@yixintai 谢谢，正在对比这里。
只是关于sys_config.fex配置等待文档较少，学习门槛比较陡峭

补充一个信息，使用orage 提供orange pi zero2 的img可以正常启动，但自己编译全志的tina-linux启动失败。

@whycan 32GB

编译了H616 tina-linux sdk，生产镜像成功。烧录emmc卡成功后，系统启动遇到以下问题，请各位解答这是什么错误。

[37]HELLO! BOOT0 is starting!
[40]BOOT0 commit : 3ae35eb
[43]set pll start
[45]periph0 has been enabled
[48]set pll end
[50]unknow PMU
[52]PMU: AXP806
[59]dram para16 invalid use default para
[63]vaild para:1  select dram para0
[66]board init ok
[68]DRAM BOOT DRIVE INFO: V0.648
[71]the chip id is 0x5000
[74]chip id check OK
[76]DRAM_VCC set to 1500 mv
[82]read_calibration error 
[87]read_calibration error 
[93]read_calibration error 
[99]read_calibration error 
[104]read_calibration error 
[110]read_calibration error 
[116]read_calibration error 
[122]read_calibration error 
[127]read_calibration error 
[133]read_calibration error 
[136]retraining final error 
[142][AUTO DEBUG]32bit,1 ranks training success!
[154]DRAM CLK =720 MHZ
[156]DRAM Type =3 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4)
[164]Actual DRAM SIZE =1024 M
[167]DRAM SIZE =1024 MBytes, para1 = 30fa, para2 = 4000000, dram_tpr13 = 6041
[180]DRAM simple test OK.
[182]rtc standby flag is 0x0, super standby flag is 0x0
[188]dram size =1024
[191]card no is 0
[192]sdcard 0 line count 4
[195][mmc]: mmc driver ver 2021-10-12 13:56
[199][mmc]: b mmc 0 bias 0
[207][mmc]: Wrong media type 0x0
[210][mmc]: ***Try SD card 0***
[221][mmc]: HSSDR52/SDR25 4 bit
[224][mmc]: 50000000 Hz
[226][mmc]: 29818 MB
[228][mmc]: ***SD/MMC 0 init OK!!!***
[328]Loading boot-pkg Succeed(index=0).
[331][mmc]: b mmc 0 bias 0
[334]Entry_name        = u-boot
[343]Entry_name        = monitor
[347]Entry_name        = dtbo
[350]Entry_name        = dtb
[353]Jump to second Boot.
NOTICE:  BL3-1: v1.0(debug):05d6c57
NOTICE:  BL3-1: Built : 13:35:35, 2021-10-28
NOTICE:  BL3-1 commit: 8
NOTICE:  cpuidle init version V1.0
ERROR:   Error initializing runtime service tspd_fast
NOTICE:  BL3-1: Preparing for EL3 exit to normal world
NOTICE:  BL3-1: Next image address = 0x4a000000
?OTICE:  BL3-1: Next image spsr = 0x1d3

U-Boot 2018.05-g768449b (Apr 14 2023 - 15:44:12 +0800) Allwinner Technology

[00.398]CPU:   Allwinner Family
[00.401]Model: sun50iw9
I2C:   ready
[00.406]DRAM:  1 GiB
[00.408]Relocation Offset is: 35ebf000
[00.444]secure enable bit: 0
[00.448]pmu_axp152_probe pmic_bus_read fail
[00.452]PMU: AXP806
[00.453]PMU: pmu_axp806 found
[00.459]dcdcc_vol = 960, onoff=1
[00.462]aldo1_vol = 3300, onoff=1
[00.465]bldo1_vol = 1800, onoff=1
[00.469]dcdcd_vol = 1340, onoff=1
[00.472]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=400Mhz
[00.479]init_clocks:finish
[00.481]drv_disp_init
[00.507]HDMI 2.0 driver init start!
[00.515]__clk_enable: clk is null.
[00.518]hdmi cec clk enable failed!
[00.524]drv_disp_init finish
[00.527]gic: sec monitor mode
[00.529]sunxi flash type@1 not support fast burn key
[00.535]boot_gui_init:start
tcon_de_attach:de=0,tcon=2[00.542][HDMI2.0]CEA VIC=16: [00.545]1920x1080p[00.546]@60 Hz [00.548]16:9, [00.549]8-bpp [00.550]YCbCr-444
[00.552]BT709
[00.553]eotf:SDR_LUMINANCE_RANGE
[00.669]switch device: sel=0, type=4, mode=10, format=1, bits=0, eotf=4, cs=257
[00.676]boot_gui_init:finish
[00.679]flash init start
[00.681]workmode = 17,storage type = 1
try card 2
set card number 2
get card number 2
[00.689][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00
[00.695][mmc]: get sdc_type fail and use default host:tm4.
[00.706][mmc]: Is not Boot mode!
[00.709][mmc]: SUNXI SDMMC Controller Version:0x40502
[00.720][mmc]: ************Try SD card 2************
[00.725][mmc]: mmc 2 cmd timeout 100 status 100
[00.729][mmc]: smc 2 err, cmd 8,  RTO
[00.733][mmc]: mmc 2 close bus gating and reset
[00.738][mmc]: mmc 2 cmd timeout 100 status 100
[00.742][mmc]: smc 2 err, cmd 55,  RTO
[00.745][mmc]: mmc 2 close bus gating and reset
[00.750][mmc]: ************Try MMC card 2************
[00.758][mmc]: mmc 2 cmd timeout 100 status 100
[00.762][mmc]: smc 2 err, cmd 1,  RTO
[00.766][mmc]: mmc 2 close bus gating and reset
[00.770][mmc]: Card did not respond to voltage select!
[00.775][mmc]: ************SD/MMC 2 init error!************
[00.780][mmc]: mmc init product failed
MMC init failed
try emmc fail
nand common1 version: v1.17 2021-02-22 16:10
[00.790]NB1 : enter phy init
[00.793][NI]enter rawnand hardward init..
[00.804][NE]rawnand not support chip 0: 06 06 06 06 06 06 06 06
[00.809][NE]rawnand not support chip 1: 06 06 06 06 06 06 06 06
[00.815][NE]rawnand not support chip 2: 06 06 06 06 06 06 06 06
[00.821][NE]rawnand not support chip 3: 06 06 06 06 06 06 06 06
[00.826][NE]no rawnand found!
[00.829][NE]rawnand_channel_init channel@0 chips init fail
[00.834][NI]rawnand hardward init fail
[00.838][NI]---rawnand_dump_clock start---
[00.841][NI]SUNXI_CCM_BASE: 0x03001000
[00.845][NI]nand0 clk: 8300010e
[00.848][NI]nand1 clk: 8300010e
[00.851][NI]nand bus gating reset: 10001
[00.854][NI]mbus cfg: c1000002
[00.857][NI]mbus master clk gating: 25
[00.861][NI]pll_peri0 ctrl: b8003100
[00.864][NI]pll_peri1 ctrl: 88003100
[00.867][NI]---rawnand_dump_clock end---
[00.871][NI]---rawnand_dump_gpio_nand start---
[00.875][NI]SUNXI_PIO_BASE: 0x0300b000
[00.878][NI]pc cfg0: 22222222
[00.881][NI]pc cfg1: 22222222
[00.884][NI]pc cfg2 2
[00.886][NI]pc data: 0
[00.888][NI]pc drv0_lvl: 55555555
[00.891][NI]pc drv1_lvl: 1
[00.893][NI]pc pull_0: 40000440
[00.896][NI]pc pull_1: 1
[00.898][NI]voltage mode select: 0
[00.901][NI]---rawnand_dump_gpio_nand end---
[00.905][NE]nand_physic_init error -1
[00.909]NB1 : nand phy init fail
[00.912]Failed to probe nand flash
try nand fail
SF: Detected mx25l1606e with page size 256 Bytes, erase size 4 KiB, total 2 MiB
[00.930]MMC:	 0
[00.931][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00
[00.937][mmc]: get sdc_type fail and use default host:tm1.
[00.948][mmc]: Using default timing para
[00.952][mmc]: SUNXI SDMMC Controller Version:0x40200
[00.970][mmc]: card_caps:0x3000000a
[00.973][mmc]: host_caps:0x3000003f
[00.978]Loading Environment from SUNXI_FLASH... OK
[00.983]try to burn key
[00.986]out of usb burn from boot: not boot mode
[00.990]Net:   [00.991]Net Initialization Skipped
[00.994]No ethernet found.
Hit any key to stop autoboot:  0 
sunxi work mode=0x11
run card sprite
[01.010]try sprite_led_gpio config
[01.014]sprite_led_gpio start
[01.017]sunxi sprite begin
screen_width = 1280
screen_height = 720
bar x1: 320 y1: 320
bar x2: 960 y2: 400
** Unable to read file font32.sft **
sunxi ui_char info error : unable to open font file font32.sft
ui_char_info.word_size is 32
boot_ui_char: open font failed
firmware name <NULL>
img start = 0x18000
try to read mmc start 98304
read mmc ok
[01.062]firmware probe ok
[01.064]fetch download map
*************DOWNLOAD MAP DUMP************
total download part 4

download part[0] name          :bootloader
download part[0] download file :BOOT-RESOURCE_FE
download part[0] verify file   :VBOOT-RESOURCE_F
download part[0] lenlo         :0x10000
download part[0] addrlo        :0x8000
download part[0] encrypt       :0x0
download part[0] verify        :0x1

download part[1] name          :env
download part[1] download file :ENV_FEX000000000
download part[1] verify file   :VENV_FEX00000000
download part[1] lenlo         :0x8000
download part[1] addrlo        :0x18000
download part[1] encrypt       :0x0
download part[1] verify        :0x1

download part[2] name          :boot
download part[2] download file :BOOT_FEX00000000
download part[2] verify file   :VBOOT_FEX0000000
download part[2] lenlo         :0x10000
download part[2] addrlo        :0x20000
download part[2] encrypt       :0x0
download part[2] verify        :0x1

download part[3] name          :rootfs
download part[3] download file :ROOTFS_FEX000000
download part[3] verify file   :VROOTFS_FEX00000
download part[3] lenlo         :0x40000
download part[3] addrlo        :0x30000
download part[3] encrypt       :0x0
download part[3] verify        :0x1

[01.176]fetch mbr
sunxi sprite error : buffer is smaller than data size
sunxi sprite error : read mbr failed
sunxi sprite error : fetch mbr error
sprite_test - do a sprite test

Usage:
sprite_test NULL