已经解决了
wlan_regon是这个引脚我给他配置成了低电平有效导致的

[bluetooth]# power on
No default controller available
[bluetooth]# exit
root@T113i-RockEnergy:~/tool_script# hciconfig
hci0: Type: Primary Bus: UART
BD Address: E2:22:B7:4C:2A:E1 ACL MTU: 1021:8 SCO MTU: 0:0
UP RUNNING PSCAN
RX bytes:633 acl:0 sco:0 events:35 errors:0
TX bytes:964 acl:0 sco:0 commands:35 errors:0

如题，在Bluetoothctl的终端交互中提示No default controller available。
这是个什么原因呢

已经解决了
wlan_regon是这个引脚我给他配置成了低电平有效导致的

回复: T113 xr829模块wifi使用sdc0初始化报错
大佬是否解决了 我也遇到这样的问题

[ 20.101775] 001: ======== XRADIO WIFI OPEN ========
[ 20.102410] 001: [XRADIO] Driver Label:XR_V02.16.88_P2P_HT40_01.31
[ 20.102465] 001: [XRADIO] Allocated hw_priv @ 5637e7ba
[ 20.108843] 000: yyxradio_wlan_power: on = 1
[ 20.108865] 000: sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
[ 20.118910] 000: sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
[ 20.318976] 000: [XRADIO] Detect SDIO card 1
[ 20.319044] 000: sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
[ 20.319082] 000: sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
[ 20.319128] 000: sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
[ 20.319156] 000: sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
[ 20.319378] 000: mmc1: card 0001 removed
[ 20.319503] 000: sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 20.320905] 000: sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 20.321004] 000: sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[ 20.333584] 000: sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 20.346910] 000: sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 20.347757] 000: sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 20.347782] 000: sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 20.350791] 000: sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 20.352930] 000: sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 20.353763] 000: sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 20.354591] 000: sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 20.355415] 000: sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 20.355442] 000: sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 22.406105] 000: yywlan power down
[ 22.406117] 000: yyxradio_wlan_power: on = 0
[ 22.406145] 000: sunxi-rfkill soc@3000000:rfkill@0: wlan power off success
[ 22.506543] 000: [XRADIO] Remove SDIO card 1
[ 22.506587] 000: sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 22.506703] 000: sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[ 22.516726] 000: [SBUS_ERR] sdio probe timeout!
[ 22.516736] 000: [XRADIO_ERR] sbus_sdio_init failed
[ 22.516740] 000: yy3: goto err1 - sbus_sdio_init fail
[ 22.516742] 000: yy19: entering err1
[ 22.517137] 000: yy20: return final err=-110
[ 22.517146] 000: yyyxradio_core_init failed1 (-110)!
[ 22.519271] 000: sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 22.532566] 000: sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 22.535584] 000: sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 22.546241] 000: sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[ 22.546337] 000: sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[ 22.546470] 000: sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[ 22.547370] 000: mmc1: new high speed SDIO card at address 0001
insmod: ERROR: could not insert module /lib/modules/5.4.61-rt37-g01fdce3-dirty/xr829.ko: Connection timed out

现在打印信息是这样了

@shuaige 在 t113i启动异常 中说：

@yyh5961 之前在其他平台遇到过，是编译出来的kernel镜像有问题

对的 是我改动的地方错了，我是在device/product/configs/xxx/这个下面修改的，然后实际上得在xxx/buildroot/这下面修改才有效果 这下面优先级更高

root@T113i-RockEnergy:/# insmod ./lib/modules/5.4.61-rt37-g01fdce3-dirty/xr829.ko
[ 651.793302] 000: ======== XRADIO WIFI OPEN ========
[ 651.793924] 000: [XRADIO] Driver Label:XR_V02.16.88_P2P_HT40_01.31
[ 651.793982] 000: [XRADIO] Allocated hw_priv @ d0eaa08f
[ 651.800459] 001: sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
[ 651.810508] 001: sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
[ 652.010539] 001: sunxi_hosts[1] should not be null
[ 652.010543] 001: [XRADIO] Detect SDIO card 1
[ 654.088952] 001: sunxi-rfkill soc@3000000:rfkill@0: wlan power off success
[ 654.189256] 001: sunxi_hosts[1] should not be null
[ 654.189258] 001: [XRADIO] Remove SDIO card 1
[ 654.199269] 001: [SBUS_ERR] sdio probe timeout!
[ 654.199277] 001: [XRADIO_ERR] sbus_sdio_init failed
[ 654.199664] 001: xradio_core_init failed (-110)!
insmod: ERROR: could not insert module ./lib/modules/5.4.61-rt37-g01fdce3-dirty/xr829.ko: Connection timed out

老哥们 为什么这个这个sdio被移除了啊

@lipeitong 问题解决了吗 大佬

回复: 全志芯片Tina Linux 修改 UART 引脚、UART端口

照这个帖子修改了，现在板子上电后只打印这么点内容，uboot也只有在烧写的时候才打印，内核都没有打印信息，有没有大哥知道这是什么情况呢

@qq354813374
你这最后咋改的

回复: t113i修改调试串口到uart3

[158]HELLO! BOOT0 is starting!
[160]BOOT0 commit : 069ed30b88
M/TC: OP-TEE version: 2a99a16f (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Thu Aug 17 11:13:02 UTC 2023 arm
E/TC:0 0 platform_standby_fdt_parse:126 no pmu0 node
E/TC:0 0 sunxi_twi_parse_from_dt:121 no pmu node
E/TC:0 fdt_getprop_u32:336 prop trace_level not found
[00.923]yysunxi bmp info error : unable to open logo file bootlogo.bmp
[01.522]no vendor_boot partition is found
[01.551]Starting kernel ...
上电之后一点打印信息都没有 不知道哪个地方把uboot输出关了