Swain 发布的帖子

@jeffdev 可以用adb shell 进入控制台，就是不能进入UI层

@daizebin 现在看是跑起来了，串口输入也可以，但是进不去UI界面，像是启动有问题，跑不到UI层

[93]HELLO! BOOT0 is starting!
[95]BOOT0 commit : 84b1541181
[98]set pll start
[100]fix vccio detect value:0xc0
[107]periph0 has been enabled
[110]set pll end
[112][pmu]: bus read error
[114]board init ok
[116]ZQ value = 0x30
[118]get_pmu_exist() = -1
[121]DRAM BOOT DRIVE INFO: V0.33
[124]DRAM CLK = 792 MHz
[126]DRAM Type = 3 (2:DDR2,3:DDR3)
[129]DRAMC read ODT  off.
[131]DRAM ODT value: 0x42.
[134]ddr_efuse_type: 0xa
[137]DRAM SIZE =128 M
[139]dram_tpr4:0x0
[141]PLL_DDR_CTRL_REG:0xf8004100
[144]DRAM_CLK_REG:0xc0000000
[147][TIMING DEBUG] MR2= 0x18
[155]DRAM simple test OK.
[157]rtc standby flag is 0x0, super standby flag is 0x0
[162]dram size =128
[165]card no is 2
[166]sdcard 2 line count 4
[169][mmc]: mmc driver ver 2021-05-21 14:47
[178][mmc]: Wrong media type 0x0, but host sdc2, try mmc first
[184][mmc]: ***Try MMC card 2***
[208][mmc]: RMCA OK!
[210][mmc]: mmc 2 bias 0
[213][mmc]: MMC 5.1
[215][mmc]: HSSDR52/SDR25 4 bit
[218][mmc]: 50000000 Hz
[220][mmc]: 3728 MB
[222][mmc]: ***SD/MMC 2 init OK!!!***
[313]Loading boot-pkg Succeed(index=0).
[316]Entry_name        = u-boot
[323]Entry_name        = optee
[327]Entry_name        = dtb
[330]tunning data addr:0x430003e8
[333]Jump to second Boot.
M/TC: OP-TEE version: 8b49ce62-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Fri Aug 12 08:24:15 UTC 2022 arm


U-Boot 2018.07-g895f570-dirty (May 25 2023 - 19:22:55 +0800) Allwinner Technology

[00.385]CPU:   Allwinner Family
[00.388]Model: sun8iw20
[00.390]DRAM:  128 MiB
[00.393]Relocation Offset is: 04ec9000
[00.420]secure enable bit: 0
E/TC:0   fdt_getprop_u32:343 prop trace_level not found
[00.433]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
[00.439]gic: sec monitor mode
sunxi flash map init
[00.445]flash init start
[00.447]workmode = 0,storage type = 2
[00.450][mmc]: mmc driver ver uboot2018:2022-12-07 18:56:00
[00.457][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.482][mmc]: Best spd md: 2-HSDDR52/DDR50, freq: 2-50000000, Bus width: 4
[00.488]sunxi flash init ok
[00.491]line:703 init_clocks
[00.494]drv_disp_init
[00.499]handle_num : 6 
[00.505]drv_disp_init finish
[00.510]Loading Environment from SUNXI_FLASH... OK
[00.523]boot_gui_init:start
[00.526]set disp.dev2_output_type fail. using defval=0
[00.530]**************** LT8912B Init ****************
[00.607]set disp.fb0_rot_used fail. using defval=0
[00.612]set disp.fb0_rot_degree fail. using defval=0
[00.629]boot_gui_init:finish
partno erro : can't find partition bootloader
[00.636]bmp_name=bootlogo.bmp size 38454
[00.649]Item0 (Map) magic is bad
[00.652]the secure storage item0 copy0 magic is bad
[00.660]Item0 (Map) magic is bad
[00.663]the secure storage item0 copy1 magic is bad
[00.668]Item0 (Map) magic is bad
[00.671]out of usb burn from boot: not need burn key
List file under ULI/factory
** Unrecognized filesystem type **
root_partition is rootfs
set root to /dev/mmcblk0p5
[00.686]upda[00.687]LCD open finish
te part info
[00.691]update bootcmd
[00.695]change working_fdt 0x44888e70 to 0x44868e70
[00.700][mmc]: no mmc-hs400-1_8v!
[00.703][mmc]: delete mmc-hs200-1_8v from dtb
[00.707][mmc]: get max-frequency ok 50000000 Hz
disable nand error: FDT_ERR_BADPATH
[00.731]update dts
Hit any key to stop autoboot:  0 
[00.935]no vendor_boot partition is found
Android's image name: sun8i_arm
ERROR: reserving fdt memory region failed (addr=41900000 size=200000)
ERROR: reserving fdt memory region failed (addr=41c00000 size=400000)
ERROR: reserving fdt memory region failed (addr=41b00000 size=100000)
ERROR: reserving fdt memory region failed (addr=44913000 size=7e9000)
[00.973]Starting kernel ...

[00.976][mmc]: mmc exit start
[00.995][mmc]: mmc 2 exit ok
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.61 (yuanzf@yuanzf-PC) (arm-linux-gnueabi-gcc (Linaro GCC 5.3-2016.05) 5.3.1 20160412, GNU ld (Linaro_Binutils-2016.05) 2.25.0 Linaro 2016_02) #3 SMP PREEMPT Thu May 18 09:47:57 CST 2023
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: sun8iw20
[    0.000000] printk: bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 4 MiB at 0x47c00000
[    0.000000] On node 0 totalpages: 32768
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 15 pages/cpu s30912 r8192 d22336 u61440
[    0.000000] pcpu-alloc: s30912 r8192 d22336 u61440 alloc=15*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500C00 clk_ignore_unused initcall_debug=0 console=ttyS3,115200 loglevel=8 root=/dev/mmcblk0p5 init=/sbin/init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:private@mmcblk0p6:UDISK@mmcblk0p7 cma=4M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun8iw20p1 boot_type=2 androidboot.boot_type=2 gpt=1 uboot_message=2018.07-g895f570-dirty(05/25/2023-19:22:55) disp_reserve=8294400,0x44913000 androidboot.dramsize=128 
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 98308K/131072K available (7168K kernel code, 410K rwdata, 2396K rodata, 1024K init, 159K bss, 28668K reserved, 4096K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x24c/0x3cc with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.008017] Switching to timer-based delay loop, resolution 41ns
[    0.014207] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.023974] Console: colour dummy device 80x30
[    0.028444] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.038805] pid_max: default: 32768 minimum: 301
[    0.043564] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.050886] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.059267] CPU: Testing write buffer coherency: ok
[    0.064536] /cpus/cpu@0 missing clock-frequency property
[    0.069865] /cpus/cpu@1 missing clock-frequency property
[    0.075219] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.081490] Setting up static identity map for 0x40100000 - 0x40100060
[    0.088182] rcu: Hierarchical SRCU implementation.
[    0.093303] BOOTEVENT:        93.293332: ON
[    0.097693] smp: Bringing up secondary CPUs ...
[    0.103536] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.103693] smp: Brought up 1 node, 2 CPUs
[    0.113508] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[    0.119679] CPU: All CPU(s) started in SVC mode.
[    0.124850] devtmpfs: initialized
[    0.140920] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.149114] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.158984] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.166091] pinctrl core: initialized pinctrl subsystem
[    0.172745] NET: Registered protocol family 16
[    0.179033] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.214224] rtc_ccu: sunxi ccu init OK
[    0.220561] ccu: sunxi ccu init OK
[    0.224542] r_ccu: sunxi ccu init OK
[    0.266138] sun6i-dma 3002000.dma-controller: sunxi dma probed
[    0.275250] iommu: Default domain type: Translated 
[    0.280378] sunxi iommu: irq = 24
[    0.285033] SCSI subsystem initialized
[    0.289183] usbcore: registered new interface driver usbfs
[    0.294814] usbcore: registered new interface driver hub
[    0.300230] usbcore: registered new device driver usb
[    0.305545] mc: Linux media interface: v0.10
[    0.309915] videodev: Linux video capture interface: v2.00
[    0.316593] Advanced Linux Sound Architecture Driver Initialized.
[    0.323656] pwm module init!
[    0.328074] g2d 5410000.g2d: Adding to iommu group 0
[    0.333452] G2D: rcq version initialized.major:250
[    0.339441] input: sunxi-keyboard as /devices/virtual/input/input0
[    0.346866] clocksource: Switched to clocksource arch_sys_counter
[    0.362305] sun8iw20-pinctrl pio: initialized sunXi PIO driver
[    0.382322] thermal_sys: Registered thermal governor 'step_wise'
[    0.382330] thermal_sys: Registered thermal governor 'user_space'
[    0.388972] NET: Registered protocol family 2
[    0.400217] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.408630] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.416317] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.423420] TCP: Hash tables configured (established 1024 bind 1024)
[    0.429913] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.436459] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.443670] NET: Registered protocol family 1
[    0.450455] Initialise system trusted keyrings
[    0.455078] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.472504] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.478672] ntfs: driver 2.1.32 [Flags: R/W].
[    0.483360] fuse: init (API version 7.31)
[    0.488577] NET: Registered protocol family 38
[    0.493039] Key type asymmetric registered
[    0.497180] Asymmetric key parser 'x509' registered
[    0.502132] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.509680] io scheduler mq-deadline registered
[    0.514224] io scheduler kyber registered
[    0.518381] atomic64_test: passed
[    0.523180] [DISP]disp_module_init
[    0.527192] disp 5000000.disp: Adding to iommu group 0
[    0.532980] [DISP] disp_init,line:2331:
[    0.532986] smooth display screen:0 type:1 mode:4
[    0.558611] display_fb_request,fb_id:0
[    0.583179] disp_al_manager_apply ouput_type:1
[    0.587874] [DISP] lcd_clk_config,line:777:
[    0.587886] disp 0, clk: pll(888000000),clk(888000000),dclk(148000000) dsi_rate(148000000)
[    0.587886]      clk real:pll(888000000),clk(888000000),dclk(222000000) dsi_rate(150000000)
[    0.588262] [DISP]disp_module_init finish
[    0.603111] Freeing logo buffer memory: 8100K
[    0.610200] sunxi_sid_init()783 - insmod ok
[    0.621946] of_pwm_get(): can't parse "pwms" property
[    0.627041] pwm-regulator vdd-cpu: Failed to get PWM: -2
[    0.632388] pwm-regulator: probe of vdd-cpu failed with error -2
[    0.639518] sun8iw20-pinctrl pio: pio supply vcc-pd not found, using dummy regulator
[    0.647827] uart uart3: uart3 supply uart not found, using dummy regulator
[    0.655062] uart3: ttyS3 at MMIO 0x2500c00 (irq = 34, base_baud = 1500000) is a SUNXI
[    0.662957] sw_console_setup()1831 - console setup baud 115200 parity n bits 8, flow n
  0.670935] printk: console [ttyS3] enabled
[    0.670935] printk: console [ttyS3] enabled
[    0.679858] printk: bootconsole [earlycon0] disabled
[    0.679858] printk: bootconsole [earlycon0] disabled
[    0.691409] misc dump reg init
[    0.695324] deinterlace 5400000.deinterlace: Adding to iommu group 0
[    0.702984] deinterlace 5400000.deinterlace: version[1.0.0], ip=0x110
[    0.712754] libphy: Fixed MDIO Bus: probed
[    0.717721] usbcore: registered new interface driver asix
[    0.723826] usbcore: registered new interface driver ax88179_178a
[    0.730717] usbcore: registered new interface driver cdc_ether
[    0.737306] usbcore: registered new interface driver net1080
[    0.743677] usbcore: registered new interface driver cdc_subset
[    0.750366] usbcore: registered new interface driver zaurus
[    0.756665] usbcore: registered new interface driver cdc_ncm
[    0.762995] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.770288] sunxi-ehci: EHCI SUNXI driver
[    0.775095] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.782034] sunxi-ohci: OHCI SUNXI driver
[    0.787098] usbcore: registered new interface driver uas
[    0.793114] usbcore: registered new interface driver usb-storage
[    0.799913] usbcore: registered new interface driver ums-alauda
[    0.806573] usbcore: registered new interface driver ums-cypress
[    0.813350] usbcore: registered new interface driver ums-datafab
[    0.820133] usbcore: registered new interface driver ums_eneub6250
[    0.827099] usbcore: registered new interface driver ums-freecom
[    0.833875] usbcore: registered new interface driver ums-isd200
[    0.840552] usbcore: registered new interface driver ums-jumpshot
[    0.847417] usbcore: registered new interface driver ums-karma
[    0.853977] usbcore: registered new interface driver ums-onetouch
[    0.860861] usbcore: registered new interface driver ums-realtek
[    0.867636] usbcore: registered new interface driver ums-sddr09
[    0.874291] usbcore: registered new interface driver ums-sddr55
[    0.880968] usbcore: registered new interface driver ums-usbat
[    0.887668] usbcore: registered new interface driver option
[    0.893937] usbserial: USB Serial support registered for GSM modem (1-port)
[    0.902510] i2c /dev entries driver
[    0.908727] usbcore: registered new interface driver uvcvideo
[    0.915145] USB Video Class driver (1.1.1)
[    0.919756] gspca_main: v2.14.0 registered
[    0.924323] sunxi cedar version 1.1
[    0.929415] sunxi-wdt 20500a0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    0.940081] sun8iw20-pinctrl pio: pio supply vcc-pc not found, using dummy regulator
[    0.948960] sunxi-mmc 4022000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40)
[    0.958779] sunxi-mmc 4022000.sdmmc: ***ctl-spec-caps*** 308
[    0.965142] sunxi-mmc 4022000.sdmmc: No vmmc regulator found
[    0.971469] sunxi-mmc 4022000.sdmmc: No vqmmc regulator found
[    0.977888] sunxi-mmc 4022000.sdmmc: No vdmmc regulator found
[    0.984295] sunxi-mmc 4022000.sdmmc: No vd33sw regulator found
[    0.990810] sunxi-mmc 4022000.sdmmc: No vd18sw regulator found
[    0.997323] sunxi-mmc 4022000.sdmmc: No vq33sw regulator found
[    1.003827] sunxi-mmc 4022000.sdmmc: No vq18sw regulator found
[    1.010361] sunxi-mmc 4022000.sdmmc: Cann't get pin bias hs pinstate,check if needed
[    1.019920] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.043608] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.067808] sunxi-mmc 4022000.sdmmc: detmode:alway in(non removable)
[    1.074918] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.078211] usbcore: registered new interface driver usbhid
[    1.092799] usbhid: USB HID core driver
[    1.094026] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.097107] exFAT: Version 1.3.0
[    1.097658] sunxi-msgbox 3003000.msgbox: sunxi msgbox driver probe ...
[    1.110180] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.112668] sunxi-msgbox 3003000.msgbox: sunxi msgbox driver init ok...
[    1.138844] rpmsg_tty_init: Sunxi rpmsg tty driver will init
[    1.145245] rpmsg_tty_init: Sunxi rpmsg tty driver init ok
[    1.155361] NET: Registered protocol family 10
[    1.160404] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.160516] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.173053] Segment Routing with IPv6
[    1.187872] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    1.188972] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.195929] NET: Registered protocol family 17
[    1.211130] NET: Registered protocol family 15
[    1.216777] Registering SWP/SWPB emulation handler
[    1.222538] Loading compiled-in X.509 certificates
[    1.228865] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.246729] sunxi-thermal 2009400.ths: sun8iw20 cp version:15
[    1.253969] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01)
[    1.256139] get drvvbus-en is fail, 22
[    1.264072] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01)
[    1.268114] get ehci0-controller wakeup-source is fail.
[    1.277698] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01)
[    1.283623] sunxi ehci0-controller don't init wakeup source
[    1.293242] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01)
[    1.299443] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xc0c84e18, 0x:c8887000, irq_no:30
[    1.299449] [sunxi-ehci0]: Not init ehci0
[    1.321142] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing MMC-HS(SDR20) dt B
[    1.325636] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing MMC-HS(SDR20) dt B
[    1.337751] get drvvbus-en is fail, 22
[    1.353204] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing MMC-HS(SDR20) dt B
[    1.353208] get ohci0-controller wakeup-source is fail.
[    1.353329] sunxi ohci0-controller don't init wakeup source
[    1.377130] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xc0c850c8
[    1.377139] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing MMC-DDR52 dt B
[    1.398133] [sunxi-ohci0]: Not init ohci0
[    1.402734] mmc0: new DDR MMC card at address 0001
[    1.403276] get drvvbus-en is fail, 22
[    1.409616] mmcblk0: mmc0:0001 4FTE4R 3.64 GiB 
[    1.412332] get ehci1-controller wakeup-source is fail.
[    1.417834] mmcblk0rpmb: mmc0:0001 4FTE4R partition 3 512 KiB, chardev (243:0)
[    1.423382] sunxi ehci1-controller don't init wakeup source
[    1.437688] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xc0c85378, 0x:c88a3000, irq_no:32
[    1.450072] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator
[    1.462988]  mmcblk0: p1 p2 p3 p4 p5 p6 p7
[    1.463811] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller
[    1.474834] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1
[    1.484796] sunxi-ehci 4200000.ehci1-controller: irq 50, io mem 0x04200000
[    1.516894] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00
[    1.524679] sunxi-ehci 4200000.ehci1-controller: ehci_irq: highspeed device connect
[    1.534287] hub 1-0:1.0: USB hub found
[    1.538548] hub 1-0:1.0: 1 port detected
[    1.543888] get drvvbus-en is fail, 22
[    1.548114] get ohci1-controller wakeup-source is fail.
[    1.554098] sunxi ohci1-controller don't init wakeup source
[    1.560339] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xc0c85628
[    1.570275] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator
[    1.582560] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller
[    1.589824] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2
[    1.599725] sunxi-ohci 4200400.ohci1-controller: irq 51, io mem 0x04200400
[    1.681862] hub 2-0:1.0: USB hub found
[    1.686120] hub 2-0:1.0: 1 port detected
[    1.692028] otg manager soc@3000000:usbc0@0: soc@3000000:usbc0@0 supply usbc not found, using dummy regulator
[    1.703588] sun8iw20-pinctrl pio: pio supply vcc-pe not found, using dummy regulator
[    1.715130] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    1.726607] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    1.734193] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    1.743847] clk: Not disabling unused clocks
[    1.748785] ALSA device list:
[    1.752092]   No soundcards found.
[    1.755888] alloc_fd: slot 0 not NULL!
[    1.760095] cfg80211: failed to load regulatory.db
[    1.769448] VFS: Mounted root (squashfs filesystem) readonly on device 179:5.
[    1.779462] Freeing unused kernel memory: 1024K
[    1.837039] Kernel init done
[    1.840255] Run /sbin/init as init process
[    1.916960] usb 1-1: new high-speed USB device number 2 using sunxi-ehci
[    2.120268] hub 1-1:1.0: USB hub found
[    2.124830] hub 1-1:1.0: 4 ports detected
[    2.276635] init: Console is alive
[    2.280795] init: - watchdog -
[    2.285005] init: - preinit -
[    2.315889] kmodloader: no module folders for kernel version 5.4.61 found
[    3.035409] random: jshn: uninitialized urandom read (4 bytes read)
[    3.060024] random: jshn: uninitialized urandom read (4 bytes read)
/dev/by-name/UDISK already format by ext4
[    3.417620] mount_root: loading kmods from internal overlay
[    3.432915] kmodloader: no module folders for kernel version 5.4.61 found
[    3.441232] mount_root: failed to launch kmodloader from internal overlay
[    3.488236] block: attempting to load /etc/config/fstab
e2fsck 1.45.6 (20-Mar-2020)
/dev/by-name/UDISK: recovering journal
/dev/by-name/UDISK: clean, 31/228928 files, 34353/914660 blocks
[    3.876367] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: 
[    3.878008] random: procd: uninitialized urandom read (4 bytes read)
[    3.901039] mount_root: switched to extroot
[    5.124192] procd: - early -
[    5.127728] procd: - watchdog -
[    5.286990] 
[    5.286990] insmod_device_driver
[    5.286990] 
[    5.294227] sunxi_usb_udc 4100000.udc-controller: 4100000.udc-controller supply udc not found, using dummy regulator
[    5.331135] procd: - watchdog -
[    5.362520] procd: - ubus -
[    5.440319] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.450510] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.458128] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.470641] procd: - init -
Please press Enter to activate this console.
[    6.520210] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[    6.633156] kmodloader: no module folders for kernel version 5.4.61 found
kmodloader done
[    7.223799] file system registered
[    7.320180] random: fast init done
[    7.351427] configfs-gadget 4100000.udc-controller: failed to start g1: -19
[    7.835885] read descriptors
[    7.841763] read strings
[    8.002414] sunxi_set_cur_vol_work()424 WARN: get power supply failed
[    8.046132] android_work: sent uevent USB_STATE=CONNECTED
[    8.107315] configfs-gadget gadget: high-speed config #1: c
[    8.113794] android_work: sent uevent USB_STATE=CONFIGURED

@whycanservice 没有在升级，已经升级完了，现在我基本把所有外设都关闭了，还是进不去系统

[81]HELLO! BOOT0 is starting!
[83]BOOT0 commit : 84b1541181
[86]set pll start
[88]fix vccio detect value:0xc0
[95]periph0 has been enabled
[98]set pll end
[99][pmu]: bus read error
[102]board init ok
[104]enable_jtag
[105]ZQ value = 0x30
[107]get_pmu_exist() = -1
[110]DRAM BOOT DRIVE INFO: V0.33
[113]DRAM CLK = 792 MHz
[115]DRAM Type = 3 (2:DDR2,3:DDR3)
[118]DRAMC read ODT  off.
[120]DRAM ODT value: 0x42.
[123]ddr_efuse_type: 0xa
[126]DRAM SIZE =128 M
[128]dram_tpr4:0x0
[130]PLL_DDR_CTRL_REG:0xf8004100
[133]DRAM_CLK_REG:0xc0000000
[136][TIMING DEBUG] MR2= 0x18
[144]DRAM simple test OK.
[146]rtc standby flag is 0x0, super standby flag is 0x0
[151]dram size =128
[154]card no is 2
[155]sdcard 2 line count 4
[158][mmc]: mmc driver ver 2021-05-21 14:47
[167][mmc]: Wrong media type 0x0, but host sdc2, try mmc first
[173][mmc]: ***Try MMC card 2***
[197][mmc]: RMCA OK!
[199][mmc]: mmc 2 bias 0
[202][mmc]: MMC 5.1
[204][mmc]: HSSDR52/SDR25 4 bit
[207][mmc]: 50000000 Hz
[209][mmc]: 3728 MB
[211][mmc]: ***SD/MMC 2 init OK!!!***
[302]Loading boot-pkg Succeed(index=0).
[305]Entry_name        = u-boot
[312]Entry_name        = optee
[316]Entry_name        = dtb
[319]tunning data addr:0x430003e8
[322]Jump to second Boot.
M/TC: OP-TEE version: 8b49ce62-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Fri Aug 12 08:24:15 UTC 2022 arm


U-Boot 2018.07-g895f570-dirty (May 11 2023 - 11:34:42 +0800) Allwinner Technology

[00.374]CPU:   Allwinner Family
[00.377]Model: sun8iw20
[00.379]DRAM:  128 MiB
[00.383]Relocation Offset is: 04ec9000
[00.409]secure enable bit: 0
E/TC:0   fdt_getprop_u32:343 prop trace_level not found
[00.422]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
[00.428]gic: sec monitor mode
sunxi flash map init
[00.434]flash init start
[00.436]workmode = 0,storage type = 2
[00.439][mmc]: mmc driver ver uboot2018:2022-12-07 18:56:00
[00.446][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.471][mmc]: Best spd md: 2-HSDDR52/DDR50, freq: 2-50000000, Bus width: 4
[00.477]sunxi flash init ok
[00.480]line:703 init_clocks
[00.483]drv_disp_init
[00.488]handle_num : 6 
[00.494]drv_disp_init finish
[00.499]Loading Environment from SUNXI_FLASH... OK
[00.513]boot_gui_init:start
[00.515]set disp.dev2_output_type fail. using defval=0
[00.592]set disp.fb0_rot_used fail. using defval=0
[00.596]set disp.fb0_rot_degree fail. using defval=0
[00.614]boot_gui_init:finish
partno erro : can't find partition bootloader
[00.621]bmp_name=bootlogo.bmp size 38454
[00.634]Item0 (Map) magic is bad
[00.637]the secure storage item0 copy0 magic is bad
[00.645]Item0 (Map) magic is bad
[00.648]the secure storage item0 copy1 magic is bad
[00.653]Item0 (Map) magic is bad
[00.656]usb burn from boot
delay time 0
weak:otg_phy_config
[00.667]usb prepare ok
[00.672]LCD open finish
[00.970]overtime
[00.973]do_burn_from_boot usb : no usb exist
List file under ULI/factory
** Unrecognized filesystem type **
root_partition is rootfs
set root to /dev/mmcblk0p5
[00.988]update part info
[00.990]update bootcmd
[00.994]change working_fdt 0x44888e70 to 0x44868e70
[00.999][mmc]: no mmc-hs400-1_8v!
[01.002][mmc]: delete mmc-hs200-1_8v from dtb
[01.006][mmc]: get max-frequency ok 50000000 Hz
disable nand error: FDT_ERR_BADPATH
[01.031]update dts
Hit any key to stop autoboot:  0 
[01.240]no vendor_boot partition is found
Android's image name: sun8i_arm
ERROR: reserving fdt memory region failed (addr=41900000 size=200000)
ERROR: reserving fdt memory region failed (addr=41c00000 size=400000)
ERROR: reserving fdt memory region failed (addr=41b00000 size=100000)
ERROR: reserving fdt memory region failed (addr=44913000 size=7e9000)
[01.278]Starting kernel ...

[01.281][mmc]: mmc exit start
[01.300][mmc]: mmc 2 exit ok
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.61 (yuanzf@yuanzf-PC) (arm-linux-gnueabi-gcc (Linaro GCC 5.3-2016.05) 5.3.1 20160412, GNU ld (Linaro_Binutils-2016.05) 2.25.0 Linaro 2016_02) #1 SMP PREEMPT Thu May 11 09:57:03 CST 2023
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: sun8iw20
[    0.000000] printk: bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 4 MiB at 0x47c00000
[    0.000000] On node 0 totalpages: 32768
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 15 pages/cpu s30912 r8192 d22336 u61440
[    0.000000] pcpu-alloc: s30912 r8192 d22336 u61440 alloc=15*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: earlyprintk= clk_ignore_unused initcall_debug=0 console=ttyS3,115200 loglevel=8 root=/dev/mmcblk0p5 init=/init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:private@mmcblk0p6:UDISK@mmcblk0p7 cma=4M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun8iw20p1 boot_type=2 androidboot.boot_type=2 gpt=1 uboot_message=2018.07-g895f570-dirty(05/11/2023-11:34:42) disp_reserve=8294400,0x44913000 androidboot.dramsize=128 
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 98288K/131072K available (7168K kernel code, 418K rwdata, 2508K rodata, 1024K init, 171K bss, 28688K reserved, 4096K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x24c/0x3cc with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.008026] Switching to timer-based delay loop, resolution 41ns
[    0.014211] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.023958] Console: colour dummy device 80x30
[    0.028429] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.038792] pid_max: default: 32768 minimum: 301
[    0.043565] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.050886] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.059247] CPU: Testing write buffer coherency: ok
[    0.064517] /cpus/cpu@0 missing clock-frequency property
[    0.069853] /cpus/cpu@1 missing clock-frequency property
[    0.075225] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.081498] Setting up static identity map for 0x40100000 - 0x40100060
[    0.088184] rcu: Hierarchical SRCU implementation.
[    0.093309] BOOTEVENT:        93.299874: ON
[    0.097708] smp: Bringing up secondary CPUs ...
[    0.103542] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.103694] smp: Brought up 1 node, 2 CPUs
[    0.113513] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[    0.119693] CPU: All CPU(s) started in SVC mode.
[    0.124852] devtmpfs: initialized
[    0.141845] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.150070] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.159972] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.167110] pinctrl core: initialized pinctrl subsystem
[    0.173765] NET: Registered protocol family 16
[    0.180067] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.223577] rtc_ccu: sunxi ccu init OK
[    0.230028] ccu: sunxi ccu init OK
[    0.234076] r_ccu: sunxi ccu init OK
[    0.281610] sun6i-dma 3002000.dma-controller: sunxi dma probed
[    0.290211] iommu: Default domain type: Translated 
[    0.295357] sunxi iommu: irq = 24
[    0.299923] SCSI subsystem initialized
[    0.304093] usbcore: registered new interface driver usbfs
[    0.309719] usbcore: registered new interface driver hub
[    0.315172] usbcore: registered new device driver usb
[    0.320506] mc: Linux media interface: v0.10
[    0.324884] videodev: Linux video capture interface: v2.00
[    0.331504] Advanced Linux Sound Architecture Driver Initialized.
[    0.338336] Bluetooth: Core ver 2.22
[    0.342055] NET: Registered protocol family 31
[    0.346531] Bluetooth: HCI device and connection manager initialized
[    0.353019] Bluetooth: HCI socket layer initialized
[    0.357905] Bluetooth: L2CAP socket layer initialized
[    0.363001] Bluetooth: SCO socket layer initialized
[    0.368166] pwm module init!
[    0.372629] g2d 5410000.g2d: Adding to iommu group 0
[    0.378098] G2D: rcq version initialized.major:250
[    0.383628] input: sunxi-keyboard as /devices/virtual/input/input0
[    0.391303] clocksource: Switched to clocksource arch_sys_counter
[    0.406728] sun8iw20-pinctrl pio: initialized sunXi PIO driver
[    0.426796] thermal_sys: Registered thermal governor 'step_wise'
[    0.426804] thermal_sys: Registered thermal governor 'user_space'
[    0.433437] NET: Registered protocol family 2
[    0.444702] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.453133] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.460796] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.467930] TCP: Hash tables configured (established 1024 bind 1024)
[    0.474443] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.480989] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.488198] NET: Registered protocol family 1
[    0.495130] Initialise system trusted keyrings
[    0.499762] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.517060] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.523244] ntfs: driver 2.1.32 [Flags: R/W].
[    0.527930] fuse: init (API version 7.31)
[    0.562883] NET: Registered protocol family 38
[    0.567338] Key type asymmetric registered
[    0.571510] Asymmetric key parser 'x509' registered
[    0.576505] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.583920] io scheduler mq-deadline registered
[    0.588463] io scheduler kyber registered
[    0.592570] atomic64_test: passed
[    0.597422] [DISP]disp_module_init
[    0.601474] disp 5000000.disp: Adding to iommu group 0
[    0.607277] [DISP] disp_init,line:2331:
[    0.607282] smooth display screen:0 type:1 mode:4
[    0.632367] display_fb_request,fb_id:0
[    0.657339] disp_al_manager_apply ouput_type:1
[    0.662002] [DISP]disp_module_init finish
[    0.662057] [DISP] lcd_clk_config,line:777:
[    0.662070] disp 0, clk: pll(888000000),clk(888000000),dclk(148000000) dsi_rate(148000000)
[    0.662070]      clk real:pll(888000000),clk(888000000),dclk(222000000) dsi_rate(150000000)
[    0.667652] sunxi_sid_init()783 - insmod ok
[    0.692020] pwm-regulator: supplied by regulator-dummy
[    0.698759] sun8iw20-pinctrl pio: pio supply vcc-pg not found, using dummy regulator
[    0.707191] uart uart3: uart3 supply uart not found, using dummy regulator
[    0.714485] uart3: ttyS3 at MMIO 0x2500c00 (irq = 34, base_baud = 1500000) is a SUNXI
[    0.722452] sw_console_setup()1831 - console setup baud 115200 parity n bits 8, flow n
  0.730426] printk: console [ttyS3] enabled
[    0.730426] printk: console [ttyS3] enabled
[    0.739357] printk: bootconsole [earlycon0] disabled
[    0.739357] printk: bootconsole [earlycon0] disabled
[    0.751023] misc dump reg init
[    0.755059] deinterlace 5400000.deinterlace: Adding to iommu group 0
[    0.762727] deinterlace 5400000.deinterlace: version[1.0.0], ip=0x110
[    0.772413] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9
[    0.776249] Freeing logo buffer memory: 8100K
[    0.779656] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed
[    0.791942] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed
[    0.799338] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1)
[    0.805893] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power.
[    0.812839] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1)
[    0.820544] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=111 assert=1
[    0.828493] sun8iw20-pinctrl pio: pio supply vcc-pd not found, using dummy regulator
[    0.837390] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1
[    0.845501] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled
[    0.853179] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power.
[    0.859929] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1)
[    0.867461] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=110 assert=0
[    0.876876] libphy: Fixed MDIO Bus: probed
[    0.881481] CAN device driver interface
[    0.886352] usbcore: registered new interface driver asix
[    0.892566] usbcore: registered new interface driver ax88179_178a
[    0.899429] usbcore: registered new interface driver cdc_ether
[    0.906059] usbcore: registered new interface driver net1080
[    0.912489] usbcore: registered new interface driver cdc_subset
[    0.919155] usbcore: registered new interface driver zaurus
[    0.925523] usbcore: registered new interface driver cdc_ncm
[    0.931874] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.939173] sunxi-ehci: EHCI SUNXI driver
[    0.944070] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.950991] sunxi-ohci: OHCI SUNXI driver
[    0.956142] usbcore: registered new interface driver uas
[    0.962203] usbcore: registered new interface driver usb-storage
[    0.968964] usbcore: registered new interface driver ums-alauda
[    0.975680] usbcore: registered new interface driver ums-cypress
[    0.982475] usbcore: registered new interface driver ums-datafab
[    0.989272] usbcore: registered new interface driver ums_eneub6250
[    0.996248] usbcore: registered new interface driver ums-freecom
[    1.003031] usbcore: registered new interface driver ums-isd200
[    1.009713] usbcore: registered new interface driver ums-jumpshot
[    1.016583] usbcore: registered new interface driver ums-karma
[    1.023182] usbcore: registered new interface driver ums-onetouch
[    1.030053] usbcore: registered new interface driver ums-realtek
[    1.036830] usbcore: registered new interface driver ums-sddr09
[    1.043525] usbcore: registered new interface driver ums-sddr55
[    1.050202] usbcore: registered new interface driver ums-usbat
[    1.056911] usbcore: registered new interface driver option
[    1.063207] usbserial: USB Serial support registered for GSM modem (1-port)
[    1.071986] sunxi_gpadc_init,2151, success
[    1.076871] sunxi_gpadc_setup: get channel scan data failed
[    1.083408] input: sunxi-gpadc0 as /devices/virtual/input/input1
[    1.091173] sunxi-rtc 7090000.rtc: errata__fix_alarm_day_reg_default_value(): ALARM0_DAY_REG=0, set it to 1
[    1.102477] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    1.113272] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    1.124525] sunxi-rtc 7090000.rtc: registered as rtc0
[    1.130213] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    1.140852] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:02 UTC (2)
[    1.149744] sunxi-rtc 7090000.rtc: sunxi rtc probed
[    1.155713] i2c /dev entries driver
[    1.159834] IR NEC protocol handler initialized
[    1.164968] IR RC5(x/sz) protocol handler initialized
[    1.171009] sun8iw20-pinctrl pio: pio supply vcc-pb not found, using dummy regulator
[    1.180007] sunxi-rc-recv 7040000.s_cir: sunxi_irrx_resource_get: get ir protocol failed
[    1.189199] Registered IR keymap rc_map_sunxi
[    1.194251] rc rc0: sunxi-ir as /devices/platform/soc@3000000/7040000.s_cir/rc/rc0
[    1.202945] input: sunxi-ir as /devices/platform/soc@3000000/7040000.s_cir/rc/rc0/s_cir_rx
[    1.215169] usbcore: registered new interface driver uvcvideo
[    1.221645] USB Video Class driver (1.1.1)
[    1.226245] gspca_main: v2.14.0 registered
[    1.230815] sunxi cedar version 1.1
[    1.234948] sunxi-cedar 1c0e000.ve: Adding to iommu group 0
[    1.241246] VE: sunxi_cedar_probe power-domain init!!!
[    1.247006] VE: install start!!!
[    1.247006] 
[    1.252574] VE: cedar-ve the get irq is 40
[    1.252574] 
[    1.259072] VE: ve_debug_proc_info:(ptrval), data:(ptrval), lock:(ptrval)
[    1.259072] 
[    1.268330] VE: install end!!!
[    1.268330] 
[    1.273419] VE: sunxi_cedar_probe
[    1.278497] sunxi-wdt 20500a0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    1.287659] Bluetooth: HCI UART driver ver 2.3
[    1.292681] Bluetooth: HCI UART protocol H4 registered
[    1.300522] sun8iw20-pinctrl pio: pio supply vcc-pc not found, using dummy regulator
[    1.309487] sunxi-mmc 4022000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40)
[    1.319358] sunxi-mmc 4022000.sdmmc: ***ctl-spec-caps*** 308
[    1.325769] sunxi-mmc 4022000.sdmmc: No vmmc regulator found
[    1.332108] sunxi-mmc 4022000.sdmmc: No vqmmc regulator found
[    1.338523] sunxi-mmc 4022000.sdmmc: No vdmmc regulator found
[    1.344958] sunxi-mmc 4022000.sdmmc: No vd33sw regulator found
[    1.351478] sunxi-mmc 4022000.sdmmc: No vd18sw regulator found
[    1.357996] sunxi-mmc 4022000.sdmmc: No vq33sw regulator found
[    1.364523] sunxi-mmc 4022000.sdmmc: No vq18sw regulator found
[    1.371060] sunxi-mmc 4022000.sdmmc: Cann't get pin bias hs pinstate,check if needed
[    1.380662] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.404456] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.428650] sunxi-mmc 4022000.sdmmc: detmode:alway in(non removable)
[    1.435812] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.448714] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40)
[    1.458612] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8
[    1.459649] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.464826] sunxi-mmc 4020000.sdmmc: No vmmc regulator found
[    1.477735] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.482745] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found
[    1.500735] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found
[    1.507175] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found
[    1.513721] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found
[    1.520236] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found
[    1.526774] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.526851] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.538379] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found
[    1.556961] sunxi-mmc 4020000.sdmmc: Got CD GPIO
[    1.562182] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.571730] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.584959] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator
[    1.598597] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.605112] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.633431] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01)
[    1.634226] random: fast init done
[    1.643192] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01)
[    1.647033] sunxi-mmc 4020000.sdmmc: detmode:gpio polling
[    1.656683] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01)
[    1.663297] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40)
[    1.672752] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01)
[    1.682175] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    1.692136] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8
[    1.709107] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing MMC-HS(SDR20) dt B
[    1.709200] sunxi-mmc 4021000.sdmmc: No vmmc regulator found
[    1.727046] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing MMC-HS(SDR20) dt B
[    1.738827] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found
[    1.738836] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing MMC-HS(SDR20) dt B
[    1.757122] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing MMC-DDR52 dt B
[    1.761321] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found
[    1.774935] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found
[    1.781489] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found
[    1.788013] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found
[    1.794571] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found
[    1.794581] mmc0: new DDR MMC card at address 0001
[    1.801129] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed
[    1.807810] mmcblk0: mmc0:0001 4FTE4R 3.64 GiB 
[    1.820715] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.831920] mmcblk0rpmb: mmc0:0001 4FTE4R partition 3 512 KiB, chardev (243:0)
[    1.832147] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[    1.848942]  mmcblk0: p1 p2 p3 p4 p5 p6 p7
[    1.860322] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.884640] sunxi-mmc 4021000.sdmmc: detmode:manually by software
[    1.892345] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 52, RTO !!
[    1.899467] usbcore: registered new interface driver usbhid
[    1.905724] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 52, RTO !!
[    1.912644] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.921332] usbhid: USB HID core driver
[    1.927355] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.928477] exFAT: Version 1.3.0
[    1.942133] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    1.944180] sunxi-msgbox 3003000.msgbox: sunxi msgbox driver probe ...
[    1.951316] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    1.958010] sunxi-msgbox 3003000.msgbox: sunxi msgbox driver init ok...
[    1.965293] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    1.972025] rpmsg_tty_init: Sunxi rpmsg tty driver will init
[    1.979528] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    1.984869] rpmsg_tty_init: Sunxi rpmsg tty driver init ok
[    1.991624] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    2.000726] [AUDIOCODEC][sunxi_codec_parse_params][2437]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1
[    2.000726] 
[    2.025854] [AUDIOCODEC][sunxi_codec_parse_params][2473]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0
[    2.026383] [AUDIOCODEC][sunxi_internal_codec_probe][2634]:codec probe finished
[    2.046140] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present!
[    2.055932] [SNDCODEC][sunxi_card_init][583]:card init finished
[    2.063140] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok
[    2.074245] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input3
[    2.086364] [SNDCODEC][sunxi_card_dev_probe][836]:register card finished
[    2.095233] NET: Registered protocol family 10
[    2.101205] Segment Routing with IPv6
[    2.105361] [SNDCODEC][sunxi_hs_init_work][259]:resume-->report switch
[    2.111422] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    2.121208] NET: Registered protocol family 17
[    2.126494] NET: Registered protocol family 15
[    2.131568] can: controller area network core (rev 20170425 abi 9)
[    2.138569] NET: Registered protocol family 29
[    2.143571] can: raw protocol (rev 20170425)
[    2.148342] can: broadcast manager protocol (rev 20170425 t)
[    2.154683] can: netlink gateway (rev 20190810) max_hops=1
[    2.161358] Bluetooth: RFCOMM TTY layer initialized
[    2.166826] Bluetooth: RFCOMM socket layer initialized
[    2.172647] Bluetooth: RFCOMM ver 1.11
[    2.177601] Registering SWP/SWPB emulation handler
[    2.183413] Loading compiled-in X.509 certificates
[    2.207233] sunxi-i2c 2502c00.twi: 2502c00.twi supply twi not found, using dummy regulator
[    2.217349] sunxi-i2c 2502c00.twi: probe success
[    2.223916] sunxi-thermal 2009400.ths: sun8iw20 cp version:15
[    2.234217] platform 2000c13.pwm3: pinctrl_get failed
[    2.239921] platform 2000c13.pwm3: pinctrl_get failed
[    2.245639] cpu cpu0: _set_opp_voltage: failed to set voltage (950000 950000 950000 mV): -19
[    2.255125] platform 2000c13.pwm3: pinctrl_get failed
[    2.260811] platform 2000c13.pwm3: pinctrl_get failed
[    2.266476] cpu cpu0: _set_opp_voltage: failed to set voltage (950000 950000 950000 mV): -19
[    2.275929] cpufreq: __target_index: Failed to change cpu frequency: -19
[    2.285027] get drvvbus-en is fail, 22
[    2.289228] get ehci0-controller wakeup-source is fail.
[    2.295243] sunxi ehci0-controller don't init wakeup source
[    2.301506] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xc0c894b8, 0x:c88cd000, irq_no:36
[    2.313475] [sunxi-ehci0]: Not init ehci0
[    2.318436] get drvvbus-en is fail, 22
[    2.322655] get ohci0-controller wakeup-source is fail.
[    2.328624] sunxi ohci0-controller don't init wakeup source
[    2.334889] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xc0c89768
[    2.344525] [sunxi-ohci0]: Not init ohci0
[    2.349463] get drvvbus-en is fail, 22
[    2.353681] get ehci1-controller wakeup-source is fail.
[    2.359637] sunxi ehci1-controller don't init wakeup source
[    2.365887] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xc0c89a18, 0x:c88e9000, irq_no:38
[    2.378166] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator
[    2.390755] platform 2000c13.pwm3: pinctrl_get failed
[    2.396523] platform 2000c13.pwm3: pinctrl_get failed
[    2.402223] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller
[    2.409468] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1
[    2.419121] cpu cpu0: _set_opp_voltage: failed to set voltage (950000 950000 950000 mV): -19
[    2.428634] platform 2000c13.pwm3: pinctrl_get failed
[    2.434375] platform 2000c13.pwm3: pinctrl_get failed
[    2.440018] cpu cpu0: _set_opp_voltage: failed to set voltage (950000 950000 950000 mV): -19
[    2.449565] cpufreq: __target_index: Failed to change cpu frequency: -19
[    2.457306] sunxi-ehci 4200000.ehci1-controller: irq 56, io mem 0x04200000
[    2.491324] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00
[    2.499110] sunxi-ehci 4200000.ehci1-controller: ehci_irq: highspeed device connect
[    2.508727] hub 1-0:1.0: USB hub found
[    2.513020] hub 1-0:1.0: 1 port detected
[    2.518434] get drvvbus-en is fail, 22
[    2.522668] get ohci1-controller wakeup-source is fail.
[    2.528655] sunxi ohci1-controller don't init wakeup source
[    2.534933] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xc0c89cc8
[    2.544840] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator
[    2.557173] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller
[    2.564455] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2
[    2.574382] sunxi-ohci 4200400.ohci1-controller: irq 57, io mem 0x04200400
[    2.656286] hub 2-0:1.0: USB hub found
[    2.660575] hub 2-0:1.0: 1 port detected
[    2.667319] otg manager soc@3000000:usbc0@0: soc@3000000:usbc0@0 supply usbc not found, using dummy regulator
[    2.678928] sun8iw20-pinctrl pio: pio supply vcc-pe not found, using dummy regulator
[    2.691789] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    2.703296] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    2.710767] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    2.711421] clk: Not disabling unused clocks
[    2.720444] cfg80211: failed to load regulatory.db
[    2.725182] ALSA device list:
[    2.733852]   #0: audiocodec
[    2.737074] alloc_fd: slot 0 not NULL!
[    2.745879] VFS: Mounted root (squashfs filesystem) readonly on device 179:5.
[    2.755987] Freeing unused kernel memory: 1024K
[    2.801568] Kernel init done
[    2.804793] Run /init as init process
[    2.891404] usb 1-1: new high-speed USB device number 2 using sunxi-ehci
[    3.094569] hub 1-1:1.0: USB hub found
[    3.099239] hub 1-1:1.0: 4 ports detected
[    3.505135] init: Console is alive
[    3.509201] init: - watchdog -
[    3.513505] init: - preinit -
[    3.762819] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.771100] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.137805] random: jshn: uninitialized urandom read (4 bytes read)
[    4.162608] random: jshn: uninitialized urandom read (4 bytes read)
/dev/by-name/UDISK already format by ext4
[    4.523306] mount_root: loading kmods from internal overlay
[    4.539308] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    4.547161] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[    4.596035] block: attempting to load /etc/config/fstab
e2fsck 1.45.6 (20-Mar-2020)
/dev/by-name/UDISK: clean, 35/228928 files, 34356/914660 blocks
[    4.967301] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: 
[    4.967768] random: procd: uninitialized urandom read (4 bytes read)
[    4.984615] block: extroot: UUID mismatch (root: eef28811-39e41115-4ad4edcc-f7d79513, overlay: 0d3ca24a-ca5093d3-1ae52b9c-25239031)
[    5.003680] mount_root: unable to create loop device
[    5.010593] mount_root: no usable overlay filesystem found, using tmpfs overlay
[    6.240784] procd: - early -
[    6.241380] 
[    6.241380] insmod_device_driver
[    6.241380] 
[    6.244281] procd: - watchdog -
[    6.251222] sunxi_usb_udc 4100000.udc-controller: 4100000.udc-controller supply udc not found, using dummy regulator
[    6.471088] procd: - watchdog -
[    6.502329] procd: - ubus -
[    6.581736] random: ubusd: uninitialized urandom read (4 bytes read)
[    6.591866] random: ubusd: uninitialized urandom read (4 bytes read)
[    6.599474] random: ubusd: uninitialized urandom read (4 bytes read)
[    6.609493] procd: - init -
Please press Enter to activate this console.
[    6.990466] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    7.506993] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[    7.617092] kmodloader: loading kernel modules from /etc/modules.d/*
[    7.784071] ======== XRADIO WIFI OPEN ========
[    7.792960] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31   
[    7.799746] [XRADIO] Allocated hw_priv @ (ptrval)
[    7.838006] [ADDR_MGT] get_addr_by_name: t->addr: 
[    7.891453] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
[    7.919721] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
[    8.219636] file system registered
[    8.407880] configfs-gadget 4100000.udc-controller: failed to start g1: -19
[    8.753783] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    8.770477] [XRADIO] Detect SDIO card 1
[    8.782672] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[    8.809423] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    8.867745] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    8.903628] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    8.943014] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    8.972969] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    9.017331] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[    9.043645] mmc2: new high speed SDIO card at address 0001
[    9.063486] read descriptors
[    9.066779] read strings
[    9.095370] [SBUS] XRadio Device:sdio clk=50000000
[    9.111877] [XRADIO] XRADIO_HW_REV 1.0 detected.
[    9.352001] [XRADIO] xradio_update_dpllctrl: DPLL_CTRL Sync=0x01400000.
[    9.459433] [XRADIO] Bootloader complete
[    9.564703] [XRADIO] Firmware completed.
[    9.571664] [WSM] Firmware Label:XR_C09.08.52.73_DBG_02.122 2GHZ HT40 May 18 2021 13:36:09
[    9.589272] [XRADIO] Firmware Startup Done.
[    9.594421] [XRADIO_WRN] enable Multi-Rx!
[    9.602812] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[    9.618779] kmodloader: done loading kernel modules from /etc/modules.d/*
kmodloader done
[   10.529710] random: crng init done
[   10.533523] random: 4 urandom warning(s) missed due to ratelimiting
[   11.178245] ieee80211_do_open: vif_type=2, p2p=0, ch=3, addr=dc:44:6d:7e:7b:8f
[   11.186515] [STA] !!!xradio_vif_setup: id=0, type=2, p2p=0, addr=dc:44:6d:7e:7b:8f
[   11.202944] [AP_WRN] BSS_CHANGED_ASSOC but driver is unjoined.
Trying to connect to SWUpdate...