V853 烧入固件之后，系统起不来，出现内核崩溃，ADB也无法使用。
-
v853 烧入固件之后，系统起不来，出现内核崩溃，ADB也无法使用。
串口完整日志如下：
[127]HELLO! SBOOT is starting! [130]sboot commit : 4b419f21ba [134]PMU: AXP21 [137]set pll start [139]periph0 has been enabled [142]set pll end [143]board init ok [145]DRAM use external ZQ!! [148]chip id check OK [150]DRAM_VCC set to 1500 mv [153]DRAM BOOT DRIVE INFO: V0.16 [156]DRAM CLK = 936 MHz [158]DRAM Type = 3 (2:DDR2,3:DDR3) [161]DRAMC ZQ value: 0x7b7bfb [164]DRAM ODT value: 0x42. [168]DRAM SIZE =512 M [170]dram_tpr4:0x0 [173]DRAM simple test OK. [175]rtc standby flag is 0x0, super standby flag is 0x0 [180]dram size =512 [182]audio:avcc calibration [185][mmc]: mmc driver ver 2021-12-27 10:07 [194][mmc]: Wrong media type 0x0, but host sdc2, try mmc first [200][mmc]: ***Try MMC card 2*** [211][mmc]: RMCA OK! [213][mmc]: bias 100 [215][mmc]: mmc 2 bias 100 [222][mmc]: MMC 5.1 [224][mmc]: HSSDR52/SDR25 8 bit [227][mmc]: 50000000 Hz [229][mmc]: 3616 MB [231][mmc]: ***SD/MMC 2 init OK!!!*** [295]read toc1 from emmc 32800 sector [299]OLD version: 0.0 [301]NEW version: 0.0 [304]don't have rotpk, skip check [369]load rotpk hash [431]load boot-key hash [433]load boot hash [565]monitor entry=0x0 [567]uboot entry=0x43000000 [570]optee entry=0x41980000 [573]opensbi entry=0x0 [575]no need rotpk flag [577]tunning data addr:0x430003e8 [580]drm_region_size is 0 [583]run out of boot0 M/TC: OP-TEE version: 15ee1539b (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016 U-Boot 2018.05-ga697d75-dirty (Nov 27 2023 - 22:29:43 +0800) Allwinner Technolog [00.754]CPU: Allwinner Family [00.757]Model: sun8iw21 I2C: ready [00.785]DRAM: 512 MiB [00.788]Relocation Offset is: 1ced0000 [00.813]secure enable bit: 1 E/TC:0 fdt_getprop_u32:343 prop trace_level not found [00.828]PMU: AXP21 [00.830]BMU: AXP21 FDT ERROR:fdt_get_regulator_name:get property handle twi-supply error:FDT_ERR_IN bias_name:pc_bias bias_vol:1800 bias_name:pi_bias bias_vol:1800 [00.854]CPU=900 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=24Mhz MBus=300Mhz [00.860]gic: sec monitor mode sunxi flash map init [00.865]flash init start [00.867]workmode = 0,storage type = 2 [00.870][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00 [00.876][mmc]: get sdc_type fail and use default host:tm4. [00.882][mmc]: SUNXI SDMMC Controller Version:0x50400 [00.907][mmc]: Best spd md: 2-HSDDR52/DDR50, freq: 2-50000000, Bus width: 8 [00.914]sunxi flash init ok [00.929]line:724 init_clocks [00.932]drv_disp_init request pwm success, pwm9:pwm9:0x2000c00. [00.946]drv_disp_init finish [00.952]Loading Environment from SUNXI_FLASH... OK [00.963]boot_gui_init:start [00.966]set disp.dev2_output_type fail. using defval=0 [00.970][ICN6202 TO LVDS] LINE:0146-->lcd_open_flow: [00.975][ICN6202 TO LVDS] LINE:0146-->lcd_open_flow: [00.980][ICN6202 TO LVDS] LINE:0167-->lcd_power_on: [00.998]boot_gui_init:finish [01.000]Item0 (Map) magic is bad [01.003]the secure storage item0 copy0 magic is bad [01.008]Item0 (Map) magic is bad [0[01.011][ICN6202 TO LVDS] LINE:0146-->lcd_open_flow: [01.015][ICN6202 TO LVDS] LINE:0575-->lcd_panel_init: [01.182][ICN6202 TO LVDS] LINE:0620-->lcd_panel_init:initialization:icn6202 init 1.011]the secure storage item0 copy1 magic is bad [01.194]Item0 (Map) magic is bad [01.197]out of usb burn from boot: not need burn key root_partition is rootfs set root to /dev/mmcblk0p4 [01.207]update part info [01.210]update bootcmd [01.212]change working_fdt 0x5de8fe70 to 0x5de6fe70 [01.219][mmc]: delete mmc-hs400-1_8v from dtb [01.223][mmc]: delete mmc-hs200-1_8v from dtb [01.227][mmc]: get max-frequency ok 50000000 Hz disable nand error: FDT_ERR_BADPATH [01.240]The storage not support sample function [01.246]## error: update_fdt_dram_para : FDT_ERR_NOTFOUND [01.255]update dts Hit any key to stop autoboot: 1 [01.310][ICN6202 TO LVDS] LINE:0146-->lcd_open_ [01.320][ICN6202 TO LVDS] LINE:0146-->lcd_open_flow: [01.324][ICN6202 TO LVDS] LINE:0203-->lcd_bl_open: FDT ERROR:fdt_get_all_pin:get property handle pinctrl-0 error:FDT_ERR_INTERNAL sunxi_pwm_pin_set_state, fdt_set_all_pin, ret=-1 [01.340][ICN6202 TO LVDS] LINE:0146-->lcd_open_flow: [01.345][ICN6202 TO LVDS] LINE:0146-->lcd_open_flow: [01.350]LCD open finish pubkey boot valid [02.396]no vendor_boot partition is found Android's image name: v853-vision [02.436]Starting kernel ... [02.439][mmc]: mmc exit start [02.456][mmc]: mmc 2 exit ok [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.191 (allwinner@allwinner-VirtualBox) (gcc versi:36:59 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio [ 0.000000] OF: fdt:Machine model: sun8iw21 [ 0.000000] ion_mem_reserve: err format for ion reserve list! [ 0.000000] disp reserve base 0x5df1a000 ,size 0x3e8000 [ 0.000000] Reserved memory: created DMA memory pool at 0x47000000, size 0 Mi [ 0.000000] OF: reserved mem: initialized node vdev0buffer@47000000, compatib [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 129920 [ 0.000000] free_area_init_node: node 0, pgdat c0a68314, node_mem_map dfbf800 [ 0.000000] Normal zone: 1024 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 129920 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignoreootwait init=/pseudo_init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:boot@lk0p7 cma= mac_addr= wifi_mac= bt_mac= selinux= specialstr= coherent_pool=32K iotype=2 androidboot.boot_type=2 gpt=1 androidboot.verifiedbootstate=<NULL> uboot_serve=4096000,0x5df1a000 bootreason=usb androidboot.dramsize=512 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 499280K/519680K available (6144K kernel code, 420K rwdatahmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0700000 (7136 kB) [ 0.000000] .init : 0xc0900000 - 0xc0a00000 (1024 kB) [ 0.000000] .data : 0xc0a00000 - 0xc0a693d0 ( 421 kB) [ 0.000000] .bss : 0xc0a693d0 - 0xc0a95464 ( 177 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] sunxi_efuse_readn failed:-13 [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_ [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (ph [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: [ 0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 43980 [ 0.000019] Switching to timer-based delay loop, resolution 41ns [ 0.000191] Console: colour dummy device 80x30 [ 0.000214] Calibrating delay loop (skipped), value calculated using timer fr [ 0.000228] pid_max: default: 32768 minimum: 301 [ 0.000415] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000427] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000959] CPU: Testing write buffer coherency: ok [ 0.001468] Setting up static identity map for 0x40100000 - 0x40100058 [ 0.002977] devtmpfs: initialized [ 0.035661] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 [ 0.036137] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma [ 0.036162] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.036311] atomic64_test: passed [ 0.036322] pinctrl core: initialized pinctrl subsystem [ 0.037364] NET: Registered protocol family 16 [ 0.038097] DMA: preallocated 32 KiB pool for atomic coherent allocations [ 0.040632] dump_class_init,857, success [ 0.069548] cpuidle: using governor menu [ 0.070730] platform 2010000.iommu: iova_base: 0x48400000 [ 0.071191] sunxi iommu: irq = 22 [ 0.091193] sun8iw21p1-pinctrl pio: initialized sunXi PIO driver [ 0.092939] sunxi hwspinlock vbase:0xe0822000 [ 0.094764] iommu: Adding device npu to group 0 [ 0.096428] iommu: Adding device 1c0e000.ve to group 0 [ 0.110570] iommu: Adding device 5410000.g2d to group 0 [ 0.116905] iommu: Adding device 5908000.tdm to group 0 [ 0.117661] iommu: Adding device 5900000.isp to group 0 [ 0.118395] iommu: Adding device 58ffffc.isp to group 0 [ 0.119196] iommu: Adding device 58ffff8.isp to group 0 [ 0.120411] iommu: Adding device 58ffff4.isp to group 0 [ 0.120849] iommu: Adding device 5800800.vind:isp@4 to group 0 [ 0.121606] iommu: Adding device 5910000.scaler to group 0 [ 0.122065] iommu: Adding device 590fffc.scaler to group 0 [ 0.122458] iommu: Adding device 590fff8.scaler to group 0 [ 0.123021] iommu: Adding device 590fff4.scaler to group 0 [ 0.123657] iommu: Adding device 5910400.scaler to group 0 [ 0.124296] iommu: Adding device 59103fc.scaler to group 0 [ 0.124713] iommu: Adding device 59103f8.scaler to group 0 [ 0.125270] iommu: Adding device 59103f4.scaler to group 0 [ 0.125912] iommu: Adding device 5910800.scaler to group 0 [ 0.126501] iommu: Adding device 59107fc.scaler to group 0 [ 0.126889] iommu: Adding device 59107f8.scaler to group 0 [ 0.127383] iommu: Adding device 59107f4.scaler to group 0 [ 0.128097] iommu: Adding device 5910c00.scaler to group 0 [ 0.128526] iommu: Adding device 5910bfc.scaler to group 0 [ 0.129135] iommu: Adding device 5910bf8.scaler to group 0 [ 0.129527] iommu: Adding device 5910bf4.scaler to group 0 [ 0.131156] iommu: Adding device vinc0 to group 0 [ 0.131702] iommu: Adding device vinc1 to group 0 [ 0.132323] iommu: Adding device vinc4 to group 0 [ 0.132991] iommu: Adding device vinc5 to group 0 [ 0.133783] iommu: Adding device vinc8 to group 0 [ 0.134206] iommu: Adding device vinc9 to group 0 [ 0.134806] iommu: Adding device vinc12 to group 0 [ 0.135336] iommu: Adding device vinc13 to group 0 [ 0.141333] iommu: Adding device e907_rproc@0 to group 0 [ 0.141713] iommu: Adding device rpbuf_controller@0 to group 0 [ 0.184486] pwm module init! [ 0.188741] sunxi-pm debug v3.10 [ 0.192986] SCSI subsystem initialized [ 0.193707] usbcore: registered new interface driver usbfs [ 0.193890] usbcore: registered new interface driver hub [ 0.194042] usbcore: registered new device driver usb [ 0.194347] sunxi_i2c_adap_init()2748 - init [ 0.194805] sunxi_i2c_probe()2443 - [i2c0] twi_drv_used = 0 [ 0.194821] sunxi_i2c_probe()2450 - [i2c0] twi_pkt_interval = 0 [ 0.194892] twi_regulator_request()647 - [i2c0] regulator not found(isn't con [ 0.194902] twi_request_gpio()463 - [i2c0] init name: (null) [ 0.195739] sunxi_i2c_probe()2443 - [i2c1] twi_drv_used = 0 [ 0.195756] sunxi_i2c_probe()2450 - [i2c1] twi_pkt_interval = 0 [ 0.195826] twi_regulator_request()647 - [i2c1] regulator not found(isn't con [ 0.195836] twi_request_gpio()463 - [i2c1] init name: (null) [ 0.197175] sunxi_i2c_probe()2443 - [i2c2] twi_drv_used = 0 [ 0.197193] sunxi_i2c_probe()2450 - [i2c2] twi_pkt_interval = 0 [ 0.197266] twi_regulator_request()647 - [i2c2] regulator not found(isn't con [ 0.197276] twi_request_gpio()463 - [i2c2] init name: (null) [ 0.199073] sunxi_i2c_probe()2443 - [i2c3] twi_drv_used = 0 [ 0.199091] sunxi_i2c_probe()2450 - [i2c3] twi_pkt_interval = 0 [ 0.199167] twi_regulator_request()647 - [i2c3] regulator not found(isn't con [ 0.199177] twi_request_gpio()463 - [i2c3] init name: (null) [ 0.200813] sunxi_i2c_probe()2443 - [i2c4] twi_drv_used = 0 [ 0.200830] sunxi_i2c_probe()2450 - [i2c4] twi_pkt_interval = 0 [ 0.200901] twi_regulator_request()647 - [i2c4] regulator not found(isn't con [ 0.200911] twi_request_gpio()463 - [i2c4] init name: (null) [ 0.202013] axp20x-i2c 4-0034: AXP20x variant AXP2101 found [ 0.218264] random: fast init done [ 0.233327] axp20x-i2c 4-0034: AXP20X driver loaded [ 0.233817] media: Linux media interface: v0.10 [ 0.233969] Linux video capture interface: v2.00 [ 0.237572] ion_parse_dt_heap_common: id 0 type 0 name sys_user align 1000 [ 0.237905] ion_parse_dt_heap_common: id 4 type 4 name cma align 1000 [ 0.239117] Advanced Linux Sound Architecture Driver Initialized. [ 0.240177] Bluetooth: Core ver 2.22 [ 0.240342] NET: Registered protocol family 31 [ 0.240353] Bluetooth: HCI device and connection manager initialized [ 0.240375] Bluetooth: HCI socket layer initialized [ 0.240388] Bluetooth: L2CAP socket layer initialized [ 0.240430] Bluetooth: SCO socket layer initialized [ 0.243558] G2D: rcq version initialized.major:251 [ 0.245328] clocksource: Switched to clocksource arch_sys_counter [ 0.273060] udc_init,0 [ 0.274151] thermal thermal_zone1: power_allocator: sustainable_power will be [ 0.274463] thermal thermal_zone2: power_allocator: sustainable_power will be [ 0.274635] NET: Registered protocol family 2 [ 0.285782] TCP established hash table entries: 16 (order: -6, 64 bytes) [ 0.285801] TCP bind hash table entries: 16 (order: -6, 64 bytes) [ 0.285811] TCP: Hash tables configured (established 16 bind 16) [ 0.285875] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.285895] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.286098] NET: Registered protocol family 1 [ 0.286700] sunxi_spi_probe()2259 - [spi2] SPI MASTER MODE [ 0.286767] sunxi_spi_resource_get()1908 - Failed to get sample mode [ 0.286777] sunxi_spi_resource_get()1913 - Failed to get sample delay [ 0.286786] sunxi_spi_resource_get()1917 - sample_mode:aaaaffff sample_delay: [ 0.286816] spi2 supply spi not found, using dummy regulator [ 0.286893] sunxi_spi_request_gpio()1883 - [spi2] Pinctrl init spi2 [ 0.287014] sunxi_spi_clk_init()1954 - [spi2] mclk 100000000 [ 0.287485] spi spi2: registered master spi2 [ 0.287618] spi spi2.0: setup mode 0, 8 bits/w, 100000000 Hz max --> 0 [ 0.288026] spi spi2: registered child spi2.0 [ 0.288063] sunxi_spi_probe()2339 - [spi2]: driver probe succeed, base e08380 [ 0.292406] sunxi_sid_driver_init+0x0/0x10 complete comp. [ 0.293515] workingset: timestamp_bits=29 max_order=17 bucket_order=0 [ 0.310096] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.314243] io scheduler noop registered [ 0.314259] io scheduler deadline registered [ 0.314545] io scheduler cfq registered (default) [ 0.316223] [DISP]disp_module_init [ 0.317310] [DISP]disp_module_init finish [ 0.326240] uart0: ttyS0 at MMIO 0x2500000 (irq = 289, base_baud = 1500000) i [ 0.326273] sw_console_setup()2050 - console setup baud 115200 parity n bits [ 1.551851] console [ttyS0] enabled [ 1.557218] uart3: ttyS3 at MMIO 0x2500c00 (irq = 290, base_baud = 1500000) i [ 1.567530] misc dump reg init [ 1.571737] npu[1][1] vipcore, platform driver device=0xdf59c410 [ 1.578767] npu[1][1] vipcore irq number is 291. [ 1.583955] gckvip_drv_adjust_param 232 SUCCESS [ 1.589175] Want set pclk rate(600000000) support(600000000) real(600000000) [ 1.597269] Want set mclk rate(600000000) support(600000000) real(600000000) [ 1.605197] npu[1][1] This device support 64bits DMA [ 1.611273] npu[1][1] core_0, request irqline=291, name=vipcore_0 [ 1.618404] npu[1][1] =======vipcore parameter===== [ 1.623888] npu[1][1] registerMemBase 0x03050000, [ 1.629715] npu[1][1] registerMemSize 0x00020000, [ 1.635521] npu[1][1] irqLine 0x00000123, [ 1.641292] npu[1][1] contiguousSize 0x00100000 [ 1.646942] npu[1][1] contiguousBase 0x30000000 [ 1.652519] npu[1][1] vipContiguousBase 0x0 [ 1.657445] npu[1][1] drvType 0x00000000 [ 1.663020] npu[1][1] AXISramSize 0x00000000 [ 1.668619] npu[1][1] AXISramBaseAddress 0x00000000 [ 1.674194] npu[1][1] VIPSramSize 0x00020000 [ 1.679783] npu[1][1] VIPSramBaseAddress 0x00400000 [ 1.685370] npu[1][1] sysHeapSize 0x00200000 [ 1.690946] npu[1][1] =============================== [ 1.696702] npu[1][1] VIPLite driver version 1.8.1.0-AW-2022-07-26 [ 1.704866] sun8iw21p1-pinctrl pio: expect_func as:fanout0, but muxsel(3) is [ 1.713981] sunxi-wlan soc@03000000:wlan@0: wlan_busnum (1) [ 1.720317] sunxi-wlan soc@03000000:wlan@0: wlan power voltage (3300000) [ 1.727886] sunxi-wlan soc@03000000:wlan@0: wlan io voltage (3300000) [ 1.735125] sunxi-wlan soc@03000000:wlan@0: wlan_power_num (1) [ 1.741763] sunxi-wlan soc@03000000:wlan@0: wlan_power_name (axp2101-dcdc1) [ 1.749625] sunxi-wlan soc@03000000:wlan@0: io_regulator_name (axp2101-dcdc1) [ 1.757710] sunxi-wlan soc@03000000:wlan@0: wlan_regon gpio=239 mul-sel=1 p [ 1.768308] sunxi-wlan soc@03000000:wlan@0: get gpio chip_en failed [ 1.775384] sunxi-wlan soc@03000000:wlan@0: wlan_hostwake gpio=199 mul-sel=1 [ 1.786446] sunxi-wlan soc@03000000:wlan@0: clk_name () [ 1.794339] libphy: Fixed MDIO Bus: probed [ 1.799915] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.807782] get ehci0-controller, regulator_io is no nocare [ 1.814048] get ehci0-controller wakeup-source is fail. [ 1.820127] sunxi ehci0-controller don't init wakeup source [ 1.826569] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi [ 1.838732] [sunxi-ehci0]: Not init ehci0 [ 1.843702] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.851201] get ohci0-controller, regulator_io is no nocare [ 1.857528] get ohci0-controller wakeup-source is fail. [ 1.863537] sunxi ohci0-controller don't init wakeup source [ 1.869938] [sunxi-ohci0]: probe, pdev->name: 4101000.ohci0-controller, sunxi [ 1.879669] [sunxi-ohci0]: Not init ohci0 [ 1.884794] usbcore: registered new interface driver uas [ 1.891190] usbcore: registered new interface driver usb-storage [ 1.898238] usbcore: registered new interface driver ums-alauda [ 1.905133] usbcore: registered new interface driver ums-cypress [ 1.912095] usbcore: registered new interface driver ums-datafab [ 1.919190] usbcore: registered new interface driver ums_eneub6250 [ 1.926425] usbcore: registered new interface driver ums-freecom [ 1.933420] usbcore: registered new interface driver ums-isd200 [ 1.940289] usbcore: registered new interface driver ums-jumpshot [ 1.947422] usbcore: registered new interface driver ums-karma [ 1.954229] usbcore: registered new interface driver ums-onetouch [ 1.961357] usbcore: registered new interface driver ums-realtek [ 1.968446] usbcore: registered new interface driver ums-sddr09 [ 1.975428] usbcore: registered new interface driver ums-sddr55 [ 1.982229] usbcore: registered new interface driver ums-usbat [ 1.989019] usb_serial_number:20080411 [ 1.993567] gt911 driver and device has match! [ 1.998908] get gpios success! [ 2.002437] cd gt911_ts_reset [ 2.336255] input: gt911 as /devices/platform/soc/twi2/i2c-2/2-005d/input/inp [ 2.345199] gt911 handler irq number: 231 [ 2.356901] input: axp2101-pek as /devices/platform/soc/twi4/i2c-4/4-0034/axp [ 2.368452] sunxi_gpadc_init,1949, success [ 2.373428] sunxi_gpadc_setup: get channel scan data failed [ 2.381150] input: sunxi-gpadc0 as /devices/virtual/input/input2 [ 2.390118] sunxi-rtc rtc: rtc core: registered sunxi-rtc as rtc0 [ 2.397296] sunxi-rtc rtc: RTC enabled [ 2.401568] fix to cold boot, save boot reason [ 2.407088] i2c /dev entries driver [ 2.412723] sunxi cedar version 0.1 [ 2.417347] VE: install start!!! [ 2.417347] [ 2.422703] VE: cedar-ve the get irq is 292 [ 2.427636] VE: regs_csi = e0877000 [ 2.432139] VE: ve_proc_mgr: flag = 1 [ 2.432139] [ 2.438207] VE: install end!!! [ 2.438207] [ 2.443754] google_vp9: sunxi google vp9 version 0.1 [ 2.453781] axp2101_charger: read chipid = 4a [ 2.453781] [ 2.467886] thermal thermal_zone3: power_allocator: sustainable_power will be [ 2.499328] sunxi-wdt 20500a0.watchdog: Watchdog enabled (timeout=16 sec, now [ 2.509357] Bluetooth: HCI UART driver ver 2.2.d448471.20181218-163903 [ 2.517065] Bluetooth: HCI UART protocol H4 registered [ 2.522837] Bluetooth: HCI H4 protocol initialized [ 2.529327] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 01.00.07 [ 2.538401] axp2101_charger: the gauge have been reset, need to reload param [ 2.538401] [ 2.548509] bt_fdi debugfs_init [ 2.585850] cpuidle: enable-method property 'psci' found operations [ 2.594505] sunxi-mmc sdc2: SD/MMC/SDIO Host Controller Driver(v3.59 2022-4-2 [ 2.603864] sunxi-mmc sdc2: ***ctl-spec-caps*** 308 [ 2.610214] sunxi-mmc sdc2: No vdmmc regulator found [ 2.615897] sunxi-mmc sdc2: No vd33sw regulator found [ 2.621557] sunxi-mmc sdc2: No vd18sw regulator found [ 2.627249] sunxi-mmc sdc2: No vq33sw regulator found [ 2.632907] sunxi-mmc sdc2: No vq18sw regulator found [ 2.638991] sunxi-mmc sdc2: set host busy [ 2.643537] mmc:failed to get gpios [ 2.647765] sunxi-mmc sdc2: sdc set ios:clk 0Hz bm PP pm UP vdd 22 width 1 ti [ 2.685368] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm PP pm ON vdd 22 width [ 2.705367] Unable to handle kernel NULL pointer dereference at virtual addre [ 2.714434] pgd = c0004000 [ 2.717460] [00000000] *pgd=00000000 [ 2.721469] Internal error: Oops: 5 [#1] PREEMPT ARM [ 2.727026] Modules linked in: [ 2.730450] CPU: 0 PID: 0 Comm: swapper Not tainted 4.9.191 #434 [ 2.737176] Hardware name: sun8iw21 [ 2.741080] task: c0a0adb8 task.stack: c0a00000 [ 2.746159] PC is at de_feat_get_num_screens+0x8/0x14 [ 2.751819] LR is at disp_is_enable+0x8/0x70 [ 2.756601] pc : [<c0316d0c>] lr : [<c02f3948>] psr: 60000193 [ 2.756601] sp : c0a01f38 ip : 00000002 fp : 00000000 [ 2.769465] r10: 00e2fc45 r9 : 00002380 r8 : 00000001 [ 2.775316] r7 : 00004dff r6 : 00000018 r5 : 00004dff r4 : c0a5da74 [ 2.782628] r3 : 00000000 r2 : df6440f0 r1 : ffffffff r0 : 00000000 [ 2.789941] Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment non [ 2.798032] Control: 10c5387d Table: 40004059 DAC: 00000051 [ 2.804467] Process swapper (pid: 0, stack limit = 0xc0a00208) [ 2.811000] Stack: (0xc0a01f38 to 0xc0a02000) [ 2.815878] 1f20: c0a5d [ 2.825044] 1f40: 00000018 00004dff 00000001 c0468880 dfbb1780 00004dff 00002 [ 2.834209] 1f60: 00000000 dec30400 00000000 00000000 00000000 00000000 00000 [ 2.843374] 1f80: 0130ade2 00000000 00000000 00000000 00000000 dec30400 df644 [ 2.852540] 1fa0: 00000000 c0a07074 c09268c4 00000000 00000000 c013da90 c0a07 [ 2.861705] 1fc0: ffffffff ffffffff 00000000 c090065c 00000000 c09268c4 00000 [ 2.870871] 1fe0: c0a07020 c09268c0 c0a0c034 40004059 410fc075 40008078 00000 [ 2.880048] [<c0316d0c>] (de_feat_get_num_screens) from [<c02f3948>] (disp_is [ 2.889707] [<c02f3948>] (disp_is_enable) from [<c0468880>] (menu_select+0x3d [ 2.898488] [<c0468880>] (menu_select) from [<c013da90>] (cpu_startup_entry+0 [ 2.907560] [<c013da90>] (cpu_startup_entry) from [<c0900b8c>] (start_kernel+ [ 2.916727] [<c0900b8c>] (start_kernel) from [<40008078>] (0x40008078) [ 2.924043] Code: e2877010 eaffffbd e59f3008 e5933000 (e5930000) [ 2.930875] ---[ end trace 900913423bae8ff5 ]--- [ 2.936046] Kernel panic - not syncing: Attempted to kill the idle task! [ 2.943555] ---[ end Kernel panic - not syncing: Attempted to kill the idle t [ 2.951936] sunxi dump enabled [ 2.955350] dump regs done [ 2.958401] flush cache done [ 2.961635] crashdump enter -
-
@proc_c 设备树里面把disp关了试试？
Copyright © 2024 深圳全志在线有限公司 粤ICP备2021084185号 粤公网安备44030502007680号