水一下，需要拉sdk下载

需要LV2，不然下载不了sdk，有点麻烦

我的也扫不到wifi，但是可以扫到路由器的wifi

D1-H烧录出现问题，使用的固件是：

固件烧录过程中的日志如下：

[663]fes begin commit:43b0f57
[666]set pll start
[668]periph0 has been enabled
[670]set pll end
[749][pmu]: bus read error
[752]board init ok
[754]beign to init dram
[756]DRAM only have internal ZQ!!
[759]get_pmu_exist() = -1
[761]ddr_efuse_type: 0x0
[764][AUTO DEBUG] two rank and full DQ!
[768]ddr_efuse_type: 0x0
[771][AUTO DEBUG] rank 0 row = 15
[774][AUTO DEBUG] rank 0 bank = 8
[777][AUTO DEBUG] rank 0 page size = 2 KB
[781][AUTO DEBUG] rank 1 row = 15
[784][AUTO DEBUG] rank 1 bank = 8
[788][AUTO DEBUG] rank 1 page size = 2 KB
[791]rank1 config same as rank0
[794]DRAM BOOT DRIVE INFO: V0.24
[797]DRAM CLK = 792 MHz
[799]DRAM Type = 3 (2:DDR2,3:DDR3)
[803]DRAMC ZQ value: 0x7b7bfb
[805]DRAM ODT value: 0x42.
[808]ddr_efuse_type: 0x0
[811]DRAM SIZE =1024 M
[814]DRAM simple test OK.
[817]init dram ok


U-Boot 2018.05-gaf9d250 (Apr 14 2021 - 01:55:48 +0000) Allwinner Technology

[03.405]DRAM:  512 MiB
[03.409]Relocation Offset is: 1def0000
[03.432]secure enable bit: 0
[03.436]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
[03.442]flash init start
[03.444]workmode = 16,storage type = 0
try card 2
set card number 2
get card number 2
[03.452][mmc]: mmc driver ver uboot2018:2021-03-16 11:23:00-1
[03.461][mmc]: get sdc_type fail and use default host:tm4.
[03.485][mmc]: Is not Boot mode!
[03.488][mmc]: SUNXI SDMMC Controller Version:0x50310
[03.499][mmc]: ************Try SD card 2************
[03.504][mmc]: mmc 2 cmd timeout 100 status 100
[03.508][mmc]: smc 2 err, cmd 8,  RTO
[03.512][mmc]: mmc 2 close bus gating and reset
[03.517][mmc]: mmc 2 cmd timeout 100 status 100
[03.521][mmc]: smc 2 err, cmd 55,  RTO
[03.524][mmc]: mmc 2 close bus gating and reset
[03.529][mmc]: ************Try MMC card 2************
[03.755][mmc]: mmc 2 cmd timeout 100 status 100
[03.759][mmc]: smc 2 err, cmd 8,  RTO
[03.762][mmc]: mmc 2 close bus gating and reset
[03.768][mmc]: mmc 2 cmd timeout 100 status 100
[03.772][mmc]: smc 2 err, cmd 55,  RTO
[03.775][mmc]: mmc 2 close bus gating and reset
[03.792][mmc]: gen_tuning_blk_bus8: total blk 10
[03.796][mmc]: gen_tuning_blk_bus4: total blk 6
[03.801][mmc]: Using 4 bit tuning now
[03.805][mmc]: write_tuning_try_freq: write ok
[03.810][mmc]: Pattern compare ok
[03.813][mmc]: Write tuning pattern ok
[03.817][mmc]: ================== HSSDR52_SDR25...
[03.821][mmc]: skip freq 400000
[03.824][mmc]: skip freq 25000000
[03.827][mmc]: freq: 2-50000000-64-4
[04.546][mmc]: [0-63|64]
[04.548][mmc]: ================== HSDDR52_DDR50...
[04.552][mmc]: skip freq 400000
[04.555][mmc]: freq: 1-25000000-64-4
[05.208][mmc]: freq: 2-50000000-64-4
[05.800][mmc]: [0-58|59]
[05.802][mmc]: [0-58|59]
[05.804][mmc]: DS26/SDR12: 0xffffffff 0xffffffff
[05.809][mmc]: HSSDR52/SDR25: 0xff20ffff 0xffffffff
[05.813][mmc]: HSDDR52/DDR50: 0xff1d1dff 0xffffffff
[05.818][mmc]: HS200/SDR104: 0xffffffff 0xffffffff
[05.822][mmc]: HS400: 0xffffffff 0xffffffff
[05.826][mmc]: HS400: 0xffffffff 0xffffffff
[05.830][mmc]: Best spd md: 2-HSDDR52/DDR50, freq: 2-50000000, Bus width: 4
[05.841]Loading Environment from SUNXI_FLASH... OK
[05.848]try to burn key
[05.851]out of usb burn from boot: not boot mode
Hit any key to stop autoboot:  0
sunxi work mode=0x10
run usb efex
delay time 2500
weak:otg_phy_config
usb init ok
set address 0x20
set address 0x20 ok
SUNXI_EFEX_ERASE_TAG
erase_flag = 0x12
origin_erase_flag = 0x1
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
the 0 mbr table is ok
the 1 mbr table is ok
the 2 mbr table is ok
the 3 mbr table is ok
*************MBR DUMP***************
total mbr part 8

part[0] name      :boot-resource
part[0] classname :DISK
part[0] addrlo    :0x1f8
part[0] lenlo     :0x1f8
part[0] user_type :32768
part[0] keydata   :0
part[0] ro        :0

part[1] name      :env
part[1] classname :DISK
part[1] addrlo    :0x3f0
part[1] lenlo     :0x1f8
part[1] user_type :32768
part[1] keydata   :0
part[1] ro        :0

part[2] name      :env-redund
part[2] classname :DISK
part[2] addrlo    :0x5e8
part[2] lenlo     :0x1f8
part[2] user_type :32768
part[2] keydata   :0
part[2] ro        :0

part[3] name      :boot
part[3] classname :DISK
part[3] addrlo    :0x7e0
part[3] lenlo     :0x50b8
part[3] user_type :32768
part[3] keydata   :0
part[3] ro        :0

part[4] name      :rootfs
part[4] classname :DISK
part[4] addrlo    :0x5898
part[4] lenlo     :0xc8d0
part[4] user_type :32768
part[4] keydata   :0
part[4] ro        :0

part[5] name      :dsp0
part[5] classname :DISK
part[5] addrlo    :0x12168
part[5] lenlo     :0x1f8
part[5] user_type :32768
part[5] keydata   :0
part[5] ro        :0

part[6] name      :recovery
part[6] classname :DISK
part[6] addrlo    :0x12360
part[6] lenlo     :0x6e40
part[6] user_type :32768
part[6] keydata   :0
part[6] ro        :0

part[7] name      :UDISK
part[7] classname :DISK
part[7] addrlo    :0x191a0
part[7] lenlo     :0x0
part[7] user_type :0
part[7] keydata   :0
part[7] ro        :0

total part: 9
mbr 0, 1f8, 8000
boot-resource 1, 1f8, 8000
env 2, 1f8, 8000
env-redund 3, 1f8, 8000
boot 4, 50b8, 8000
rootfs 5, c8d0, 8000
dsp0 6, 1f8, 8000
recovery 7, 6e40, 8000
UDISK 8, 0, 0
[08.862]erase all part start
need erase flash: 18
[08.867][mmc]: erase from: 0, to: 30535679, cnt: 30535680, erase_group: 1024
[08.902][mmc]: sunxi_mmc_do_send_cmd_common: cmd 38 wait rsp busy 0x1c ms
[08.908]read item0 copy0
[08.911][mmc]: memalign dst_align is NULL!
read first backup failed in fun sunxi_sprite_mmc_secread line 443
[08.920][mmc]: memalign dst_align is NULL!
read first backup failed in fun sunxi_sprite_mmc_secread line 443
[08.930]unknown error happen in item 0 read
[08.934]get secure storage map err
[08.937][mmc]: memalign src_align is NULL!
write first backup failed in fun sunxi_sprite_mmc_secwrite line 508
[08.947]erase secure storage block 0 err
SUNXI_EFEX_MBR_TAG
mbr size = 0x10000
write primary GPT success
write Backup GPT success
[08.964]update partition map
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
******Has init
FEX_CMD_fes_verify_value, start 0x1f8, size high 0x0:low 0x14000
FEX_CMD_fes_verify_value 0xe6f75b5c
FEX_CMD_fes_verify_value, start 0x3f0, size high 0x0:low 0x20000
FEX_CMD_fes_verify_value 0x4b1dbffb
FEX_CMD_fes_verify_value, start 0x5e8, size high 0x0:low 0x20000
FEX_CMD_fes_verify_value 0x4b1dbffb
FEX_CMD_fes_verify_value, start 0x7e0, size high 0x0:low 0x8ea000
FEX_CMD_fes_verify_value 0xc78c66c
FEX_CMD_fes_verify_value, start 0x5898, size high 0x0:low 0x18e0000
FEX_CMD_fes_verify_value 0xc00f4db8
FEX_CMD_fes_verify_value, start 0x12168, size high 0x0:low 0x3dc20
FEX_CMD_fes_verify_value 0x84b70c5a
bootfile_mode=4
SUNXI_EFEX_BOOT1_TAG
boot1 size = 0xfc000, max size = 0x200000
uboot size = 0xfc000
storage type = 2
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
bootfile_mode=4
SUNXI_EFEX_BOOT0_TAG
boot0 size = 0x10000
[13.987][mmc]: write mmc 2 info ok
dram para[0] = 318
dram para[1] = 3
dram para[2] = 7b7bfb
dram para[3] = 1
dram para[4] = 10f210f2
dram para[5] = 4001000
dram para[6] = 1c70
dram para[7] = 42
dram para[8] = 18
dram para[9] = 0
dram para[10] = 4a2195
dram para[11] = 2423190
dram para[12] = 8b061
dram para[13] = b4787896
dram para[14] = 0
dram para[15] = 48484848
dram para[16] = 48
dram para[17] = 1620121e
dram para[18] = 0
dram para[19] = 0
dram para[20] = 0
dram para[21] = 870000
dram para[22] = 24
dram para[23] = b4056103
dram para[24] = 0
dram para[25] = 0
dram para[26] = 0
dram para[27] = 0
dram para[28] = 0
dram para[29] = 0
dram para[30] = 0
dram para[31] = 0
storage type = 2
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
sunxi_efex_next_action=2
exit usb
next work 2
▒[41]HELLO! BOOT0 is starting!T
[44]BOOT0 commit : 43b0f57
[46]set pll start
[48]periph0 has been enabled
[51]set pll end
[130][pmu]: bus read error
[132]board init ok
[134]DRAM only have internal ZQ!!
[137]get_pmu_exist() = -1
[140]DRAM BOOT DRIVE INFO: V0.24
[143]DRAM CLK = 792 MHz
[145]DRAM Type = 3 (2:DDR2,3:DDR3)
[148]DRAMC ZQ value: 0x7b7bfb
[151]DRAM ODT value: 0x42.
[154]ddr_efuse_type: 0x0
[157]DRAM SIZE =1024 M
[160]DRAM simple test OK.
[162]dram size =1024
[164]card no is 2
[166]sdcard 2 line count 8
[169][mmc]: mmc driver ver 2021-04-2 16:45
[172][mmc]: n8
[179][mmc]: Wrong media type 0x0, but host sdc2, try mmc first
[185][mmc]: ***Try MMC card 2***
[192][mmc]: mmc 2 cmd 1 timeout, err 100
[196][mmc]: mmc 2 cmd 1 err 100
[198][mmc]: mmc 2 send op cond failed
[202][mmc]: MMC card 2 Card did not respond to voltage select!
[208][mmc]: ***SD/MMC 2 init error!!!***
[215][mmc]: ***Try SD card 2***
[218][mmc]: mmc 2 cmd 8 timeout, err 100
[222][mmc]: mmc 2 cmd 8 err 100
[225][mmc]: mmc 2 send if cond failed
[229][mmc]: mmc 2 cmd 55 timeout, err 100
[233][mmc]: mmc 2 cmd 55 err 100
[236][mmc]: mmc 2 send app cmd failed
[240][mmc]: SD card 2 Card did not respond to voltage select!
[245][mmc]: ***SD/MMC 2 init error!!!***
[249][mmc]: mmc 2 register failed
[252]Loading boot-pkg fail(error=2)

请大家多多帮忙看一下，麻烦大家了

我跟随官方教程进行了sdk 的编译，得到的文件如下

随后，我将红框中的img文件使用PhoenixSuit进行烧录

烧录后启动D1-H板子，得到的结果如下图：

无法进入tina linux系统，请问大家这种情况如何解决！非常感谢

需要LV2，不然下载不了sdk，有点麻烦

水一下，需要拉sdk下载