@whycan 感谢大神，确实是串口问题！
C
ccl_550427288 发布的帖子
-
回复: F133进不了系统发布在 D1系列-RISC-V
@whycan 换了3张卡了，但很奇怪屏幕有显示，但是进不了系统。
截图)[292]HELLO! BOOT0 is starting! [295]BOOT0 commit : 27369ab [297]set pll start [299]periph0 has been enabled [302]set pll end [304][pmu]: bus read error [306]board init ok [308]ZQ value = 0x2f*********** [311]get_pmu_exist() = -1 [314]ddr_efuse_type: 0xa [316][AUTO DEBUG] single rank and full DQ! [320]ddr_efuse_type: 0xa [323][AUTO DEBUG] rank 0 row = 13 [326][AUTO DEBUG] rank 0 bank = 4 [330][AUTO DEBUG] rank 0 page size = 2 KB [333]DRAM BOOT DRIVE INFO: V0.24 [336]DRAM CLK = 528 MHz [339]DRAM Type = 2 (2:DDR2,3:DDR3) [342]DRAMC read ODT off. [344]DRAM ODT off. [346]ddr_efuse_type: 0xa [349]DRAM SIZE =64 M [353]DRAM simple test OK. [355]dram size =64 [357]card no is 0 [359]sdcard 0 line count 4 [361][mmc]: mmc driver ver 2021-04-2 16:45 [370][mmc]: Wrong media type 0x0 [373][mmc]: ***Try SD card 0*** [384][mmc]: HSSDR52/SDR25 4 bit [387][mmc]: 50000000 Hz [389][mmc]: 476 MB [391][mmc]: ***SD/MMC 0 init OK!!!*** [445]Loading boot-pkg Succeed(index=0). [449]Entry_name = opensbi [452]Entry_name = u-boot [456]Entry_name = dtb [458]mmc not para [460]Jump to second Boot. OpenSBI v0.6 ____ _____ ____ _____ / __ \ / ____| _ \_ _| | | | |_ __ ___ _ __ | (___ | |_) || | | | | | '_ \ / _ \ '_ \ \___ \| _ < | | | |__| | |_) | __/ | | |____) | |_) || |_ \____/| .__/ \___|_| |_|_____/|____/_____| | | |_| Platform Name : T-HEAD Xuantie Platform Platform HART Features : RV64ACDFIMSUVX Platform Max HARTs : 1 Current Hart : 0 Firmware Base : 0x40000400 Firmware Size : 75 KB Runtime SBI Version : 0.2 MIDELEG : 0x0000000000000222 MEDELEG : 0x000000000000b1ff PMP0 : 0x0000000040000000-0x000000004001ffff (A) PMP1 : 0x0000000040000000-0x000000007fffffff (A,R,W,X) PMP2 : 0x0000000080000000-0x00000000bfffffff (A,R,W,X) PMP3 : 0x0000000000020000-0x0000000000027fff (A, U-Boot 2018.05-g0a88ac9-dirty (Sep 03 2021 - 21:30:18 +0800) Allwinner Technology [00.543]DRAM: 64 MiB [00.545]Relocation Offset is: 01ef0000 [00.550]secure enable bit: 0 [00.552]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz [00.558]flash init start [00.561]workmode = 0,storage type = 1 [00.564][mmc]: mmc driver ver uboot2018:2021-04-16 14:23:00-1 [00.570][mmc]: get sdc_type fail and use default host:tm1. [00.576][mmc]: can't find node "mmc0",will add new node [00.581][mmc]: fdt err returned <no error> [00.585][mmc]: Using default timing para [00.588][mmc]: SUNXI SDMMC Controller Version:0x50310 [00.607][mmc]: card_caps:0x3000000a [00.611][mmc]: host_caps:0x3000003f [00.614]sunxi flash init ok [00.616]line:714 init_clocks __clk_init: clk pll_periph0x2 already initialized register fix_factor clk error [00.627]drv_disp_init fdt_getprop_u32 s_pwm.pwm-base fail [00.642]drv_disp_init finish [00.645]boot_gui_init:start [00.648]set disp.dev2_output_type fail. using defval=0 [00.654]boot_gui_init:finish sunxi_partition_get_partno_byname: try part 1, ret = 0 sunxi_partition_get_partno_byname: try part 2, ret = 0 sunxi_partition_get_partno_byname: try part 3, ret = 0 sunxi_partition_get_partno_byname: try part 4, ret = 0 sunxi_partition_get_partno_byname: try part 5, ret = 0 sunxi_partition_get_partno_byname: try part 6, ret = 0 sunxi_partition_get_partno_byname: try part 7, ret = 0 sunxi_partition_get_partno_byname: try part 8, ret = 0 sunxi_partition_get_partno_byname: try part 9, ret = -1 partno erro : can't find partition bootloader sunxi_partition_get_partno_byname: try part 1, ret = 0 54 bytes read in 1 ms (52.7 KiB/s) [00.721]bmp_name=bootlogo.bmp size 307254 307254 bytes read in 16 ms (18.3 MiB/s) [00.758]Loading Environment from SUNXI_FLASH... OK [00.779]out of usb burn from boot: not need burn key root_partition is rootfs set root to /dev/mmcblk0p5 [00.789]update part info [00.792]update bootcmd [00.795]change working_fdt 0x42aafda8 to 0x42a8fda8 [00.816]update dts Hit any key to stop autoboot: 0 [00.834]LCD open finish Android's image name: d1-nezha No reserved memory region found in source FDT [01.302] Starting kernel ... [01.305][mmc]: MMC Device 2 not found [01.308][mmc]: mmc 2 not find, so not exit [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000 [ 0.000000] Linux version 5.4.61 (cube@ubuntu) (riscv64-unknown-linux-gnu-gcc (C-SKY RISCV Tools V1.8.4 B20200702) 8.1.0, GNU ld (GNU Binutils) 2.32) #60 PREEMPT Fri Sep 3 23:03:41 UTC 2021 [ 0.000000] cma: Reserved 8 MiB at 0x0000000043800000 [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000040200000-0x0000000043ffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040200000-0x0000000043ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x0000000043ffffff] [ 0.000000] On node 0 totalpages: 15872 [ 0.000000] DMA32 zone: 217 pages used for memmap [ 0.000000] DMA32 zone: 0 pages reserved [ 0.000000] DMA32 zone: 15872 pages, LIFO batch:3 [ 0.000000] elf_hwcap is 0x20112d [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 15655 [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p5 init=/sbin/init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:dsp0@mmcblk0p6:recovery@mmcblk0p7:UDISK@mmcblk0p8 cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun20iw1p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.05-g0a88ac9-dirty(09/03/2021-21:30:18) mbr_off [ 0.000000] Dentry cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.000000] Sorting __ex_table... [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 42224K/63488K available (6067K kernel code, 663K rwdata, 2093K rodata, 192K init, 254K bss, 13072K reserved, 8192K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0 [ 0.000000] plic: mapped 200 interrupts with 1 handlers for 2 contexts. [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [0] [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000007] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000029] riscv_timer_clockevent depends on broadcast, but no broadcast function available [ 0.000377] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.001016] Console: colour dummy device 80x25 [ 0.001062] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.001082] pid_max: default: 32768 minimum: 301 [ 0.001299] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.001320] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.003408] ASID allocator initialised with 65536 entries [ 0.003613] rcu: Hierarchical SRCU implementation. [ 0.004367] devtmpfs: initialized [ 0.022389] random: get_random_u32 called from bucket_table_alloc.isra.31+0x4e/0x15e with crng_init=0 [ 0.023360] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.023399] futex hash table entries: 256 (order: 0, 6144 bytes, linear) [ 0.023970] pinctrl core: initialized pinctrl subsystem [ 0.025509] NET: Registered protocol family 16 [ 0.027583] DMA: preallocated 256 KiB pool for atomic allocations [ 0.028339] cpuidle: using governor menu [ 0.061533] rtc_ccu: sunxi ccu init OK [ 0.069736] clock: sunxi ccu init OK [ 0.070943] clock: sunxi ccu init OK [ 0.114418] iommu: Default domain type: Translated [ 0.114628] sunxi iommu: irq = 4 [ 0.115825] SCSI subsystem initialized [ 0.116214] usbcore: registered new interface driver usbfs [ 0.116316] usbcore: registered new interface driver hub [ 0.116459] usbcore: registered new device driver usb [ 0.116687] mc: Linux media interface: v0.10 [ 0.116756] videodev: Linux video capture interface: v2.00 [ 0.118012] sunxi-msgbox-amp 3003000.msgbox: invalid resource [ 0.118776] Advanced Linux Sound Architecture Driver Initialized. [ 0.119486] Bluetooth: Core ver 2.22 [ 0.119587] NET: Registered protocol family 31 [ 0.119600] Bluetooth: HCI device and connection manager initialized [ 0.119629] Bluetooth: HCI socket layer initialized [ 0.119646] Bluetooth: L2CAP socket layer initialized [ 0.119690] Bluetooth: SCO socket layer initialized [ 0.120041] pwm module init! [ 0.121663] g2d 5410000.g2d: Adding to iommu group 0 [ 0.122195] G2D: rcq version initialized.major:250 [ 0.123538] clocksource: Switched to clocksource riscv_clocksource [ 0.137072] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver [ 0.155746] thermal_sys: Registered thermal governor 'step_wise' [ 0.155753] thermal_sys: Registered thermal governor 'user_space' [ 0.156328] NET: Registered protocol family 2 [ 0.157253] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.157304] TCP established hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.157328] TCP bind hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.157343] TCP: Hash tables configured (established 512 bind 512) [ 0.157525] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.157573] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.157837] NET: Registered protocol family 1 [ 0.160534] Initialise system trusted keyrings [ 0.160857] workingset: timestamp_bits=62 max_order=14 bucket_order=0 [ 0.168695] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.189371] Key type asymmetric registered [ 0.189389] Asymmetric key parser 'x509' registered [ 0.189417] io scheduler mq-deadline registered [ 0.189428] io scheduler kyber registered [ 0.189451] atomic64_test: passed [ 0.190750] [DISP]disp_module_init [ 0.191343] disp 5000000.disp: Adding to iommu group 0 [ 0.192002] [DISP] disp_init,line:2385: [ 0.192008] smooth display screen:0 type:1 mode:4 [ 0.221195] disp 5000000.disp: 5000000.disp supply vcc-lcd not found, using dummy regulator [ 0.221488] disp 5000000.disp: 5000000.disp supply vcc-pd not found, using dummy regulator [ 0.234739] [DISP] disp_sys_pwm_request,line:442: [ 0.234746] disp_sys_pwm_request pwm 8 fail! -517 [ 0.234762] [DISP] disp_sys_pwm_config,line:509: [ 0.234766] disp_sys_pwm_Config, handle is NULL! [ 0.235482] display_fb_request,fb_id:0 [ 0.251631] disp_al_manager_apply ouput_type:1 [ 0.251776] [DISP] lcd_clk_config,line:731: [ 0.251791] disp 0, clk: pll(198000000),clk(198000000),dclk(33000000) dsi_rate(198000000) [ 0.251791] clk real:pll(288000000),clk(288000000),dclk(48000000) dsi_rate(0) [ 0.251852] [DISP] disp_sys_gpio_request,line:276: [ 0.251858] disp_sys_gpio_request failed, gpio_name=lcd_bl_en, gpio=123, value=0, ret=-517 [ 0.251873] [DISP] disp_sys_pwm_request,line:442: [ 0.251878] disp_sys_pwm_request pwm 8 fail! -517 [ 0.252461] [DISP]disp_module_init finish [ 0.253313] sunxi_sid_init()506 - insmod ok [ 0.261731] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator [ 0.262367] uart uart0: get regulator failed [ 0.262400] uart uart0: uart0 supply uart not found, using dummy regulator [ 0.262824] uart0: ttyS0 at MMIO 0x2500000 (irq = 18, base_baud = 1500000) is a SUNXI [ 0.262856] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n [ 1.066960] printk: console [ttyS0] enabled [ 1.072806] misc dump reg init [ 1.078664] libphy: Fixed MDIO Bus: probed [ 1.083284] CAN device driver interface [ 1.087966] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.095395] sunxi-ehci: EHCI SUNXI driver [ 1.100413] get ehci0-controller wakeup-source is fail. [ 1.106505] sunxi ehci0-controller don't init wakeup source [ 1.112731] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe0008fbb60, 0x:ffffffd00406e000, irq_no:2e [ 1.126305] [sunxi-ehci0]: Not init ehci0 [ 1.131057] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.138093] sunxi-ohci: OHCI SUNXI driver [ 1.143096] get ohci0-controller wakeup-source is fail. [ 1.149155] sunxi ohci0-controller don't init wakeup source [ 1.155427] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe0008fc6a0 [ 1.165886] [sunxi-ohci0]: Not init ohci0 [ 1.170943] usbcore: registered new interface driver uas [ 1.177126] usbcore: registered new interface driver usb-storage [ 1.184025] usbcore: registered new interface driver ums-alauda [ 1.190691] usbcore: registered new interface driver ums-cypress [ 1.197602] usbcore: registered new interface driver ums-datafab [ 1.204437] usbcore: registered new interface driver ums_eneub6250 [ 1.211466] usbcore: registered new interface driver ums-freecom [ 1.218360] usbcore: registered new interface driver ums-isd200 [ 1.225095] usbcore: registered new interface driver ums-jumpshot [ 1.232008] usbcore: registered new interface driver ums-karma [ 1.238656] usbcore: registered new interface driver ums-onetouch [ 1.245664] usbcore: registered new interface driver ums-realtek [ 1.252517] usbcore: registered new interface driver ums-sddr09 [ 1.259282] usbcore: registered new interface driver ums-sddr55 [ 1.266085] usbcore: registered new interface driver ums-usbat [ 1.273366] sunxi_gpadc_init,1968, success [ 1.278828] sunxi-rtc 7090000.rtc: errata__fix_alarm_day_reg_default_value(): ALARM0_DAY_REG=0, set it to 1 [ 1.291254] sunxi-rtc 7090000.rtc: registered as rtc0 [ 1.297060] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:02 UTC (2) [ 1.306058] sunxi-rtc 7090000.rtc: sunxi rtc probed [ 1.311885] i2c /dev entries driver [ 1.315968] IR NEC protocol handler initialized [ 1.321713] sunxi cedar version 1.1 [ 1.325944] sunxi-cedar 1c0e000.ve: Adding to iommu group 0 [ 1.332189] VE: install start!!! [ 1.332189] [ 1.337842] VE: cedar-ve the get irq is 6 [ 1.337842] [ 1.344242] VE: ve_debug_proc_info:(____ptrval____), data:(____ptrval____), lock:(____ptrval____) [ 1.344242] [ 1.355895] VE: install end!!! [ 1.355895] [ 1.362392] sunxi-wdt 6011000.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 1.371584] Bluetooth: HCI UART driver ver 2.3 [ 1.376594] Bluetooth: HCI UART protocol H4 registered [ 1.382351] Bluetooth: HCI UART protocol BCSP registered [ 1.388310] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10 [ 1.398149] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.19 2021-03-24 19:50) [ 1.408230] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8 [ 1.414505] sunxi-mmc 4020000.sdmmc: No vmmc regulator found [ 1.420822] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found [ 1.427313] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found [ 1.433753] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found [ 1.440279] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found [ 1.446819] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found [ 1.453345] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found [ 1.460481] sunxi-mmc 4020000.sdmmc: Got CD GPIO [ 1.466023] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail [ 1.472776] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.484002] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator [ 1.504138] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.528650] sunxi-mmc 4020000.sdmmc: detmode:gpio irq [ 1.534414] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.547204] usbcore: registered new interface driver usbhid [ 1.553459] usbhid: USB HID core driver [ 1.559779] usbcore: registered new interface driver snd-usb-audio [ 1.566792] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.581740] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: id:sunxi,dsp-msgbox new channel: 0x202 -> 0x102! [ 1.593624] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: rpmsg hifi[0] client driver is probed [ 1.605186] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.617781] NET: Registered protocol family 10 [ 1.624382] Segment Routing with IPv6 [ 1.628674] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.636714] NET: Registered protocol family 17 [ 1.641824] can: controller area network core (rev 20170425 abi 9) [ 1.649044] NET: Registered protocol family 29 [ 1.654083] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.665732] can: raw protocol (rev 20170425) [ 1.670522] can: broadcast manager protocol (rev 20170425 t) [ 1.677018] can: netlink gateway (rev 20190810) max_hops=1 [ 1.683707] Bluetooth: RFCOMM TTY layer initialized [ 1.689279] Bluetooth: RFCOMM socket layer initialized [ 1.695185] Bluetooth: RFCOMM ver 1.11 [ 1.700419] Loading compiled-in X.509 certificates [ 1.709168] HDMI 2.0 driver init start! [ 1.713678] boot_hdmi=false [ 1.716928] ERROR: pinctrl_get for HDMI2.0 DDC fail [ 1.724202] HDMI2.0 module init end [ 1.733651] mmc0: host does not support reading read-only switch, assuming write-enable [ 1.744437] sunxi-mmc 4020000.sdmmc: sdc set ios:blk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 1.771909] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 1.788349] get usb_detect_mode is fail, -22 [ 1.793120] get det_vbus is fail, -84 [ 1.797343] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 1.809095] get id is fail, -84 [ 1.812871] mmc0: new high speed SD card at address 2165 [ 1.820149] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 1.830454] mmcblk0: mmc0:2165 APPSD 476 MiB [ 1.841007] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 1.848987] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 1.859026] clk: Not disabling unused clocks [ 1.864138] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 [ 1.869283] ALSA device list: [ 1.872603] No soundcards found. [ 1.876568] cfg80211: failed to load regulatory.db [ 1.885081] alloc_fd: slot 0 not NULL! [ 1.898414] VFS: Mounted root (squashfs filesystem) readonly on device 179:5. [ 1.909898] devtmpfs: mounted [ 1.913451] Freeing unused kernel memory: 192K [ 1.918630] This architecture does not have kernel memory protection. [ 1.925953] Run /sbin/init as init process [ 2.498323] random: fast init done [ 2.601168] init: Console is alive [ 2.605520] init: - watchdog - [ 2.609131] init: - preinit - [ 2.858650] random: procd: uninitialized urandom read (4 bytes read) formating /dev/by-name/UDISK to ext4 /etc/preinit: line 1: mkfs.ext4: not found [ 3.775346] mount_root: mounting /dev/root [ 3.781106] mount_root: loading kmods from internal overlay [ 3.903325] block: attempting to load /etc/config/fstab [ 3.932039] block: extroot: device not present, retrying in 5 seconds [ 5.563577] hdmi_hpd_sys_config_release [ 9.013933] block: extroot: cannot find device UDISK [ 9.033416] procd: - early - [ 9.037897] procd: - watchdog - [ 9.079925] random: procd: uninitialized urandom read (4 bytes read) [ 9.411168] procd: - watchdog - [ 9.424080] procd: - ubus - [ 9.428060] procd (1): /proc/107/oom_adj is deprecated, please use /proc/107/oom_score_adj instead. [ 9.513906] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.723779] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.774928] procd: - init - Please press Enter to activate this console. [ 11.464206] fuse: init (API version 7.31) [ 11.867475] file system registered [ 11.887515] usbcore: registered new interface driver uvcvideo [ 11.915704] USB Video Class driver (1.1.1) [ 12.099732] configfs-gadget 4100000.udc-controller: failed to start g1: -19 [ 12.675667] read descriptors [ 12.678938] read strings [ 16.785377] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 16.894103] ======== XRADIO WIFI OPEN ======== [ 16.902749] [XRADIO] Driver Label:XR_V02.16.84_P2P_HT40_01.31 [ 16.910506] [XRADIO] Allocated hw_priv @ (____ptrval____) [ 16.916864] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 16.927415] Oops [#1] [ 16.929954] Modules linked in: xr829(+) iptable_filter ipt_REJECT uvcvideo videobuf2_vmalloc videobuf2_memops fuse [ 16.941520] CPU: 0 PID: 174 Comm: kmodloader Not tainted 5.4.61 #60 [ 16.948505] sepc: ffffffe0003190ce ra : ffffffe0003191fe sp : ffffffe000a0fa80 [ 16.956556] gp : ffffffe0008ce8f0 tp : ffffffe00301cb40 t0 : ffffffe000a77408 [ 16.964606] t1 : 0000000000000000 t2 : 0000000000000000 s0 : ffffffe000a0fab0 [ 16.972655] s1 : 0000000000000001 a0 : 0000000000000001 a1 : 0000000000000000 [ 16.980705] a2 : 0000000000000001 a3 : ffffffe000a77408 a4 : 0000000000000000 [ 16.988755] a5 : 0000000000000004 a6 : 00000000000100cf a7 : 0000000000000200 [ 16.996805] s2 : ffffffe000882f10 s3 : ffffffe000882f10 s4 : ffffffe000a76668 [ 17.004855] s5 : ffffffdf80a04e08 s6 : 0000000000000003 s7 : 0000000000000001 [ 17.012905] s8 : 0000000000000100 s9 : 0000000000000013 s10: ffffffe000080496 [ 17.020955] s11: ffffffdf80a16590 t3 : ffffffe00002b2b8 t4 : 0000000000000101 [ 17.029003] t5 : 0000000000000100 t6 : 0000000000040000 [ 17.034923] sstatus: 0000000200000120 sbadaddr: 0000000000000000 scause: 000000000000000d [ 17.044962] ---[ end trace a5475755f3688b80 ]--- Trying to connect to SWUpdate... [ 145.986626] random: crng init done [ 145.990431] random: 6 urandom warning(s) missed due to ratelimiting一直卡在这里。
-
回复: F133进不了系统发布在 D1系列-RISC-V
@whycan 大佬，刷了还是进不了。
[288]HELLO! BOOT0 is starting! [290]BOOT0 commit : 27369ab [293]set pll start [295]periph0 has been enabled [298]set pll end [299][pmu]: bus read error [302]board init ok [304]ZQ value = 0x2f*********** [307]get_pmu_exist() = -1 [309]ddr_efuse_type: 0xa [312][AUTO DEBUG] single rank and full DQ! [316]ddr_efuse_type: 0xa [319][AUTO DEBUG] rank 0 row = 13 [322][AUTO DEBUG] rank 0 bank = 4 [325][AUTO DEBUG] rank 0 page size = 2 KB [329]DRAM BOOT DRIVE INFO: V0.24 [332]DRAM CLK = 528 MHz [334]DRAM Type = 2 (2:DDR2,3:DDR3) [338]DRAMC read ODT off. [340]DRAM ODT off. [342]ddr_efuse_type: 0xa [345]DRAM SIZE =64 M [348]DRAM simple test OK. [351]dram size =64 [353]card no is 0 [354]sdcard 0 line count 4 [357][mmc]: mmc driver ver 2021-04-2 16:45 [366][mmc]: Wrong media type 0x0 [369][mmc]: ***Try SD card 0*** [379][mmc]: HSSDR52/SDR25 4 bit [382][mmc]: 50000000 Hz [384][mmc]: 476 MB [386][mmc]: ***SD/MMC 0 init OK!!!*** [440]Loading boot-pkg Succeed(index=0). [444]Entry_name = opensbi [447]Entry_name = u-boot [451]Entry_name = dtb [454]mmc not para [455]Jump to second Boot. OpenSBI v0.6 ____ _____ ____ _____ / __ \ / ____| _ \_ _| | | | |_ __ ___ _ __ | (___ | |_) || | | | | | '_ \ / _ \ '_ \ \___ \| _ < | | | |__| | |_) | __/ | | |____) | |_) || |_ \____/| .__/ \___|_| |_|_____/|____/_____| | | |_| Platform Name : T-HEAD Xuantie Platform Platform HART Features : RV64ACDFIMSUVX Platform Max HARTs : 1 Current Hart : 0 Firmware Base : 0x40000400 Firmware Size : 75 KB Runtime SBI Version : 0.2 MIDELEG : 0x0000000000000222 MEDELEG : 0x000000000000b1ff PMP0 : 0x0000000040000000-0x000000004001ffff (A) PMP1 : 0x0000000040000000-0x000000007fffffff (A,R,W,X) PMP2 : 0x0000000080000000-0x00000000bfffffff (A,R,W,X) PMP3 : 0x0000000000020000-0x0000000000027fff (A, U-Boot 2018.05-g0a88ac9-dirty (Sep 02 2021 - 15:47:05 +0800) Allwinner Technology [00.539]DRAM: 64 MiB [00.541]Relocation Offset is: 01ef0000 [00.545]secure enable bit: 0 [00.548]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz [00.554]flash init start [00.556]workmode = 0,storage type = 1 [00.560][mmc]: mmc driver ver uboot2018:2021-04-16 14:23:00-1 [00.566][mmc]: get sdc_type fail and use default host:tm1. [00.572][mmc]: can't find node "mmc0",will add new node [00.577][mmc]: fdt err returned <no error> [00.580][mmc]: Using default timing para [00.584][mmc]: SUNXI SDMMC Controller Version:0x50310 [00.603][mmc]: card_caps:0x3000000a [00.606][mmc]: host_caps:0x3000003f [00.610]sunxi flash init ok [00.612]line:714 init_clocks __clk_init: clk pll_periph0x2 already initialized register fix_factor clk error [00.622]drv_disp_init request pwm success, pwm2:pwm2:0x2000c00. [00.639]drv_disp_init finish [00.642]boot_gui_init:start [00.645]set disp.dev2_output_type fail. using defval=0 [00.836]boot_gui_init:finish sunxi_partition_get_partno_byname: try part 1, ret = 0 sunxi_partition_get_partno_byname: try part 2, ret = 0 sunxi_partition_get_partno_byname: try part 3, ret = 0 sunxi_partition_get_partno_byname: try part 4, ret = 0 sunxi_partition_get_partno_byname: try part 5, ret = 0 sunxi_partition_get_partno_byname: try part 6, ret = 0 sunxi_partition_get_partno_byname: try part 7, ret = 0 sunxi_partition_get_partno_byname: try part 8, ret = 0 sunxi_partition_get_partno_byname: try part 9, ret = -1 partno erro : can't find partition bootloader sunxi_partition_get_partno_byname: try part 1, ret = 0 54 bytes read in 1 ms (52.7 KiB/s) [01.244]bmp_name=bootlogo.bmp s[01.248]LCD open finish ize 307254 307254 bytes read in 31 ms (9.5 MiB/s) [01.298]Loading Environment from SUNXI_FLASH... OK [01.319]out of usb burn from boot: not need burn key root_partition is rootfs set root to /dev/mmcblk0p5 [01.329]update part info [01.332]update bootcmd [01.336]change working_fdt 0x42aafda8 to 0x42a8fda8 [01.357]update dts Hit any key to stop autoboot: 0 Android's image name: d1-nezha No reserved memory region found in source FDT [01.843] Starting kernel ... [01.846][mmc]: MMC Device 2 not found [01.849][mmc]: mmc 2 not find, so not exit [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000 [ 0.000000] Linux version 5.4.61 (cube@ubuntu) (riscv64-unknown-linux-gnu-gcc (C-SKY RISCV Tools V1.8.4 B20200702) 8.1.0, GNU ld (GNU Binutils) 2.32) #44 PREEMPT Thu Sep 2 09:24:07 UTC 2021 [ 0.000000] cma: Reserved 8 MiB at 0x0000000043800000 [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000040200000-0x0000000043ffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040200000-0x0000000043ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x0000000043ffffff] [ 0.000000] On node 0 totalpages: 15872 [ 0.000000] DMA32 zone: 217 pages used for memmap [ 0.000000] DMA32 zone: 0 pages reserved [ 0.000000] DMA32 zone: 15872 pages, LIFO batch:3 [ 0.000000] elf_hwcap is 0x20112d [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 15655 [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p5 init=/sbin/init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:dsp0@mmcblk0p6:recovery@mmcblk0p7:UDISK@mmcblk0p8 cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun20iw1p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.05-g0a88ac9-dirty(09/02/2021-15:47:05) mbr_off [ 0.000000] Dentry cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.000000] Sorting __ex_table... [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 42216K/63488K available (6067K kernel code, 663K rwdata, 2093K rodata, 192K init, 254K bss, 13080K reserved, 8192K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0 [ 0.000000] plic: mapped 200 interrupts with 1 handlers for 2 contexts. [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [0] [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000007] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000029] riscv_timer_clockevent depends on broadcast, but no broadcast function available [ 0.000373] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.001018] Console: colour dummy device 80x25 [ 0.001063] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.001083] pid_max: default: 32768 minimum: 301 [ 0.001296] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.001317] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.003384] ASID allocator initialised with 65536 entries [ 0.003589] rcu: Hierarchical SRCU implementation. [ 0.004333] devtmpfs: initialized [ 0.022831] random: get_random_u32 called from bucket_table_alloc.isra.31+0x4e/0x15e with crng_init=0 [ 0.023804] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.023840] futex hash table entries: 256 (order: 0, 6144 bytes, linear) [ 0.024412] pinctrl core: initialized pinctrl subsystem [ 0.025952] NET: Registered protocol family 16 [ 0.028014] DMA: preallocated 256 KiB pool for atomic allocations [ 0.028764] cpuidle: using governor menu [ 0.074788] rtc_ccu: sunxi ccu init OK [ 0.082772] clock: sunxi ccu init OK [ 0.083930] clock: sunxi ccu init OK [ 0.125032] iommu: Default domain type: Translated [ 0.125232] sunxi iommu: irq = 4 [ 0.126543] SCSI subsystem initialized [ 0.126944] usbcore: registered new interface driver usbfs [ 0.127036] usbcore: registered new interface driver hub [ 0.127158] usbcore: registered new device driver usb [ 0.127365] mc: Linux media interface: v0.10 [ 0.127470] videodev: Linux video capture interface: v2.00 [ 0.128775] sunxi-msgbox-amp 3003000.msgbox: invalid resource [ 0.129546] Advanced Linux Sound Architecture Driver Initialized. [ 0.130215] Bluetooth: Core ver 2.22 [ 0.130310] NET: Registered protocol family 31 [ 0.130322] Bluetooth: HCI device and connection manager initialized [ 0.130351] Bluetooth: HCI socket layer initialized [ 0.130369] Bluetooth: L2CAP socket layer initialized [ 0.130412] Bluetooth: SCO socket layer initialized [ 0.130878] pwm module init! [ 0.132616] g2d 5410000.g2d: Adding to iommu group 0 [ 0.133206] G2D: rcq version initialized.major:250 [ 0.134002] input: sunxi-keyboard as /devices/virtual/input/input0 [ 0.135569] clocksource: Switched to clocksource riscv_clocksource [ 0.149289] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver [ 0.167871] thermal_sys: Registered thermal governor 'step_wise' [ 0.167878] thermal_sys: Registered thermal governor 'user_space' [ 0.168480] NET: Registered protocol family 2 [ 0.169390] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.169442] TCP established hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.169463] TCP bind hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.169479] TCP: Hash tables configured (established 512 bind 512) [ 0.169669] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.169716] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.169988] NET: Registered protocol family 1 [ 0.172865] Initialise system trusted keyrings [ 0.173178] workingset: timest!mp_bits=62 max_order=14 bucket_order=0 [ 0.181157] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.202013] Key type asymmetric registered [ 0.202032] Asymmetric key parser 'x509' registered [ 0.202060] io scheduler mq-deadline registered [ 0.202070] io scheduler kyber registered [ 0.202093] atomic64_test: passed [ 0.203515] [DISP]disp_module_init [ 0.204167] disp 5000000.disp: Adding to iommu group 0 [ 0.204833] [DISP] disp_init,line:2385: [ 0.204839] smooth display screen:0 type:1 mode:4 [ 0.247153] display_fb_request,fb_id:0 [ 0.262851] disp_al_manager_apply ouput_type:1 [ 0.263034] [DISP] lcd_clk_config,line:731: [ 0.263049] disp 0, clk: pll(816000000),clk(816000000),dclk(34000000) dsi_rate(34000000) [ 0.263049] clk real:pll(816000000),clk(816000000),dclk(204000000) dsi_rate(150000000) [ 0.263466] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator [ 0.264509] [DISP]disp_module_init finish [ 0.265530] sunxi_sid_init()506 - insmod ok [ 0.266304] pwm-regulator: supplied by regulator-dummy [ 0.274632] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator [ 0.275118] uart uart0: get regulator failed [ 0.275150] uart uart0: uart0 supply uart not found, using dummy regulator [ 0.275536] uart0: ttyS0 at MMIO 0x2500000 (irq = 18, base_baud = 1500000) is a SUNXI [ 0.275633] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n [ 1.037271] printk: console [ttyS0] enabled [ 1.042898] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator [ 1.054429] uart uart1: get regulator failed [ 1.059272] uart uart1: uart1 supply uart not found, using dummy regulator [ 1.067348] uart1: ttyS1 at MMIO 0x2500400 (irq = 19, base_baud = 1500000) is a SUNXI [ 1.077386] misc dump reg init [ 1.081727] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9 [ 1.088992] sunxi-rfkill soc@3000000:rfkill@0: devm_pinctrl_get() failed! [ 1.096628] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed [ 1.103920] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed [ 1.111342] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1) [ 1.117883] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power. [ 1.124797] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1) [ 1.132532] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1 [ 1.140414] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1 [ 1.148559] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled [ 1.156252] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power. [ 1.162979] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1) [ 1.170540] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=210 assert=0 [ 1.178953] [ADDR_MGT] addr_mgt_probe: module version: v1.0.9 [ 1.186647] [ADDR_MGT] addr_mgt_probe: success. [ 1.193182] libphy: Fixed MDIO Bus: probed [ 1.197865] CAN device driver interface [ 1.202524] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.209864] sunxi-ehci: EHCI SUNXI driver [ 1.214953] get ehci1-controller wakeup-source is fail. [ 1.221001] sunxi ehci1-controller don't init wakeup source [ 1.227277] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xffffffe0008fbf20, 0x:ffffffd004078000, irq_no:31 [ 1.240823] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply drvvbus not found, using dummy regulator [ 1.253424] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller [ 1.260708] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1 [ 1.270610] sunxi-ehci 4200000.ehci1-controller: irq 49, io mem 0x04200000 [ 1.305613] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00 [ 1.314506] hub 1-0:1.0: USB hub found [ 1.318842] hub 1-0:1.0: 1 port detected [ 1.324172] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.331200] sunxi-ohci: OHCI SUNXI driver [ 1.336349] get ohci1-controller wakeup-source is fail. [ 1.342306] sunxi ohci1-controller don't init wakeup source [ 1.348585] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xffffffe0008fca60 [ 1.359030] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply drvvbus not found, using dummy regulator [ 1.371570] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller [ 1.378846] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2 [ 1.388686] sunxi-ohci 4200400.ohci1-controller: irq 50, io mem 0x04200400 [ 1.470670] hub 2-0:1.0: USB hub found [ 1.474922] hub 2-0:1.0: 1 port detected [ 1.480642] usbcore: registered new interface driver uas [ 1.486849] usbcore: registered new interface driver usb-storage [ 1.493623] usbcore: registered new interface driver ums-alauda [ 1.500428] usbcore: registered new interface driver ums-cypress [ 1.507271] usbcore: registered new interface driver ums-datafab [ 1.514061] usbcore: registered new interface driver ums_eneub6250 [ 1.521091] usbcore: registered new interface driver ums-freecom [ 1.527927] usbcore: registered new interface driver ums-isd200 [ 1.534602] usbcore: registered new interface driver ums-jumpshot [ 1.541531] usbcore: registered new interface driver ums-karma [ 1.548171] usbcore: registered new interface driver ums-onetouch [ 1.555081] usbcore: registered new interface driver ums-realtek [ 1.561914] usbcore: registered new interface driver ums-sddr09 [ 1.568653] usbcore: registered new interface driver ums-sddr55 [ 1.575325] usbcore: registered new interface driver ums-usbat [ 1.583091] sunxi_gpadc_init,1968, success [ 1.588726] sunxi-rtc 7090000.rtc: errata__fix_alarm_day_reg_default_value(): ALARM0_DAY_REG=0, set it to 1 [ 1.601111] sunxi-rtc 7090000.rtc: registered as rtc0 [ 1.606957] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:03 UTC (3) [ 1.615858] sunxi-rtc 7090000.rtc: sunxi rtc probed [ 1.621734] i2c /dev entries driver [ 1.625809] IR NEC protocol handler initialized [ 1.631612] sunxi cedar version 1.1 [ 1.635883] sunxi-cedar 1c0e000.ve: Adding to iommu group 0 [ 1.642132] VE: install start!!! [ 1.642132] [ 1.647724] VE: cedar-ve the get irq is 6 [ 1.647724] [ 1.654120] VE: ve_debug_proc_info:(____ptrval____), data:(____ptrval____), lock:(____ptrval____) [ 1.654120] [ 1.665721] VE: install end!!! [ 1.665721] [ 1.672302] sunxi-wdt 6011000.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 1.681539] Bluetooth: HCI UART driver ver 2.3 [ 1.686547] Bluetooth: HCI UART protocol H4 registered [ 1.692277] Bluetooth: HCI UART protocol BCSP registered [ 1.698229] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10 [ 1.705539] [XR_BT_LPM] bluesleep_probe: bt_wake polarity: 1 [ 1.711989] [XR_BT_LPM] bluesleep_probe: host_wake polarity: 1 [ 1.718576] [XR_BT_LPM] bluesleep_probe: wakeup source is disabled! [ 1.718576] [ 1.727253] [XR_BT_LPM] bluesleep_probe: uart_index(1) [ 1.736326] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.19 2021-03-24 19:50) [ 1.746340] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8 [ 1.752518] sunxi-mmc 4020000.sdmmc: No vmmc regulator found [ 1.758881] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found [ 1.765289] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found [ 1.771726] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found [ 1.778260] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found [ 1.784764] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found [ 1.791294] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found [ 1.798357] sunxi-mmc 4020000.sdmmc: Got CD GPIO [ 1.803839] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail [ 1.810566] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.821723] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator [ 1.841876] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.866331] sunxi-mmc 4020000.sdmmc: detmode:gpio irq [ 1.872009] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.884323] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.19 2021-03-24 19:50) [ 1.894345] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8 [ 1.900694] sunxi-mmc 4021000.sdmmc: No vmmc regulator found [ 1.907081] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found [ 1.913537] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found [ 1.919997] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.931577] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found [ 1.938118] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found [ 1.944622] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found [ 1.951260] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found [ 1.957861] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed [ 1.967339] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.979494] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.990688] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 1.999627] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.011230] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.035546] sunxi-mmc 4021000.sdmmc: detmode:manually by software [ 2.043261] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 2.050703] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator [ 2.061713] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 2.068644] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.080555] sunxi_led_probe()1715 - start [ 2.085296] sunxi_get_str_of_property()1560 - failed to get the string of propname led_regulator! [ 2.095343] sunxi_register_led_classdev()1448 - led_classdev start [ 2.103665] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.115310] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.127948] sunxi_led_probe()1820 - finish [ 2.133278] usbcore: registered new interface driver usbhid [ 2.139721] usbhid: USB HID core driver [ 2.144081] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.156425] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.163986] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.170889] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.182552] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.189745] usbcore: registered new interface driver snd-usb-audio [ 2.196670] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.203476] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 2.217796] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator [ 2.229060] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 2.242199] sunxi-daudio 2034000.daudio: regulator missing or invalid [ 2.250727] [AUDIOCODEC][sunxi_codec_parse_params][2094]:digital_vol:0, lineout_vol:26, mic1gain:19, mic2gain:19 pa_msleep:120, pa_level:1, pa_pwr_level:1 [ 2.250727] [ 2.268009] mmc0: new high speed SD card at address 2165 [ 2.275377] mmcblk0: mmc0:2165 APPSD 476 MiB [ 2.282875] [AUDIOCODEC][sunxi_codec_parse_params][2130]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0 [ 2.295001] [AUDIOCODEC][sunxi_internal_codec_probe][2266]:codec probe finished [ 2.303405] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 [ 2.309735] sid_rd_ver_reg()254 - ver >= 4, soc ver:5 [ 2.315423] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present! [ 2.328418] [SNDCODEC][sunxi_card_init][583]:card init finished [ 2.337850] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok [ 2.349255] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input1 [ 2.361482] [SNDCODEC][sunxi_card_dev_probe][832]:register card finished [ 2.369848] sunxi-rpaf-dsp soc@3000000:rpaf-dsp@203034c: register device finished! [ 2.378386] sunxi-rpaf-dsp soc@3000000:rpaf-dsp@203034c: [rpaf_dsp0] probe finished! [ 2.387498] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: id:sunxi,dsp-msgbox new channel: 0x202 -> 0x102! [ 2.399114] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: rpmsg hifi[0] client driver is probed [ 2.411305] NET: Registered protocol family 10 [ 2.417813] Segment Routing with IPv6 [ 2.422115] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.429727] NET: Registered protocol family 17 [ 2.434765] can: controller area network core (rev 20170425 abi 9) [ 2.441881] NET: Registered protocol family 29 [ 2.446925] can: raw protocol (rev 20170425) [ 2.451690] can: broadcast manager protocol (rev 20170425 t) [ 2.458054] can: netlink gateway (rev 20190810) max_hops=1 [ 2.464550] Bluetooth: RFCOMM TTY layer initialized [ 2.470131] Bluetooth: RFCOMM socket layer initialized [ 2.475932] Bluetooth: RFCOMM ver 1.11 [ 2.481225] Loading compiled-in X.509 certificates [ 2.489404] HDMI 2.0 driver init start! [ 2.493703] boot_hdmi=false [ 2.497008] ERROR: pinctrl_get for HDMI2.0 DDC fail [ 2.504127] HDMI2.0 module init end [ 2.531610] twi twi2: twi2 supply twi not found, using dummy regulator [ 2.574119] twi_stop()478 - [i2c2] STOP can't sendout! [ 2.579856] sunxi_i2c_core_process()1632 - [i2c2] STOP failed! [ 2.586450] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x48, dev addr: 0x38) [ 2.595840] pcf857x: probe of 2-0038 failed with error -70 [ 2.602013] sunxi_i2c_probe()2262 - [i2c2] probe success [ 2.612806] debugfs: Directory '2031000.dmic' with parent 'snddmic' already present! [ 2.623365] sunxi-audio-card 2031060.sounddmic: dmic-hifi <-> 2031000.dmic mapping ok [ 2.633946] debugfs: Directory '2034000.daudio' with parent 'sndhdmi' already present! [ 2.644981] sunxi-audio-card 20340a0.sounddaudio2: 20340a4.hdmiaudio <-> 2034000.daudio mapping ok [ 2.656626] get ehci0-controller wakeup-source is fail. [ 2.662580] sunxi ehci0-controller don't init wakeup source [ 2.668888] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe0008fbb60, 0x:ffffffd0040fc000, irq_no:2e [ 2.682428] [sunxi-ehci0]: Not init ehci0 [ 2.687487] get ohci0-controller wakeup-source is fail. [ 2.693453] sunxi ohci0-controller don't init wakeup source [ 2.699732] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe0008fc6a0 [ 2.710166] [sunxi-ohci0]: Not init ohci0 [ 2.717262] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 2.728454] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 2.736123] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 2.745835] clk: Not disabling unused clocks [ 2.750609] ALSA device list: [ 2.753915] #0: audiocodec [ 2.757278] cfg80211: failed to load regulatory.db [ 2.762719] #1: snddmic [ 2.765754] #2: sndhdmi [ 2.768688] alloc_fd: slot 0 not NULL! [ 2.781290] VFS: Mounted root (squashfs filesystem) readonly on device 179:5. [ 2.792319] devtmpfs: mounted [ 2.795975] Freeing unused kernel memory: 192K [ 2.800954] This architecture does not have kernel memory protection. [ 2.808271] Run /sbin/init as init process [ 3.073979] [SNDCODEC][sunxi_check_hs_detect_status][191]:plugin --> switch:1 [ 3.482284] init: Console is alive [ 3.486573] init: - watchdog - [ 3.490162] init: - preinit - [ 3.783009] random: procd: uninitialized urandom read (4 bytes read) formating /dev/by-name/UDISK to ext4 /etc/preinit: line 1: mkfs.ext4: not found [ 4.637337] mount_root: mounting /dev/root [ 4.643026] mount_root: loading kmods from internal overlay [ 4.763561] block: attempting to load /etc/config/fstab [ 4.791862] block: extroot: device not present, retrying in 5 seconds [ 4.805643] [ 4.805643] insmod_host_driver [ 4.805643] [ 4.812350] [ehci0-controller]: sunxi_usb_enable_ehci [ 4.818082] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe0008fbb60, 0x:ffffffd0040fc000, irq_no:2e [ 4.833297] sunxi-ehci 4101000.ehci0-controller: EHCI Host Controller [ 4.840628] sunxi-ehci 4101000.ehci0-controller: new USB bus registered, assigned bus number 3 [ 4.850570] sunxi-ehci 4101000.ehci0-controller: irq 46, io mem 0x04101000 [ 4.885603] sunxi-ehci 4101000.ehci0-controller: USB 2.0 started, EHCI 1.00 [ 4.894915] hub 3-0:1.0: USB hub found [ 4.899270] hub 3-0:1.0: 1 port detected [ 4.904743] [ohci0-controller]: sunxi_usb_enable_ohci [ 4.910501] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe0008fc6a0 [ 4.921524] sunxi-ohci 4101400.ohci0-controller: OHCI Host Controller [ 4.928812] sunxi-ohci 4101400.ohci0-controller: new USB bus registered, assigned bus number 4 [ 4.938571] debugfs: Directory 'sunxi-ohci' with parent 'ohci' already present! [ 4.946823] sunxi-ohci 4101400.ohci0-controller: irq 47, io mem 0x04101400 [ 5.021066] hub 4-0:1.0: USB hub found [ 5.025319] hub 4-0:1.0: 1 port detected [ 6.345599] hdmi_hpd_sys_config_release [ 9.872367] block: extroot: cannot find device UDISK [ 9.892596] procd: - early - [ 9.896206] procd: - watchdog - [ 9.985054] random: procd: uninitialized urandom read (4 bytes read) [ 10.359269] procd: - watchdog - [ 10.363136] procd: - ubus - [ 10.368651] procd (1): /proc/112/oom_adj is deprecated, please use /proc/112/oom_score_adj instead. [ 10.454188] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.685775] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.733129] procd: - init - Please press Enter to activate this console. [ 12.236083] fuse: init (API version 7.31) [ 12.606077] file system registered [ 12.736115] usbcore: registered new interface driver uvcvideo [ 12.742531] USB Video Class driver (1.1.1) [ 12.748442] configfs-gadget 4100000.udc-controller: failed to start g1: -19 [ 13.345775] read descriptors [ 13.364445] read strings [ 17.610659] ======== XRADIO WIFI OPEN ======== [ 17.622976] [XRADIO] Driver Label:XR_V02.16.84_P2P_HT40_01.31 [ 17.636683] [XRADIO] Allocated hw_priv @ (____ptrval____) [ 17.660805] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 [ 17.696799] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success [ 17.894708] random: fast init done [ 18.227612] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 18.238857] [XRADIO] Detect SDIO card 1 [ 18.265805] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 18.305682] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 18.349139] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 18.356891] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 18.363754] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 18.392392] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 18.422021] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 18.429669] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 18.437341] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 18.444960] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 18.451826] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 20.325752] sunxi-rfkill soc@3000000:rfkill@0: wlan power off success [ 20.433354] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 20.444534] [XRADIO] Remove SDIO card 1 [ 20.454807] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 20.466686] [SBUS_ERR] sdio probe timeout! [ 20.471362] [XRADIO_ERR] sbus_sdio_init failed [ 20.477947] xradio_core_init failed (-110)! [ 20.482721] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 20.516464] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 20.524134] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 20.531169] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 20.546626] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 20.564859] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 20.572493] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 20.580124] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 20.587596] xt_time: kernel timezone is -0000 [ 20.592486] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 20.599323] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 20.624500] Error: Driver 'gt9xxnew_ts' is already registered, aborting... [ 22.094619] ======== XRADIO WIFI OPEN ======== [ 22.100334] [XRADIO] Driver Label:XR_V02.16.84_P2P_HT40_01.31 [ 22.107276] [XRADIO] Allocated hw_priv @ (____ptrval____) [ 22.118559] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 [ 22.140276] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success [ 22.354501] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 22.365754] [XRADIO] Detect SDIO card 1 [ 22.375727] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 22.398878] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 22.421697] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 22.429446] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 22.436347] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 22.451215] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 22.465062] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 22.472768] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 22.480576] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 22.488579] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 22.495373] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 24.405750] sunxi-rfkill soc@3000000:rfkill@0: wlan power off success [ 24.513265] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 24.524490] [XRADIO] Remove SDIO card 1 [ 24.534779] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 24.546631] [SBUS_ERR] sdio probe timeout! [ 24.551282] [XRADIO_ERR] sbus_sdio_init failed [ 24.557841] xradio_core_init failed (-110)! [ 24.562616] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 24.596461] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 24.604133] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 24.611210] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 24.626610] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 24.643801] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 24.651437] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 24.659071] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 24.666752] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 24.673534] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B Trying to connect to SWUpdate... [ 27.677614] [SNDCODEC][sunxi_card_hw_params][620]:stream_flag: 0 -
F133进不了系统发布在 D1系列-RISC-V
求大神们帮忙分析一下，进不了系统。
[74]HELLO! BOOT0 is starting! [77]BOOT0 commit : 27369ab [79]set pll start [81]periph0 has been enabled [84]set pll end [86][pmu]: bus read error [88]board init ok [90]ZQ value = 0x2f*********** [93]get_pmu_exist() = -1 [95]ddr_efuse_type: 0xa [98][AUTO DEBUG] single rank and full DQ! [102]ddr_efuse_type: 0xa [105][AUTO DEBUG] rank 0 row = 13 [108][AUTO DEBUG] rank 0 bank = 4 [111][AUTO DEBUG] rank 0 page size = 2 KB [115]DRAM BOOT DRIVE INFO: V0.24 [118]DRAM CLK = 528 MHz [120]DRAM Type = 2 (2:DDR2,3:DDR3) [123]DRAMC read ODT off. [126]DRAM ODT off. [128]ddr_efuse_type: 0xa [130]DRAM SIZE =64 M [134]DRAM simple test OK. [136]dram size =64 [138]card no is 0 [140]sdcard 0 line count 4 [142][mmc]: mmc driver ver 2021-04-2 16:45 [152][mmc]: Wrong media type 0x0 [155][mmc]: ***Try SD card 0*** [163][mmc]: HSSDR52/SDR25 4 bit [166][mmc]: 50000000 Hz [168][mmc]: 14760 MB [170][mmc]: ***SD/MMC 0 init OK!!!*** [218]Loading boot-pkg Succeed(index=0). [222]Entry_name = opensbi [225]Entry_name = u-boot [229]Entry_name = dtb [232]mmc not para [233]Jump to second Boot. OpenSBI v0.6 ____ _____ ____ _____ / __ \ / ____| _ \_ _| | | | |_ __ ___ _ __ | (___ | |_) || | | | | | '_ \ / _ \ '_ \ \___ \| _ < | | | |__| | |_) | __/ | | |____) | |_) || |_ \____/| .__/ \___|_| |_|_____/|____/_____| | | |_| Platform Name : T-HEAD Xuantie Platform Platform HART Features : RV64ACDFIMSUVX Platform Max HARTs : 1 Current Hart : 0 Firmware Base : 0x40000400 Firmware Size : 75 KB Runtime SBI Version : 0.2 MIDELEG : 0x0000000000000222 MEDELEG : 0x000000000000b1ff PMP0 : 0x0000000040000000-0x000000004001ffff (A) PMP1 : 0x0000000040000000-0x000000007fffffff (A,R,W,X) PMP2 : 0x0000000080000000-0x00000000bfffffff (A,R,W,X) PMP3 : 0x0000000000020000-0x0000000000027fff (A, U-Boot 2018.05-g0a88ac9 (Apr 30 2021 - 11:23:28 +0000) Allwinner Technology [00.316]DRAM: 64 MiB [00.318]Relocation Offset is: 01ef0000 [00.323]secure enable bit: 0 [00.325]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz [00.331]flash init start [00.334]workmode = 0,storage type = 1 [00.337][mmc]: mmc driver ver uboot2018:2021-04-16 14:23:00-1 [00.343][mmc]: get sdc_type fail and use default host:tm1. [00.349][mmc]: can't find node "mmc0",will add new node [00.354][mmc]: fdt err returned <no error> [00.358][mmc]: Using default timing para [00.361][mmc]: SUNXI SDMMC Controller Version:0x50310 [00.379][mmc]: card_caps:0x3000000a [00.382][mmc]: host_caps:0x3000003f [00.385]sunxi flash init ok [00.388]line:714 init_clocks __clk_init: clk pll_periph0x2 already initialized register fix_factor clk error [00.398]drv_disp_init fdt_getprop_u32 s_pwm.pwm-base fail [00.414]drv_disp_init finish [00.416]boot_gui_init:start [00.419]set disp.dev2_output_type fail. using defval=0 [00.425]boot_gui_init:finish partno erro : can't find partition bootloader 54 bytes read in 2 ms (26.4 KiB/s) [00.454]bmp_name=bootlogo.bmp size 307254 307254 bytes read in 15 ms (19.5 MiB/s) no support big size bmp[240x320] on fb[480x272] [00.483]show bmp on fb failed !-1 [00.500]Loading Environment from SUNXI_FLASH... OK [00.519]out of usb burn from boot: not need burn key root_partition is rootfs set root to /dev/mmcblk0p5 [00.530]update part info [00.534]update bootcmd [00.538]change working_fdt 0x42aafda8 to 0x42a8fda8 [00.558]update dts Hit any key to stop autoboot: 0 [00.605]LCD open finish Android's image name: d1-f133evb1_rgb8 No reserved memory region found in source FDT [00.981] Starting kernel ... [00.983][mmc]: MMC Device 2 not found [00.987][mmc]: mmc 2 not find, so not exit [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000 [ 0.000000] Linux version 5.4.61 (allwinner@allwinner-VirtualBox) (riscv64-unknown-linux-gnu-gcc (C-SKY RISCV Tools V1.8.4 B20200702) 8.1.0, GNU ld (GNU Binutils) 2.32) #6 PREEMPT Tue Nov 23 13:19:29 UTC 2021 [ 0.000000] cma: Reserved 8 MiB at 0x0000000043800000 [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000040200000-0x0000000043ffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040200000-0x0000000043ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x0000000043ffffff] [ 0.000000] On node 0 totalpages: 15872 [ 0.000000] DMA32 zone: 217 pages used for memmap [ 0.000000] DMA32 zone: 0 pages reserved [ 0.000000] DMA32 zone: 15872 pages, LIFO batch:3 [ 0.000000] elf_hwcap is 0x20112d [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 15655 [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p5 init=/sbin/init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:dsp0@mmcblk0p6:recovery@mmcblk0p7:UDISK@mmcblk0p8 cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun20iw1p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.05-g0a88ac9(04/30/2021-11:23:28) mbr_offset=15 [ 0.000000] Dentry cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.000000] Sorting __ex_table... [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 43212K/63488K available (6068K kernel code, 663K rwdata, 2093K rodata, 192K init, 254K bss, 12084K reserved, 8192K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0 [ 0.000000] plic: mapped 200 interrupts with 1 handlers for 2 contexts. [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [0] [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000007] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000029] riscv_timer_clockevent depends on broadcast, but no broadcast function available [ 0.000367] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.001006] Console: colour dummy device 80x25 [ 0.001052] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.001070] pid_max: default: 32768 minimum: 301 [ 0.001283] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.001302] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.003312] ASID allocator initialised with 65536 entries [ 0.003514] rcu: Hierarchical SRCU implementation. [ 0.004241] devtmpfs: initialized [ 0.022451] random: get_random_u32 called from bucket_table_alloc.isra.31+0x4e/0x15e with crng_init=0 [ 0.023426] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.023460] futex hash table entries: 256 (order: 0, 6144 bytes, linear) [ 0.024001] pinctrl core: initialized pinctrl subsystem [ 0.025513] NET: Registered protocol family 16 [ 0.027514] DMA: preallocated 256 KiB pool for atomic allocations [ 0.028240] cpuidle: using governor menu [ 0.070741] rtc_ccu: sunxi ccu init OK [ 0.078973] clock: sunxi ccu init OK [ 0.080000] clock: sunxi ccu init OK [ 0.115475] iommu: Default domain type: Translated [ 0.115672] sunxi iommu: irq = 4 [ 0.116919] SCSI subsystem initialized [ 0.117300] usbcore: registered new interface driver usbfs [ 0.117395] usbcore: registered new interface driver hub [ 0.117512] usbcore: registered new device driver usb [ 0.117734] mc: Linux media interface: v0.10 [ 0.117803] videodev: Linux video capture interface: v2.00 [ 0.119053] sunxi-msgbox-amp 3003000.msgbox: invalid resource [ 0.119833] Advanced Linux Sound Architecture Driver Initialized. [ 0.120607] Bluetooth: Core ver 2.22 [ 0.120704] NET: Registered protocol family 31 [ 0.120716] Bluetooth: HCI device and connection manager initialized [ 0.120744] Bluetooth: HCI socket layer initialized [ 0.120760] Bluetooth: L2CAP socket layer initialized [ 0.120803] Bluetooth: SCO socket layer initialized [ 0.121122] pwm module init! [ 0.122759] g2d 5410000.g2d: Adding to iommu group 0 [ 0.123312] G2D: rcq version initialized.major:250 [ 0.124776] clocksource: Switched to clocksource riscv_clocksource [ 0.137932] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver [ 0.156603] thermal_sys: Registered thermal governor 'step_wise' [ 0.156609] thermal_sys: Registered thermal governor 'user_space' [ 0.157200] NET: Registered protocol family 2 [ 0.158093] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.158147] TCP established hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.158168] TCP bind hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.158183] TCP: Hash tables configured (established 512 bind 512) [ 0.158356] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.158404] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.158687] NET: Registered protocol family 1 [ 0.161422] Initialise system trusted keyrings [ 0.161738] workingset: timestamp_bits=62 max_order=14 bucket_order=0 [ 0.169549] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.190004] Key type asymmetric registered [ 0.190023] Asymmetric key parser 'x509' registered [ 0.190050] io scheduler mq-deadline registered [ 0.190060] io scheduler kyber registered [ 0.190082] atomic64_test: passed [ 0.191415] [DISP]disp_module_init [ 0.192093] disp 5000000.disp: Adding to iommu group 0 [ 0.192743] [DISP] disp_init,line:2385: [ 0.192750] smooth display screen:0 type:1 mode:4 [ 0.220917] disp 5000000.disp: 5000000.disp supply vcc-lcd not found, using dummy regulator [ 0.221186] disp 5000000.disp: 5000000.disp supply vcc-pd not found, using dummy regulator [ 0.233514] [DISP] disp_sys_pwm_request,line:442: [ 0.233521] disp_sys_pwm_request pwm 8 fail! -517 [ 0.233538] [DISP] disp_sys_pwm_config,line:509: [ 0.233541] disp_sys_pwm_Config, handle is NULL! [ 0.234200] display_fb_request,fb_id:0 [ 0.250393] disp_al_manager_apply ouput_type:1 [ 0.250539] [DISP] lcd_clk_config,line:731: [ 0.250553] disp 0, clk: pll(198000000),clk(198000000),dclk(33000000) dsi_rate(198000000) [ 0.250553] clk real:pll(288000000),clk(288000000),dclk(48000000) dsi_rate(0) [ 0.250611] [DISP] disp_sys_gpio_request,line:276: [ 0.250618] disp_sys_gpio_request failed, gpio_name=lcd_bl_en, gpio=123, value=0, ret=-517 [ 0.250633] [DISP] disp_sys_pwm_request,line:442: [ 0.250637] disp_sys_pwm_request pwm 8 fail! -517 [ 0.251244] [DISP]disp_module_init finish [ 0.252145] sunxi_sid_init()506 - insmod ok [ 0.260583] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator [ 0.261311] uart uart0: get regulator failed [ 0.261345] uart uart0: uart0 supply uart not found, using dummy regulator [ 0.261737] uart0: ttyS0 at MMIO 0x2500000 (irq = 18, base_baud = 1500000) is a SUNXI [ 0.261770] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n [ 1.067736] printk: console [ttyS0] enabled [ 1.073671] misc dump reg init [ 1.079686] libphy: Fixed MDIO Bus: probed [ 1.084301] CAN device driver interface [ 1.089001] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.096392] sunxi-ehci: EHCI SUNXI driver [ 1.101342] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.108374] sunxi-ohci: OHCI SUNXI driver [ 1.113626] usbcore: registered new interface driver uas [ 1.119799] usbcore: registered new interface driver usb-storage [ 1.126722] usbcore: registered new interface driver ums-alauda [ 1.133414] usbcore: registered new interface driver ums-cypress [ 1.140305] usbcore: registered new interface driver ums-datafab [ 1.147140] usbcore: registered new interface driver ums_eneub6250 [ 1.154140] usbcore: registered new interface driver ums-freecom [ 1.161052] usbcore: registered new interface driver ums-isd200 [ 1.167787] usbcore: registered new interface driver ums-jumpshot [ 1.174688] usbcore: registered new interface driver ums-karma [ 1.181346] usbcore: registered new interface driver ums-onetouch [ 1.188349] usbcore: registered new interface driver ums-realtek [ 1.195184] usbcore: registered new interface driver ums-sddr09 [ 1.201896] usbcore: registered new interface driver ums-sddr55 [ 1.208683] usbcore: registered new interface driver ums-usbat [ 1.216090] sunxi_gpadc_init,1968, success [ 1.221469] sunxi-rtc 7090000.rtc: errata__fix_alarm_day_reg_default_value(): ALARM0_DAY_REG=0, set it to 1 [ 1.233887] sunxi-rtc 7090000.rtc: registered as rtc0 [ 1.239691] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:02 UTC (2) [ 1.248651] sunxi-rtc 7090000.rtc: sunxi rtc probed [ 1.254524] i2c /dev entries driver [ 1.258589] IR NEC protocol handler initialized [ 1.264336] sunxi cedar version 1.1 [ 1.268633] sunxi-cedar 1c0e000.ve: Adding to iommu group 0 [ 1.274944] VE: install start!!! [ 1.274944] [ 1.280537] VE: cedar-ve the get irq is 6 [ 1.280537] [ 1.286961] VE: ve_debug_proc_info:(____ptrval____), data:(____ptrval____), lock:(____ptrval____) [ 1.286961] [ 1.298615] VE: install end!!! [ 1.298615] [ 1.305203] sunxi-wdt 6011000.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 1.314367] Bluetooth: HCI UART driver ver 2.3 [ 1.319385] Bluetooth: HCI UART protocol H4 registered [ 1.325202] Bluetooth: HCI UART protocol BCSP registered [ 1.331132] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10 [ 1.341250] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.19 2021-03-24 19:50) [ 1.351331] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8 [ 1.357613] sunxi-mmc 4020000.sdmmc: No vmmc regulator found [ 1.363929] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found [ 1.370412] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found [ 1.376855] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found [ 1.383380] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found [ 1.389920] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found [ 1.396483] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found [ 1.403542] sunxi-mmc 4020000.sdmmc: Got CD GPIO [ 1.409089] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail [ 1.415907] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.427121] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator [ 1.447254] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.471758] sunxi-mmc 4020000.sdmmc: detmode:gpio irq [ 1.477519] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.490412] usbcore: registered new interface driver usbhid [ 1.496858] usbhid: USB HID core driver [ 1.502900] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.514886] usbcore: registered new interface driver snd-usb-audio [ 1.525123] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator [ 1.536667] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator [ 1.548124] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.560966] sun8iw20-pinctrl 2000000.pinctrl: pin PE17 already requested by 2031000.dmic; cannot claim for 2032000.daudio [ 1.573437] sun8iw20-pinctrl 2000000.pinctrl: pin-145 (2032000.daudio) status -22 [ 1.581912] sun8iw20-pinctrl 2000000.pinctrl: could not request pin 145 (PE17) from group PE17 on device 2000000.pinctrl [ 1.594243] sunxi-daudio 2032000.daudio: Error applying setting, reverse things back [ 1.602966] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.614633] sunxi-daudio: probe of 2032000.daudio failed with error -22 [ 1.622830] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator [ 1.634541] sunxi-daudio 2033000.daudio: regulator missing or invalid [ 1.642543] sunxi-daudio 2034000.daudio: regulator missing or invalid [ 1.650790] [AUDIOCODEC][sunxi_codec_parse_params][2094]:digital_vol:0, lineout_vol:26, mic1gain:19, mic2gain:19 pa_msleep:120, pa_level:1, pa_pwr_level:1 [ 1.650790] [ 1.668015] [AUDIOCODEC][sunxi_codec_parse_params][2130]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0 [ 1.679635] [AUDIOCODEC][sunxi_internal_codec_probe][2266]:codec probe finished [ 1.689551] sid_rd_ver_reg()254 - ver >= 4, soc ver:5 [ 1.695450] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present! [ 1.705355] [SNDCODEC][sunxi_card_init][583]:card init finished [ 1.713776] mmc0: host does not support reading read-only switch, assuming write-enable [ 1.724068] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok [ 1.735655] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input0 [ 1.747165] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 1.759554] [SNDCODEC][sunxi_card_dev_probe][832]:register card finished [ 1.767985] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: id:sunxi,dsp-msgbox new channel: 0x202 -> 0x102! [ 1.779604] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 1.791639] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 1.803538] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: rpmsg hifi[0] client driver is probed [ 1.815860] NET: Registered protocol family 10 [ 1.821729] mmc0: new high speed SDHC card at address 1234 [ 1.829169] Segment Routing with IPv6 [ 1.833522] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.841307] mmcblk0: mmc0:1234 SA16G 14.4 GiB [ 1.850304] NET: Registered protocol family 17 [ 1.855786] can: controller area network core (rev 20170425 abi 9) [ 1.862894] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 [ 1.868003] NET: Registered protocol family 29 [ 1.872974] can: raw protocol (rev 20170425) [ 1.880932] can: broadcast manager protocol (rev 20170425 t) [ 1.887365] can: netlink gateway (rev 20190810) max_hops=1 [ 1.893898] Bluetooth: RFCOMM TTY layer initialized [ 1.899589] Bluetooth: RFCOMM socket layer initialized [ 1.905475] Bluetooth: RFCOMM ver 1.11 [ 1.910864] Loading compiled-in X.509 certificates [ 1.919108] HDMI 2.0 driver init start! [ 1.923438] boot_hdmi=false [ 1.926709] ERROR: pinctrl_get for HDMI2.0 DDC fail [ 1.933855] HDMI2.0 module init end [ 1.962796] sun8iw20-pinctrl 2000000.pinctrl: pin PE17 already requested by 2031000.dmic; cannot claim for 2032000.daudio [ 1.975171] sun8iw20-pinctrl 2000000.pinctrl: pin-145 (2032000.daudio) status -22 [ 1.983553] sun8iw20-pinctrl 2000000.pinctrl: could not request pin 145 (PE17) from group PE17 on device 2000000.pinctrl [ 1.995854] sunxi-daudio 2032000.daudio: Error applying setting, reverse things back [ 2.004563] sunxi-daudio: probe of 2032000.daudio failed with error -22 [ 2.015870] debugfs: Directory '2031000.dmic' with parent 'snddmic' already present! [ 2.026489] sunxi-audio-card 2031060.sounddmic: dmic-hifi <-> 2031000.dmic mapping ok [ 2.037230] sunxi-audio-card 20330a0.sounddaudio1: use dummy codec for simple card. [ 2.046148] debugfs: Directory '2033000.daudio' with parent 'snddaudio1' already present! [ 2.057588] sunxi-audio-card 20330a0.sounddaudio1: snd-soc-dummy-dai <-> 2033000.daudio mapping ok [ 2.069277] get ehci0-controller wakeup-source is fail. [ 2.075347] sunxi ehci0-controller don't init wakeup source [ 2.081575] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe0008fbb58, 0x:ffffffd0040f9000, irq_no:2e [ 2.095157] [sunxi-ehci0]: Not init ehci0 [ 2.100205] get ohci0-controller wakeup-source is fail. [ 2.106272] sunxi ohci0-controller don't init wakeup source [ 2.112533] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe0008fc698 [ 2.123013] [sunxi-ohci0]: Not init ohci0 [ 2.128093] get ehci1-controller wakeup-source is fail. [ 2.134074] sunxi ehci1-controller don't init wakeup source [ 2.140383] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xffffffe0008fbf18, 0x:ffffffd004a69000, irq_no:31 [ 2.155474] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller [ 2.162710] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1 [ 2.172663] sunxi-ehci 4200000.ehci1-controller: irq 49, io mem 0x04200000 [ 2.204829] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00 [ 2.213787] hub 1-0:1.0: USB hub found [ 2.218141] hub 1-0:1.0: 1 port detected [ 2.223738] get ohci1-controller wakeup-source is fail. [ 2.229797] sunxi ohci1-controller don't init wakeup source [ 2.236163] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xffffffe0008fca58 [ 2.246974] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller [ 2.254199] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2 [ 2.264124] sunxi-ohci 4200400.ohci1-controller: irq 50, io mem 0x04200400 [ 2.339946] hub 2-0:1.0: USB hub found [ 2.344209] hub 2-0:1.0: 1 port detected [ 2.352722] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 2.364422] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 2.372116] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 2.381896] clk: Not disabling unused clocks [ 2.386809] ALSA device list: [ 2.390125] #0: audiocodec [ 2.393332] #1: snddmic [ 2.396402] cfg80211: failed to load regulatory.db [ 2.401850] #2: snddaudio1 [ 2.405168] alloc_fd: slot 0 not NULL! [ 2.416601] VFS: Mounted root (squashfs filesystem) readonly on device 179:5. [ 2.428676] devtmpfs: mounted [ 2.432269] Freeing unused kernel memory: 192K [ 2.437391] [SNDCODEC][sunxi_check_hs_detect_status][191]:plugin --> switch:1 [ 2.445475] This architecture does not have kernel memory protection. [ 2.452663] Run /sbin/init as init process [ 2.628427] random: fast init done [ 3.127749] init: Console is alive [ 3.131901] init: - watchdog - [ 3.135667] init: - preinit - [ 4.007201] random: procd: uninitialized urandom read (4 bytes read) formating /dev/by-name/UDISK to ext4 /etc/preinit: line 1: mkfs.ext4: not found [ 4.279987] mount_root: mounting /dev/root [ 4.287901] mount_root: loading kmods from internal overlay [ 4.404185] block: attempting to load /etc/config/fstab [ 4.432745] block: extroot: device not present, retrying in 5 seconds [ 5.704817] hdmi_hpd_sys_config_release [ 6.044811] [ 6.044811] insmod_device_driver [ 6.044811] [ 9.511766] block: extroot: cannot find device UDISK [ 9.532415] procd: - early - [ 9.535953] procd: - watchdog - [ 9.665708] random: procd: uninitialized urandom read (4 bytes read) [ 9.936050] procd: - watchdog - [ 9.939931] procd: - ubus - [ 9.943961] procd (1): /proc/109/oom_adj is deprecated, please use /proc/109/oom_score_adj instead. [ 10.035262] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.245421] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.296144] procd: - init - Please press Enter to activate this console. [ 11.872754] fuse: init (API version 7.31) [ 12.151895] file system registered [ 12.331900] configfs-gadget 4100000.udc-controller: failed to start g1: -19 [ 12.425344] usbcore: registered new interface driver uvcvideo [ 12.474886] USB Video Class driver (1.1.1) [ 13.004424] read descriptors [ 13.039562] read strings [ 17.635835] ======== XRADIO WIFI OPEN ======== [ 17.650781] [XRADIO] Driver Label:XR_V02.16.84_P2P_HT40_01.31 [ 17.667359] [XRADIO] Allocated hw_priv @ (____ptrval____) [ 17.689507] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 17.709994] Oops [#1] [ 17.712532] Modules linked in: xr829(+) iptable_filter ipt_REJECT uvcvideo videobuf2_vmalloc videobuf2_memops fuse [ 17.724095] CPU: 0 PID: 172 Comm: kmodloader Not tainted 5.4.61 #6 [ 17.730986] sepc: ffffffe000319158 ra : ffffffe000319288 sp : ffffffe00123ba80 [ 17.739036] gp : ffffffe0008ce8f0 tp : ffffffe00303d600 t0 : ffffffe00127b408 [ 17.747086] t1 : 0000000000000000 t2 : 0000000000000000 s0 : ffffffe00123bab0 [ 17.755135] s1 : 0000000000000001 a0 : 0000000000000001 a1 : 0000000000000000 [ 17.763185] a2 : 0000000000000001 a3 : ffffffe00127b408 a4 : 0000000000000000 [ 17.771235] a5 : 0000000000000004 a6 : 00000000000101f1 a7 : ffffffe0031df000 [ 17.779285] s2 : ffffffe000882f10 s3 : ffffffe000882f10 s4 : ffffffe00127a668 [ 17.787334] s5 : ffffffdf80a04e08 s6 : 0000000000000003 s7 : 0000000000000001 [ 17.795384] s8 : 0000000000000100 s9 : 0000000000000013 s10: ffffffe000080496 [ 17.803433] s11: ffffffdf80a16590 t3 : 0000000000000000 t4 : 0000000043840000 [ 17.811482] t5 : 0000000043840010 t6 : 0000000000000000 [ 17.817401] sstatus: 0000000200000120 sbadaddr: 0000000000000000 scause: 000000000000000d [ 17.830241] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 18.044900] ---[ end trace 1a4935efe55ef2ac ]--- Trying to connect to SWUpdate... [ 22.905536] [SNDCODEC][sunxi_card_hw_params][620]:stream_flag: 0
图片地址)