[Rx][14:59:26.813] [159]HELLO! BOOT0 is starting!
[162]BOOT0 commit : 4b419f21ba
[Rx][14:59:26.955] [250][pmu]: bus read error
[252]set pll start
[254]periph0 has been enabled
[257]set pll end
[259]board init ok
[261]DRAM use internal ZQ!!
[263]ZQ value = 0x2f
[266]chip id check OK
[268]POWER SETTING ERROR!
[270]DRAM BOOT DRIVE INFO: V0.16
[273]DRAM CLK = 528 MHz
[275]DRAM Type = 2 (2:DDR2,3:DDR3)
[279]DRAMC read ODT  off.
[281]DRAM ODT off.
[284]DRAM SIZE =64 M
[286]dram_tpr4:0x0
[293]DRAM simple test OK.
[296]rtc standby flag is 0x0, super standby flag is 0x0
[301]dram size =64
[304]audio:avcc calibration
[306]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32
[312]block from 8 to 32
[Rx][14:59:27.346] [682]Check is correct.
[684]Entry_name        = optee
[687]Entry_name        = u-boot
[696]Entry_name        = dtb
[699]Jump to second Boot.
[Rx][14:59:27.367] M/TC: OP-TEE version: 15ee1539b (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Tue Mar 29 06:48:41 UTC 2022 arm
[Rx][14:59:27.390] E/TC:0 0 platform_standby_fdt_parse:133 no pmu node
[Rx][14:59:27.399] E/TC:0 0 sunxi_twi_parse_from_dt:121 no pmu node
[Rx][14:59:27.427] 

U-Boot 2018.05-ga697d75 (Jul 28 2022 - 05:29:47 +0000) Allwinner Technology

[00.776]CPU:   Allwinner Family
[00.779]Model: sun8iw21
I2C:   
[I2C-ERROR]:twi_send_clk_9pulse() 147 SDA is still Stuck Low, failed. 
ready
[00.839]DRAM:  64 MiB
[00.843]Relocation Offset is: 00ed0000
[Rx][14:59:27.507] [00.87
6]secure enable bit: 0
E/TC:0   tee_read_fdt:433 fine node /firmware/optee failed with FDT_ERR_NOTFOUND
[00.890]smc_tee_inform_fdt failed with: ffff0000
[I2C-ERROR]:twi_stop() 339 STOP can't sendout!
[00.900]pmu_axp2101_probe pmic_bus_read fail
[I2C-ERROR]:twi_stop() 339 STOP can't sendout!
[00.908]bmu_axp2101_probe pmic_bus_read fail
[00.912]CPU=900 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=24Mhz  MBus=300Mhz
[00.918]gic: sec monitor mode
sunxi flash map init
[00.923]flash init start
[00.925]workmode = 0,storage type = 0
[00.933]sunxi-spinand-phy: spinand sample_mode:1 sample_delay:1b

device nand0 , # parts = 4
 #: name		size		offset		mask_flags
 0: boot0               0x00100000	0x00000000	1
 1: uboot               0x00300000	0x00100000	1
 2: secure_storage      0x00100000	0x00400000	1
 3: sys                 0x07b00000	0x00500000	0

active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000

defaults:
mtdids  : nand0=nand
mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
[Rx][14:59:27.722] [01.090]ubi0: attaching mtd4
[Rx][14:59:27.953] [01.304]ubi0: scanning is finished
[01.313]ubi0
: attached mtd4 (name "sys", size 123 MiB)
[01.318]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[01.324]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[01.330]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[01.337]ubi0: good PEBs: 492, bad PEBs: 0, corrupted PEBs: 0
[01.342]ubi0: user volume: 7, internal volumes: 1, max. volumes count: 128
[01.349]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
[01.356]ubi0: available PEBs: 0, total reserved PEBs: 492, PEBs reserved for bad PEB handling: 20
[01.365]sunxi flash init ok
[01.367]line:724 init_clocks
[01.371]drv_disp_init
[01.380]drv_disp_init finish
[Rx][14:59:28.174] [01.536]Loading Environment from SUNXI_FLASH... [01.540]o
ffset 0x3b58 with sects 0x200 over volume env [0x3b58 0x3d50)
[01.546]get partno from nand_mbr failed: offset 0x3b58 sects 512
*** Warning - read failed, using default environment

Failed (-5)
[01.558]boot_gui_init:start
[Rx][14:59:28.235] partno erro : can't find partition Reserve0
[01.586]Get Reserve0 partition number fail!
[01.593]boot_gui_init:finish
[Rx][14:59:28.251] partno erro : can't find parti
tion bootloader
54 bytes read in 1 ms (52.7 KiB/s)
[01.625]bmp_name=bootlogo.bmp size 38454
38454 bytes read in 5 ms (7.3 MiB/s)
[01.641]sunxi-spinand: check valid secure storage failed with 16 back
[01.647]sunxi-spinand: nand secure storage check page 0 fail
[01.652]sunxi-spinand: check secure storage failed with -22
[01.658]get secure storage map err
[01.661]out of usb burn from boot: not need burn key
[Rx][14:59:28.325] [01.688]update bootcmd
[Rx][14:59:28.381] [01.712]change working_fdt 0x41e8fe70 to 0x41e6fe70
[01.723]## error: update_fdt_dram_para : FDT_ERR_NOTFOUND
[01.732]update dts
Hit any key to stop autoboot:  2 
 1 
 0 
## Error: "distro_bootcmd" not defined