@whycanservice 感谢，已解决

在设备树中配置
lcd0的时序后，进入linux 用dump调试发现 lcd时序部分寄存器没有变化
disp_al.c 的disp_al_lcd_cfg函数也没有被调用

@whycan 明白了，谢谢

现在手里的LCD 屏幕要么支持sync 模式 ， 要么支持de模式。这个sync + de
mode 是什么时序啊？

T113-S3 HV interface 怎么设置成sync模式呢？

也只有这个设置？哪个地方可以设置成sync模式

修改./device/config/chips/t113/configs/mq_r/board.dts
设备树如下

sdc2的status 设置为 disabled

再查看生成的....../Tina-Linux/out/t113-mq_r/image/.sunxi.dts
设备树如下

sdc2 的status 设置为 disabled

启动设备后，通过串口终端发现

sdc2 的status 变成了okay

sdc1 和 sdc0 修改status，是可以的
怎么会这样呢？

@whycanservice 感谢回复，昨晚问题已经解决了。板子uart0-rx虚焊问题。放大镜看起来连接了，实际虚焊

背景：自制了一个t113的板子，下载了芒果派的img镜像文件。或者下载基于芒果派修改后，编译生成的img镜像。
问题：在进入busybox后，串口0终端无法输入，板子没得任何回复。插拔usb0，发现有显示usb0的插拔调试信息，说明板子没有死机。现在应该怎么找问题阿？或者大概哪个地方有问题？
芒果派镜像启动，串口信息如下：

[21:57:48.776]收←◆[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.61 (mango@vbox) (arm-openwrt-linux-muslgnueabi-gcc.bin (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) 6.4.1, GNU ld (GNU Binutils) 2.27) #32 SMP PREEMPT Wed Aug 10 15:39:32 UTC 2022
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: sun8iw20
[    0.000000] printk: bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 4 MiB at 0x47c00000
[    0.000000] On node 0 totalpages: 32768
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 15 pages/cpu s30348 r8192 d22900 u61440
[    0.000000] pcpu-alloc: s30348 r8192 d22900 u61440 alloc=15*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 rootdelay=2 loglevel=8 root=/dev/mmcblk0p5 init=/pseudo_init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:private@mmcblk0p6:rootfs_data@mmcblk0p7:UDISK@mmcblk0p8 cma=4M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun8iw20p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.05-g2a1965a(07/10/2022-02:50:57) mbr_offset=1032192 disp_reserve=1536000,0x43f06000 androidboot.dramsize=128 
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 106084K/131072K available (6144K kernel code, 279K rwdata, 1468K rodata, 1024K init, 1161K bss, 20892K reserved, 4096K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] 	Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x26c/0x3ec with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.008025] Switching to timer-based delay loop, resolution 41ns
[    0.014198] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.023887] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.034234] pid_max: default: 32768 minimum: 301
[    0.038976] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.046299] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.054625] CPU: Testing write buffer coherency: ok
[    0.059830] /cpus/cpu@0 missing clock-frequency property
[    0.065155] /cpus/cpu@1 missing clock-frequency property
[    0.070485] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.076644] Setting up static identity map for 0x40100000 - 0x40100060
[    0.083308] rcu: Hierarchical SRCU implementation.
[    0.088538] smp: Bringing up secondary CPUs ...
[    0.094165] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.094285] smp: Brought up 1 node, 2 CPUs
[    0.104115] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[    0.110311] CPU: All CPU(s) started in SVC mode.
[    0.115375] devtmpfs: initialized
[    0.129509] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.137651] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.147744] pinctrl core: initialized pinctrl subsystem
[    0.153873] NET: Registered protocol family 16
[    0.159774] DMA: preallocated 256 KiB pool for atomic coherent allocations

[21:57:49.264]收←◆[    0.195363] rtc_ccu: sunxi ccu init OK
[    0.201432] ccu: sunxi ccu init OK
[    0.205250] r_ccu: sunxi ccu init OK
[    0.227835] iommu: Default domain type: Translated 
[    0.232907] sunxi iommu: irq = 24
[    0.237081] SCSI subsystem initialized
[    0.241011] usbcore: registered new interface driver usbfs
[    0.246531] usbcore: registered new interface driver hub
[    0.251956] usbcore: registered new device driver usb
[    0.257746] Advanced Linux Sound Architecture Driver Initialized.
[    0.264410] Bluetooth: Core ver 2.22
[    0.268022] NET: Registered protocol family 31
[    0.272459] Bluetooth: HCI device and connection manager initialized
[    0.278854] Bluetooth: HCI socket layer initialized
[    0.283737] Bluetooth: L2CAP socket layer initialized
[    0.288832] Bluetooth: SCO socket layer initialized
[    0.293926] pwm module init!
[    0.298002] g2d 5410000.g2d: Adding to iommu group 0
[    0.303299] G2D: rcq version initialized.major:252
[    0.308922] clocksource: Switched to clocksource arch_sys_counter
[    0.323492] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver
[    0.332713] NET: Registered protocol family 2
[    0.337618] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.346056] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.353764] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.360833] TCP: Hash tables configured (established 1024 bind 1024)
[    0.367275] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.373848] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.381049] NET: Registered protocol family 1
[    0.386367] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator
[    0.396664] spi spi0: spi0 supply spi not found, using dummy regulator
[    0.403431] sunxi_spi_resource_get()2116 - [spi0] SPI MASTER MODE
[    0.409582] sunxi_spi_resource_get()2154 - Failed to get sample mode
[    0.415936] sunxi_spi_resource_get()2159 - Failed to get sample delay
[    0.422409] sunxi_spi_resource_get()2163 - sample_mode:-1431633921 sample_delay:-1431633921
[    0.430837] sunxi_spi_clk_init()2205 - [spi0] mclk 100000000
[    0.437105] sunxi_spi_probe()2623 - [spi0]: driver probe succeed, base c881f000, irq 39
[    0.446694] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.457275] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.463299] ntfs: driver 2.1.32 [Flags: R/W].

[21:57:49.565]收←◆[    0.496397] io scheduler mq-deadline registered
[    0.500953] io scheduler kyber registered
[    0.505995] [DISP]disp_module_init
[    0.509939] disp 5000000.disp: Adding to iommu group 0
[    0.515579] [DISP] parser_disp_init_para,line:1430:
[    0.515582] of_property_read fb0_width fail
[    0.524700] [DISP] disp_init,line:2386:
[    0.524705] smooth display screen:0 type:1 mode:4
[    0.549345] display_fb_request,fb_id:0
[    0.555452] Freeing logo buffer memory: 1500K
[    0.560338] disp_al_manager_apply ouput_type:1
[    0.565000] sunxi_pwm_enable_dual: can't parse pwm device
[    0.569221] [DISP]disp_module_init finish
[    0.575452] sunxi_sid_init()551 - insmod ok
[    0.580688] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator
[    0.590866] uart uart0: uart0 supply uart not found, using dummy regulator
[    0.598028] uart0: ttyS0 at MMIO 0x2500000 (irq = 34, base_baud = 1500000) is a SUNXI
[    0.605918] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n
[    0.613915] printk: console [ttyS0] enabled
[    0.613915] printk: console [ttyS0] enabled
[    0.622760] printk: bootconsole [earlycon0] disabled
[    0.622760] printk: bootconsole [earlycon0] disabled
[    0.634087] misc dump reg init
[    0.638581] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator
[    0.649769] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9
[    0.656954] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed
[    0.664267] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed
[    0.671658] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1)
[    0.678150] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power.
[    0.685068] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1)
[    0.692759] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1
[    0.700565] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1
[    0.708613] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled
[    0.716200] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power.
[    0.722924] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1)
[    0.730419] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=207 assert=0
[    0.738338] [ADDR_MGT] addr_mgt_probe: module version: v1.0.11
[    0.745472] [ADDR_MGT] addr_mgt_probe: success.
[    0.750905] dma-buf: Running sanitycheck
[    0.755270] dma-buf: Running dma_fence
[    0.759462] sizeof(dma_fence)=48
[    0.763164] dma-buf: Running dma_fence/sanitycheck
[    0.768517] dma-buf: Running dma_fence/test_signaling
[    0.774182] dma-buf: Running dma_fence/test_add_callback
[    0.780109] dma-buf: Running dma_fence/test_late_add_callback
[    0.786509] dma-buf: Running dma_fence/test_rm_callback
[    0.792335] dma-buf: Running dma_fence/test_late_rm_callback
[    0.798641] dma-buf: Running dma_fence/test_status
[    0.803984] dma-buf: Running dma_fence/test_error
[    0.809229] dma-buf: Running dma_fence/test_wait
[    0.814369] dma-buf: Running dma_fence/test_wait_timeout

[21:57:49.927]收←◆[    0.858936] dma-buf: Running dma_fence/test_stub
[    0.864090] dma-buf: Running dma_fence/race_signal_callback

[21:57:50.007]收←◆[    0.938932] thread_signal_callback[0] completed 37842 passes, 14151 misses
[    0.946634] thread_signal_callback[1] completed 37824 passes, 14134 misses

[21:57:50.087]收←◆[    1.018941] thread_signal_callback[0] completed 40565 passes, 40565 misses
[    1.026633] thread_signal_callback[1] completed 40540 passes, 40540 misses
[    1.034823] sunxi-spinand: AW SPINand MTD Layer Version: 2.3 20211223
[    1.042083] sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.10 20200306
[    1.053200] random: fast init done

[21:57:50.388]收←◆[    1.319295] random: crng init done

[21:57:51.117]收←◆[    2.049000] sunxi-spinand-phy: read id failed : -110
[    2.054546] spi-nand: probe of spi0.0 failed with error -110
[    2.060996] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.068265] sunxi-ehci: EHCI SUNXI driver
[    2.073191] get ehci1-controller wakeup-source is fail.
[    2.079131] sunxi ehci1-controller don't init wakeup source
[    2.085338] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xc0b61480, 0x:c8837000, irq_no:3a
[    2.097278] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply drvvbus not found, using dummy regulator
[    2.109664] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator
[    2.121779] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller
[    2.129006] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1
[    2.138876] sunxi-ehci 4200000.ehci1-controller: irq 58, io mem 0x04200000
[    2.168955] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00
[    2.177550] hub 1-0:1.0: USB hub found
[    2.181785] hub 1-0:1.0: 1 port detected
[    2.186717] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.193651] sunxi-ohci: OHCI SUNXI driver
[    2.198569] get ohci1-controller wakeup-source is fail.
[    2.204515] sunxi ohci1-controller don't init wakeup source
[    2.210737] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xc0b61710
[    2.220358] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply drvvbus not found, using dummy regulator
[    2.232777] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator
[    2.244867] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller
[    2.252093] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2
[    2.261922] sunxi-ohci 4200400.ohci1-controller: irq 59, io mem 0x04200400

[21:57:51.412]收←◆[    2.343742] hub 2-0:1.0: USB hub found
[    2.347950] hub 2-0:1.0: 1 port detected
[    2.353015] i2c /dev entries driver
[    2.356974] sunxi cedar version 1.1
[    2.361070] sunxi-cedar 1c0e000.ve: Adding to iommu group 0
[    2.367337] VE: sunxi_cedar_probe power-domain init!!!
[    2.373078] VE: install start!!!
[    2.373078] 
[    2.378564] VE: cedar-ve the get irq is 40
[    2.378564] 
[    2.384985] VE: ve_debug_proc_info:be331635, data:537944a6, lock:fc475bca
[    2.384985] 
[    2.394202] VE: install end!!!
[    2.394202] 
[    2.399251] VE: sunxi_cedar_probe
[    2.403192] Bluetooth: HCI UART driver ver 2.3
[    2.408137] Bluetooth: HCI UART protocol H4 registered
[    2.413873] Bluetooth: HCI UART protocol BCSP registered
[    2.419798] Bluetooth: HCI UART protocol (null) registered
[    2.425898] Bluetooth: HCI Realtek H5 protocol initialized
[    2.433947] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.22 2021-12-20 15:40)
[    2.443909] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8
[    2.450094] sunxi-mmc 4020000.sdmmc: No vmmc regulator found
[    2.456391] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found
[    2.462813] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found
[    2.469221] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found
[    2.475717] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found
[    2.482220] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found
[    2.488708] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found
[    2.495659] sunxi-mmc 4020000.sdmmc: Got CD GPIO
[    2.501013] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail
[    2.507584] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.518682] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator
[    2.538790] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.563157] sunxi-mmc 4020000.sdmmc: detmode:gpio irq
[    2.568805] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.580825] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.22 2021-12-20 15:40)
[    2.583382] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.590727] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8
[    2.604422] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.608251] sunxi-mmc 4021000.sdmmc: No vmmc regulator found
[    2.622759] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.626069] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found
[    2.644014] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found
[    2.650435] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found
[    2.656927] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found
[    2.659269] mmc0: host does not support reading read-only switch, assuming write-enable
[    2.663433] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found
[    2.674045] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    2.678853] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found
[    2.678899] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed
[    2.690396] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    2.717299] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[    2.729063] mmc0: new high speed SDHC card at address 0001
[    2.735742] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.747424] mmcblk0: mmc0:0001  15.0 GiB 
[    2.751994] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[    2.754877] Alternate GPT is invalid, using primary GPT.
[    2.765579]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
[    2.772142] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.796321] sunxi-mmc 4021000.sdmmc: detmode:manually by software
[    2.803860] exFAT: Version 1.3.0
[    2.803962] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    2.815086] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    2.816264] sunxi-spdif 2036000.spdif: Not using gpio-spdif gpio from dts
[    2.829530] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.839553] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator
[    2.852938] [AUDIOCODEC][sunxi_codec_parse_params][2412]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1
[    2.852938] 
[    2.853335] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.870072] [AUDIOCODEC][sunxi_codec_parse_params][2448]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0
[    2.892482] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    2.899197] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    2.905904] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    2.912610] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    2.912637] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    2.919755] [AUDIOCODEC][sunxi_internal_codec_probe][2609]:codec probe finished
[    2.939531] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present!
[    2.949305] [SNDCODEC][sunxi_card_init][583]:card init finished
[    2.956362] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok
[    2.967207] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input0
[    2.979097] [SNDCODEC][sunxi_card_dev_probe][836]:register card finished
[    2.987448] NET: Registered protocol family 10
[    2.993377] Segment Routing with IPv6
[    2.997530] NET: Registered protocol family 17
[    3.002558] [SNDCODEC][sunxi_hs_init_work][259]:resume-->report switch
[    3.009107] Bluetooth: RFCOMM TTY layer initialized
[    3.015263] Bluetooth: RFCOMM socket layer initialized
[    3.021029] Bluetooth: RFCOMM ver 1.11
[    3.025756] Registering SWP/SWPB emulation handler
[    3.045429] sunxi-i2c sunxi-i2c2: sunxi-i2c2 supply twi not found, using dummy regulator
[    3.055303] sunxi-i2c sunxi-i2c2: probe success
[    3.062705] debugfs: Directory '2031000.dmic' with parent 'snddmic' already present!
[    3.071923] sunxi-audio-card 2031060.sounddmic: dmic-hifi <-> 2031000.dmic mapping ok
[    3.081536] sunxi-audio-card 203605c.soundspdif: use dummy codec for simple card.
[    3.090048] debugfs: Directory '2036000.spdif' with parent 'sndspdif' already present!
[    3.099385] sunxi-audio-card 203605c.soundspdif: snd-soc-dummy-dai <-> 2036000.spdif mapping ok
[    3.110001] get ehci0-controller wakeup-source is fail.
[    3.115914] sunxi ehci0-controller don't init wakeup source
[    3.122163] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xc0b60f60, 0x:c88a6000, irq_no:38
[    3.134079] [sunxi-ehci0]: Not init ehci0
[    3.138854] get ohci0-controller wakeup-source is fail.
[    3.144797] sunxi ohci0-controller don't init wakeup source
[    3.151023] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xc0b611f0
[    3.160626] [sunxi-ohci0]: Not init ohci0
[    3.168142] clk: Not disabling unused clocks
[    3.173093] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    3.182721] cfg80211: failed to load regulatory.db
[    3.182745] ALSA device list:
[    3.191408]   #0: audiocodec
[    3.194610]   #1: snddmic
[    3.197522]   #2: sndspdif
[    3.200562] alloc_fd: slot 0 not NULL!
[    3.204946] Waiting 2 sec before mounting root device...

[21:57:54.311]收←◆[    5.242204] VFS: Mounted root (squashfs filesystem) readonly on device 179:5.
[    5.252956] devtmpfs: mounted
[    5.258153] Freeing unused kernel memory: 1024K
[    5.269071] Run /pseudo_init as init process

[21:57:54.439]收←◆mount: mounting none on /dev failed: Resource busy

[21:57:54.486]收←◆mount: mounting /dev/by-name/rootfs_data on /overlay failed: No such device
Mount Failed: formating /dev/by-name/rootfs_data to ext4 ...
/pseudo_init: line 402: mkfs.ext4: not found
can't run '/etc/preinit': No such file or directory
mount: mounting proc on /proc failed: Resource busy
mount: mounting tmpfs on /run failed: No such file or directory
hostname: can't open '/etc/hostname': No such file or directory
------run rc.preboot file-----
install private mount info
libubi: error!: "/dev/by-name/private" is not a character device
ubiblock: error!: error while probing "/dev/by-name/private"
[    5.486931] /dev/ubiblock0_: Can't open blockdev
          error 22 (Invalid argument)
mount: mounting /dev/ubiblock0_ on /tmp/private/ failed: No such file or directory
/etc/init.d/rcS: line 136: mkfs.ext4: not found
------run rc.modules file-----
[    5.537071] usbcore: registered new interface driver usb-storage
[    5.547727] sunxi_gpadc_init,2151, success
[    5.552680] sunxi_gpadc_setup: get channel scan data failed
[    5.559298] input: sunxi-gpadc0 as /devices/virtual/input/input1
[    5.570953] get ctp_power is fail, -22
[    5.575163] get ctp_power_ldo_vol is fail, -22
[    5.581247] sunxi_ctp_startup: ctp_power_io is invalid.
[    5.587136] get ctp_gesture_wakeup fail, no gesture wakeup
[    5.593292] gt9xxnew_ts 2-0014: 2-0014 supply ctp not found, using dummy regulator

[21:57:54.834]收←◆[    5.765912] sunxi-i2c sunxi-i2c2: Bus error
[    5.770645] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    5.778203] sunxi-i2c sunxi-i2c2: STOP failed!
[    5.783177] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    5.797884] sunxi-i2c sunxi-i2c2: Bus error
[    5.802615] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    5.810170] sunxi-i2c sunxi-i2c2: STOP failed!
[    5.815144] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    5.829580] sunxi-i2c sunxi-i2c2: Bus error
[    5.834315] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    5.841865] sunxi-i2c sunxi-i2c2: STOP failed!
[    5.846838] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    5.861560] sunxi-i2c sunxi-i2c2: Bus error
[    5.866293] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    5.873842] sunxi-i2c sunxi-i2c2: STOP failed!
[    5.878817] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    5.893353] sunxi-i2c sunxi-i2c2: Bus error
[    5.898085] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    5.905634] sunxi-i2c sunxi-i2c2: STOP failed!
[    5.910633] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    5.918198] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -22! Process reset.

[21:57:55.147]收←◆[    6.078930] <<-GTP-ERROR->> GTP i2c test failed time 1.

[21:57:55.184]收←◆[    6.116026] sunxi-i2c sunxi-i2c2: Bus error
[    6.120756] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    6.128311] sunxi-i2c sunxi-i2c2: STOP failed!
[    6.133283] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    6.147792] sunxi-i2c sunxi-i2c2: Bus error
[    6.152521] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    6.160076] sunxi-i2c sunxi-i2c2: STOP failed!
[    6.165067] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    6.179793] sunxi-i2c sunxi-i2c2: Bus error
[    6.184522] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    6.192081] sunxi-i2c sunxi-i2c2: STOP failed!
[    6.197055] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    6.211505] sunxi-i2c sunxi-i2c2: Bus error
[    6.216243] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    6.223794] sunxi-i2c sunxi-i2c2: STOP failed!
[    6.228767] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    6.243380] sunxi-i2c sunxi-i2c2: Bus error
[    6.248110] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    6.255670] sunxi-i2c sunxi-i2c2: STOP failed!
[    6.260662] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    6.268218] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -22! Process reset.

[21:57:55.497]收←◆[    6.428932] <<-GTP-ERROR->> GTP i2c test failed time 2.

[21:57:55.534]收←◆[    6.465884] sunxi-i2c sunxi-i2c2: Bus error
[    6.470618] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    6.478172] sunxi-i2c sunxi-i2c2: STOP failed!
[    6.483143] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    6.497870] sunxi-i2c sunxi-i2c2: Bus error
[    6.502599] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    6.510157] sunxi-i2c sunxi-i2c2: STOP failed!
[    6.515150] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    6.529541] sunxi-i2c sunxi-i2c2: Bus error
[    6.534276] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    6.541828] sunxi-i2c sunxi-i2c2: STOP failed!
[    6.546801] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    6.561454] sunxi-i2c sunxi-i2c2: Bus error
[    6.566184] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    6.573742] sunxi-i2c sunxi-i2c2: STOP failed!
[    6.578714] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    6.593193] sunxi-i2c sunxi-i2c2: Bus error
[    6.597920] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    6.605477] sunxi-i2c sunxi-i2c2: STOP failed!
[    6.610466] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    6.618022] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -22! Process reset.

[21:57:55.788]收←◆[    6.719190] sunxi_usb_udc 4100000.udc-controller: 4100000.udc-controller supply udc not found, using dummy regulator

[21:57:55.847]收←◆[    6.778940] <<-GTP-ERROR->> GTP i2c test failed time 3.
[    6.816029] sunxi-i2c sunxi-i2c2: Bus error
[    6.820763] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    6.828314] sunxi-i2c sunxi-i2c2: STOP failed!
[    6.833292] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    6.847683] sunxi-i2c sunxi-i2c2: Bus error
[    6.852415] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    6.859972] sunxi-i2c sunxi-i2c2: STOP failed!
[    6.864968] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    6.879588] sunxi-i2c sunxi-i2c2: Bus error
[    6.884322] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    6.891873] sunxi-i2c sunxi-i2c2: STOP failed!
[    6.896850] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    6.911227] sunxi-i2c sunxi-i2c2: Bus error
[    6.915964] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    6.923516] sunxi-i2c sunxi-i2c2: STOP failed!
[    6.928492] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    6.943002] sunxi-i2c sunxi-i2c2: Bus error
[    6.947735] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    6.955287] sunxi-i2c sunxi-i2c2: STOP failed!
[    6.960282] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    6.967852] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -22! Process reset.

[21:57:56.197]收←◆[    7.128930] <<-GTP-ERROR->> GTP i2c test failed time 4.

[21:57:56.234]收←◆[    7.165821] sunxi-i2c sunxi-i2c2: Bus error
[    7.170553] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    7.178110] sunxi-i2c sunxi-i2c2: STOP failed!
[    7.183082] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    7.197712] sunxi-i2c sunxi-i2c2: Bus error
[    7.202448] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    7.210001] sunxi-i2c sunxi-i2c2: STOP failed!
[    7.214994] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    7.229308] sunxi-i2c sunxi-i2c2: Bus error
[    7.234032] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    7.241594] sunxi-i2c sunxi-i2c2: STOP failed!
[    7.246569] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    7.261133] sunxi-i2c sunxi-i2c2: Bus error
[    7.265864] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    7.273426] sunxi-i2c sunxi-i2c2: STOP failed!
[    7.278397] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    7.292810] sunxi-i2c sunxi-i2c2: Bus error
[    7.297542] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle
[    7.305101] sunxi-i2c sunxi-i2c2: STOP failed!
[    7.310090] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14)
[    7.317658] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -22! Process reset.

[21:57:56.547]收←◆[    7.478929] <<-GTP-ERROR->> GTP i2c test failed time 5.

[21:57:56.577]收←◆[    7.508930] I2C communication ERROR!
[    7.508957] regulator-dummy: Underflow of regulator enable count
[    7.519816] gt9xxnew_ts: probe of 2-0014 failed with error -1

[21:57:56.670]收←◆[    7.601780] Error: Driver 'gt9xxnew_ts' is already registered, aborting...

[21:57:56.768]收←◆insmod: can't insert '/lib/modules/5.4.61/gt9xxnew_ts.ko': Operation not permitted

[21:57:56.914]收←◆[    7.844480] RTW: module init start
[    7.848273] RTW: rtl8189fs v5.11.3-29-g5a946024c.20200901
[    7.854322] RTW: build time: Aug 10 2022 14:48:36
[    7.869595] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success

[21:57:57.046]收←◆[    7.976676] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
[    7.982887] RTW: ----- platform_wifi_power_on sdc_id: 1
[    7.988758] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.999858] RTW: rtw_inetaddr_notifier_register
[    8.004951] RTW: module init ret=0
[    8.009065] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[    8.028954] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    8.053935] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    8.061545] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    8.068347] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    8.083955] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    8.097645] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    8.105152] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    8.112662] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    8.120177] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    8.126881] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B

[21:58:01.183]收←◆Successfully initialized wpa_supplicant
Could not read interface wlan0 flags: No such device
nl80211: Driver does not support authentication/association or connect commands
nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Could not read interface wlan0 flags: No such device
wlan0: Failed to initialize driver interface
------run rc.final file-----

[21:58:01.306]收←◆[   12.237183] file system registered
[   12.253824] configfs-gadget 4100000.udc-controller: failed to start g1: -19
sh: write error: No such device
[   12.275064] read descriptors
[   12.278305] read strings

[21:58:02.308]收←◆[   13.239125] [ehci0-controller]: sunxi_usb_enable_ehci
[   13.244771] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xc0b60f60, 0x:c88a6000, irq_no:38
[   13.256784] android_work: did not send uevent (0 0 00000000)
[   13.263336] sunxi-ehci 4101000.ehci0-controller: 4101000.ehci0-controller supply hci not found, using dummy regulator
[   13.276722] sunxi-ehci 4101000.ehci0-controller: EHCI Host Controller
[   13.283968] sunxi-ehci 4101000.ehci0-controller: new USB bus registered, assigned bus number 3
[   13.294041] sunxi-ehci 4101000.ehci0-controller: irq 56, io mem 0x04101000
[   13.328948] sunxi-ehci 4101000.ehci0-controller: USB 2.0 started, EHCI 1.00
[   13.337522] hub 3-0:1.0: USB hub found
[   13.341799] hub 3-0:1.0: 1 port detected
[   13.346653] [ohci0-controller]: sunxi_usb_enable_ohci
[   13.352312] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xc0b611f0
[   13.362142] sunxi-ohci 4101400.ohci0-controller: 4101400.ohci0-controller supply hci not found, using dummy regulator
[   13.374371] sunxi-ohci 4101400.ohci0-controller: OHCI Host Controller
[   13.381631] sunxi-ohci 4101400.ohci0-controller: new USB bus registered, assigned bus number 4
[   13.391386] debugfs: Directory 'sunxi-ohci' with parent 'ohci' already present!
[   13.399620] sunxi-ohci 4101400.ohci0-controller: irq 57, io mem 0x04101400

[21:58:02.543]收←◆[   13.473724] hub 4-0:1.0: USB hub found
[   13.477945] hub 4-0:1.0: 1 port detected
host_chose finished!
clear private mount info
nice: can't execute '/usr/bin/story_ota_bin': No such file or directory
umount: can't unmount /tmp/private/: Invalid argument
libubi: error!: "/dev/by-name/private" is not a character device
ubiblock: error!: error while probing "/dev/by-name/private"
          error 22 (Invalid argument)


BusyBox v1.27.2 () built-in shell (ash)

------run profile file-----
 _____  _              __     _
|_   _||_| ___  _ _   |  |   |_| ___  _ _  _ _
  | |   _ |   ||   |  |  |__ | ||   || | ||_'_|
  | |  | || | || _ |  |_____||_||_|_||___||_,_|
  |_|  |_||_|_||_|_|  Tina is Based on OpenWrt!
 ----------------------------------------------
 Tina Linux (Neptune, 5C1C9C53)
 ----------------------------------------------
nodev	debugfs
root@TinaLinux:/# 


发送命令后的反应：
------run profile file-----
 _____  _              __     _
|_   _||_| ___  _ _   |  |   |_| ___  _ _  _ _
  | |   _ |   ||   |  |  |__ | ||   || | ||_'_|
  | |  | || | || _ |  |_____||_||_|_||___||_,_|
  |_|  |_||_|_||_|_|  Tina is Based on OpenWrt!
 ----------------------------------------------
 Tina Linux (Neptune, 5C1C9C53)
 ----------------------------------------------
nodev	debugfs
root@TinaLinux:/# 
[21:58:05.385]发→◇ls





□
[21:58:06.095]发→◇ls





□
[21:58:21.308]发→◇ls





□
[21:58:21.770]发→◇ls