T113麻雀，TF卡启动，经常卡死

[gonboy]

32G TF卡，启动时，经常卡死在如下代码， 如何解决？

‘’‘bash
[ 5.299707] Run /pseudo_init as init process
mount: mounting none on /dev failed: Resource busy
[ 5.998854] EXT4-fs: Warning: mounting with data=journal disables delayed allocation and O_DIRECT support!
[ 6.020692] EXT4-fs (mmcblk0p7): mounted filesystem with journalled data mode. Opts: data=journal
can't run '/etc/preinit': No such file or directory
mount: mounting proc on /proc failed: Resource busy
mount: mounting tmpfs on /run failed: No such file or directory
hostname: can't open '/etc/hostname': No such file or directory
------run rc.preboot file-----
’‘’

[whycan]

是不是把整个剩余分区都作为ext4根文件系统了？

[gonboy]

@whycan 启动后，查看了,TD卡，剩余的29G大小 分区。 是ext4。
系统主分区不是ext4, 是默认的squashfs

[whycan]

@gonboy
那有没有卡在 ext4 文件系统加载？

[gonboy]

@whycan 1. 没有文件，在ext4分区，进行启动加载。
2. 这种现象，貌似 是对 29G的空间进行，格式化。（偶尔会启动慢）

can't run '/etc/preinit': No such file or directory
mount: mounting proc on /proc failed: Resource busy
mount: mounting tmpfs on /run failed: No such file or directory
hostname: can't open '/etc/hostname': No such file or directory
------run rc.preboot file-----
[    6.412934] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: (null)
------run rc.modules file-----
insmod: can't insert '/lib/modules/5.4.61/usb-storage.ko': No such file or directory
[    6.467474] sunxi_gpadc_init,2151, success
[    6.472441] sunxi_gpadc_setup: get channel scan data failed
[    6.479050] input: sunxi-gpadc0 as /devices/virtual/input/input1
[    6.491148] get ctp_power is fail, -22
[    6.495359] get ctp_power_ldo_vol is fail, -22
[    6.500392] sunxi_ctp_startup: ctp_power_io is invalid.
[    6.506288] get ctp_gesture_wakeup fail, no gesture wakeup
[    6.512475] gt9xxnew_ts 2-0014: 2-0014 supply ctp not found, using dummy regulator
[    6.709604] input: gt9xxnew_ts as /devices/virtual/input/input2
[    6.996971] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
[    7.104136] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
[    7.110433] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.122094] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[    7.142279] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.167200] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.182888] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.196179] sunxi-mmc 4021000.sdmmc: card claims to support voltages below defined range
[    7.214867] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    7.226470] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    7.238313] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[    7.250839] mmc1: new high speed SDIO card at address 0001
Successfully initialized wpa_supplicant
------run rc.final file-----
mount: mounting /dev/mmcblk0p1 on /mnt/extsd failed: No such file or directory