全志在线开发者论坛

NathanLiu

@yelong98 d1s 芯片与 T113-S3 芯片除内核不同以外，其他外设基本相同，直接拉
取 d1 ，然后合并 T113-S3 芯片方案配置就行

NathanLiu

改了一些小问题，把报错去了去，但是我发现在没有插屏幕FPC排线到板子上，我的usb还能用，接上排线之后就用不了了，


[19]HELLO! BOOT0 is starting!
[22]BOOT0 commit : 32dc611
[25]set pll start
[30]periph0 has been enabled
[33]set pll end
[35][pmu]: bus read error
[37]board init ok
[39]ZQ value = 0x30
[41]get_pmu_exist() = -1
[44]ddr_efuse_type: 0xa
[46]trefi:7.8ms
[48][AUTO DEBUG] single rank and full DQ!
[52]ddr_efuse_type: 0xa
[55]trefi:7.8ms
[57][AUTO DEBUG] rank 0 row = 13
[60][AUTO DEBUG] rank 0 bank = 8
[63][AUTO DEBUG] rank 0 page size = 2 KB
[67]DRAM BOOT DRIVE INFO: V0.33
[70]DRAM CLK = 936 MHz
[72]DRAM Type = 3 (2:DDR2,3:DDR3)
[75]DRAMC read ODT  off.
[78]DRAM ODT value: 0x42.
[80]ddr_efuse_type: 0xa
[84]DRAM SIZE =128 M
[85]dram_tpr4:0x0
[87]PLL_DDR_CTRL_REG:0xf8004d00
[90]DRAM_CLK_REG:0xc0000000
[93][TIMING DEBUG] MR2= 0x20
[100]DRAM simple test OK.
[103]rtc standby flag is 0x0, super standby flag is 0x0
[108]dram size =128
[111]card no is 0
[112]sdcard 0 line count 4
[115][mmc]: mmc driver ver 2021-05-21 14:47
[124][mmc]: Wrong media type 0x0
[127][mmc]: ***Try SD card 0***
[137][mmc]: HSSDR52/SDR25 4 bit
[139][mmc]: 50000000 Hz
[142][mmc]: 29820 MB
[144][mmc]: ***SD/MMC 0 init OK!!!***
[230]Loading boot-pkg Succeed(index=0).
[234]Entry_name        = u-boot
[240]Entry_name        = optee
[244]Entry_name        = dtb
[247]mmc not para
[249]Jump to second Boot.
M/TC: OP-TEE version: 6aef7bb2-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Fri Jul 23 09:25:11 UTC 2021 arm
[00.326]smc_tee_inform_fdt failed with: ffff000a
[00.332][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00
[00.337][mmc]: get sdc_type fail and use default host:tm1.
[00.344][mmc]: can't find node "mmc0",will add new node
[00.348][mmc]: fdt err returned <no error>
[00.352][mmc]: Using default timing para
[00.356][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.374][mmc]: card_caps:0x3000000a
[00.377][mmc]: host_caps:0x3000003f
[00.425]Item0 (Map) magic is bad
[00.428]the secure storage item0 copy0 magic is bad
[00.444]Item0 (Map) magic is bad
[00.447]the secure storage item0 copy1 magic is bad
[00.451]Item0 (Map) magic is bad
[00.454]secure storage read widevine fail with:-1
[00.459]secure storage read ec_key fail with:-1
[00.463]secure storage read ec_cert1 fail with:-1
[00.467]secure storage read ec_cert2 fail with:-1
[00.472]secure storage read ec_cert3 fail with:-1
[00.476]secure storage read rsa_key fail with:-1
[00.480]secure storage read rsa_cert1 fail with:-1
[00.485]secure storage read rsa_cert2 fail with:-1
[00.489]secure storage read rsa_cert3 fail with:-1
[00.494]out of usb burn from boot: not need burn key
[01.694]no vendor_boot partition is found
[01.703]Starting kernel ...

[01.705][mmc]: MMC Device 2 not found
[01.709][mmc]: mmc 2 not find, so not exit
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.61 (ubuntu@ubuntu2004) (arm-openwrt-linux-muslgnueabi-gcc.bin (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) 6.4.1, GNU ld (GNU Binutils) 2.27) #186 SMP PREEMPT Sun Aug 25 21:38:59 UTC 2024
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: sun8iw20
[    0.000000] printk: bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 8 MiB at 0x47800000
[    0.000000] On node 0 totalpages: 32768
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] psci: probing for conduit method from DT.
[    0n firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 15 pages/cpu s30348 r8192 d22900 u61440
[    0.000000] pcpu-alloc: s30348 r8192 d22900 u61440 alloc=15*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p5 init=/pseudo_init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:private@mmcblk0p6:rootfs_data@mmcblk0p7:UDISK@mmcblk0p8 cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun8iw20p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.07-00001-gcf16a914-dirty(08/25/2024-18:03:00) androidboot.dramsize=128
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 108584K/131072K available (6144K kernel code, 295K rwdata, 1656K rodata, 1024K init, 1163K bss, 14296K reserved, 8192K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x26c/0x3ec with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.008016] Switching to timer-based delay loop, resolution 41ns
[    0.014194] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.023893] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.034251] pid_max: default: 32768 minimum: 301
[    0.038984] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.046309] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.054634] CPU: Testing write buffer coherency: ok
[    0.059843] /cpus/cpu@0 missing clock-frequency property
[    0.065161] /cpus/cpu@1 missing clock-frequency property
[    0.070499] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.076637] Setting up static identity map for 0x40100000 - 0x40100060
[    0.083303] rcu: Hierarchical SRCU implementation.
[    0.088525] smp: Bringing up secondary CPUs ...
[    0.094139] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.094258] smp: Brought up 1 node, 2 CPUs
[    0.104071] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[    0.110241] CPU: All CPU(s) started in SVC mode.
[    0.115305] devtmpfs: initialized
[    0.129700] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.137817] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.147690] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.154915] pinctrl core: initialized pinctrl subsystem
[    0.161082] NET: Registered protocol family 16
[    0.166964] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.198051] rtc_ccu: sunxi ccu init OK
[    0.204066] ccu: sunxi ccu init OK
[    0.207873] r_ccu: sunxi ccu init OK
[    0.229403] sun6i-dma 3002000.dma-controller: sunxi dma probed
[    0.236638] reg-fixed-voltage vdd-cpu: Fixed regulator specified with variable voltages
[    0.244721] reg-fixed-voltage: probe of vdd-cpu failed with error -22
[    0.251511] iommu: Default domain type: Translated
[    0.256595] sunxi iommu: irq = 24
[    0.260723] SCSI subsystem initialized
[    0.264712] usbcore: registered new interface driver usbfs
[    0.270278] usbcore: registered new interface driver hub
[    0.275660] usbcore: registered new device driver usb
[    0.281529] Advanced Linux Sound Architecture Driver Initialized.
[    0.288371] Bluetooth: Core ver 2.22
[    0.291996] NET: Registered protocol family 31
[    0.296442] Bluetooth: HCI device and connection manager initialized
[    0.302849] Bluetooth: HCI socket layer initialized
[    0.307740] Bluetooth: L2CAP socket layer initialized
[    0.312815] Bluetooth: SCO socket layer initialized
[    0.317954] pwm module init!
[    0.321917] g2d 5410000.g2d: Adding to iommu group 0
[    0.327196] G2D: rcq version initialized.major:251
[    0.332766] clocksource: Switched to clocksource arch_sys_counter
[    0.347130] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver
[    0.356324] NET: Registered protocol family 2
[    0.361255] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.369676] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.377382] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.384452] TCP: Hash tables configured (established 1024 bind 1024)
[    0.390902] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.397465] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.404633] NET: Registered protocol family 1
[    0.409951] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator
[    0.420240] spi spi0: spi0 supply spi not found, using dummy regulator
[    0.426971] sunxi_spi_resource_get()2438 - [spi0] SPI MASTER MODE
[    0.433136] sunxi_spi_resource_get()2476 - Failed to get sample mode
[    0.439490] sunxi_spi_resource_get()2481 - Failed to get sample delay
[    0.445945] sunxi_spi_resource_get()2485 - sample_mode:-1431633921 sample_delay:-1431633921
[    0.454363] sunxi_spi_clk_init()2527 - [spi0] mclk 100000000
[    0.460672] sunxi_spi_probe()2978 - [spi0]: driver probe succeed, base c881f000, irq 39
[    0.470222] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.481553] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.487591] ntfs: driver 2.1.32 [Flags: R/W].
[    0.521229] io scheduler mq-deadline registered
[    0.525805] io scheduler kyber registered
[    0.530782] [DISP]disp_module_init
[    0.534685] disp 5000000.disp: Adding to iommu group 0
[    0.551442] disp 5000000.disp: 5000000.disp supply vcc-lcd not found, using dummy regulator
[    0.560030] disp 5000000.disp: 5000000.disp supply vcc-pd not found, using dummy regulator
[    0.573666] display_fb_request,fb_id:0
[    0.583239] [DISP] Fb_copy_boot_fb,line:1445:
[    0.583243] no boot_fb0
[    0.590486] disp_al_manager_apply ouput_type:0
[    0.593044] [DISP]disp_module_init finish
[    0.595361] [DISP] lcd_clk_config,line:774:
[    0.595372] disp 0, clk: pll(426000000),clk(426000000),dclk(71000000) dsi_rate(71000000)
[    0.595372]      clk real:pll(420000000),clk(420000000),dclk(105000000) dsi_rate(150000000)
[    0.599862] sunxi_sid_init()783 - insmod ok
[    0.624913] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator
[    0.635092] uart uart0: uart0 supply uart not found, using dummy regulator
[    0.642199] uart0: ttyS0 at MMIO 0x2500000 (irq = 34, base_baud = 1500000) is a SUNXI
[    0.650074] sw_console_setup()1807 - console setup baud 115200 parity n bits 8, flow n
[    0.658063] printk: console [ttyS0] enabled
[    0.658063] printk: console [ttyS0] enabled
[    0.666975] printk: bootconsole [earlycon0] disabled
[    0.666975] printk: bootconsole [earlycon0] disabled
[    0.678261] misc dump reg init
[    0.682591] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator
[    0.693790] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9
[    0.701039] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed
[    0.708395] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed
[    0.715836] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1)
[    0.722379] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power.
[    0.729334] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1)
[    0.737081] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1
[    0.744947] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1
[    0.753078] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled
[    0.760702] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power.
[    0.767486] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1)
[    0.775039] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=207 assert=0
[    0.783203] dma-buf: Running sanitycheck
[    0.787602] dma-buf: Running dma_fence
[    0.791802] sizeof(dma_fence)=48
[    0.795573] dma-buf: Running dma_fence/sanitycheck
[    0.800958] dma-buf: Running dma_fence/test_signaling
[    0.806646] dma-buf: Running dma_fence/test_add_callback
[    0.812602] dma-buf: Running dma_fence/test_late_add_callback
[    0.819085] dma-buf: Running dma_fence/test_rm_callback
[    0.824958] dma-buf: Running dma_fence/test_late_rm_callback
[    0.831305] dma-buf: Running dma_fence/test_status
[    0.836690] dma-buf: Running dma_fence/test_error
[    0.841965] dma-buf: Running dma_fence/test_wait
[    0.847155] dma-buf: Running dma_fence/test_wait_timeout
[    0.892778] dma-buf: Running dma_fence/test_stub
[    0.897974] dma-buf: Running dma_fence/race_signal_callback
[    0.973013] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator
[    0.984087] thread_signal_callback[0] completed 37112 passes, 18 misses
[    0.991542] thread_signal_callback[1] completed 37121 passes, 28 misses
[    0.991710] [DISP] disp_device_attached_and_enable,line:233:
[    0.991714] attached ok, mgr0<-->dev0
[    1.009480] [DISP] disp_device_attached_and_enable,line:236:
[    1.009489] type:1,mode:0,fmt:rgb,bits:8bits,eotf:4,cs:0 dvi_hdmi:2, range:2 scan:0 ratio:8
[    1.072795] thread_signal_callback[0] completed 30849 passes, 30849 misses
[    1.080527] thread_signal_callback[1] completed 30882 passes, 30882 misses
[    1.089021] spi-nand: probe of spi0.0 failed with error -5
[    1.095234] Error: Driver 'spi-nand' is already registered, aborting...
[    1.102996] libphy: Fixed MDIO Bus: probed
[    1.108085] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.115440] sunxi-ehci: EHCI SUNXI driver
[    1.120296] get ehci0-controller wakeup-source is fail.
[    1.126295] sunxi ehci0-controller don't init wakeup source
[    1.132552] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xc0b65180, 0x:c8830000, irq_no:37
[    1.144575] [sunxi-ehci0]: Not init ehci0
[    1.149308] get ehci1-controller wakeup-source is fail.
[    1.155309] sunxi ehci1-controller don't init wakeup source
[    1.161565] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xc0b656a0, 0x:c8834000, irq_no:39
[    1.173967] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator
[    1.186256] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller
[    1.193629] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1
[    1.203575] sunxi-ehci 4200000.ehci1-controller: irq 57, io mem 0x04200000
[    1.232788] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00
[    1.241421] hub 1-0:1.0: USB hub found
[    1.245683] hub 1-0:1.0: 1 port detected
[    1.250608] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.257612] sunxi-ohci: OHCI SUNXI driver
[    1.262530] get ohci0-controller wakeup-source is fail.
[    1.268521] sunxi ohci0-controller don't init wakeup source
[    1.274809] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xc0b65410
[    1.284485] [sunxi-ohci0]: Not init ohci0
[    1.289219] get ohci1-controller wakeup-source is fail.
[    1.295214] sunxi ohci1-controller don't init wakeup source
[    1.301467] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xc0b65930
[    1.311368] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator
[    1.323674] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller
[    1.330926] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2
[    1.340869] sunxi-ohci 4200400.ohci1-controller: irq 58, io mem 0x04200400
[    1.417559] hub 2-0:1.0: USB hub found
[    1.421802] hub 2-0:1.0: 1 port detected
[    1.426863] usbcore: registered new interface driver cdc_acm
[    1.433243] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.442333] usbcore: registered new interface driver usb-storage
[    1.450064] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    1.460829] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    1.471909] sunxi-rtc 7090000.rtc: registered as rtc0
[    1.477645] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    1.488302] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:52 UTC (52)
[    1.497313] sunxi-rtc 7090000.rtc: sunxi rtc probed
[    1.503122] i2c /dev entries driver
[    1.507114] sunxi cedar version 1.1
[    1.511185] sunxi-cedar 1c0e000.ve: Adding to iommu group 0
[    1.517549] VE: sunxi_cedar_probe power-domain init!!!
[    1.523334] VE: install start!!!
[    1.523334]
[    1.528835] VE: cedar-ve the get irq is 40
[    1.528835]
[    1.535322] VE: ve_debug_proc_info:(ptrval), data:(ptrval), lock:(ptrval)
[    1.535322]
[    1.544635] VE: install end!!!
[    1.544635]
[    1.549712] VE: sunxi_cedar_probe
[    1.553639] Bluetooth: HCI UART driver ver 2.3
[    1.558625] Bluetooth: HCI UART protocol H4 registered
[    1.564419] Bluetooth: HCI UART protocol BCSP registered
[    1.570676] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10
[    1.579355] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40)
[    1.589249] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8
[    1.595467] sunxi-mmc 4020000.sdmmc: No vmmc regulator found
[    1.601815] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found
[    1.608276] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found
[    1.614735] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found
[    1.621276] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found
[    1.627827] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found
[    1.634379] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found
[    1.641669] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.652855] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator
[    1.673002] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.697255] sunxi-mmc 4020000.sdmmc: detmode:gpio polling
[    1.703352] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.715466] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40)
[    1.725361] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8
[    1.726453] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.731577] sunxi-mmc 4021000.sdmmc: No vmmc regulator found
[    1.749504] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found
[    1.755975] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found
[    1.762435] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found
[    1.762443] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.770272] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.780625] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found
[    1.780631] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found
[    1.805370] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found
[    1.811946] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed
[    1.821328] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.832537] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[    1.846591] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.852708] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.867231] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    1.878828] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    1.879833] sunxi-mmc 4021000.sdmmc: detmode:manually by software
[    1.897439] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[    1.898169] exFAT: Version 1.3.0
[    1.909179] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    1.909233] mmc0: new high speed SDHC card at address 0001
[    1.913335] usbcore: registered new interface driver snd-usb-audio
[    1.919665] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    1.920567] mmcblk0: mmc0:0001 SD 29.1 GiB
[    1.925920] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.936829] NET: Registered protocol family 10
[    1.942812] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.945474] Segment Routing with IPv6
[    1.958307] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    1.961275] NET: Registered protocol family 17
[    1.973539] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    1.976811]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
[    1.983723] Bluetooth: RFCOMM TTY layer initialized
[    1.988473] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    2.012405] Bluetooth: RFCOMM socket layer initialized
[    2.018189] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    2.024979] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    2.032806] Bluetooth: RFCOMM ver 1.11
[    2.040869] Registering SWP/SWPB emulation handler
[    2.060233] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator
[    2.071667] sunxi-i2c sunxi-i2c0: sunxi-i2c0 supply twi not found, using dummy regulator
[    2.081492] sunxi-i2c sunxi-i2c0: probe success
[    2.087036] sunxi-i2c sunxi-i2c1: sunxi-i2c1 supply twi not found, using dummy regulator
[    2.096801] sunxi-i2c sunxi-i2c1: probe success
[    2.103869] otg manager soc@3000000:usbc0@0: soc@3000000:usbc0@0 supply usbc not found, using dummy regulator
[    2.117290] clk: Not disabling unused clocks
[    2.122091] ALSA device list:
[    2.125612] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    2.135323]   No soundcards found.
[    2.135336] alloc_fd: slot 0 not NULL!
[    2.143402] cfg80211: failed to load regulatory.db
[    2.152749] VFS: Mounted root (squashfs filesystem) readonly on device 179:5.
[    2.163145] devtmpfs: mounted
[    2.168378] Freeing unused kernel memory: 1024K
[    2.192919] Run /pseudo_init as init process
mount: mounting none on /dev failed: Resource busy
mount: mounting /dev/by-name/rootfs_data on /overlay failed: Invalid argument
Mount Failed: formating /dev/by-name/rootfs_data to ext4 ...
/pseudo_init: line 403: mkfs.ext4: not found
can't run '/etc/preinit': No such file or directory
mount: mounting proc on /proc failed: Resource busy
mount: mounting tmpfs on /run failed: No such file or directory
hostname: can't open '/etc/hostname': No such file or directory
------run rc.preboot file-----
/etc/init.d/rcS: line 152: mkfs.ext4: not found
------run rc.modules file-----
------run rc.final file-----
amixer: Control default open error: No such device



BusyBox v1.27.2 () built-in shell (ash)

------run profile file-----
 _____  _              __     _
|_   _||_| ___  _ _   |  |   |_| ___  _ _  _ _
  | |   _ |   ||   |  |  |__ | ||   || | ||_'_|
  | |  | || | || _ |  |_____||_||_|_||___||_,_|
  |_|  |_||_|_||_|_|  Tina is Based on OpenWrt!
 ----------------------------------------------
 Tina Linux (Neptune, 61CC0487)
[    2.570615] file system registered
 ----------------------------------------------
Mon Feb  6 00:00:00 GMT 2023
nodev   debugfs
root@TinaLinux:/# [    2.590966] configfs-gadget 4100000.udc-controller: failed to start g1: -19
sh: write error: No such device
[    2.821556] random: fast init done
[    3.653053] sunxi_usb_udc 4100000.udc-controller: 4100000.udc-controller supply udc not found, using dummy regulator
[    3.669176] read descriptors
[    3.672423] read strings
[    3.916342] android_work: sent uevent USB_STATE=CONNECTED
[    4.024823] configfs-gadget gadget: high-speed config #1: c
[    4.031158] android_work: sent uevent USB_STATE=CONFIGURED
[    5.972815] android_work: sent uevent USB_STATE=DISCONNECTED
[    6.044754] android_work: sent uevent USB_STATE=CONNECTED
[    6.152186] configfs-gadget gadget: high-speed config #1: c
[    6.158511] android_work: sent uevent USB_STATE=CONFIGURED
[   15.532811] android_work: sent uevent USB_STATE=DISCONNECTED
[   15.608515] android_work: sent uevent USB_STATE=CONNECTED
[   15.717205] configfs-gadget gadget: high-speed config #1: c
[   15.723521] android_work: sent uevent USB_STATE=CONFIGURED
[   30.902823] android_work: sent uevent USB_STATE=DISCONNECTED
[   30.977845] android_work: sent uevent USB_STATE=CONNECTED
[   31.086930] configfs-gadget gadget: high-speed config #1: c
[   31.093253] android_work: sent uevent USB_STATE=CONFIGURED

NathanLiu

正在找这个，MARK一下

NathanLiu

&twi1 {
	clock-frequency = <400000>;
	pinctrl-0 = <&twi1_pins_a>;
	pinctrl-1 = <&twi1_pins_b>;
	pinctrl-names = "default", "sleep";
	status = "okay";

	ctp@5d {
		compatible = "allwinner,goodix";
		device_type = "ctp";
		reg = <0x5d>;
		status = "okay";
		ctp_name = "gt9xxnew_ts";
		ctp_twi_id = <0x1>;
		ctp_twi_addr = <0x5d>;
		ctp_screen_max_x = <0x1E0>;
		ctp_screen_max_y = <0x1E0>;
		ctp_revert_x_flag = <0x0>;
		ctp_revert_y_flag = <0x0>;
		ctp_exchange_x_y_flag = <0x0>;
		ctp_int_port = <&pio PE 5 GPIO_ACTIVE_HIGH>;
		ctp_wakeup = <&pio PE 4 GPIO_ACTIVE_HIGH>;
	};
}

开启触摸驱动后，并且根据原理图使用了twi1,但是启动时候报错了，如果插上屏幕会导致串口中断，启动不起来，上面报错是将屏幕FPC拆下来看到的。

NathanLiu

@wyljkl 感谢

NathanLiu


root@TinaLinux:/# mount
/dev/root on / type squashfs (ro,relatime)
devtmpfs on /dev type devtmpfs (rw,relatime,size=52288k,nr_inodes=13072,mode=755)
/proc on /proc type proc (rw,relatime)
tmpfs on /tmp type tmpfs (rw,relatime)
sys on /sys type sysfs (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,gid=5,mode=620,ptmxmode=000)
none on /sys/kernel/config type configfs (rw,relatime)
none on /sys/kernel/debug type debugfs (rw,relatime)
adb on /dev/usb-ffs/adb type functionfs (rw,relatime)

调设备时候发现文件系统是只读的导致很多测试不通过