求各位大佬帮帮忙！
Y
yyyyppppp 发布的最佳帖子
yyyyppppp 发布的最新帖子
-
t113-s3更换spi nand flash芯片烧录报错？发布在 其它全志芯片讨论区
之前板子用的MX35LF1GE4AB 的spi nand flash 128MB，现在更换为FM25S01BI3 256MB 。
在lichee/linux-5.4/drivers/mtd/awnand/spinand/physic/id.c中 添加了芯片信息。```236 { /FM25S01BI3-DND-A-G3/ 237 .Model = "FM25S01BI3", 238 .NandID = {0xa1, 0xd4, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff}, 239 .DieCntPerChip = 1, 240 .SectCntPerPage = 4, 241 .PageCntPerBlk = 64, 242 .BlkCntPerDie = 2048, 243 .OobSizePerPage = 64, 244 .OperationOpt = SPINAND_QUAD_READ | SPINAND_QUAD_PROGRAM | 245 SPINAND_DUAL_READ | SPINAND_QUAD_NO_NEED_ENABLE, 246 .MaxEraseTimes = 65000, 247 .EccType = BIT2_LIMIT1_ERR2, 248 .EccProtectedType = SIZE16_OFF0_LEN16, 249 .BadBlockFlag = BAD_BLK_FLAG_FIRST_2_PAGE, 250 },之后用PhoenixSuit.exe工具烧录 报错误 错误信息如下：
[02.984]CPU: Allwinner Family [02.987]Model: sun8iw20 I2C: FDT ERROR:fdt_set_all_pin:[twi0]-->FDT_ERR_BADPATH FDT ERROR:fdt_set_all_pin:[twi1]-->FDT_ERR_BADPATH ready [03.009]DRAM: 128 MiB [03.012]Relocation Offset is: 04ede000 [03.034]secure enable bit: 0 [03.037]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz [03.043]gic: normal mode [03.045]flash init start [03.048]workmode = 16,storage type = 0 try card 2 set card number 2 get card number 2 [03.055][mmc]: mmc driver ver uboot2018:2021-11-19 15:38:00 [03.062][mmc]: Is not Boot mode! [03.065][mmc]: SUNXI SDMMC Controller Version:0x50310 [03.076][mmc]: ************Try SD card 2************ [03.081][mmc]: mmc 2 cmd timeout 100 status 100 [03.085][mmc]: smc 2 err, cmd 8, RTO [03.089][mmc]: mmc 2 close bus gating and reset [03.094][mmc]: mmc 2 cmd timeout 100 status 100 [03.098][mmc]: smc 2 err, cmd 55, RTO [03.101][mmc]: mmc 2 close bus gating and reset [03.106][mmc]: ************Try MMC card 2************ [03.115][mmc]: mmc 2 cmd timeout 100 status 100 [03.119][mmc]: smc 2 err, cmd 1, RTO [03.122][mmc]: mmc 2 close bus gating and reset [03.126][mmc]: Card did not respond to voltage select! [03.131][mmc]: ************SD/MMC 2 init error!************ [03.136][mmc]: mmc init product failed MMC init failed try emmc fail [03.143]sunxi-spinand: AW SPINand MTD Layer Version: 1.5 20200407 [03.149]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.9 20200306 [03.157]sunxi-spinand-phy: request spi0 gpio ok [03.161]sunxi-spinand-phy: request general tx dma channel ok! [03.166]sunxi-spinand-phy: request general rx dma channel ok! [03.172]sunxi-spinand-phy: set spic0 clk to 20 Mhz [03.176]sunxi-spinand-phy: init spic0 clk ok sspi->base_addr = 0x4025000, the SPI control register: [VER] 0x4025000 = 0x00010001, [GCR] 0x4025004 = 0x00000083, [TCR] 0x4025008 = 0x00000184 [ICR] 0x4025010 = 0x00000f00, [ISR] 0x4025014 = 0x00000032, [FCR] 0x4025018 = 0x00200020 [FSR] 0x402501c = 0x00000000, [WCR] 0x4025020 = 0x00000000, [CCR] 0x4025024 = 0x00000002 [SDC] 0x4025028 = 0x00002000, [BCR] 0x4025030 = 0x00000000, [TCR] 0x4025034 = 0x00000000 [BCC] 0x4025038 = 0x00000000, [DMA] 0x4025088 = 0x000000e5 [03.222]sunxi-spinand-phy: not detect any munufacture from id table [03.228]sunxi-spinand-phy: get spi-nand Model from fdt fail [03.233]sunxi-spinand-phy: get phy info from fdt fail [03.238]sunxi-spinand-phy: not detect munufacture from fdt [03.243]sunxi-spinand-phy: detect munufacture from id table: FM [03.249]sunxi-spinand-phy: detect spinand id: ffffd4a1 ffffffff [03.254]sunxi-spinand-phy: ========== arch info ========== [03.259]sunxi-spinand-phy: Model: FM25S01BI3 [03.265]sunxi-spinand-phy: Munufacture: FM [03.269]sunxi-spinand-phy: DieCntPerChip: 1 [03.274]sunxi-spinand-phy: BlkCntPerDie: 2048 [03.278]sunxi-spinand-phy: PageCntPerBlk: 64 [03.283]sunxi-spinand-phy: SectCntPerPage: 4 [03.287]sunxi-spinand-phy: OobSizePerPage: 64 [03.292]sunxi-spinand-phy: BadBlockFlag: 0x1 [03.296]sunxi-spinand-phy: OperationOpt: 0xf [03.301]sunxi-spinand-phy: MaxEraseTimes: 65000 [03.306]sunxi-spinand-phy: EccFlag: 0x0 [03.310]sunxi-spinand-phy: EccType: 2 [03.315]sunxi-spinand-phy: EccProtectedType: 1 [03.319]sunxi-spinand-phy: ======================================== [03.325]sunxi-spinand-phy: [03.328]sunxi-spinand-phy: ========== physical info ========== [03.333]sunxi-spinand-phy: TotalSize: 256 M [03.337]sunxi-spinand-phy: SectorSize: 512 B [03.341]sunxi-spinand-phy: PageSize: 2 K [03.345]sunxi-spinand-phy: BlockSize: 128 K [03.350]sunxi-spinand-phy: OOBSize: 64 B [03.354]sunxi-spinand-phy: ======================================== [03.360]sunxi-spinand-phy: [03.362]sunxi-spinand-phy: ========== logical info ========== [03.368]sunxi-spinand-phy: TotalSize: 256 M [03.372]sunxi-spinand-phy: SectorSize: 512 B [03.376]sunxi-spinand-phy: PageSize: 4 K [03.380]sunxi-spinand-phy: BlockSize: 256 K [03.384]sunxi-spinand-phy: OOBSize: 128 B [03.388]sunxi-spinand-phy: ======================================== [03.395]sunxi-spinand-phy: FM25S01BI3 reset rx bit width to 1 [03.400]sunxi-spinand-phy: FM25S01BI3 reset tx bit width to 1 [03.405]sunxi-spinand-phy: set spic0 clk to 100 Mhz [03.410]sunxi-spinand-phy: block lock register: 0x00 [03.415]sunxi-spinand-phy: feature register: 0x10 [03.419]sunxi-spinand-phy: sunxi physic nand init end [03.424]Loading Environment from SUNXI_FLASH... OK [03.428]try to burn key [03.431]out of usb burn from boot: not need burn key Hit any key to stop autoboot: 0 sunxi work mode=0x10 run usb efex buf queue page size = 16384 delay time 2500 weak:otg_phy_config usb init ok set address 0x2 set address 0x2 ok set address 0x2 set address 0x2 ok SUNXI_EFEX_ERASE_TAG erase_flag = 0x12 origin_erase_flag = 0x1 FEX_CMD_fes_verify_status FEX_CMD_fes_verify last err=0 SUNXI_EFEX_EXT4_UBIFS_TAG & do nothing the 0 mbr table is ok the 1 mbr table is ok the 2 mbr table is ok the 3 mbr table is ok *************MBR DUMP*************** total mbr part 6 part[0] name :boot-resource part[0] classname :DISK part[0] addrlo :0x8000 part[0] lenlo :0x1a00 part[0] user_type :32768 part[0] keydata :0 part[0] ro :0 part[1] name :env part[1] classname :DISK part[1] addrlo :0x9a00 part[1] lenlo :0x1f8 part[1] user_type :32768 part[1] keydata :0 part[1] ro :0 part[2] name :env-redund part[2] classname :DISK part[2] addrlo :0x9bf8 part[2] lenlo :0x1f8 part[2] user_type :32768 part[2] keydata :0 part[2] ro :0 part[3] name :boot part[3] classname :DISK part[3] addrlo :0x9df0 part[3] lenlo :0x2000 part[3] user_type :32768 part[3] keydata :0 part[3] ro :0 part[4] name :rootfs part[4] classname :DISK part[4] addrlo :0xbdf0 part[4] lenlo :0x2d400 part[4] user_type :32768 part[4] keydata :0 part[4] ro :0 part[5] name :UDISK part[5] classname :DISK part[5] addrlo :0x391f0 part[5] lenlo :0x0 part[5] user_type :0 part[5] keydata :0 part[5] ro :0 total part: 7 mbr 0, 8000, 8000 boot-resource 1, 1a00, 8000 env 2, 1f8, 8000 env-redund 3, 1f8, 8000 boot 4, 2000, 8000 rootfs 5, 2d400, 8000 UDISK 6, 0, 0 [06.731]erase blk 0 to blk 32 need erase flash: 18 [06.793]mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys) device nand0 <nand>, # parts = 4 #: name size offset mask_flags 0: boot0 0x00100000 0x00000000 1 1: uboot 0x00300000 0x00100000 1 2: secure_storage 0x00100000 0x00400000 1 3: sys 0x0fb00000 0x00500000 0 active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000 defaults: mtdids : nand0=nand mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys) [06.844]MTD info (4) [06.846]pagesize: 0x1000 [06.848]blksize: 0x40000 [06.850]num offset bytes name [06.854]0 0x00000000 0x00100000 boot0 [06.857]1 0x00100000 0x00300000 uboot [06.861]2 0x00400000 0x00100000 secure_storage [06.865]3 0x00500000 0x0fb00000 sys [06.869]ubi attach the last part of mtd device: NO.3 [07.057]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.061]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.066]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.071]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.075]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.080]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.084]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.089]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.094]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.098]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.103]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.107]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.112]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.117]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.121]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.126]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.130]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.135]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.139]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.144]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.149]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.153]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.158]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.162]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.167]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.172]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.176]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.181]sunxi-spinand-phy: [SPINAND]: ecc error 0x2 [07.185]sunxi-spinand-phy: [SPINAND]: ecc error 0x2请问各位大佬如何解决！！！！！！
-
100ASK_T113-Pro如何通过擦除分区来升级uboot、kernel、rootfs?发布在 其它全志芯片讨论区
不使用PhoenixSuit.exe 通过网口telnet登录 输入擦除命令来升级uboot、kenel、rootfs?
-
t113-S3 pro 100ask开发板如何通过命令flash-erase烧录 uboot、kerne了？发布在 其它全志芯片讨论区
不想通过PhoenixSuit.exe烧写镜像 而且韦东山老师提供的fastboot也用不了 因为是自己公司设计的板子 想进入开发板系统后通过命令升级 uboot kernel. 求助各位大佬！！！
-
t113移植FT5446触摸驱动报错？发布在 其它全志芯片讨论区
insmod focaltech_ts.ko 报错
报错日志
root@(none):/# insmod focaltech_ts.ko
[ 45.327665] input: fts_ts as /devices/platform/soc@3000000/sunxi-i2c2/i2c-2/2-0038/input/input1
[ 45.377656] fts_ts 2-0038: 2-0038 supply not found, using dummy regulator
[ 45.385569] fts_ts 2-0038: 2-0038 supply not found, using dummy regulator
[ 45.407580] debugfs: Directory '2-0038-' with parent 'reg-dummy-regulator-dummy' already present!
请问是什么原因？ -
Avaota - A1 t527只能用TF卡旺开发板烧写镜像吗？不能像t113用一样的PhoenixSuit.exe吗？发布在 T527系列-工业车载
Avaota - A1 t527只能用TF卡旺开发板烧写镜像吗？不能像t113用一样的PhoenixSuit.exe吗？