系统有时出现无法启动的情况，提示如下

[lingeasy]

系统启动的时候会出现如下提示，然后系统就停止了。

[53]HELLO! BOOT0 is starting!
[56]BOOT0 commit : 88480af
[59]set pll start
[61]periph0 has been enabled
[64]set pll end
[65][pmu]: bus read error
[67]board init ok
[69]ZQ value = 0x2e
[71]get_pmu_exist() = -1
[73]DRAM BOOT DRIVE INFO: V0.33
[76]DRAM CLK = 528 MHz
[78]DRAM Type = 2 (2:DDR2,3:DDR3)
[81]DRAMC read ODT  off.
[84]DRAM ODT off.
[86]ddr_efuse_type: 0xa
[88]DRAM SIZE =64 M
[90]dram_tpr4:0x0
[92]PLL_DDR_CTRL_REG:0xf8002b00
[95]DRAM_CLK_REG:0xc0000000
[97][TIMING DEBUG] MR2= 0x0
[102]DRAM simple test OK.
[104]dram size =64
[106]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32
[111]block from 8 to 32
[168]Check is correct.
[170]dma 0x301a8 int is not used yet
[174]dma 0x301a8 int is free, you do not need to free it again
[180]Entry_name        = opensbi
[183]Entry_name        = u-boot
[187]Entry_name        = dtb
[189]Jump to second Boot.

OpenSBI auto-t113-linux-V0.8-3-ge39e937
   ____                    _____ ____ _____
  / __ \                  / ____|  _ \_   _|
 | |  | |_ __   ___ _ __ | (___ | |_) || |
 | |  | | '_ \ / _ \ '_ \ \___ \|  _ < | |
 | |__| | |_) |  __/ | | |____) | |_) || |_
  \____/| .__/ \___|_| |_|_____/|____/_____|
        | |
        |_|

Platform Name          : T-HEAD Xuantie Platform
Platform HART Features : RV64ACDFIMSUVX
Platform Max HARTs     : 1
Current Hart           : 0
Firmware Base          : 0x41fc0400
Firmware Size          : 75 KB
Runtime SBI Version    : 0.2

MIDELEG : 0x0000000000000222
MEDELEG : 0x000000000000b1ff
PMP0    : 0x0000000041fc0000-0▒

U-Boot 2018.07-ge987def-dirty (Apr 20 2023 - 11:37:55 +0800) Allwinner Technology

[00.258]DRAM:  64 MiB
[00.260]Relocation Offset is: 01ee9000
[00.265]secure enable bit: 0
can't support chip type 24064
[00.271]CPU=720 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
sunxi flash map init
SPI ALL:   ready
[00.282]flash init start
[00.284]workmode = 0,storage type = 0
[00.292]sunxi-spinand-phy: spinand sample_mode:2 sample_delay:2

device nand0 <nand>, # parts = 4
 #: name                size            offset          mask_flags
 0: boot0               0x00100000      0x00000000      1
 1: uboot               0x00300000      0x00100000      1
 2: secure_storage      0x00100000      0x00400000      1
 3: sys                 0x07b00000      0x00500000      0

active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000

defaults:
mtdids  : nand0=nand
mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
[00.409]ubi0: attaching mtd4
[00.526]ubi0: scanning is finished
[00.533]ubi0: attached mtd4 (name "sys", size 123 MiB)
[00.538]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[00.544]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[00.550]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[00.557]ubi0: good PEBs: 492, bad PEBs: 0, corrupted PEBs: 0
[00.562]ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128
[00.569]ubi0: max/mean erase counter: 4/1, WL threshold: 4096, image sequence number: 0
[00.576]ubi0: available PEBs: 0, total reserved PEBs: 492, PEBs reserved for bad PEB handling: 20
[00.588]sunxi flash init ok
[00.591]line:703 init_clocks
[00.594]drv_disp_init
request pwm success, pwm7:pwm7:0x2000c00.
[00.615]drv_disp_init finish
[00.720]Loading Environment from SUNXI_FLASH... OK
[00.743]boot_gui_init:start
[00.746]set disp.dev2_output_type fail. using defval=0
====LCD_power_on=====!!!!!!![00.755]set disp.fb0_rot_used fail. using defval=0
[00.759]set disp.fb0_rot_degree fail. using defval=0
[00.765]boot_gui_init:finish
partno erro : can't find partition bootloader
[00.783]bmp_name=b====----=====!!!!!!!ootlogo.bmp size 51798
[00.795]out of usb burn from boot: not need burn key
[00.800]Item0 (Map) magic is bad
partno erro : can't find partition private
[00.829]update bootcmd
[00.842]change working_fdt 0x42aa8da0 to 0x42a88da0
No reserved memory region found in source FDT
[00.877]update dts
Hit any key to stop autoboot:  1 ====LCD_bl_open=====!!!!!!!FDT ERROR:get muxsel err returned FDT_ERR_INTERNAL
sunxi_pwm_pin_set_state, fdt_set_all_pin, ret=-1
[00.951]LCD open finish