lcd0: lcd0@01c0c000 {

		lcd_used            = <1>;

		lcd_driver_name     = "default_lcd";
		lcd_backlight       = <50>;
		lcd_if              = <0>;
		lcd_hv_if = <0>;
		// lcd_cpu_if = <0>;

		lcd_x               = <1024>;
		lcd_y               = <600>;
		lcd_width           = <155>;
		lcd_height          = <86>;
		lcd_dclk_freq       = <48>;

		lcd_pwm_used        = <1>;
		lcd_pwm_ch          = <0>;
		lcd_pwm_freq        = <50000>;
		lcd_pwm_pol         = <0>;
		lcd_pwm_max_limit   = <255>;


		lcd_hbp             = <160>;
		lcd_ht              = <1344>;
		lcd_hspw            = <20>;
		lcd_vbp             = <23>;
		lcd_vt              = <635>;
		lcd_vspw            = <5>;

		lcd_lvds_if         = <0>;
		lcd_lvds_colordepth = <0>;
		lcd_lvds_mode       = <0>;
		lcd_frm             = <0>;
		lcd_io_phase        = <0x0000>;
		lcd_gamma_en        = <0>;
		lcd_bright_curve_en = <0>;
		lcd_cmap_en         = <0>;

		lcd_rb_swap			= <1>;

		deu_mode            = <0>;
		lcdgamma4iep        = <22>;
		smart_color         = <90>;

		// lcd_frm             = <0>;
		// lcd_io_phase        = <0x0000>;
		// lcd_gamma_en        = <0>;
		// lcd_bright_curve_en = <0>;
		// lcd_cmap_en         = <0>;

		// deu_mode            = <0>;
		// lcdgamma4iep        = <22>;
		// smart_color         = <90>;

		// lcd_dsi_if          = <0>;
		// lcd_dsi_lane        = <4>;
		// lcd_dsi_format      = <0>;
		// lcd_dsi_te          = <0>;
		// lcd_dsi_eotp        = <0>;

		lcd_pin_power = "dcdc1";
		lcd_pin_power1 = "eldo1";

		lcd_power = "dc1sw";
		
		lcd_bl_en = <&pio PB 8 1 0 3 1>;
		// lcd_gpio_0 = <&pio PB 8 1 0 3 1>;
		lcd_gpio_0 = <&pio PD 22 1 0 3 1>;
		pinctrl-0 = <&rgb18_pins_a>;
		pinctrl-1 = <&rgb18_pins_b>;

	};

disp: disp@06000000 {
disp_init_enable = <1>;
disp_mode = <0>;

		screen0_output_type      = <1>;
		screen0_output_mode      = <4>;
		screen0_output_format    = <0>;

		screen1_output_type      = <3>;
		screen1_output_mode      = <10>;

		screen1_output_format    = <0>;
		screen1_output_bits      = <0>;
		screen1_output_eotf      = <4>;
		screen1_output_cs        = <257>;
		screen1_output_dvi_hdmi  = <2>;
		screen1_output_range     = <2>;
		screen1_output_scan      = <0>;
		screen1_output_aspect_ratio = <8>;

		dev0_output_type         = <1>;
		dev0_output_mode         = <4>;
		dev0_screen_id           = <0>;
		dev0_do_hpd              = <0>;

		dev1_output_type         = <4>;
		dev1_output_mode         = <10>;
		dev1_screen_id           = <1>;
		dev1_do_hpd              = <1>;

		def_output_dev           = <0>;
		// hdmi_mode_check          = <1>;

		fb0_format               = <0>;
		// fb0_pixel_sequence       = <0>;
		fb0_width                = <0>;
		fb0_height               = <0>;

		fb1_format               = <0>;
		// fb1_pixel_sequence       = <0>;
		fb1_width                = <0>;
		fb1_height               = <0>;
		chn_cfg_mode             = <1>;

		disp_para_zone           = <1>;
		/*VCC-LCD*/
		// dc1sw-supply = <&reg_dc1sw>;
		/*VCC-DSI*/
		// eldo3-supply = <&reg_eldo3>;
		/*VCC-PD*/
		dcdc1-supply = <&reg_dcdc1>;
		/*VCC-LVDS*/
		eldo1-supply = <&reg_eldo1>;

	};

a133_lcd_绿屏_kernel_log

Ａ133点一个RGB　18bit的LCD, 屏亮了，
但是一开机内核开始就是全绿屏，
黑色部分全是显示绿色，
之前看有人遇到是ＩＯ复用了，
gpio的引脚也确认过没有复用的，
ＬＣＤ配置也尝试过改了很多，一点变化都没有，
大家有没有遇到过的情况，上有传log和lcd配置，帮忙看看，万分感谢！！！