全志T3怎样配置LVDS接口液晶屏

[xubaoguo002]

使用的是主线代码，内核版本5.18，设备树用的sun8i-r40-bananapi-m2-ultra.dts，不清楚该怎样配置。求教一下哪位大佬配置过LVDS相关的设备树参数。对下面这部分内容很少迷糊啊

	tcon_top: tcon-top@1c70000 {
		compatible = "allwinner,sun8i-r40-tcon-top";
		reg = <0x01c70000 0x1000>;
		clocks = <&ccu CLK_BUS_TCON_TOP>,
			 <&ccu CLK_TCON_TV0>,
			 <&ccu CLK_TVE0>,
			 <&ccu CLK_TCON_TV1>,
			 <&ccu CLK_TVE1>,
			 <&ccu CLK_DSI_DPHY>;
		clock-names = "bus",
			      "tcon-tv0",
			      "tve0",
			      "tcon-tv1",
			      "tve1",
			      "dsi";
		clock-output-names = "tcon-top-tv0",
				     "tcon-top-tv1",
				     "tcon-top-dsi";
		resets = <&ccu RST_BUS_TCON_TOP>;
		#clock-cells = <1>;

		ports {
			#address-cells = <1>;
			#size-cells = <0>;

			tcon_top_mixer0_in: port@0 {
				reg = <0>;

				tcon_top_mixer0_in_mixer0: endpoint {
					remote-endpoint = <&mixer0_out_tcon_top>;
				};
			};

			tcon_top_mixer0_out: port@1 {
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <1>;

				tcon_top_mixer0_out_tcon_lcd0: endpoint@0 {
					reg = <0>;
				};

				tcon_top_mixer0_out_tcon_lcd1: endpoint@1 {
					reg = <1>;
				};

				tcon_top_mixer0_out_tcon_tv0: endpoint@2 {
					reg = <2>;
					remote-endpoint = <&tcon_tv0_in_tcon_top_mixer0>;
				};

				tcon_top_mixer0_out_tcon_tv1: endpoint@3 {
					reg = <3>;
					remote-endpoint = <&tcon_tv1_in_tcon_top_mixer0>;
				};
			};

			tcon_top_mixer1_in: port@2 {
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <2>;

				tcon_top_mixer1_in_mixer1: endpoint@1 {
					reg = <1>;
					remote-endpoint = <&mixer1_out_tcon_top>;
				};
			};

			tcon_top_mixer1_out: port@3 {
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <3>;

				tcon_top_mixer1_out_tcon_lcd0: endpoint@0 {
					reg = <0>;
				};

				tcon_top_mixer1_out_tcon_lcd1: endpoint@1 {
					reg = <1>;
				};

				tcon_top_mixer1_out_tcon_tv0: endpoint@2 {
					reg = <2>;
					remote-endpoint = <&tcon_tv0_in_tcon_top_mixer1>;
				};

				tcon_top_mixer1_out_tcon_tv1: endpoint@3 {
					reg = <3>;
					remote-endpoint = <&tcon_tv1_in_tcon_top_mixer1>;
				};
			};

			tcon_top_hdmi_in: port@4 {
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <4>;

				tcon_top_hdmi_in_tcon_tv0: endpoint@0 {
					reg = <0>;
					remote-endpoint = <&tcon_tv0_out_tcon_top>;
				};

				tcon_top_hdmi_in_tcon_tv1: endpoint@1 {
					reg = <1>;
					remote-endpoint = <&tcon_tv1_out_tcon_top>;
				};
			};

			tcon_top_hdmi_out: port@5 {
				reg = <5>;

				tcon_top_hdmi_out_hdmi: endpoint {
					remote-endpoint = <&hdmi_in_tcon_top>;
				};
			};
		};
	};

	tcon_tv0: lcd-controller@1c73000 {
		compatible = "allwinner,sun8i-r40-tcon-tv";
		reg = <0x01c73000 0x1000>;
		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&ccu CLK_BUS_TCON_TV0>, <&tcon_top CLK_TCON_TOP_TV0>;
		clock-names = "ahb", "tcon-ch0";
		resets = <&ccu RST_BUS_TCON_TV0>, <&ccu RST_BUS_LVDS>;
		reset-names = "lcd", "lvds";
		clock-output-names = "tcon0-pixel-clock";
		status = "disabled";

		ports {
			#address-cells = <1>;
			#size-cells = <0>;

			tcon_tv0_in: port@0 {
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <0>;

				tcon_tv0_in_tcon_top_mixer0: endpoint@0 {
					reg = <0>;
					remote-endpoint = <&tcon_top_mixer0_out_tcon_tv0>;
				};

				tcon_tv0_in_tcon_top_mixer1: endpoint@1 {
					reg = <1>;
					remote-endpoint = <&tcon_top_mixer1_out_tcon_tv0>;
				};
			};

			tcon_tv0_out: port@1 {
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <1>;

				tcon_tv0_out_tcon_top: endpoint@1 {
					reg = <1>;
					remote-endpoint = <&tcon_top_hdmi_in_tcon_tv0>;
				};
			};
		};
	};

[uuuuid]

建议用官方tina SDK

[WhycanService]

主线使用的是drm驱动，建议参考kernel的doc

https://www.kernel.org/doc/html/latest/