F133-A 烧录新的镜像后重启打印 no vendor_boot partition is found

[jianwei]

烧录镜像后重启无法进入系统

重启打印如下

[53]HELLO! BOOT0 is starting!
[56]BOOT0 commit : 977af20-dirty
[59]set pll start
[61]periph0 has been enabled
[64]set pll end
[65][pmu]: bus read error
[67]board init ok
[69]ZQ value = 0x31
[71]get_pmu_exist() = -1
[73]DRAM BOOT DRIVE INFO: V0.33
[76]DRAM CLK = 528 MHz
[78]DRAM Type = 2 (2:DDR2,3:DDR3)
[81]DRAMC read ODT  off.
[84]DRAM ODT off.
[86]ddr_efuse_type: 0xa
[88]DRAM SIZE =64 M
[90]dram_tpr4:0x0
[92]PLL_DDR_CTRL_REG:0xf8002b00
[95]DRAM_CLK_REG:0xc0000000
[97][TIMING DEBUG] MR2= 0x0
[102]DRAM simple test OK.
[104]dram size =64
[106]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32
[111]block from 8 to 32
[167]Check is correct.
[169]dma 0x30338 int is not used yet
[173]dma 0x30338 int is free, you do not need to free it again
[179]Entry_name        = opensbi
[182]Entry_name        = u-boot
[186]Entry_name        = dtb
[188]Jump to second Boot.

OpenSBI auto-t113-linux-V0.8-1-g771d82e
   ____                    _____ ____ _____
  / __ \                  / ____|  _ \_   _|
 | |  | |_ __   ___ _ __ | (___ | |_) || |
 | |  | | '_ \ / _ \ '_ \ \___ \|  _ < | |
 | |__| | |_) |  __/ | | |____) | |_) || |_
  \____/| .__/ \___|_| |_|_____/|____/_____|
        | |
        |_|

Platform Name          : T-HEAD Xuantie Platform
Platform HART Features : RV64ACDFIMSUVX
Platform Max HARTs     : 1
Current Hart           : 0
Firmware Base          : 0x41fc0400
Firmware Size          : 75 KB
Runtime SBI Version    : 0.2

MIDELEG : 0x0000000000000222
MEDELEG : 0x000000000000b1ff
PMP0    : 0x0000000041fc0000-0x0000000041fdffff (A)
PMP1    : 0x0000000040000000-0x000000007fffffff (A,R,W,X)
PMP2    : 0x0000000080000000-0x00000000bfffffff (A,R,W,X)
PMP3    : 0x0000000000020000-0x0000000000027fff (A,

U-Boot 2018.05-00006-g294b3a0-config-dirty (Feb 09 2022 - 17:06:36 +0800) Allwinner Technology

[00.275]DRAM:  64 MiB
[00.277]Relocation Offset is: 01ede000
[00.282]secure enable bit: 0
[00.284]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
[00.291]flash init start
[00.293]workmode = 0,storage type = 0

device nand0 <nand>, # parts = 4
 #: name                size            offset          mask_flags
 0: boot0               0x00100000      0x00000000      1
 1: uboot               0x00300000      0x00100000      1
 2: secure_storage      0x00100000      0x00400000      1
 3: sys                 0x0fb00000      0x00500000      0

active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000

defaults:
mtdids  : nand0=nand
mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
[00.469]ubi0: attaching mtd4
[00.657]ubi0: scanning is finished
[00.664]ubi0: attached mtd4 (name "sys", size 251 MiB)
[00.669]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[00.675]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[00.681]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[00.688]ubi0: good PEBs: 1004, bad PEBs: 0, corrupted PEBs: 0
[00.693]ubi0: user volume: 10, internal volumes: 1, max. volumes count: 128
[00.700]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
[00.708]ubi0: available PEBs: 0, total reserved PEBs: 1004, PEBs reserved for bad PEB handling: 40
[00.716]sunxi flash init ok
[00.719]line:703 init_clocks
[00.722]drv_disp_init
request pwm success, pwm7:pwm7:0x2000c00.
fdt get node offset faill: hdmi
[00.740]unable to map hdmi registers
[00.743]drv_disp_init finish
[00.848]Loading Environment from SUNXI_FLASH... OK
[00.868]boot_gui_init:start
[00.871]set disp.dev2_output_type fail. using defval=0
[00.878]boot_gui_init:finish
partno erro : can't find partition bootloader
54 bytes read in 1 ms (52.7 KiB/s)
[00.898]bmp_name=bootlogo.bmp size 38454
38454 bytes read in 3 ms (12.2 MiB/s)
[00.909]out of usb burn from boot: not need burn key
[00.915]Item0 (Map) magic is bad
List file under ULI/factory
** Unrecognized filesystem type **
[00.934]update bootcmd
[00.946]change working_fdt 0x42a9dda0 to 0x42a7dda0
No reserved memory region found in source FDT
[00.975]update dts
noncached_alloc(): addr = 0x42b11e00
noncached_alloc(): addr = 0x42b11e40
noncached_alloc(): addr = 0x42b11e80
noncached_alloc(): addr = 0x42b126c0
geth_sys_init:634: get node 'gmac0' error
geth_sys_init fail!
[00.995]Board Net Initialization Failed
[00.998]No ethernet found.
Hit any key to stop autoboot:  1 FDT ERROR:get muxsel err returned FDT_ERR_INTERNAL
sunxi_pwm_pin_set_state, fdt_set_all_pin, ret=-1
[01.069]LCD open finish
 0 
[02.303]no vendor_boot partition is found
Android's image name: f133-evb1
Detect comp none
[02.319]
Starting kernel ...

有没有前辈能指点一下是什么情况导致的
而且想要再次进行烧录的时候检测不到USB设备了