( 365 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00800000 - 0xffffffbf01000000 ( 8 MB actual) [ 0.000000] memory : 0xffffffc020000000 - 0xffffffc040000000 ( 512 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 250.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x7350b89c29, max_idle_ns: 881590431910 ns [ 0.000004] sched_clock: 56 bits at 250MHz, resolution 4ns, wraps every 4398046511102ns [ 0.000215] Console: colour dummy device 80x25 [ 0.000233] Calibrating delay loop (skipped), value calculated using timer frequency.. 500.00 BogoMIPS (lpj=2500000) [ 0.000242] pid_max: default: 32768 minimum: 301 [ 0.000307] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes) [ 0.000314] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes) [ 0.000832] ASID allocator initialised with 65536 entries [ 0.002086] Detected VIPT I-cache on CPU1 [ 0.002126] CPU1: Booted secondary processor [410fd034] [ 0.002344] Detected VIPT I-cache on CPU2 [ 0.002366] CPU2: Booted secondary processor [410fd034] [ 0.002570] Detected VIPT I-cache on CPU3 [ 0.002592] CPU3: Booted secondary processor [410fd034] [ 0.002634] Brought up 4 CPUs [ 0.002654] SMP: Total of 4 processors activated. [ 0.002661] CPU features: detected feature: 32-bit EL0 Support [ 0.002669] CPU: All CPU(s) started at EL1 [ 0.002684] alternatives: patching kernel code [ 0.003125] devtmpfs: initialized [ 0.007163] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.007179] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.008254] NET: Registered protocol family 16 [ 0.008974] vdso: 2 pages (1 code @ ffffff8008807000, 1 data @ ffffff8008c04000) [ 0.008987] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.009554] DMA: preallocated 256 KiB pool for atomic allocations [ 0.018843] SCSI subsystem initialized [ 0.018985] usbcore: registered new interface driver usbfs [ 0.019021] usbcore: registered new interface driver hub [ 0.019060] usbcore: registered new device driver usb [ 0.020013] Linux video capture interface: v2.00 [ 0.020267] icc-smartchip icc-smartchip: assigned reserved memory node icc@0x22200000 [ 0.023833] Advanced Linux Sound Architecture Driver Initialized. [ 0.024477] clocksource: Switched to clocksource arch_sys_counter [ 0.029458] NET: Registered protocol family 2 [ 0.029842] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.029886] TCP bind hash table entries: 4096 (order: 4, 65536 bytes) [ 0.029956] TCP: Hash tables configured (established 4096 bind 4096) [ 0.029998] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.030017] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.030122] NET: Registered protocol family 1 [ 0.030347] RPC: Registered named UNIX socket transport module. [ 0.030353] RPC: Registered udp transport module. [ 0.030358] RPC: Registered tcp transport module. [ 0.030362] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.031442] workingset: timestamp_bits=62 max_order=17 bucket_order=0 [ 0.037990] exFAT: file-system version 2.2.0-3arter97 [ 0.038575] NFS: Registering the id_resolver key type [ 0.038593] Key type id_resolver registered [ 0.038598] Key type id_legacy registered [ 0.038608] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.038632] fuse init (API version 7.26) [ 0.040745] io scheduler noop registered [ 0.040752] io scheduler deadline registered [ 0.040860] io scheduler cfq registered (default) [ 0.044396] pwm probe success! [ 0.044515] pwm probe success! [ 0.044890] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.046016] console [ttyS0] disabled [ 0.066133] 8500000.serial: ttyS0 at MMIO 0x8500000 (irq = 7, base_baud = 9375000) is a 16550A [ 0.661875] console [ttyS0] enabled [ 0.685702] 8510000.serial: ttyS1 at MMIO 0x8510000 (irq = 8, base_baud = 9375000) is a 16550A [ 0.714624] 8520000.serial: ttyS2 at MMIO 0x8520000 (irq = 9, base_baud = 9375000) is a 16550A [ 0.743531] 8530000.serial: ttyS3 at MMIO 0x8530000 (irq = 10, base_baud = 9375000) is a 16550A [ 0.772526] 8540000.serial: ttyS4 at MMIO 0x8540000 (irq = 11, base_baud = 9375000) is a 16550A [ 0.787871] brd: module loaded [ 0.794365] loop: module loaded [ 0.797879] enter dw_spi_add_host [ 0.801679] enter dw_spi_add_host [ 0.806027] dw_spi_mmio 8140000.spim1: cs4 >= max 4 [ 0.810884] spi_master spi1: spi_device register error /soc/spim1@8140000/spidev@4 [ 0.818431] spi_master spi1: Failed to create SPI device for /soc/spim1@8140000/spidev@4 [ 0.826544] enter dw_spi_add_host [ 0.830301] enter dw_spi_add_host [ 0.834145] Smartx mdio probe... [ 0.847437] libphy: smartx_mii_bus: probed [ 0.851822] smartx mdio register succussfully. [ 0.856412] libphy: Fixed MDIO Bus: probed [ 0.860821] CAN device driver interface [ 0.913788] smartx-gmac 1130000.ethernet: eth0: Beyond Ethernet Controller at 0xffffff8008d1c000, a2:e7:c3:1b:e5:60, IRQ 27tx_fifo:3 tx_fifo_1000: 2 [ 0.913788] tx_enable: 1 rx_enable: 1 [ 0.930669] Ethernet flags: [ 0.933362] Gigabit , coalesce[ 0.936335] [ 0.937882] usbcore: registered new interface driver cdc_ether [ 0.943709] usbcore: registered new interface driver rndis_host [ 0.949721] 11c0000.usb supply vusb_d not found, using dummy regulator [ 0.956258] 11c0000.usb supply vusb_a not found, using dummy regulator [ 0.962926] 1200000.usb supply vusb_d not found, using dummy regulator [ 0.969452] 1200000.usb supply vusb_a not found, using dummy regulator [ 0.982232] dwc2 1200000.usb: DWC OTG Controller [ 0.986857] dwc2 1200000.usb: new USB bus registered, assigned bus number 1 [ 0.993801] dwc2 1200000.usb: irq 13, io mem 0x01200000 [ 0.999568] hub 1-0:1.0: USB hub found [ 1.003322] hub 1-0:1.0: 1 port detected [ 1.007542] 1240000.usb supply vusb_d not found, using dummy regulator [ 1.014059] 1240000.usb supply vusb_a not found, using dummy regulator [ 1.026774] dwc2 1240000.usb: DWC OTG Controller [ 1.031380] dwc2 1240000.usb: new USB bus registered, assigned bus number 2 [ 1.038332] dwc2 1240000.usb: irq 14, io mem 0x01240000 [ 1.044003] hub 2-0:1.0: USB hub found [ 1.047765] hub 2-0:1.0: 1 port detected [ 1.052114] usbcore: registered new interface driver usb-storage [ 1.058161] usbcore: registered new interface driver usbserial [ 1.063988] usbcore: registered new interface driver option [ 1.069561] usbserial: USB Serial support registered for GSM modem (1-port) [ 1.076873] smart-rtc 1076000.rtc: rtc core: registered 1076000.rtc as rtc0 [ 1.083848] i2c /dev entries driver [ 1.087702] usbcore: registered new interface driver uvcvideo [ 1.093419] USB Video Class driver (1.1.1) [ 1.097810] ina2xx 0-0040: error configuring the device: -121 [ 1.103654] ina2xx 0-0042: error configuring the device: -121 [ 1.109496] ina2xx 0-0043: error configuring the device: -121 [ 1.115336] ina2xx 1-0041: error configuring the device: -121 [ 1.121172] ina2xx 1-0044: error configuring the device: -121 [ 1.127347] sdhci: Secure Digital Host Controller Interface driver [ 1.133496] sdhci: Copyright(c) Pierre Ossman [ 1.137845] Synopsys Designware Multimedia Card Interface Driver [ 1.148074] dwmmc_smartchip 9000000.mmc: IDMAC supports 32-bit address mode. [ 1.155194] dwmmc_smartchip 9000000.mmc: Using internal DMA controller. [ 1.161783] dwmmc_smartchip 9000000.mmc: Version ID is 290a [ 1.167366] dwmmc_smartchip 9000000.mmc: DW MMC controller at irq 26,32 bit host data width,128 deep fifo [ 1.177431] dwmmc_smartchip 9000000.mmc: 3 slots initialized [ 1.183148] mmc_host mmc1: sd card set 3.3 V [ 1.215492] mmc_host mmc1: Bus speed (slot 0) = 200000000Hz (slot req 400000Hz, actual 400000HZ div = 250) [ 1.254556] mmc_host mmc2: sd card set 3.3 V [ 1.284488] mmc_host mmc2: Bus speed (slot 1) = 200000000Hz (slot req 400000Hz, actual 400000HZ div = 250) [ 1.314559] mmc_host mmc3: sd card set 3.3 V [ 1.344488] mmc_host mmc3: Bus speed (slot 2) = 200000000Hz (slot req 400000Hz, actual 400000HZ div = 250) [ 1.374535] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.384320] mmc0: Unknown controller version (5). You may experience problems. [ 1.454486] mmc0: SDHCI controller on 1020000.sdhci [1020000.sdhci] using ADMA [ 1.461747] hidraw: raw HID events driver (C) Jiri Kosina [ 1.467211] usbcore: registered new interface driver usbhid [ 1.472755] usbhid: USB HID core driver [ 1.477251] NET: Registered protocol family 10 [ 1.482321] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.488638] NET: Registered protocol family 17 [ 1.493065] can: controller area network core (rev 20120528 abi 9) [ 1.499349] NET: Registered protocol family 29 [ 1.503772] can: raw protocol (rev 20120528) [ 1.508030] can: broadcast manager protocol (rev 20161123 t) [ 1.513665] can: netlink gateway (rev 20130117) max_hops=1 [ 1.519342] Key type dns_resolver registered [ 1.524488] 11c0000.usb supply vusb_d not found, using dummy regulator [ 1.531027] 11c0000.usb supply vusb_a not found, using dummy regulator [ 1.543775] dwc2 11c0000.usb: DWC OTG Controller [ 1.548399] dwc2 11c0000.usb: new USB bus registered, assigned bus number 3 [ 1.555352] dwc2 11c0000.usb: irq 12, io mem 0x011c0000 [ 1.561026] hub 3-0:1.0: USB hub found [ 1.564790] hub 3-0:1.0: 1 port detected [ 1.568964] smart-rtc 1076000.rtc: setting system clock to 1970-01-01 00:00:37 UTC (37) [ 1.577039] ALSA device list: [ 1.579992] No soundcards found. [ 1.583546] Waiting for root device /dev/mmcblk0p0... [ 1.639314] mmc0: new high speed MMC card at address 0001 [ 1.645002] mmcblk0: mmc0:0001 88A398 7.28 GiB [ 1.649628] mmcblk0boot0: mmc0:0001 88A398 partition 1 4.00 MiB [ 1.655639] mmcblk0boot1: mmc0:0001 88A398 partition 2 4.00 MiB [ 1.661637] mmcblk0rpmb: mmc0:0001 88A398 partition 3 4.00 MiB ]]>https://bbs.aw-ol.com/topic/4422/waiting-for-root-device-dev-mmcblk0p0-后面就不动了RSS for NodeThu, 16 Apr 2026 03:29:31 GMTMon, 16 Oct 2023 03:29:32 GMT60<![CDATA[Reply to Waiting for root device /dev/mmcblk0p0 后面就不动了 on Mon, 16 Oct 2023 06:32:24 GMT]]>@yxfzz 在 Waiting for root device /dev/mmcblk0p0 后面就不动了 中说：

[ 1.384320] mmc0: Unknown controller version (5). You may experience problems.

换张卡试一试

]]>https://bbs.aw-ol.com/post/19239https://bbs.aw-ol.com/post/19239Mon, 16 Oct 2023 06:32:24 GMT<![CDATA[Reply to Waiting for root device /dev/mmcblk0p0 后面就不动了 on Mon, 16 Oct 2023 04:59:10 GMT]]>@yxfzz mmc引导到了mmcblk0boot0，rootfs挂载不上

]]>https://bbs.aw-ol.com/post/19236https://bbs.aw-ol.com/post/19236Mon, 16 Oct 2023 04:59:10 GMT