启动日志如下，DDR已经降频，目前使用PhoenixCard 启动卡烧录。
[32]HELLO! BOOT0 is starting!
[35]BOOT0 commit : 88480af
[37]set pll start
[39]periph0 has been enabled
[42]set pll end
[44][pmu]: bus read error
[46]board init ok
[48]get_pmu_exist() = -1
[50]ddr_efuse_type: 0x0
[53]trefi:7.8ms
[55][AUTO DEBUG] single rank and full DQ!
[59]ddr_efuse_type: 0x0
[61]trefi:7.8ms
[63][AUTO DEBUG] rank 0 row = 15
[66][AUTO DEBUG] rank 0 bank = 8
[69][AUTO DEBUG] rank 0 page size = 2 KB
[73]DRAM BOOT DRIVE INFO: V0.33
[76]DRAM CLK = 672 MHz
[78]DRAM Type = 3 (2:DDR2,3:DDR3)
[81]DRAMC ZQ value: 0x7b7bfb
[84]DRAM ODT value: 0x42.
[87]ddr_efuse_type: 0x0
[90]DRAM SIZE =512 M
[92]dram_tpr4:0x0
[93]PLL_DDR_CTRL_REG:0xf8003700
[96]DRAM_CLK_REG:0xc0000000
[99][TIMING DEBUG] MR2= 0x18
[103]DRAM simple test OK.
[105]dram size =512
[107]card no is 0
[109]sdcard 0 line count 4
[111][mmc]: mmc driver ver 2021-04-2 16:45
[121][mmc]: Wrong media type 0x0
[124][mmc]: ***Try SD card 0***
[133][mmc]: DS26/SDR12 4 bit
[136][mmc]: 25000000 Hz
[138][mmc]: 14922 MB
[140][mmc]: ***SD/MMC 0 init OK!!!***
[233]Loading boot-pkg Succeed(index=0).
[237]Entry_name = opensbi
[240]Entry_name = u-boot
[244]Entry_name = dtb
[247]mmc not para
[248]Jump to second Boot.
OpenSBI auto-t113-linux-V0.8-3-ge39e937
____ _____ ____ _____
/ __ \ / ____| _ \_ _|
| | | |_ __ ___ _ __ | (___ | |_) || |
| | | | '_ \ / _ \ '_ \ \___ \| _ < | |
| |__| | |_) | __/ | | |____) | |_) || |_
\____/| .__/ \___|_| |_|_____/|____/_____|
| |
|_|
Platform Name : T-HEAD Xuantie Platform
Platform HART Features : RV64ACDFIMSUVX
Platform Max HARTs : 1
Current Hart : 0
Firmware Base : 0x41fc0400
Firmware Size : 75 KB
Runtime SBI Version : 0.2
MIDELEG : 0x0000000000000222
MEDELEG : 0x000000000000b1ff
PMP0 : 0x0000000041fc0000-0x0000000041fdffff (A)
PMP1 : 0x0000000040000000-0x000000007fffffff (A,R,W,X)
PMP2 : 0x0000000080000000-0x00000000bfffffff (A,R,W,X)
PMP3 : 0x0000000000020000-0x0000000000027fff (A,▒[00.329][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00
[00.334][mmc]: get sdc_type fail and use default host:tm1.
[00.340][mmc]: can't find node "mmc0",will add new node
[00.345][mmc]: fdt err returned <no error>
[00.349][mmc]: Using default timing para
[00.352][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.370][mmc]: card_caps:0x3000000a
[00.373][mmc]: host_caps:0x3000003f
[00.377][mmc]: sd set card speed failed
[00.381][mmc]: sd set card speed failed
[00.436]set disp.dev2_output_type fail. using defval=0
[00.463]set disp.fb0_rot_used fail. using defval=0
[00.467]set disp.fb0_rot_degree fail. using defval=0
[00.651]out of usb burn from boot: not need burn key
[00.656]Item0 (Map) magic is bad
[00.659]the secure storage item0 copy0 magic is bad
[00.665]Item0 (Map) magic is bad
[00.667]the secure storage item0 copy1 magic is bad
[00.672]Item0 (Map) magic is bad
[00.684]The storage not support sample function
[00.758]dts_get_dsp_memory: no /reserved-memory/dsp0 in fdt
[00.763]dts_get_dsp_memory fail
[01.109]no vendor_boot partition is found
[01.310]
Starting kernel ...
[01.312][mmc]: MMC Device 2 not found
[01.316][mmc]: mmc 2 not find, so not exit
[ 0.184186] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed
[ 0.191571] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed
[ 0.269231] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 0.276901] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 0.290879] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 0.298430] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 0.306034] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 0.313640] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 0.402182] sunxi-i2c sunxi-i2c2: Bus error
[ 0.406855] sunxi-i2c sunxi-i2c2: engine mode: I2C BUS error state is 0x0
[ 0.414489] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[ 0.422055] sunxi-i2c sunxi-i2c2: STOP failed!
[ 0.427048] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x38)
formating /dev/by-name/UDISK to ext4
/etc/preinit: line 1: mkfs.ext4: not found
[ 7.274902] block: extroot: cannot find device UDISK
Please press Enter to activate this console.
[ 9.099871] configfs-gadget 4100000.udc-controller: failed to start g1: -19
[ 11.612226] ======== XRADIO WIFI OPEN ========
[ 11.628926] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31
[ 11.635685] [XRADIO] Allocated hw_priv @ (____ptrval____)
[ 11.929343] [XRADIO] Detect SDIO card 1
[ 11.955359] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 11.963127] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 11.975337] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 11.983044] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 11.990732] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 11.998349] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 14.109073] [XRADIO] Remove SDIO card 1
[ 14.123353] [SBUS_ERR] sdio probe timeout!
[ 14.127922] [XRADIO_ERR] sbus_sdio_init failed
[ 14.133754] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 14.140953] xradio_core_init failed (-110)!
[ 14.145642] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 14.157885] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 14.165500] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 14.173138] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 14.180756] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
kmodloader done
