T113-S3烧录SD卡不能启动；提示；未找到MMC设备2 mmc 2找不到，所以不退出

[Liu0597666]

这是什么原因，我自己做的开发板，跪求各位大神，求解，

[whycan]

@liu0597666

请用文字贴出全部日志记录。

[chloe159753]

@whycan [186]HELLO! BOOT0 is starting!
[189]BOOT0 commit : 27369ab
[192]set pll start
[194]periph0 has been enabled
[197]set pll end
[198][pmu]: bus read error
[201]board init ok
[203]ZQ value = 0x30***********
[206]get_pmu_exist() = -1
[208]ddr_efuse_type: 0xa
[211][AUTO DEBUG] single rank and full DQ!
[215]ddr_efuse_type: 0xa
[218][AUTO DEBUG] rank 0 row = 13
[221][AUTO DEBUG] rank 0 bank = 4
[224][AUTO DEBUG] rank 0 page size = 2 KB
[228]DRAM BOOT DRIVE INFO: V0.24
[231]DRAM CLK = 528 MHz
[233]DRAM Type = 2 (2:DDR2,3:DDR3)
[237]DRAMC read ODT off.
[239]DRAM ODT off.
[241]ddr_efuse_type: 0xa
[244]DRAM SIZE =64 M
[247]DRAM simple test OK.
[250]dram size =64
[251]card no is 0
[253]sdcard 0 line count 4
[256][mmc]: mmc driver ver 2021-04-2 16:45
[265][mmc]: Wrong media type 0x0
[268][mmc]: Try SD card 0
[297][mmc]: HSSDR52/SDR25 4 bit
[299][mmc]: 50000000 Hz
[302][mmc]: 7580 MB
[304][mmc]: SD/MMC 0 init OK!!!
[369]Loading boot-pkg Succeed(index=0).
[372]Entry_name = opensbi
[375]Entry_name = u-boot
[379]Entry_name = dtb
[382]mmc not para
[383]Jump to second Boot.

OpenSBI v0.6

---

/ __ \ / | _ _ |
| | | | __ ___ _ __ | ( | |) || |
| | | | '_ \ / _ \ '_ \ ___ | _ < | |
| || | |) | __/ | | |) | |) || |
_/| ./ _|| ||/|____/|
| |
|_|

Platform Name : T-HEAD Xuantie Platform
Platform HART Features : RV64ACDFIMSUVX
Platform Max HARTs : 1
Current Hart : 0
Firmware Base : 0x40000400
Firmware Size : 75 KB
Runtime SBI Version : 0.2

MIDELEG : 0x0000000000000222
MEDELEG : 0x000000000000b1ff
PMP0 : 0x0000000040000000-0x000000004001ffff (A)
PMP1 : 0x0000000040000000-0x000000007fffffff (A,R,W,X)
PMP2 : 0x0000000000000000-0x0000000007ffffff (A,R,W)
PMP3 : 0x0000000009000000-0x000000000901ffff (▒

U-Boot 2018.05-g0a88ac9 (Apr 30 2021 - 11:23:28 +0000) Allwinner Technology

[00.466]DRAM: 64 MiB
[00.468]Relocation Offset is: 01ef0000
[00.472]secure enable bit: 0
[00.475]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz
[00.481]flash init start
[00.483]workmode = 0,storage type = 1
[00.487][mmc]: mmc driver ver uboot2018:2021-04-16 14:23:00-1
[00.493][mmc]: get sdc_type fail and use default host:tm1.
[00.499][mmc]: can't find node "mmc0",will add new node
[00.504][mmc]: fdt err returned <no error>
[00.507][mmc]: Using default timing para
[00.511][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.548][mmc]: card_caps:0x3000000a
[00.551][mmc]: host_caps:0x3000003f
[00.557]sunxi flash init ok
[00.560]line:714 init_clocks
__clk_init: clk pll_periph0x2 already initialized
register fix_factor clk error
[00.570]drv_disp_init
fdt_getprop_u32 s_pwm.pwm-base fail
[00.586]drv_disp_init finish
[00.588]boot_gui_init:start
[00.591]set disp.dev2_output_type fail. using defval=0
[00.597]boot_gui_init:finish
partno erro : can't find partition bootloader
54 bytes read in 1 ms (52.7 KiB/s)
[00.624]bmp_name=bootlogo.bmp size 1152054
1152054 bytes read in 50 ms (22 MiB/s)
[00.699]Loading Environment from SUNXI_FLASH... OK
[00.723]out of usb burn from boot: not need burn key
root_partition is rootfs
set root to /dev/mmcblk0p5
[00.734]update part info
[00.737]update bootcmd
[00.740]change working_fdt 0x42aafda8 to 0x42a8fda8
[00.761]update dts
Hit any key to stop autoboot: 0
[00.777]LCD open finish
Android's image name: d1-mangopi_mq_rg
No reserved memory region found in source FDT
[01.191]
Starting kernel ...

[01.194][mmc]: MMC Device 2 not found
[01.197][mmc]: mmc 2 not find, so not exit

遇到这个同样问题d1s上，怎么解决呀？