T113 无法启动
-
燒入編譯的image 之後無法啟動
log 如下[32]HELLO! BOOT0 is starting! [35]BOOT0 commit : 1417090655 [38]set pll start [44]periph0 has been enabled [47]set pll end [48][pmu]: bus read error [51]board init ok [53]enable_jtag [54]key press : ? [56]ZQ value = 0x2e [58]get_pmu_exist() = -1 [60]DRAM BOOT DRIVE INFO: V0.33 [63]DRAM CLK = 792 MHz [65]DRAM Type = 3 (2:DDR2,3:DDR3) [69]DRAMC read ODT off. [71]DRAM ODT value: 0x42. [74]ddr_efuse_type: 0xa [77]DRAM SIZE =128 M [79]dram_tpr4:0x0 [80]PLL_DDR_CTRL_REG:0xf8004100 [83]DRAM_CLK_REG:0xc0000000 [86][TIMING DEBUG] MR2= 0x18 [94]DRAM simple test OK. [96]rtc standby flag is 0x0, super standby flag is 0x0 [101]dram size =128 [104]card no is 2 [106]sdcard 2 line count 4 [108][mmc]: mmc driver ver 2021-05-21 14:47 [118][mmc]: Wrong media type 0x0, but host sdc2, try mmc first [123][mmc]: ***Try MMC card 2*** [146][mmc]: RMCA OK! [148][mmc]: wrong freq 2 at spd md 2 [152][mmc]: mmc 2 bias 0 [155][mmc]: MMC 5.1 [157][mmc]: HSSDR52/SDR25 4 bit [160][mmc]: 50000000 Hz [162][mmc]: 7396 MB [164][mmc]: ***SD/MMC 2 init OK!!!*** [255]Loading boot-pkg Succeed(index=0). [259]Entry_name = u-boot [266]Entry_name = optee [270]Entry_name = dtb [273]tunning data addr:0x430003e8 [276]Jump to second Boot. M/TC: OP-TEE version: 8b49ce62-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Fri Aug 12 08:24:15 UTC 2022 arm U-Boot 2018.07 (Dec 11 2023 - 06:46:44 +0000) Allwinner Technology [00.326]CPU: Allwinner Family [00.329]Model: sun8iw20 [00.332]DRAM: 128 MiB [00.335]Relocation Offset is: 04ec9000 [00.361]secure enable bit: 0 E/TC:0 fdt_getprop_u32:343 prop trace_level not found [00.375]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz [00.381]gic: sec monitor mode sunxi flash map init [00.386]flash init start [00.388]workmode = 0,storage type = 2 [00.392][mmc]: mmc driver ver uboot2018:2022-12-07 18:56:00 [00.398][mmc]: SUNXI SDMMC Controller Version:0x50310 [00.422][mmc]: Best spd md: 1-HSSDR52/SDR25, freq: 2-50000000, Bus width: 4 [00.429]sunxi flash init ok [00.431]line:703 init_clocks [00.434]drv_disp_init [00.439]handle_num : 6 request pwm success, pwm7:pwm7:0x2000c00. [00.450]drv_disp_init finish [00.454]Loading Environment from SUNXI_FLASH... Can't find env-redund partition *** Warning - no device, using default environment Failed (-19) [00.474]boot_gui_init:start [00.477]set disp.dev2_output_type fail. using defval=0 [00.483]set disp.fb0_rot_used fail. using defval=0 [00.487]set disp.fb0_rot_degree fail. using defval=0 [00.493]boot_gui_init:finish partno erro : can't find partition bootloader partno erro : can't find partition boot-resource [00.504]Get bootloader and boot-resource partition number fail! [00.510]Item0 (Map) magic is bad [00.513]the secure storage item0 copy0 magic is bad [00.517]Item0 (Map) magic is bad [00.520]the secure storage item0 copy1 magic is bad [00.525]Item0 (Map) magic is bad [00.528]usb burn from boot delay time 0 weak:otg_phy_config [00.539]usb prepare ok [00.663]LCD open finish [00.746]usb sof ok [00.747]usb probe ok [00.749]usb setup ok set address 0x24 set address 0x24 ok try to update [01.154]do_burn_from_boot usb : have no handshake cann't get the boot_base from the env [01.173]update part info [01.175]update bootcmd [01.178]change working_fdt 0x44888e70 to 0x44868e70 [01.183][mmc]: no mmc-hs400-1_8v! [01.186][mmc]: delete mmc-hs200-1_8v from dtb [01.190][mmc]: delete mmc-ddr-1_8v from dtb [01.194][mmc]: get max-frequency ok 50000000 Hz disable nand error: FDT_ERR_BADPATH [01.220]update dts Hit any key to stop autoboot: 0 ## Error: "distro_bootcmd" not defined =>
按照Tina_Linux_系统软件_开发指南 編的image
source build/envsetup.sh
lunch t113-evb1_auto-tina
make -j1
pack用PhoenixSuit, 選用分區擦除升級
有人能幫忙看看問題出在哪嗎? -
This post is deleted!
Copyright © 2023 深圳全志在线有限公司 粤ICP备2021084185号 粤公网安备44030502007680号