D1s调试rtp，触控屏，电阻屏出现open consoledevice: No such file or directory

[lingeasy]

在调试D1s的RTP屏幕时，使用getevent可以看到相关的event，手按在上面大概要1秒以上才会出现数据，而且更新的也比较慢。
在使用TSLIB_TSDEVICE=/dev/input/event0 ts_test，提示“open consoledevice: No such file or directory”和“KDSETMODE: Bad file descriptor”，求大神提点一下，问题出现在哪里了。

root@TinaLinux:/# getevent
add device 1: /dev/input/event2
  name:     "sunxi-gpadc0"
add device 2: /dev/input/event1
  name:     "audiocodec sunxi Audio Jack"
add device 3: /dev/input/event0
  name:     "2009c00.rtp"
poll 4, returned 1
/dev/input/event0: 0003 0000 00000511
poll 4, returned 1
/dev/input/event0: 0003 0001 00000837
poll 4, returned 1
/dev/input/event0: 0001 014a 00000001
poll 4, returned 1
/dev/input/event0: 0000 0000 00000000
poll 4, returned 1
/dev/input/event0: 0003 0000 00000523
poll 4, returned 1
/dev/input/event0: 0000 0000 00000000
poll 4, returned 1
/dev/input/event0: 0003 0000 00000512
poll 4, returned 1
/dev/input/event0: 0003 0001 00000838
poll 4, returned 1
/dev/input/event0: 0000 0000 00000000
poll 4, returned 1
/dev/input/event0: 0001 014a 00000000
poll 4, returned 1
/dev/input/event0: 0000 0000 00000000
poll 4, returned 1
/dev/input/event0: 0003 0000 000009c9
poll 4, returned 1
/dev/input/event0: 0003 0001 0000091c
poll 4, returned 1
/dev/input/event0: 0001 014a 00000001
poll 4, returned 1
/dev/input/event0: 0000 0000 00000000
poll 4, returned 1
/dev/input/event0: 0001 014a 00000000
poll 4, returned 1
/dev/input/event0: 0000 0000 00000000
^Z[2]+  Stopped                    getevent
root@TinaLinux:/#

root@TinaLinux:/# TSLIB_TSDEVICE=/dev/input/event0 ts_test
open consoledevice: No such file or directory
KDSETMODE: Bad file descriptor

[whycan]

@lingeasy
cat /proc/interrupts

看下中断的增加速度

[lingeasy]

@whycan

root@TinaLinux:/# cat /proc/interrupts
           CPU0
  2:         10  SiFive PLIC  78  sun4i-ts
  4:          0  SiFive PLIC  80  2010000.iommu
  6:          0  SiFive PLIC  82  cedar_dev
  8:          0  SiFive PLIC 160  7090000.rtc
 21:        134  SiFive PLIC  21  uart3
 29:          0  SiFive PLIC 105  5410000.g2d
 30:      57816  SiFive PLIC 106  dispaly
 31:      17714  SiFive PLIC  31  spi0
 36:          6  SiFive PLIC  36  ledcirq
 41:          0  SiFive PLIC  41  audio jack irq
 45:        103  SiFive PLIC  45  sunxi_usb_udc
 49:          0  SiFive PLIC  49  ehci_hcd:usb1
 50:          0  SiFive PLIC  50  ohci_hcd:usb2
 56:          0  SiFive PLIC  56  mmc0
 62:          0  SiFive PLIC  62  4500000.eth
 66:       4117  SiFive PLIC  66  3002000.dma-controller
 73:          0  SiFive PLIC  73  sunxi-gpadc
 75:          0  SiFive PLIC  75  timer@2050000
177:          1  sunxi_pio_edge 134  4020000.sdmmc cd

看了一下，如上。

[lingeasy]

@whycan 这个错误提示是哪里出问题了

root@TinaLinux:/# TSLIB_TSDEVICE=/dev/input/event0 ts_test
open consoledevice: No such file or directory
KDSETMODE: Bad file descriptor

[whycan]

@lingeasy

TSLIB_FBDEVICE=/dev/fb0 TSLIB_TSDEVICE=/dev/input/event0 ts_calibrate

参考这个： Linux 执行 ts_test ts_calibrate 都提示 No such file or directory, 求教

[lingeasy]

@whycan 还是相同的提示，是不是配置哪里少了？

root@TinaLinux:/# TSLIB_FBDEVICE=/dev/fb0 TSLIB_TSDEVICE=/dev/input/event0 ts_calibrate
open consoledevice: No such file or directory
KDSETMODE: Bad file descriptor

[whycan]

@lingeasy

https://blog.csdn.net/qq_21792169/article/details/50408577

TSLIB_CONSOLEDEVICE=/dev/tty1 TSLIB_FBDEVICE=/dev/fb0 TSLIB_TSDEVICE=/dev/input/event0 ts_calibrate

[lingeasy]

@whycan 增加完成以后又提示“Couldnt load module input” 和“No raw modules loaded”。

root@TinaLinux:/# export TSLIB_TSDEVICE=/dev/event0
root@TinaLinux:/# export TSLIB_CALIBFILE=/etc/pointercal
root@TinaLinux:/# export TSLIB_CONFFILE=/etc/ts.conf
root@TinaLinux:/# export TSLIB_PLUGINDIR=/lib/ts/
root@TinaLinux:/# export TSLIB_CONSOLEDEVICE=/dev/ttyS3
root@TinaLinux:/# export TSLIB_FBDEVICE=/dev/fb0

root@TinaLinux:/# TSLIB_CONSOLEDEVICE=/dev/ttyS3 TSLIB_FBDEVICE=/dev/fb0 TSLIB_T
SDEVICE=/dev/input/event0 ts_calibrate
Couldnt load module input
No raw modules loaded.
ts_config: Success
ts_setup: Success

ts.conf内容如下：

# Uncomment if you wish to use the one-wire linux input layer S70/A70...
# module_raw one_wire_ts_input

# Uncomment if you wish to use the linux input layer event interface
module_raw input

# Uncomment if you're using a Sharp Zaurus SL-5500/SL-5000d
# module_raw collie

# Uncomment if you're using a Sharp Zaurus SL-C700/C750/C760/C860
# module_raw corgi

# Uncomment if you're using a device with a UCB1200/1300/1400 TS interface
# module_raw ucb1x00

# Uncomment if you're using an HP iPaq h3600 or similar
# module_raw h3600

# Uncomment if you're using a Hitachi Webpad
# module_raw mk712

# Uncomment if you're using an IBM Arctic II
# module_raw arctic2

module pthres pmin=1
module variance delta=30
module dejitter delta=100
module linear

[whycan]

@lingeasy 在 D1s调试rtp，触控屏，电阻屏出现open consoledevice: No such file or directory 中说：

ts.conf

这个文件完整路径是什么呢？

[lingeasy]

@whycan 是路径不对 改了一下“SLIB_PLUGINDIR=/usr/lib/ts”，目前是正常了，配置如下：

#! /bin/sh

export TSLIB_CALIBFILE=/etc/pointercal
export TSLIB_CONFFILE=/etc/ts.conf
export TSLIB_PLUGINDIR=/usr/lib/ts
export TSLIB_CONSOLEDEVICE=none
export TSLIB_FBDEVICE=/dev/fb0
export TSLIB_TSDEVICE=/dev/input/event0

[lingeasy]

@whycan 使用ts_test的时候，非常不跟手，需要配置哪些呀 大神指点

[whycan]

@lingeasy
芯片自带的RTP吗？

[lingeasy]

@whycan 用的是d1s哪吒开发板上的rtp功能。

[lingeasy]

@whycan 已经解决了，看到在别一个帖子里面的说明
修改“lichee/linux-5.4/drivers/input/touchscreen/sun4i-ts.c”文件中相关内容
【原内容】

	writel(ADC_CLK_SEL(0) | ADC_CLK_DIV(2) | FS_DIV(7) | T_ACQ(63),
	       ts->base + TP_CTRL0);
	if (of_device_is_compatible(np, "allwinner,sun8i-ts"))
		writel(ADC_FIRST_DLY(0x1) | ADC_FIRST_DLY_MODE(0x1)
			| ADC_CLK_DIV(0x2) | FS_DIV(2) | T_ACQ(5),
			ts->base + TP_CTRL0);

【修改后】

	writel(ADC_CLK_SEL(0) | ADC_CLK_DIV(2) | FS_DIV(7) | T_ACQ(63),
	       ts->base + TP_CTRL0);
	if (of_device_is_compatible(np, "allwinner,sun8i-ts"))
		writel(ADC_FIRST_DLY(0xf) | ADC_FIRST_DLY_MODE(0x1)
			| ADC_CLK_DIV(0x2) | FS_DIV(6) | T_ACQ(63),
			ts->base + TP_CTRL0);

[whycan]

@lingeasy
谢谢分享！