@zcxhappy
最终我通过以下步骤wifi终于跑起来了。。。
1）insmod xr829.ko
root@TinaLinux:/# insmod xr829.ko
======== XRADIO WIFI OPEN ========
[XRADIO_ERR] debugfs isnot initialized
[XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31
[XRADIO] Allocated hw_priv @ (____ptrval____)
sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[XRADIO] Detect SDIO card 1
sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
mmc1: new high speed SDIO card at address 0001
[SBUS] XRadio Device:sdio clk=50000000
[XRADIO] XRADIO_HW_REV 1.0 detected.
[XRADIO] xradio_update_dpllctrl: DPLL_CTRL Sync=0x00c00000.
[XRADIO] Bootloader complete
[XRADIO] Firmware completed.
[WSM] Firmware Label:XR_C09.08.52.73_DBG_02.122 2GHZ HT40 May 18 2021 13:36:09
[XRADIO] Firmware Startup Done.
[XRADIO_WRN] enable Multi-Rx!
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
2）ifconfig wlan0 up
3）/etc/init.d/wpa_supplicant start
4）wifi_connect_ap_test xxx xxx
5) ping baidu.com
root@TinaLinux:~# ping baidu.com
PING baidu.com (39.156.66.10): 56 data bytes
64 bytes from 39.156.66.10: seq=0 ttl=52 time=46.361 ms
64 bytes from 39.156.66.10: seq=1 ttl=52 time=96.778 ms
64 bytes from 39.156.66.10: seq=2 ttl=52 time=52.996 ms
64 bytes from 39.156.66.10: seq=3 ttl=52 time=53.184 ms
64 bytes from 39.156.66.10: seq=4 ttl=52 time=55.643 ms
中途以为硬件问题，重新打板了，做了些修改SDC2换成SDC1