D1 SD卡启动失败，概率100%

YiXinTai LV 5

log如下：

[69]HELLO! BOOT0 is starting!
[72]BOOT0 commit : 88480af
[75]set pll start
[76]fix vccio detect value:0xc0
[79]periph0 has been enabled
[82]set pll end
[84][pmu]: bus read error
[86]board init ok
[88]get_pmu_exist() = -1
[90]ddr_efuse_type: 0x0
[93]trefi:7.8ms
[95][AUTO DEBUG] single rank and full DQ!
[99]ddr_efuse_type: 0x0
[101]trefi:7.8ms
[104][AUTO DEBUG] rank 0 row = 15 
[107][AUTO DEBUG] rank 0 bank = 8 
[110][AUTO DEBUG] rank 0 page size = 2 KB 
[114]DRAM BOOT DRIVE INFO: V0.33
[117]DRAM CLK = 480 MHz
[119]DRAM Type = 3 (2:DDR2,3:DDR3)
[122]DRAMC ZQ value: 0x7b7bfb
[125]DRAM ODT value: 0x42.
[128]ddr_efuse_type: 0x0
[131]DRAM SIZE =512 M
[133]dram_tpr4:0x0
[134]PLL_DDR_CTRL_REG:0xf8002700
[137]DRAM_CLK_REG:0xc0000000
[140][TIMING DEBUG] MR2= 0x18
[145]DRAM simple test OK.
[147]dram size =512
[149]card no is 0
[151]sdcard 0 line count 4
[153][mmc]: mmc driver ver 2021-04-2 16:45
[163][mmc]: Wrong media type 0x0
[165][mmc]: ***Try SD card 0***
[175][mmc]: HSSDR52/SDR25 4 bit
[178][mmc]: 50000000 Hz
[181][mmc]: 14916 MB
[182][mmc]: ***SD/MMC 0 init OK!!!***
[233]Loading boot-pkg Succeed(index=0).
[236]Entry_name        = opensbi
[239]Entry_name        = u-boot
[243]Entry_name        = dtb
[246]mmc not para
[247]Jump to second Boot.

OpenSBI auto-t113-linux-V0.8-3-ge39e937
   ____                    _____ ____ _____
  / __ \                  / ____|  _ \_   _|
 | |  | |_ __   ___ _ __ | (___ | |_) || |
 | |  | | '_ \ / _ \ '_ \ \___ \|  _ < | |
 | |__| | |_) |  __/ | | |____) | |_) || |_
  \____/| .__/ \___|_| |_|_____/|____/_____|
        | |
        |_|

Platform Name          : T-HEAD Xuantie Platform
Platform HART Features : RV64ACDFIMSUVX
Platform Max HARTs     : 1
Current Hart           : 0
Firmware Base          : 0x41fc0400
Firmware Size          : 75 KB
Runtime SBI Version    : 0.2

MIDELEG : 0x0000000000000222
MEDELEG : 0x000000000000b1ff
PMP0    : 0x0000000041fc0000-0x0000000041fdffff (A)
PMP1    : 0x0000000040000000-0x000000007fffffff (A,R,W,X)
PMP2    : 0x0000000080000000-0x00000000bfffffff (A,R,W,X)
PMP3    : 0x0000000000020000-0x0000000000027fff (A,[00.328][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00
[00.334][mmc]: get sdc_type fail and use default host:tm1.
[00.340][mmc]: can't find node "mmc0",will add new node
[00.345][mmc]: fdt err returned <no error>
[00.349][mmc]: Using default timing para
[00.352][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.370][mmc]: card_caps:0x30000002
[00.373][mmc]: host_caps:0x3000003f
[00.427]set disp.dev2_output_type fail. using defval=0
[00.453]set disp.fb0_rot_used fail. using defval=0
[00.458]set disp.fb0_rot_degree fail. using defval=0
[00.642]out of usb burn from boot: not need burn key
[00.647]Item0 (Map) magic is bad
[00.650]the secure storage item0 copy0 magic is bad
[00.656]Item0 (Map) magic is bad
[00.658]the secure storage item0 copy1 magic is bad
[00.663]Item0 (Map) magic is bad
[00.674]The storage not support sample function
[00.749]dts_get_dsp_memory: no /reserved-memory/dsp0 in fdt
[00.754]dts_get_dsp_memory fail
[01.099]no vendor_boot partition is found
[01.311]
Starting kernel ...

[01.314][mmc]: MMC Device 2 not found
[01.317][mmc]: mmc 2 not find, so not exit
[    0.210646] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed
[    0.218056] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed
[    0.294604] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    0.302321] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    0.314643] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    0.322283] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    0.329918] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    0.337553] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    0.382203] sunxi-i2c sunxi-i2c2: Address + Read bit transmitted, ACK not received
[    0.390657] sunxi-i2c sunxi-i2c2: engine mode: I2C BUS error state is 0x48
[    0.398485] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x38)
[    0.416829] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    0.426055] CPU: 0 PID: 1 Comm: swapper Not tainted 5.4.61 #1
[    0.432454] Call Trace:
[    0.435198] [<ffffffe00002a3ee>] walk_stackframe+0x0/0xa0
[    0.441216] [<ffffffe00002a5d0>] show_stack+0x2a/0x34
[    0.446850] [<ffffffe0004f52a8>] dump_stack+0x20/0x28
[    0.452482] [<ffffffe00002f396>] panic+0xee/0x2b6
[    0.457727] [<ffffffe000000ed6>] mount_block_root+0x1ee/0x28a
[    0.464131] [<ffffffe000000ff8>] mount_root+0x86/0x90
[    0.469761] [<ffffffe000001112>] prepare_namespace+0x110/0x152
[    0.476263] [<ffffffe000000b74>] kernel_init_freeable+0x17e/0x19a
[    0.483060] [<ffffffe000508bb6>] kernel_init+0x12/0xee
[    0.488788] [<ffffffe000029038>] ret_from_exception+0x0/0xc
[    0.495007] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---

whycan晕哥 LV 9

@yixintai 在 D1 SD卡启动失败，概率100% 中说：

[ 0.294604] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 0.302321] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 0.314643] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 0.322283] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 0.329918] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 0.337553] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!

这张卡烧官方固件正常吗？

YiXinTai LV 5

@whycan 卡是正常的，使用其他固件都可以。也换过很多卡，都遇到这种问题。都是使用PhonenixCrad制作启动卡

whycan晕哥 LV 9

@yixintai
那SDK你改过什么呢？

YiXinTai LV 5

@whycan 默认编译，什么都不改d1-h-nezha_min

whycan晕哥 LV 9

@yixintai
那先换张卡吧

YiXinTai LV 5

@whycan 上面说过，换过很多卡了，跟卡无关。

whycan晕哥 LV 9

@yixintai
那麻烦把 img 固件传上来，我烧一个看看。

YiXinTai LV 5

@whycan tina_d1-h-nezha_min_uart0-ddr480.img

whycan晕哥 LV 9

@yixintai 在 D1 SD卡启动失败，概率100% 中说：

@whycan tina_d1-h-nezha_min_uart0-ddr480.img

[87]HELLO! BOOT0 is starting!
[90]BOOT0 commit : 88480af
[92]set pll start
[94]fix vccio detect value:0xc0
[97]periph0 has been enabled
[100]set pll end
[101][pmu]: bus read error
[104]board init ok
[106]get_pmu_exist() = -1
[108]ddr_efuse_type: 0x0
[111]trefi:7.8ms
[113][AUTO DEBUG] two rank and full DQ!
[117]ddr_efuse_type: 0x0
[119]trefi:7.8ms
[122][AUTO DEBUG] rank 0 row = 15
[125][AUTO DEBUG] rank 0 bank = 8
[128][AUTO DEBUG] rank 0 page size = 2 KB
[132][AUTO DEBUG] rank 1 row = 15
[135][AUTO DEBUG] rank 1 bank = 8
[138][AUTO DEBUG] rank 1 page size = 2 KB
[142]rank1 config same as rank0
[145]DRAM BOOT DRIVE INFO: V0.33
[148]DRAM CLK = 480 MHz
[150]DRAM Type = 3 (2:DDR2,3:DDR3)
[153]DRAMC ZQ value: 0x7b7bfb
[156]DRAM ODT value: 0x42.
[159]ddr_efuse_type: 0x0
[162]DRAM SIZE =1024 M
[164]dram_tpr4:0x0
[166]PLL_DDR_CTRL_REG:0xf8002700
[169]DRAM_CLK_REG:0xc0000000
[171][TIMING DEBUG] MR2= 0x18
[176]DRAM simple test OK.
[179]dram size =1024
[181]card no is 0
[182]sdcard 0 line count 4
[185][mmc]: mmc driver ver 2021-04-2 16:45
[194][mmc]: Wrong media type 0x0
[197][mmc]: ***Try SD card 0***
[210][mmc]: HSSDR52/SDR25 4 bit
[212][mmc]: 50000000 Hz
[215][mmc]: 1876 MB
[217][mmc]: ***SD/MMC 0 init OK!!!***
[276]Loading boot-pkg Succeed(index=0).
[279]Entry_name        = opensbi
[282]Entry_name        = u-boot
[286]Entry_name        = dtb
[289]mmc not para
[290]Jump to second Boot.

OpenSBI auto-t113-linux-V0.8-3-ge39e937
   ____                    _____ ____ _____
  / __ \                  / ____|  _ \_   _|
 | |  | |_ __   ___ _ __ | (___ | |_) || |
 | |  | | '_ \ / _ \ '_ \ \___ \|  _ < | |
 | |__| | |_) |  __/ | | |____) | |_) || |_
  \____/| .__/ \___|_| |_|_____/|____/_____|
        | |
        |_|

Platform Name          : T-HEAD Xuantie Platform
Platform HART Features : RV64ACDFIMSUVX
Platform Max HARTs     : 1
Current Hart           : 0
Firmware Base          : 0x41fc0400
Firmware Size          : 75 KB
Runtime SBI Version    : 0.2

MIDELEG : 0x0000000000000222
MEDELEG : 0x000000000000b1ff
PMP0    : 0x0000000041fc0000-0x0000000041fdffff (A)
PMP1    : 0x0000000040000000-0x000000007fffffff (A,R,W,X)
PMP2    : 0x0000000080000000-0x00000000bfffffff (A,R,W,X)
PMP3    : 0x0000000000020000-0x0000000000027fff (A,▒[00.371][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00
[00.377][mmc]: get sdc_type fail and use default host:tm1.
[00.383][mmc]: can't find node "mmc0",will add new node
[00.388][mmc]: fdt err returned <no error>
[00.392][mmc]: Using default timing para
[00.395][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.416][mmc]: card_caps:0x3000000a
[00.419][mmc]: host_caps:0x3000003f
[00.464]set disp.dev2_output_type fail. using defval=0
[00.491]set disp.fb0_rot_used fail. using defval=0
[00.495]set disp.fb0_rot_degree fail. using defval=0
[00.685]out of usb burn from boot: not need burn key
[00.695]Item0 (Map) magic is bad
[00.698]the secure storage item0 copy0 magic is bad
[00.708]Item0 (Map) magic is bad
[00.711]the secure storage item0 copy1 magic is bad
[00.716]Item0 (Map) magic is bad
[01.563]The storage not support sample function
[01.620]dts_get_dsp_memory: no /reserved-memory/dsp0 in fdt
[01.625]dts_get_dsp_memory fail
[01.830]no vendor_boot partition is found
[02.043]
Starting kernel ...

[02.046][mmc]: MMC Device 2 not found
[02.049][mmc]: mmc 2 not find, so not exit
[    0.212672] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed
[    0.220084] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed
[    0.301259] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    0.309005] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    0.321264] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    0.328932] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    0.336517] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    0.344171] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
formating /dev/by-name/UDISK to ext4
/etc/preinit: line 1: mkfs.ext4: not found
[    7.286489] block: extroot: cannot find device UDISK
Please press Enter to activate this console.
[    9.408310] configfs-gadget 4100000.udc-controller: failed to start g1: -19
[   12.891002] ======== XRADIO WIFI OPEN ========
[   12.897389] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31
[   12.904585] [XRADIO] Allocated hw_priv @ (____ptrval____)
[   13.246950] [XRADIO] Detect SDIO card 1
[   13.283677] [SBUS] XRadio Device:sdio clk=50000000
[   13.291391] [XRADIO] XRADIO_HW_REV 1.0 detected.
[   13.397745] [XRADIO] xradio_update_dpllctrl: DPLL_CTRL Sync=0x00c00000.
[   13.483530] [XRADIO] Bootloader complete
[   13.676308] [XRADIO] Firmware completed.
[   13.682888] [WSM] Firmware Label:XR_C09.08.52.73_DBG_02.122 2GHZ HT40 May 18 2021 13:36:09
[   13.700485] [XRADIO] Firmware Startup Done.
[   13.705712] [XRADIO_WRN] enable Multi-Rx!
kmodloader done
[   14.564957] ieee80211_do_open: vif_type=2, p2p=0, ch=3, addr=8c:3b:fb:a2:39:ce
[   14.600626] [STA] !!!xradio_vif_setup: id=0, type=2, p2p=0, addr=8c:3b:fb:a2:39:ce
[   14.621872] [AP_WRN] BSS_CHANGED_ASSOC but driver is unjoined.



BusyBox v1.27.2 () built-in shell (ash)

 _____  _              __     _
|_   _||_| ___  _ _   |  |   |_| ___  _ _  _ _
  | |   _ |   ||   |  |  |__ | ||   || | ||_'_|
  | |  | || | || _ |  |_____||_||_|_||___||_,_|
  |_|  |_||_|_||_|_|  Tina is Based on OpenWrt!
 ----------------------------------------------
 Tina Linux (Neptune, 61CC0487)
 ----------------------------------------------
root@TinaLinux:/#
root@TinaLinux:/#

我这里一切正常.

lovexulu LV 7

@yixintai 注意烧卡时候选择烧启动卡。你这是烧了量产卡吧

YiXinTai LV 5

@lovexulu 是启动卡，@whycan晕哥谢谢，我检查一下板子