导航

    全志在线开发者论坛

    • 注册
    • 登录
    • 搜索
    • 版块
    • 话题
    • 在线文档
    • 社区主页
    1. 主页
    2. wjp2547532
    W
    • 资料
    • 关注 0
    • 粉丝 0
    • 我的积分 3169
    • 主题 14
    • 帖子 69
    • 最佳 6
    • 群组 0

    wjp2547532LV 6

    @wjp2547532

    3169
    积分
    12
    声望
    21
    资料浏览
    69
    帖子
    0
    粉丝
    0
    关注
    注册时间 最后登录

    wjp2547532 取消关注 关注

    wjp2547532 发布的最佳帖子

    • 回复: 请问下,T113-S3TinaLinux,如何新增文件到根文件系统中

      @nlj_moon 如果提示的错误是缺少依赖库的话可以尝试在package/busybox-init-base-files/Makefile中添加3c2ab2da-41e1-48ed-8076-0bcc7b1f26ad-image.png
      引号中改成你缺少的库名字就行

      发布在 其它全志芯片讨论区
      W
      wjp2547532
    • t113 tina linux 内核开机logo不显示

      打开内核logo模块
      11111.jpg 22222.jpg
      开机屏幕只有背光亮,没有任何图像,打印调试发现fb_prepare_logo(struct fb_info *info, int rotate)函数没有被调用,是我哪里弄错了还是有地方没有配置呢

      发布在 其它全志芯片讨论区
      W
      wjp2547532
    • T113-S3 CAN调试问题

      https://bbs.aw-ol.com/topic/1926/t113-s3-can-linux-下已调通/12?_=1692855551540,按照帖子里的方法进行了修改,但是在执行“ifconfig can0 up”时提示f487b762-579b-452e-9f6a-a32920c7546b-image.png
      查了一下说是要先设置can速率,用“ip link set can0 up type can bitrate 125000”设置提示
      b789b061-5ef7-4647-ad2a-f744cc29e76f-image.png
      应该是ip命令不支持,下载最新iproute2源码交叉编译,提示了一堆错误877a8737-144f-465b-9e96-0627eb5cde1b-image.png
      这个应该怎么改呀;

      网上查了一下可以用另一种方式设置波特率:“echo 250000 > /sys/class/net/can0/can_bittiming/bitrate” ,然而发现我的这个路径下并没有这个文件。。。。。。。。。,
      820ee1ad-a1d3-4851-b2d4-53cd0a9c844b-image.png
      现在搞不懂究竟哪里有问题,有大佬了解么?

      发布在 其它全志芯片讨论区
      W
      wjp2547532
    • 回复: T113-S3 驱动屏幕显示问题

      @aw20221130 https://www.cnblogs.com/hylife/p/17496308.html

      发布在 GUI
      W
      wjp2547532
    • 回复: t113 tina linux 内核开机logo不显示

      开机log

      root@TinaLinux:/# [29]HELLO! BOOT0 is starting!
      [32]BOOT0 commit : 88480af-dirty
      [35]set pll start
      [37]fix vccio detect value:0xc0
      [44]periph0 has been enabled
      [47]set pll end
      [48][pmu]: bus read error
      [51]board init ok
      [53]ZQ value = 0x2f
      [55]get_pmu_exist() = -1
      [57]DRAM BOOT DRIVE INFO: V0.33
      [60]DRAM CLK = 936 MHz
      [62]DRAM Type = 3 (2:DDR2,3:DDR3)
      [65]DRAMC read ODT  off.
      [68]DRAM ODT value: 0x42.
      [70]ddr_efuse_type: 0xa
      [73]DRAM SIZE =128 M
      [75]dram_tpr4:0x0
      [77]PLL_DDR_CTRL_REG:0xf8004d00
      [80]DRAM_CLK_REG:0xc0000000
      [83][TIMING DEBUG] MR2= 0x20
      [90]DRAM simple test OK.
      [92]rtc standby flag is 0x0, super standby flag is 0x0
      [97]dram size =128
      [100]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32
      [105]block from 8 to 32
      [210]Check is correct.
      [212]dma 0x29c0c int is not used yet
      [215]dma 0x29c0c int is free, you do not need to free it again
      [221]Entry_name        = u-boot
      [228]Entry_name        = optee
      [231]Entry_name        = dtb
      [234]Jump to second Boot.
      M/TC: OP-TEE version: 6aef7bb2-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Fri Jul 23 09:25:11 UTC 2021 arm
      
      
      U-Boot 2018.07-ge987def-dirty (May 11 2023 - 16:21:04 +0800) Allwinner Technology
      
      [00.288]CPU:   Allwinner Family
      [00.291]Model: sun8iw20
      I2C:   FDT ERROR:fdt_set_all_pin:[twi0]-->FDT_ERR_BADPATH
      FDT ERROR:fdt_set_all_pin:[twi1]-->FDT_ERR_BADPATH
      ready
      [00.312]DRAM:  128 MiB
      [00.315]Relocation Offset is: 04ecf000
      [00.339]secure enable bit: 0
      [00.341]smc_tee_inform_fdt failed with: ffff000a
      [00.347]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
      [00.353]gic: sec monitor mode
      sunxi flash map init
      [00.358]flash init start
      [00.360]workmode = 0,storage type = 0
      
      device nand0 <nand>, # parts = 4
       #: name                size            offset          mask_flags
       0: boot0               0x00100000      0x00000000      1
       1: uboot               0x00300000      0x00100000      1
       2: secure_storage      0x00100000      0x00400000      1
       3: sys                 0x07b00000      0x00500000      0
      
      active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000
      
      defaults:
      mtdids  : nand0=nand
      mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
      [00.477]ubi0: attaching mtd4
      [00.584]ubi0: scanning is finished
      [00.590]ubi0: attached mtd4 (name "sys", size 123 MiB)
      [00.595]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
      [00.601]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
      [00.607]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
      [00.613]ubi0: good PEBs: 491, bad PEBs: 1, corrupted PEBs: 0
      [00.619]ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128
      [00.625]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
      [00.633]ubi0: available PEBs: 0, total reserved PEBs: 491, PEBs reserved for bad PEB handling: 19
      [00.642]sunxi flash init ok
      [00.644]line:703 init_clocks
      [00.647]drv_disp_init
      fdt get node offset faill: hdmi
      [00.659]drv_disp_init finish
      [00.760]Loading Environment from SUNXI_FLASH... OK
      [00.782]Item0 (Map) magic is bad
      secure storage read widevine fail
      [00.787]secure storage read widevine fail with:-1
      secure storage read ec_key fail
      [00.795]secure storage read ec_key fail with:-1
      secure storage read ec_cert1 fail
      [00.802]secure storage read ec_cert1 fail with:-1
      secure storage read ec_cert2 fail
      [00.809]secure storage read ec_cert2 fail with:-1
      secure storage read ec_cert3 fail
      [00.817]secure storage read ec_cert3 fail with:-1
      secure storage read rsa_key fail
      [00.824]secure storage read rsa_key fail with:-1
      secure storage read rsa_cert1 fail
      [00.832]secure storage read rsa_cert1 fail with:-1
      secure storage read rsa_cert2 fail
      [00.839]secure storage read rsa_cert2 fail with:-1
      secure storage read rsa_cert3 fail
      [00.847]secure storage read rsa_cert3 fail with:-1
      [00.852]out of usb burn from boot: not need burn key
      [00.867]update bootcmd
      [00.880]change working_fdt 0x43e8ee70 to 0x43e6ee70
      [00.895]update dts
      Hit any key to stop autoboot:  0 
      [04.126]no vendor_boot partition is found
      Android's image name: t113-hdp1w
      [04.137]Starting kernel ...
      
      [    0.000000] Booting Linux on physical CPU 0x0
      [    0.000000] Linux version 5.4.61 (root@wjp) (arm-openwrt-linux-muslgnueabi-gcc.bin (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) 6.4.1, GNU ld (GNU Binutils) 2.27) #73 SMP PREEMPT Tue May 16 03:53:36 UTC 2023
      [    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
      [    0.000000] CPU: div instructions available: patching division code
      [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
      [    0.000000] OF: fdt: Machine model: sun8iw20
      [    0.000000] printk: bootconsole [earlycon0] enabled
      [    0.000000] Memory policy: Data cache writealloc
      [    0.000000] cma: Reserved 8 MiB at 0x47800000
      [    0.000000] On node 0 totalpages: 32768
      [    0.000000]   Normal zone: 256 pages used for memmap
      [    0.000000]   Normal zone: 0 pages reserved
      [    0.000000]   Normal zone: 32768 pages, LIFO batch:7
      [    0.000000] psci: probing for conduit method from DT.
      [    0.000000] psci: PSCIv1.0 detected in firmware.
      [    0.000000] psci: Using standard PSCI v0.2 function IDs
      [    0.000000] psci: MIGRATE_INFO_TYPE not supported.
      [    0.000000] psci: SMC Calling Convention v1.0
      [    0.000000] percpu: Embedded 15 pages/cpu s30348 r8192 d22900 u61440
      [    0.000000] pcpu-alloc: s30348 r8192 d22900 u61440 alloc=15*4096
      [    0.000000] pcpu-alloc: [0] 0 [0] 1 
      [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
      [    0.000000] Kernel command line: ubi.mtd=sys ubi.block=0,rootfs earlyprintk=sunxi-uart,0x02500C00 clk_ignore_unused initcall_debug=0 console=ttyS3,115200 loglevel=8 root=/dev/ubiblock0_5 rootfstype=squashfs init=/pseudo_init partitions=mbr@ubi0_0:boot-resource@ubi0_1:env@ubi0_2:env-redund@ubi0_3:boot@ubi0_4:rootfs@ubi0_5:rootfs_data@ubi0_6:user_data@ubi0_7:UDISK@ubi0_8: cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.hardware=sun8iw20p1 boot_type=5 androidboot.boot_type=5 gpt=1 uboot_message=2018.07-ge987def-dirty(05/11/2023-16:21:04) aw-ubi-spinand.ubootblks=24 androidboot.dramsize=128 
      [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
      [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
      [    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
      [    0.000000] Memory: 109620K/131072K available (6144K kernel code, 280K rwdata, 1584K rodata, 1024K init, 1166K bss, 13260K reserved, 8192K cma-reserved)
      [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
      [    0.000000] rcu: Preemptible hierarchical RCU implementation.
      [    0.000000]  Tasks RCU enabled.
      [    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
      [    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
      [    0.000000] random: get_random_bytes called from start_kernel+0x264/0x3e8 with crng_init=0
      [    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
      [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
      [    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
      [    0.008015] Switching to timer-based delay loop, resolution 41ns
      [    0.014174] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
      [    0.023876] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
      [    0.034232] pid_max: default: 32768 minimum: 301
      [    0.038963] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
      [    0.046287] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
      [    0.054598] CPU: Testing write buffer coherency: ok
      [    0.059811] /cpus/cpu@0 missing clock-frequency property
      [    0.065136] /cpus/cpu@1 missing clock-frequency property
      [    0.070465] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
      [    0.076609] Setting up static identity map for 0x40100000 - 0x40100060
      [    0.083270] rcu: Hierarchical SRCU implementation.
      [    0.088481] smp: Bringing up secondary CPUs ...
      [    0.094093] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
      [    0.094208] smp: Brought up 1 node, 2 CPUs
      [    0.104003] SMP: Total of 2 processors activated (96.00 BogoMIPS).
      [    0.110181] CPU: All CPU(s) started in SVC mode.
      [    0.115240] devtmpfs: initialized
      [    0.129613] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
      [    0.137707] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
      [    0.147576] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
      [    0.154801] pinctrl core: initialized pinctrl subsystem
      [    0.161210] NET: Registered protocol family 16
      [    0.167054] DMA: preallocated 256 KiB pool for atomic coherent allocations
      [    0.207866] rtc_ccu: sunxi ccu init OK
      [    0.213944] ccu: sunxi ccu init OK
      [    0.218009] r_ccu: sunxi ccu init OK
      [    0.251342] sun6i-dma 3002000.dma-controller: sunxi dma probed
      [    0.259181] iommu: Default domain type: Translated 
      [    0.265492] sunxi iommu: irq = 24
      [    0.269871] SCSI subsystem initialized
      [    0.273930] usbcore: registered new interface driver usbfs
      [    0.279605] usbcore: registered new interface driver hub
      [    0.285008] usbcore: registered new device driver usb
      [    0.291414] Advanced Linux Sound Architecture Driver Initialized.
      [    0.298153] Bluetooth: Core ver 2.22
      [    0.301843] NET: Registered protocol family 31
      [    0.306299] Bluetooth: HCI device and connection manager initialized
      [    0.312700] Bluetooth: HCI socket layer initialized
      [    0.317592] Bluetooth: L2CAP socket layer initialized
      [    0.322696] Bluetooth: SCO socket layer initialized
      [    0.327868] pwm module init!
      [    0.332100] g2d 5410000.g2d: Adding to iommu group 0
      [    0.337736] G2D: rcq version initialized.major:252
      [    0.343373] clocksource: Switched to clocksource arch_sys_counter
      [    0.357762] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver
      [    0.367387] NET: Registered protocol family 2
      [    0.372272] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
      [    0.380671] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
      [    0.388372] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
      [    0.395459] TCP: Hash tables configured (established 1024 bind 1024)
      [    0.401909] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
      [    0.408485] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
      [    0.415648] NET: Registered protocol family 1
      [    0.421014] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator
      [    0.431334] spi spi0: spi0 supply spi not found, using dummy regulator
      [    0.438097] sunxi_spi_resource_get()2438 - [spi0] SPI MASTER MODE
      [    0.444248] sunxi_spi_resource_get()2476 - Failed to get sample mode
      [    0.450592] sunxi_spi_resource_get()2481 - Failed to get sample delay
      [    0.457051] sunxi_spi_resource_get()2485 - sample_mode:-1431633921 sample_delay:-1431633921
      [    0.465451] sunxi_spi_clk_init()2527 - [spi0] mclk 100000000
      [    0.471759] sunxi_spi_probe()2978 - [spi0]: driver probe succeed, base c881f000, irq 41
      [    0.481599] workingset: timestamp_bits=30 max_order=15 bucket_order=0
      [    0.495543] squashfs: version 4.0 (2009/01/31) Phillip Lougher
      [    0.501561] ntfs: driver 2.1.32 [Flags: R/W].
      [    0.536392] io scheduler mq-deadline registered
      [    0.540923] io scheduler kyber registered
      [    0.546287] [DISP]disp_module_init
      [    0.550238] disp 5000000.disp: Adding to iommu group 0
      [    0.555946] [DISP] parser_disp_init_para,line:1430:
      [    0.555949] of_property_read fb0_width fail
      [    0.576181] disp 5000000.disp: 5000000.disp supply vcc-lcd not found, using dummy regulator
      [    0.584803] disp 5000000.disp: 5000000.disp supply vcc-pd not found, using dummy regulator
      [    0.598417] display_fb_request,fb_id:0
      [    0.604137] [DISP] Fb_copy_boot_fb,line:1445:
      [    0.604141] no boot_fb0
      [    0.611110] rotation hw function is configed as no used
      [    0.616882] disp_al_manager_apply ouput_type:0
      [    0.621676] [DISP] lcd_clk_config,line:774:
      [    0.621686] disp 0, clk: pll(330000000),clk(330000000),dclk(55000000) dsi_rate(330000000)
      [    0.621686]      clk real:pll(324000000),clk(324000000),dclk(54000000) dsi_rate(0)
      [    0.623838] [DISP]disp_module_init finish
      [    0.625946] [DISP] disp_sys_pwm_config,line:509:
      [    0.625949] disp_sys_pwm_Config, handle is NULL!
      [    0.643274] sunxi_sid_init()783 - insmod ok
      [    0.645855] [DISP] disp_sys_pwm_set_polarity,line:528:
      [    0.645858] disp_sys_pwm_Set_Polarity, handle is NULL!
      [    0.651815] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator
      [    0.655911] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator
      [    0.659465] uart uart1: uart1 supply uart not found, using dummy regulator
      [    0.696333] uart1: ttyS1 at MMIO 0x2500400 (irq = 34, base_baud = 1500000) is a SUNXI
      [    0.704934] uart uart3: uart3 supply uart not found, using dummy regulator
      [    0.712106] uart3: ttyS3 at MMIO 0x2500c00 (irq = 35, base_baud = 1500000) is a SUNXI
      [    0.713438] ***********************  LCD_panel_init
      [    0.720041] sw_console_setup()1807 - console setup baud 115200 parity n bits 8, flow n
      [    0.732767] printk: console [ttyS3] enabled
      [    0.732767] printk: console [ttyS3] enabled
      [    0.741685] printk: bootconsole [earlycon0] disabled
      [    0.741685] printk: bootconsole [earlycon0] disabled
      [    0.753154] misc dump reg init
      [    0.757963] [ADDR_MGT] addr_mgt_probe: module version: v1.0.11
      [    0.765179] [ADDR_MGT] addr_mgt_probe: success.
      [    0.770581] dma-buf: Running sanitycheck
      [    0.774993] dma-buf: Running dma_fence
      [    0.779170] sizeof(dma_fence)=48
      [    0.782874] dma-buf: Running dma_fence/sanitycheck
      [    0.788247] dma-buf: Running dma_fence/test_signaling
      [    0.793899] dma-buf: Running dma_fence/test_add_callback
      [    0.799820] dma-buf: Running dma_fence/test_late_add_callback
      [    0.806237] dma-buf: Running dma_fence/test_rm_callback
      [    0.812060] dma-buf: Running dma_fence/test_late_rm_callback
      [    0.818379] dma-buf: Running dma_fence/test_status
      [    0.823728] dma-buf: Running dma_fence/test_error
      [    0.828969] dma-buf: Running dma_fence/test_wait
      [    0.834126] dma-buf: Running dma_fence/test_wait_timeout
      [    0.873387] dma-buf: Running dma_fence/test_stub
      [    0.878552] dma-buf: Running dma_fence/race_signal_callback
      [    0.893407] [DISP] disp_lcd_pwm_enable,line:1271:
      [    0.893410] pwm device hdl is NULL
      [    0.902467] [DISP] disp_sys_gpio_request,line:276:
      [    0.902473] disp_sys_gpio_request failed, gpio_name=lcd_bl_en, gpio=123, value=0, ret=-517
      [    0.917076] [DISP] disp_device_attached_and_enable,line:233:
      [    0.917080] attached ok, mgr0<-->dev0
      [    0.927483] [DISP] disp_device_attached_and_enable,line:236:
      [    0.927491] type:1,mode:0,fmt:rgb,bits:8bits,eotf:4,cs:0 dvi_hdmi:2, range:2 scan:0 ratio:8
      [    0.963375] thread_signal_callback[0] completed 27254 passes, 12024 misses
      [    0.971064] thread_signal_callback[1] completed 15268 passes, 38 misses
      [    1.043397] thread_signal_callback[0] completed 39312 passes, 39312 misses
      [    1.051094] thread_signal_callback[1] completed 39325 passes, 39322 misses
      [    1.059353] sunxi-spinand: AW SPINand MTD Layer Version: 2.3 20211223
      [    1.066638] sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.10 20200306
      [    1.074457] sunxi-spinand-phy: not detect any munufacture from id table
      [    1.081845] sunxi-spinand-phy: get spi-nand Model from fdt fail
      [    1.088474] sunxi-spinand-phy: get phy info from fdt fail
      [    1.094511] sunxi-spinand-phy: not detect munufacture from fdt
      [    1.101084] sunxi-spinand-phy: detect munufacture from id table: Winbond
      [    1.108584] sunxi-spinand-phy: detect spinand id: ff21aaef ffffffff
      [    1.115638] sunxi-spinand-phy: ========== arch info ==========
      [    1.122151] sunxi-spinand-phy: Model:               W25N01GVZEIG
      [    1.128869] sunxi-spinand-phy: Munufacture:         Winbond
      [    1.135093] sunxi-spinand-phy: DieCntPerChip:       1
      [    1.140727] sunxi-spinand-phy: BlkCntPerDie:        1024
      [    1.146656] sunxi-spinand-phy: PageCntPerBlk:       64
      [    1.152386] sunxi-spinand-phy: SectCntPerPage:      4
      [    1.158063] sunxi-spinand-phy: OobSizePerPage:      64
      [    1.163805] sunxi-spinand-phy: BadBlockFlag:        0x0
      [    1.169634] sunxi-spinand-phy: OperationOpt:        0x7
      [    1.175467] sunxi-spinand-phy: MaxEraseTimes:       65000
      [    1.181488] sunxi-spinand-phy: EccFlag:             0x0
      [    1.187318] sunxi-spinand-phy: EccType:             2
      [    1.192944] sunxi-spinand-phy: EccProtectedType:    3
      [    1.198586] sunxi-spinand-phy: ========================================
      [    1.205965] sunxi-spinand-phy: 
      [    1.209460] sunxi-spinand-phy: ========== physical info ==========
      [    1.216361] sunxi-spinand-phy: TotalSize:    128 M
      [    1.221697] sunxi-spinand-phy: SectorSize:   512 B
      [    1.227048] sunxi-spinand-phy: PageSize:     2 K
      [    1.232190] sunxi-spinand-phy: BlockSize:    128 K
      [    1.237536] sunxi-spinand-phy: OOBSize:      64 B
      [    1.242780] sunxi-spinand-phy: ========================================
      [    1.250158] sunxi-spinand-phy: 
      [    1.253668] sunxi-spinand-phy: ========== logical info ==========
      [    1.260464] sunxi-spinand-phy: TotalSize:    128 M
      [    1.265810] sunxi-spinand-phy: SectorSize:   512 B
      [    1.271152] sunxi-spinand-phy: PageSize:     4 K
      [    1.276304] sunxi-spinand-phy: BlockSize:    256 K
      [    1.281639] sunxi-spinand-phy: OOBSize:      128 B
      [    1.286990] sunxi-spinand-phy: ========================================
      [    1.294444] sunxi-spinand-phy: block lock register: 0x00
      [    1.300425] sunxi-spinand-phy: feature register: 0x19
      [    1.306073] sunxi-spinand-phy: sunxi physic nand init end
      [    1.312442] Creating 4 MTD partitions on "sunxi_mtd_nand":
      [    1.318604] 0x000000000000-0x000000100000 : "boot0"
      [    1.334288] 0x000000100000-0x000000400000 : "uboot"
      [    1.344348] 0x000000400000-0x000000500000 : "secure_storage"
      [    1.364330] 0x000000500000-0x000008000000 : "sys"
      [    1.369850] random: fast init done
      [    1.464574] sunxi-spinand-phy: phy blk 921 is bad
      [    1.484935] libphy: Fixed MDIO Bus: probed
      [    1.490694] gmac-power0: NULL
      [    1.494088] gmac-power1: NULL
      [    1.497394] gmac-power2: NULL
      [    1.500843] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator
      [    1.512961] Failed to alloc md5
      [    1.516529] eth0: Use random mac address
      [    1.521192] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
      [    1.528493] sunxi-ehci: EHCI SUNXI driver
      [    1.533459] get ehci1-controller wakeup-source is fail.
      [    1.539385] sunxi ehci1-controller don't init wakeup source
      [    1.545620] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xc0b62628, 0x:c8837000, irq_no:3c
      [    1.557589] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply drvvbus not found, using dummy regulator
      [    1.570055] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator
      [    1.582197] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller
      [    1.589435] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1
      [    1.599332] sunxi-ehci 4200000.ehci1-controller: irq 60, io mem 0x04200000
      [    1.633448] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00
      [    1.642074] hub 1-0:1.0: USB hub found
      [    1.646328] hub 1-0:1.0: 1 port detected
      [    1.651342] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
      [    1.658309] sunxi-ohci: OHCI SUNXI driver
      [    1.663269] get ohci1-controller wakeup-source is fail.
      [    1.669219] sunxi ohci1-controller don't init wakeup source
      [    1.675465] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xc0b628b8
      [    1.685126] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply drvvbus not found, using dummy regulator
      [    1.697591] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator
      [    1.709737] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller
      [    1.716983] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2
      [    1.726814] sunxi-ohci 4200400.ohci1-controller: irq 61, io mem 0x04200400
      [    1.808241] hub 2-0:1.0: USB hub found
      [    1.812465] hub 2-0:1.0: 1 port detected
      [    1.817614] usbcore: registered new interface driver usb-storage
      [    1.824513] i2c /dev entries driver
      [    1.828491] sunxi cedar version 1.1
      [    1.832568] sunxi-cedar 1c0e000.ve: Adding to iommu group 0
      [    1.838899] VE: sunxi_cedar_probe power-domain init!!!
      [    1.844646] VE: install start!!!
      [    1.844646] 
      [    1.850189] VE: cedar-ve the get irq is 42
      [    1.850189] 
      [    1.856611] VE: ve_debug_proc_info:(ptrval), data:(ptrval), lock:(ptrval)
      [    1.856611] 
      [    1.865862] VE: install end!!!
      [    1.865862] 
      [    1.870908] VE: sunxi_cedar_probe
      [    1.874886] Bluetooth: HCI UART driver ver 2.3
      [    1.879864] Bluetooth: HCI UART protocol H4 registered
      [    1.885615] Bluetooth: HCI UART protocol BCSP registered
      [    1.891792] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10
      [    1.901022] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40)
      [    1.910877] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8
      [    1.917100] sunxi-mmc 4020000.sdmmc: No vmmc regulator found
      [    1.923426] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found
      [    1.929831] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found
      [    1.936251] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found
      [    1.942753] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found
      [    1.949264] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found
      [    1.955783] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found
      [    1.962704] sunxi-mmc 4020000.sdmmc: Got CD GPIO
      [    1.968068] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail
      [    1.974715] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
      [    1.985823] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator
      [    2.005929] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
      [    2.030285] sunxi-mmc 4020000.sdmmc: detmode:gpio irq
      [    2.035969] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
      [    2.047498] sun8iw20-pinctrl 2000000.pinctrl: pin PG0 already requested by 4500000.eth; cannot claim for 4021000.sdmmc
      [    2.059480] sun8iw20-pinctrl 2000000.pinctrl: pin-192 (4021000.sdmmc) status -22
      [    2.067760] sun8iw20-pinctrl 2000000.pinctrl: could not request pin 192 (PG0) from group PG0  on device 2000000.pinctrl
      [    2.079804] sunxi-mmc 4021000.sdmmc: Error applying setting, reverse things back
      [    2.088094] sunxi-mmc: probe of 4021000.sdmmc failed with error -22
      [    2.095923] exFAT: Version 1.3.0
      [    2.102027] [AUDIOCODEC][sunxi_codec_parse_params][2437]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1
      [    2.102027] 
      [    2.119201] [AUDIOCODEC][sunxi_codec_parse_params][2473]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0
      [    2.130529] [AUDIOCODEC][sunxi_internal_codec_probe][2634]:codec probe finished
      [    2.139670] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present!
      [    2.149471] [SNDCODEC][sunxi_card_init][583]:card init finished
      [    2.156559] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok
      [    2.167480] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input0
      [    2.179444] [SNDCODEC][sunxi_card_dev_probe][836]:register card finished
      [    2.187955] NET: Registered protocol family 10
      [    2.193423] [SNDCODEC][sunxi_hs_init_work][259]:resume-->report switch
      [    2.201403] Segment Routing with IPv6
      [    2.205617] NET: Registered protocol family 17
      [    2.210726] Bluetooth: RFCOMM TTY layer initialized
      [    2.216268] Bluetooth: RFCOMM socket layer initialized
      [    2.222022] Bluetooth: RFCOMM ver 1.11
      [    2.226848] Registering SWP/SWPB emulation handler
      [    2.246663] sun8iw20-pinctrl 2000000.pinctrl: pin PG0 already requested by 4500000.eth; cannot claim for 4021000.sdmmc
      [    2.258675] sun8iw20-pinctrl 2000000.pinctrl: pin-192 (4021000.sdmmc) status -22
      [    2.266946] sun8iw20-pinctrl 2000000.pinctrl: could not request pin 192 (PG0) from group PG0  on device 2000000.pinctrl
      [    2.278990] sunxi-mmc 4021000.sdmmc: Error applying setting, reverse things back
      [    2.287279] sunxi-mmc: probe of 4021000.sdmmc failed with error -22
      [    2.294693] sunxi-i2c sunxi-i2c2: sunxi-i2c2 supply twi not found, using dummy regulator
      [    2.305152] sunxi-i2c sunxi-i2c2: probe success
      [    2.310576] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator
      [    2.321944] sunxi-i2c sunxi-i2c3: sunxi-i2c3 supply twi not found, using dummy regulator
      [    2.354647] sunxi-i2c sunxi-i2c3: SLA+W has been transmitted; ACK not received
      [    2.362708] sunxi-i2c sunxi-i2c3: engine mode: I2C BUS error state is 0x20
      [    2.370449] sunxi-i2c sunxi-i2c3: engine-mode: bus state: 0xf9, isn't idle
      [    2.378112] sunxi-i2c sunxi-i2c3: STOP failed!
      [    2.383082] sunxi-i2c sunxi-i2c3: engine-mode: xfer failed(dev addr:0x50)
      [    2.414707] sunxi-i2c sunxi-i2c3: SLA+W has been transmitted; ACK not received
      [    2.422761] sunxi-i2c sunxi-i2c3: engine mode: I2C BUS error state is 0x20
      [    2.430501] sunxi-i2c sunxi-i2c3: engine-mode: bus state: 0xf9, isn't idle
      [    2.438163] sunxi-i2c sunxi-i2c3: STOP failed!
      [    2.443130] sunxi-i2c sunxi-i2c3: engine-mode: xfer failed(dev addr:0x50)
      [    2.452422] sunxi-i2c sunxi-i2c3: probe success
      [    2.459993] get ehci0-controller wakeup-source is fail.
      [    2.465943] sunxi ehci0-controller don't init wakeup source
      [    2.472161] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xc0b62108, 0x:c88ab000, irq_no:3a
      [    2.484098] [sunxi-ehci0]: Not init ehci0
      [    2.488929] get ohci0-controller wakeup-source is fail.
      [    2.494872] sunxi ohci0-controller don't init wakeup source
      [    2.501089] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xc0b62398
      [    2.510700] [sunxi-ohci0]: Not init ohci0
      [    2.515755] ubi0: attaching mtd3
      [    2.704489] ubi0: scanning is finished
      [    2.716591] ubi0: attached mtd3 (name "sys", size 123 MiB)
      [    2.722715] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
      [    2.730424] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
      [    2.738003] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
      [    2.745780] ubi0: good PEBs: 491, bad PEBs: 1, corrupted PEBs: 0
      [    2.752475] ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128
      [    2.760540] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
      [    2.769859] ubi0: available PEBs: 0, total reserved PEBs: 491, PEBs reserved for bad PEB handling: 19
      [    2.780165] ubi0: background thread "ubi_bgt0d" started, PID 885
      [    2.788122] block ubiblock0_5: created from ubi0:5(rootfs)
      [    2.794795] otg manager soc@3000000:usbc0@0: soc@3000000:usbc0@0 supply usbc not found, using dummy regulator
      [    2.808367] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
      [    2.813444] clk: Not disabling unused clocks
      [    2.818066] cfg80211: failed to load regulatory.db
      [    2.822732] ALSA device list:
      [    2.831482]   #0: audiocodec
      [    2.834734] alloc_fd: slot 0 not NULL!
      [    2.841778] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
      [    2.851697] devtmpfs: mounted
      [    2.856936] Freeing unused kernel memory: 1024K
      [    2.893521] Run /pseudo_init as init process
      mount: mounting none on /dev failed: Resource busy
      [    3.073457] UBIFS (ubi0:6): Mounting in unauthenticated mode
      [    3.079915] UBIFS (ubi0:6): background thread "ubifs_bgt0_6" started, PID 924
      [    3.113742] random: crng init done
      [    3.133811] UBIFS (ubi0:6): recovery needed
      [    3.264749] UBIFS (ubi0:6): recovery completed
      [    3.269907] UBIFS (ubi0:6): UBIFS: mounted UBI device 0, volume 6, name "rootfs_data"
      [    3.278705] UBIFS (ubi0:6): LEB size: 258048 bytes (252 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
      [    3.289785] UBIFS (ubi0:6): FS size: 18579456 bytes (17 MiB, 72 LEBs), journal size 2064385 bytes (1 MiB, 6 LEBs)
      [    3.301252] UBIFS (ubi0:6): reserved for root: 877552 bytes (856 KiB)
      [    3.308501] UBIFS (ubi0:6): media format: w5/r0 (latest is w5/r0), UUID 7DFEE526-6D59-44C4-966D-D42EB2FDEFDF, small LPT model
      can't run '/etc/preinit': No such file or directory
      mount: mounting proc on /proc failed: Resource busy
      hostname: can't open '/etc/hostname': No such file or directory
      ------run rc.preboot file-----
      [    3.463549] UBIFS (ubi0:8): Mounting in unauthenticated mode
      [    3.470017] UBIFS (ubi0:8): background thread "ubifs_bgt0_8" started, PID 954
      [    3.519820] UBIFS (ubi0:8): recovery needed
      [    3.555368] UBIFS (ubi0:8): recovery completed
      [    3.560523] UBIFS (ubi0:8): UBIFS: mounted UBI device 0, volume 8, name "UDISK"
      [    3.568709] UBIFS (ubi0:8): LEB size: 258048 bytes (252 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
      [    3.579800] UBIFS (ubi0:8): FS size: 10838016 bytes (10 MiB, 42 LEBs), journal size 2064385 bytes (1 MiB, 6 LEBs)
      [    3.591270] UBIFS (ubi0:8): reserved for root: 511905 bytes (499 KiB)
      [    3.598473] UBIFS (ubi0:8): media format: w5/r0 (latest is w5/r0), UUID B548A428-6B73-4B42-BE7C-E697D7E1A575, small LPT model
      ------run rc.modules file-----
      [    3.709972] sunxi_gpadc_init,2151, success
      [    3.766035] ======== XRADIO WIFI OPEN ========
      [    3.771527] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31   
      [    3.778309] [XRADIO] Allocated hw_priv @ 767e2611
      [    3.884166] [XRADIO] Detect SDIO card 0
      [    6.053511] [XRADIO] Remove SDIO card 0
      [    6.067791] [SBUS_ERR] sdio probe timeout!
      [    6.072353] [XRADIO_ERR] sbus_sdio_init failed
      [    6.077607] xradio_core_init failed (-110)!
      [    6.201949] ======== XRADIO WIFI OPEN ========
      [    6.207467] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31   
      [    6.214226] [XRADIO] Allocated hw_priv @ ab98aef0
      [    6.320098] [XRADIO] Detect SDIO card 0
      [    6.393659] sunxi_usb_udc 4100000.udc-controller: 4100000.udc-controller supply udc not found, using dummy regulator
      [    8.453532] [XRADIO] Remove SDIO card 0
      [    8.467814] [SBUS_ERR] sdio probe timeout!
      [    8.472377] [XRADIO_ERR] sbus_sdio_init failed
      [    8.477676] xradio_core_init failed (-110)!
      insmod: can't insert '/lib/modules/5.4.61/xr829.ko': Operation timed out
      Successfully initialized wpa_supplicant
      Could not read interface wlan0 flags: No such device
      nl80211: Driver does not support authentication/association or connect commands
      nl80211: deinit ifname=wlan0 disabled_11b_rates=0
      Could not read interface wlan0 flags: No such device
      wlan0: Failed to initialize driver interface
      ------run rc.final file-----
      numid=30,iface=MIXER,name='Headphone Switch'
        ; type=BOOLEAN,access=rw------,values=1
        : values=on
      ------light up RGB LED-----
      /etc/init.d/rcS: /etc/init.d/rc.final: line 15: can't create /sys/class/leds/sunxi_led0r/brightness: nonexistent directory
      /etc/init.d/rcS: /etc/init.d/rc.final: line 16: can't create /sys/class/leds/sunxi_led1g/brightness: nonexistent directory
      /etc/init.d/rcS: /etc/init.d/rc.final: line 17: can't create /sys/class/leds/sunxi_led2b/brightness: nonexistent directory
      /etc/init.d/rcS: /etc/init.d/rc.final: line 21: can't create /sys/class/leds/sunxi_led0r/brightness: nonexistent directory
      /etc/init.d/rcS: /etc/init.d/rc.final: line 22: can't create /sys/class/leds/sunxi_led0g/brightness: nonexistent directory
      /etc/init.d/rcS: /etc/init.d/rc.final: line 23: can't create /sys/class/leds/sunxi_led0b/brightness: nonexistent directory
      /etc/init.d/rcS: /etc/init.d/rc.final: line 24: can't create /sys/class/leds/sunxi_led1r/brightness: nonexistent directory
      /etc/init.d/rcS: /etc/init.d/rc.final: line 25: can't create /sys/class/leds/sunxi_led1g/brightness: nonexistent directory
      /etc/init.d/rcS: /etc/init.d/rc.final: line 26: can't create /sys/class/leds/sunxi_led1b/brightness: nonexistent directory
      /etc/init.d/rcS: /etc/init.d/rc.final: line 27: can't create /sys/class/leds/sunxi_led2r/brightness: nonexistent directory
      /etc/init.d/rcS: /etc/init.d/rc.final: line 2[    9.944707] block ubiblock0_7: created from ubi0:7(user_data)
      8: can't create /sys/class/leds/sunxi_led2g/brightness: nonexistent directory
      /etc/init.d/rcS: /etc/init.d/rc.final: line 29: c[    9.957531] /dev/ubiblock0_7: Can't open blockdev
      an't create /sys/class/leds/sunxi_led2b/brightness: nonexistent directory
      ------light up LED-----
      
      
      BusyBox v1.27.2 () built-in shell (ash)
      
      ------run profile file-----
       _____  _              __     _
      |_   _||_| ___  _ _   |  |   |_| ___  _ _  _ _
        | |   _ |   ||   |  |  |__ | ||   || | ||_'_|
        | |  | || | || _ |  |_____||_||_|_||___||_,_|
        |_|  |_||_|_||_|_|  Tina is Based on OpenWrt!
       ----------------------------------------------
       Tina Linux (Neptune, 61CC0487)
       ----------------------------------------------
      Wed Jun  1 00:00:00 GMT 2022
      nodev   debugfs
      
      发布在 其它全志芯片讨论区
      W
      wjp2547532
    • 回复: t113 tina linux 内核开机logo不显示

      @zh834773979 解决了,tina的logo流程跟标准流程不太一样,首先uboot的设备树中LCD和DISP相关配置要正确,然后在lichee/brandy-2.0/u-boot-2018/configs/sun8iw20p1_uart3_defconfig配置文件中打开下面几个配置0f747a8e-88e2-4a83-9104-26968ccbed17-image.png 应该就可以了

      发布在 其它全志芯片讨论区
      W
      wjp2547532

    wjp2547532 发布的最新帖子

    • F1C200S RGB管脚驱动能力问题

      请教下,F1C200S的管脚驱动能力是否可以配置,目前产品的RGB管脚没加电容,导致电磁兼容测试不过,现在想通过调节管脚驱动能力来改善下,有大佬知道吗?

      发布在 H/F/TV Series
      W
      wjp2547532
    • T113-S3 tina,如何更新logo图片

      因为用户有贴牌需求,请问有没有可以单独更新logo图片的办法

      发布在 其它全志芯片讨论区
      W
      wjp2547532
    • 回复: G2D uboot阶段 logo 旋转不了?怎么办?

      @zllfdd https://codeleading.com/article/55242723616/

      发布在 Linux
      W
      wjp2547532
    • 回复: T113-S3 CAN调试问题

      @zzz123 还是编译iproute2,有一些头文件重复定义的去把编译器里的改掉就好了,不用全部编译完,能把ip命令编译出来就好

      发布在 其它全志芯片讨论区
      W
      wjp2547532
    • T113-S3 CAN调试问题

      https://bbs.aw-ol.com/topic/1926/t113-s3-can-linux-下已调通/12?_=1692855551540,按照帖子里的方法进行了修改,但是在执行“ifconfig can0 up”时提示f487b762-579b-452e-9f6a-a32920c7546b-image.png
      查了一下说是要先设置can速率,用“ip link set can0 up type can bitrate 125000”设置提示
      b789b061-5ef7-4647-ad2a-f744cc29e76f-image.png
      应该是ip命令不支持,下载最新iproute2源码交叉编译,提示了一堆错误877a8737-144f-465b-9e96-0627eb5cde1b-image.png
      这个应该怎么改呀;

      网上查了一下可以用另一种方式设置波特率:“echo 250000 > /sys/class/net/can0/can_bittiming/bitrate” ,然而发现我的这个路径下并没有这个文件。。。。。。。。。,
      820ee1ad-a1d3-4851-b2d4-53cd0a9c844b-image.png
      现在搞不懂究竟哪里有问题,有大佬了解么?

      发布在 其它全志芯片讨论区
      W
      wjp2547532
    • 回复: T113-S3 驱动屏幕显示问题

      @aw20221130 https://www.cnblogs.com/hylife/p/17496308.html

      发布在 GUI
      W
      wjp2547532
    • 回复: 请问下,T113-S3TinaLinux,如何新增文件到根文件系统中

      @nlj_moon 如果提示的错误是缺少依赖库的话可以尝试在package/busybox-init-base-files/Makefile中添加3c2ab2da-41e1-48ed-8076-0bcc7b1f26ad-image.png
      引号中改成你缺少的库名字就行

      发布在 其它全志芯片讨论区
      W
      wjp2547532
    • 回复: t113 tina linux 内核开机logo不显示

      @zh834773979 解决了,tina的logo流程跟标准流程不太一样,首先uboot的设备树中LCD和DISP相关配置要正确,然后在lichee/brandy-2.0/u-boot-2018/configs/sun8iw20p1_uart3_defconfig配置文件中打开下面几个配置0f747a8e-88e2-4a83-9104-26968ccbed17-image.png 应该就可以了

      发布在 其它全志芯片讨论区
      W
      wjp2547532
    • 回复: T113-S3 SD卡启动问题

      @whycanservice2 好的大佬,感谢解惑,多谢

      发布在 其它全志芯片讨论区
      W
      wjp2547532
    • 回复: T113-S3 SD卡启动问题

      @whycanservice2 自制的。为什么插上SD卡就会重启呢?还有就是为什么我插上一张全新的SD卡然后上电,可以正常从spi-nand启动,SD卡也可以正常挂载;但是我插上另一张曾制作成量产卡或启动卡,但是又通过DiskGenius.exe这个工具格式化后的SD卡后上电,好像还是要从SD卡启动。难道是格式化的不完全么?下面是启动信息:

      [141]HELLO! BOOT0 is starting!
      [143]BOOT0 commit : 88480af-dirty
      [147]set pll start
      [153]periph0 has been enabled
      [156]set pll end
      [157][pmu]: bus read error
      [160]board init ok
      [162]ZQ value = 0x2e
      [164]get_pmu_exist() = -1
      [166]ddr_efuse_type: 0xa
      [169]trefi:7.8ms
      [171][AUTO DEBUG] single rank and full DQ!
      [175]ddr_efuse_type: 0xa
      [178]trefi:7.8ms
      [180][AUTO DEBUG] rank 0 row = 13 
      [183][AUTO DEBUG] rank 0 bank = 8 
      [186][AUTO DEBUG] rank 0 page size = 2 KB 
      [190]DRAM BOOT DRIVE INFO: V0.33
      [194]DRAM CLK = 936 MHz
      [196]DRAM Type = 3 (2:DDR2,3:DDR3)
      [199]DRAMC read ODT  off.
      [202]DRAM ODT value: 0x42.
      [204]ddr_efuse_type: 0xa
      [207]DRAM SIZE =128 M
      [209]dram_tpr4:0x0
      [211]PLL_DDR_CTRL_REG:0xf8004d00
      [214]DRAM_CLK_REG:0xc0000000
      [217][TIMING DEBUG] MR2= 0x20
      [225]DRAM simple test OK.
      [227]rtc standby flag is 0x0, super standby flag is 0x0
      [232]dram size =128
      [235]card no is 0
      [237]sdcard 0 line count 4
      [239][mmc]: mmc driver ver 2021-05-21 14:47
      [248][mmc]: Wrong media type 0x0
      [251][mmc]: ***Try SD card 0***
      [276][mmc]: HSSDR52/SDR25 4 bit
      [279][mmc]: 50000000 Hz
      [281][mmc]: 3781 MB
      [283][mmc]: ***SD/MMC 0 init OK!!!***
      [369]Loading boot-pkg Succeed(index=0).
      [373]Entry_name        = u-boot
      [379]Entry_name        = optee
      [383]Entry_name        = dtb
      [386]mmc not para
      [388]Jump to second Boot.
      M/TC: OP-TEE version: 6aef7bb2-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Fri Jul 23 09:25:11 UTC 2021 arm
      
      
      U-Boot 2018.07-ge987def-dirty (Jul 21 2023 - 11:08:46 +0800) Allwinner Technology
      
      [00.440]CPU:   Allwinner Family
      [00.443]Model: sun8iw20
      I2C:   FDT ERROR:fdt_set_all_pin:[twi0]-->FDT_ERR_BADPATH
      FDT ERROR:fdt_set_all_pin:[twi1]-->FDT_ERR_BADPATH
      ready
      [00.464]optee version: major:3 minor:7
      [00.468]DRAM:  128 MiB
      [00.471]Relocation Offset is: 04ecb000
      [00.495]secure enable bit: 0
      [00.498]smc_tee_inform_fdt failed with: ffff000a
      [00.503]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
      [00.509]gic: sec monitor mode
      sunxi flash map init
      [00.514]flash init start
      [00.516]workmode = 17,storage type = 1
      try card 2
      set card number 2
      get card number 2
      [00.524][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00
      [00.531][mmc]: Is not Boot mode!
      [00.533][mmc]: SUNXI SDMMC Controller Version:0x50310
      [00.545][mmc]: ************Try SD card 2************
      [00.550][mmc]: mmc 2 cmd timeout 100 status 100
      [00.554][mmc]: smc 2 err, cmd 8,  RTO
      [00.557][mmc]: mmc 2 close bus gating and reset
      [00.562][mmc]: mmc 2 cmd timeout 100 status 100
      [00.566][mmc]: smc 2 err, cmd 55,  RTO
      [00.570][mmc]: mmc 2 close bus gating and reset
      [00.574][mmc]: ************Try MMC card 2************
      [00.583][mmc]: mmc 2 cmd timeout 100 status 100
      [00.587][mmc]: smc 2 err, cmd 1,  RTO
      [00.591][mmc]: mmc 2 close bus gating and reset
      [00.595][mmc]: Card did not respond to voltage select!
      [00.600][mmc]: ************SD/MMC 2 init error!************
      [00.605][mmc]: mmc init product failed
      MMC init failed
      try emmc fail
      [00.612]sunxi-spinand: AW SPINand MTD Layer Version: 1.8 20220106
      [00.617]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.11 20211217
      [00.625]sunxi-spinand-phy: request spi0 gpio ok
      [00.629]sunxi-spinand-phy: request general tx dma channel ok!
      [00.635]sunxi-spinand-phy: request general rx dma channel ok!
      [00.640]sunxi-spinand-phy: set spic0 clk to 20 Mhz
      [00.645]sunxi-spinand-phy: init spic0 clk ok
      [00.649]sunxi-spinand-phy: detect munufacture from id table: Winbond
      [00.655]sunxi-spinand-phy: detect spinand id: ff21aaef ffffffff
      [00.660]sunxi-spinand-phy: ========== arch info ==========
      [00.666]sunxi-spinand-phy: Model:               W25N01GVZEIG
      [00.671]sunxi-spinand-phy: Munufacture:         Winbond
      [00.676]sunxi-spinand-phy: DieCntPerChip:       1
      [00.680]sunxi-spinand-phy: BlkCntPerDie:        1024
      [00.685]sunxi-spinand-phy: PageCntPerBlk:       64
      [00.690]sunxi-spinand-phy: SectCntPerPage:      4
      [00.694]sunxi-spinand-phy: OobSizePerPage:      64
      [00.698]sunxi-spinand-phy: BadBlockFlag:        0x0
      [00.703]sunxi-spinand-phy: OperationOpt:        0x7
      [00.708]sunxi-spinand-phy: MaxEraseTimes:       65000
      [00.712]sunxi-spinand-phy: EccFlag:             0x0
      [00.717]sunxi-spinand-phy: EccType:             2
      [00.721]sunxi-spinand-phy: EccProtectedType:    3
      [00.726]sunxi-spinand-phy: ========================================
      [00.732]sunxi-spinand-phy: 
      [00.734]sunxi-spinand-phy: ========== physical info ==========
      [00.740]sunxi-spinand-phy: TotalSize:    128 M
      [00.744]sunxi-spinand-phy: SectorSize:   512 B
      [00.748]sunxi-spinand-phy: PageSize:     2 K
      [00.752]sunxi-spinand-phy: BlockSize:    128 K
      [00.756]sunxi-spinand-phy: OOBSize:      64 B
      [00.760]sunxi-spinand-phy: ========================================
      [00.766]sunxi-spinand-phy: 
      [00.769]sunxi-spinand-phy: ========== logical info ==========
      [00.774]sunxi-spinand-phy: TotalSize:    128 M
      [00.779]sunxi-spinand-phy: SectorSize:   512 B
      [00.783]sunxi-spinand-phy: PageSize:     4 K
      [00.787]sunxi-spinand-phy: BlockSize:    256 K
      [00.791]sunxi-spinand-phy: OOBSize:      128 B
      [00.795]sunxi-spinand-phy: ========================================
      [00.801]sunxi-spinand-phy: set spic0 clk to 100 Mhz
      [00.806]sunxi-spinand-phy: block lock register: 0x00
      [00.810]sunxi-spinand-phy: feature register: 0x19
      [00.815]sunxi-spinand-phy: sunxi physic nand init end
      [00.820][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00
      [00.825][mmc]: get sdc_type fail and use default host:tm1.
      [00.831][mmc]: can't find node "mmc0",will add new node
      [00.836][mmc]: fdt err returned <no error>
      [00.840][mmc]: Using default timing para
      [00.843][mmc]: SUNXI SDMMC Controller Version:0x50310
      [00.875][mmc]: card_caps:0x3000000a
      [00.879][mmc]: host_caps:0x3000003f
      [00.884]line:703 init_clocks
      [00.887]init_clocks:finish
      [00.889]drv_disp_init
      [00.896]get flash lcd idx 0
      fdt get node offset faill: hdmi
      ****************** drv_disp_init
      *****************  lcd_init
      [00.908]drv_disp_init finish
      [00.911]boot_gui_init:start
      [00.914]set disp.dev2_output_type fail. using defval=0
      [00.919]disp 0, clk: pll(372000000),clk(372000000),dclk(31000000) dsi_rate(150000000)
           clk real:pll(372000000),clk(372000000),dclk(93000000) dsi_rate(150000000)
      [00.954]switch device: sel=0, type=1, mode=4, format=0, bits=0, eotf=4, cs=260
      [00.961]set disp.fb0_rot_used fail. using defval=0
      [01.128]set disp.fb0_rot_degree fail. using defval=0
      [01.134]boot_gui_init:finish
      [01.136]Loading Environment from SUNXI_FLASH... OK
      [01.141]try to burn key
      [01.143]out of usb burn from boot: not need burn key
      Hit any key to stop autoboot:  0 
      sunxi work mode=0x11
      run card sprite
      [01.155]try sprite_led_gpio config
      [01.158]sprite_led_gpio start
      [01.161]sunxi sprite begin
      firmware name <NULL>
      img start = 0x93b0
      try to read mmc start 37808
      read mmc ok
      sunxi sprite error: iamge magic is bad
      sunxi sprite firmware probe fail
      sprite_test - do a sprite test
      
      Usage:
      sprite_test N[01.187]pwm device hdl is NULL
      [01.190]LCD open finish
      ULL
      =>
      
      发布在 其它全志芯片讨论区
      W
      wjp2547532