D1S无法进入系统，硬件为Norflash，只将默认的串口0改为了串口3，其他未变，求大佬帮助

xyz743508968 LV 3

[34]HELLO! BOOT0 is starting!
[37]BOOT0 commit : 88480af
[40]set pll start
[42]periph0 has been enabled
[44]set pll end
[46][pmu]: bus read error
[48]board init ok
[50]ZQ value = 0x2d
[52]get_pmu_exist() = -1
[54]DRAM BOOT DRIVE INFO: V0.33
[57]DRAM CLK = 528 MHz
[59]DRAM Type = 2 (2:DDR2,3:DDR3)
[62]DRAMC read ODT  off.
[65]DRAM ODT off.
[67]ddr_efuse_type: 0xa
[69]DRAM SIZE =64 M
[71]dram_tpr4:0x0
[73]PLL_DDR_CTRL_REG:0xf8002b00
[76]DRAM_CLK_REG:0xc0000000
[78][TIMING DEBUG] MR2= 0x0
[83]DRAM simple test OK.
[85]dram size =64
[87]spinor id is: ef 40 18, read cmd: 0b
[90]Succeed in reading toc file head.
[94]The size of toc is 100000.
[265]Entry_name        = opensbi
[268]Entry_name        = u-boot
[272]Entry_name        = dtb
[274]Jump to second Boot.

OpenSBI auto-t113-linux-V0.8-3-ge39e937
   ____                    _____ ____ _____
  / __ \                  / ____|  _ \_   _|
 | |  | |_ __   ___ _ __ | (___ | |_) || |
 | |  | | '_ \ / _ \ '_ \ \___ \|  _ < | |
 | |__| | |_) |  __/ | | |____) | |_) || |_
  \____/| .__/ \___|_| |_|_____/|____/_____|
        | |
        |_|

Platform Name          : T-HEAD Xuantie Platform
Platform HART Features : RV64ACDFIMSUVX
Platform Max HARTs     : 1
Current Hart           : 0
Firmware Base          : 0x41fc0400
Firmware Size          : 75 KB
Runtime SBI Version    : 0.2

MIDELEG : 0x0000000000000222
MEDELEG : 0x000000000000b1ff
PMP0    : 0x0000000041fc0000-0x0000000041fdffff (A)
PMP1    : 0x0000000040000000-0x000000007fffffff (A,R,W,X)
PMP2    : 0x0000000080000000-0x00000000bfffffff (A,R,W,X)
PMP3    : 0x0000000000020000-0x0000000000027fff (A,R,W,X)
PMP4    : 0x0000000000000000-0x000000003fffffff (A,R,W)
▒** 8 printk messages dropped **
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x0000000043ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000]   DMA32 zone: 224 pages used for memmap
[    0.000000]   DMA32 zone: 0 pages reserved
[    0.000000]   DMA32 zone: 16384 pages, LIFO batch:3
[    0.000000] elf_hwcap is 0x20112d
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16160
[    0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500C00 clk_ignore_unused initcall_debug=0 console=ttyS3,115200 loglevel=8 root=/dev/mtdblock5 rootfstype=squashfs init=/sbin/init partitions=boot-resource@mtdblock1:env@mtdblock2:env-redund@mtdblock3:boot@mtdblock4:rootfs@mtdblock5:UDISK@mtdblock6 cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.hardware=sun20iw1p1 boot_type=3 androidboot.boot_type=3 gpt=1 uboot_message=2018.07-ge987def5(11/07/2022-03:11:27) mbr_offset=1556480 disp_reserve=4096000,0x0000000042afb000 androidboot.dramsize=64
[    0.000000] Dentry cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.000000] Sorting __ex_table...
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 44892K/65536K available (4371K kernel code, 406K rwdata, 1741K rodata, 152K init, 230K bss, 12452K reserved, 8192K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[    0.000000] plic: mapped 200 interrupts with 1 handlers for 2 contexts.
[    0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [0]
[    0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000006] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000025] riscv_timer_clockevent depends on broadcast, but no broadcast function available
[    0.000393] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.001030] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.001050] pid_max: default: 32768 minimum: 301
[    0.001244] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.001265] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.003417] ASID allocator initialised with 65536 entries
[    0.003620] rcu: Hierarchical SRCU implementation.
[    0.004395] devtmpfs: initialized
[    0.020271] random: get_random_u32 called from bucket_table_alloc.isra.27+0xfe/0x120 with crng_init=0
[    0.021261] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.021296] futex hash table entries: 256 (order: 0, 6144 bytes, linear)
[    0.021906] pinctrl core: initialized pinctrl subsystem
[    0.023450] NET: Registered protocol family 16
[    0.025618] DMA: preallocated 256 KiB pool for atomic allocations
[    0.026213] cpuidle: using governor menu
[    0.071848] rtc_ccu: sunxi ccu init OK
[    0.080711] clock: sunxi ccu init OK
[    0.082651] clock: sunxi ccu init OK
[    0.112624] sun6i-dma 3002000.dma-controller: sunxi dma probed
[    0.115065] iommu: Default domain type: Translated
[    0.115267] sunxi iommu: irq = 4
[    0.116602] SCSI subsystem initialized
[    0.116842] usbcore: registered new interface driver usbfs
[    0.116930] usbcore: registered new interface driver hub
[    0.117051] usbcore: registered new device driver usb
[    0.117210] videodev: Linux video capture interface: v2.00
[    0.118289] Advanced Linux Sound Architecture Driver Initialized.
[    0.119001] Bluetooth: Core ver 2.22
[    0.119098] NET: Registered protocol family 31
[    0.119110] Bluetooth: HCI device and connection manager initialized
[    0.119135] Bluetooth: HCI socket layer initialized
[    0.119154] Bluetooth: L2CAP socket layer initialized
[    0.119198] Bluetooth: SCO socket layer initialized
[    0.119502] pwm module init!
[    0.121625] g2d 5410000.g2d: Adding to iommu group 0
[    0.122200] G2D: rcq version initialized.major:252
[    0.123141] clocksource: Switched to clocksource riscv_clocksource
[    0.137357] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver
[    0.140955] NET: Registered protocol family 2
[    0.141892] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.141948] TCP established hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.141970] TCP bind hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.141984] TCP: Hash tables configured (established 512 bind 512)
[    0.142166] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.142215] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.142494] NET: Registered protocol family 1
[    0.143877] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator
[    0.144509] spi spi0: spi0 supply spi not found, using dummy regulator
[    0.144819] sunxi_spi_resource_get()2438 - [spi0] SPI MASTER MODE
[    0.144894] sunxi_spi_resource_get()2485 - sample_mode:1 sample_delay:25
[    0.145022] sunxi_spi_clk_init()2527 - [spi0] mclk 80000000
[    0.145898] sunxi_spi_probe()2978 - [spi0]: driver probe succeed, base ffffffd004058000, irq 31
[    0.148246] workingset: timestamp_bits=62 max_order=14 bucket_order=0
[    0.154541] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.154773] ntfs: driver 2.1.32 [Flags: R/W].
[    0.155107] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.175972] io scheduler mq-deadline registered
[    0.175987] io scheduler kyber registered
[    0.176950] [DISP]disp_module_init
[    0.177607] disp 5000000.disp: Adding to iommu group 0
[    0.178287] [DISP] disp_init,line:2387:
[    0.178294] smooth display screen:0 type:1 mode:4
[    0.223070] display_fb_request,fb_id:0
[    0.263392] [DISP]disp_module_init finish
[    0.264392] sunxi_sid_init()783 - insmod ok
[    0.265274] pwm-regulator: supplied by regulator-dummy
[    0.266796] disp_al_manager_apply ouput_type:1
[    0.266926] [DISP] lcd_clk_config,line:774:
[    0.266939] disp 0, clk: pll(420000000),clk(420000000),dclk(70000000) dsi_rate(70000000)
[    0.266939]      clk real:pll(420000000),clk(420000000),dclk(105000000) dsi_rate(150000000)
[    0.267280] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator
[    0.268044] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator
[    0.268614] uart uart3: uart3 supply uart not found, using dummy regulator
[    0.269011] uart3: ttyS3 at MMIO 0x2500c00 (irq = 21, base_baud = 1500000) is a SUNXI
[    0.269044] sw_console_setup()1807 - console setup baud 115200 parity n bits 8, flow n
[    0.985114] printk: console [ttyS3] enabled
[    0.991038] misc dump reg init
[    0.995596] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator
[    1.006903] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9
[    1.018246] Freeing logo buffer memory: 4000K
[    1.023243] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed
[    1.030561] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed
[    1.038002] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1)
[    1.044544] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power.
[    1.051501] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=137 assert=1
[    1.059471] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator
[    1.070816] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1
[    1.078982] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled
[    1.086744] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power.
[    1.093549] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=133 assert=0
[    1.101724] [ADDR_MGT] addr_mgt_probe: module version: v1.0.11
[    1.109576] [ADDR_MGT] addr_mgt_probe: success.
[    1.116351] spi-nor spi0.0: w25q128 (16384 Kbytes)
[    1.124195] 7 sunxipart partitions found on MTD device spi0.0
[    1.130630] Creating 7 MTD partitions on "spi0.0":
[    1.136103] 0x000000000000-0x000000180000 : "uboot"
[    1.154058] 0x000000180000-0x0000001a0000 : "boot-resource"
[    1.173999] 0x0000001a0000-0x0000001c0000 : "env"
[    1.193996] 0x0000001c0000-0x0000001e0000 : "env-redund"
[    1.214053] 0x0000001e0000-0x000000960000 : "boot"
[    1.233989] 0x000000960000-0x0000023eb000 : "rootfs"
[    1.239527] mtd: partition "rootfs" extends beyond the end of device "spi0.0" -- size truncated to 0x6a0000
[    1.264048] 0x0000023eb000-0x000001000000 : "UDISK"
[    1.269486] mtd: partition "UDISK" is out of reach -- disabled
[    1.284252] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.291568] sunxi-ehci: EHCI SUNXI driver
[    1.296756] get ehci1-controller wakeup-source is fail.
[    1.302691] sunxi ehci1-controller don't init wakeup source
[    1.309021] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xffffffe0006ad788, 0x:ffffffd004073000, irq_no:31
[    1.322557] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply drvvbus not found, using dummy regulator
[    1.335144] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator
[    1.347508] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller
[    1.354798] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1
[    1.364728] sunxi-ehci 4200000.ehci1-controller: irq 49, io mem 0x04200000
[    1.393202] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00
[    1.400971] sunxi-ehci 4200000.ehci1-controller: ehci_irq: highspeed device connect
[    1.410786] hub 1-0:1.0: USB hub found
[    1.415123] hub 1-0:1.0: 1 port detected
[    1.420548] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.427572] sunxi-ohci: OHCI SUNXI driver
[    1.432676] get ohci1-controller wakeup-source is fail.
[    1.438769] sunxi ohci1-controller don't init wakeup source
[    1.445036] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xffffffe0006adb50
[    1.455522] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply drvvbus not found, using dummy regulator
[    1.468104] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator
[    1.480454] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller
[    1.487794] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2
[    1.497662] sunxi-ohci 4200400.ohci1-controller: irq 50, io mem 0x04200400
[    1.578293] hub 2-0:1.0: USB hub found
[    1.582561] hub 2-0:1.0: 1 port detected
[    1.590204] sunxi-rtc 7090000.rtc: registered as rtc0
[    1.596072] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:40:32 UTC (2432)
[    1.605359] sunxi-rtc 7090000.rtc: sunxi rtc probed
[    1.611350] i2c /dev entries driver
[    1.615417] IR NEC protocol handler initialized
[    1.623678] usbcore: registered new interface driver uvcvideo
[    1.630082] USB Video Class driver (1.1.1)
[    1.634929] sunxi cedar version 1.1
[    1.639136] sunxi-cedar 1c0e000.ve: Adding to iommu group 0
[    1.645450] VE: install start!!!
[    1.645450]
[    1.651077] VE: cedar-ve the get irq is 6
[    1.651077]
[    1.657483] VE: ve_debug_proc_info:(____ptrval____), data:(____ptrval____), lock:(____ptrval____)
[    1.657483]
[    1.669120] VE: install end!!!
[    1.669120]
[    1.674187] VE: sunxi_cedar_probe
[    1.678164] Bluetooth: HCI UART driver ver 2.3
[    1.683235] Bluetooth: HCI UART protocol H4 registered
[    1.688956] Bluetooth: HCI UART protocol BCSP registered
[    1.695471] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10
[    1.702817] [XR_BT_LPM] bluesleep_probe: bt_wake polarity: 1
[    1.709290] [XR_BT_LPM] bluesleep_probe: host_wake polarity: 1
[    1.716066] [XR_BT_LPM] bluesleep_probe: wakeup source is disabled!
[    1.716066]
[    1.724744] [XR_BT_LPM] bluesleep_probe: uart_index(1)
[    1.733611] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40)
[    1.743553] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8
[    1.749767] sunxi-mmc 4020000.sdmmc: No vmmc regulator found
[    1.756125] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found
[    1.762554] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found
[    1.768992] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found
[    1.775516] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found
[    1.782036] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found
[    1.788600] usb 1-1: new high-speed USB device number 2 using sunxi-ehci
[    1.796150] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found
[    1.803443] sunxi-mmc 4020000.sdmmc: Got CD GPIO
[    1.808949] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail
[    1.815724] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.826923] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator
[    1.847091] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.871606] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    1.882768] sunxi-mmc 4020000.sdmmc: detmode:gpio irq
[    1.889329] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40)
[    1.899436] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8
[    1.905701] sunxi-mmc 4021000.sdmmc: No vmmc regulator found
[    1.912044] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found
[    1.918490] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found
[    1.924960] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found
[    1.931460] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found
[    1.937988] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found
[    1.944549] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found
[    1.951084] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed
[    1.960893] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.972057] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[    1.992304] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.006902] hub 1-1:1.0: USB hub found
[    2.011493] hub 1-1:1.0: 4 ports detected
[    2.016040] sunxi-mmc 4021000.sdmmc: detmode:manually by software
[    2.024101] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    2.031446] ashmem: initialized
[    2.034977] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    2.041909] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.059892] [AUDIOCODEC][sunxi_codec_parse_params][2437]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1
[    2.059892]
[    2.077281] [AUDIOCODEC][sunxi_codec_parse_params][2473]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0
[    2.088927] [AUDIOCODEC][sunxi_internal_codec_probe][2634]:codec probe finished
[    2.097188] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.110370] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present!
[    2.120381] [SNDCODEC][sunxi_card_init][583]:card init finished
[    2.127875] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    2.135469] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    2.143012] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    2.150284] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok
[    2.160087] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    2.166898] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    2.179727] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input0
[    2.192636] [SNDCODEC][sunxi_card_dev_probe][836]:register card finished
[    2.203010] NET: Registered protocol family 10
[    2.209934] Segment Routing with IPv6
[    2.214387] NET: Registered protocol family 17
[    2.219584] Bluetooth: RFCOMM TTY layer initialized
[    2.225212] Bluetooth: RFCOMM socket layer initialized
[    2.231017] Bluetooth: RFCOMM ver 1.11
[    2.270047] sunxi-i2c sunxi-i2c2: sunxi-i2c2 supply twi not found, using dummy regulator
[    2.285915] sunxi-i2c sunxi-i2c2: probe success
[    2.296483] get ehci0-controller wakeup-source is fail.
[    2.302462] sunxi ehci0-controller don't init wakeup source
[    2.308734] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe0006acff8, 0x:ffffffd0040fb000, irq_no:2e
[    2.322279] [sunxi-ehci0]: Not init ehci0
[    2.327352] get ohci0-controller wakeup-source is fail.
[    2.333410] sunxi ohci0-controller don't init wakeup source
[    2.339627] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe0006ad3c0
[    2.350083] [sunxi-ohci0]: Not init ohci0
[    2.357481] otg manager soc@3000000:usbc0@0: soc@3000000:usbc0@0 supply usbc not found, using dummy regulator
[    2.371786] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    2.381518] clk: Not disabling unused clocks
[    2.386363] ALSA device list:
[    2.389671]   #0: audiocodec
[    2.392892] alloc_fd: slot 0 not NULL!
[    2.397183] cfg80211: failed to load regulatory.db
[    2.407168] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    2.422027] devtmpfs: mounted
[    2.425686] Freeing unused kernel memory: 152K
[    2.430670] This architecture does not have kernel memory protection.
[    2.437886] Run /sbin/init as init process
[    2.443528] random: fast init done
[    2.823273] [SNDCODEC][sunxi_check_hs_detect_status][191]:plugin --> switch:1
[    3.503428]
[    3.503428] insmod_device_driver
[    3.503428]
[    3.510658] sunxi_usb_udc 4100000.udc-controller: 4100000.udc-controller supply udc not found, using dummy regulator
[    3.522831] device_chose finished 142!
[    3.537130] init: Console is alive
[    3.541370] init: - preinit -
formating /dev/by-name/UDISK to jffs2
dd: writing '/dev/by-name/UDISK': No space left on device
1+0 records in
0+0 records out
[    5.556749] mount_root: mounting /dev/root
[    5.561964] mount_root: loading kmods from internal overlay
[    5.615333] random: crng init done
[    5.859954] block: attempting to load /etc/config/fstab
[    5.901520] block: extroot: device not present, retrying in 5 seconds
[   11.022411] block: extroot: cannot find device UDISK
[   11.044450] procd: - early -
[   11.271140] procd: - ubus -
[   11.284015] procd (1): /proc/109/oom_adj is deprecated, please use /proc/109/oom_score_adj instead.
[   11.608043] procd: - init -
[   13.534247] file system registered
[   13.620861] configfs-gadget 4100000.udc-controller: failed to start g1: -19
[   13.986143] read descriptors
[   13.989371] read strings
[   15.643964] ======== XRADIO WIFI OPEN ========
[   15.649632] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31
[   15.656526] [XRADIO] Allocated hw_priv @ 000000004901d301
[   15.673288] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
[   15.689556] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
[   15.905709] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[   15.916847] [XRADIO] Detect SDIO card 1
[   15.931540] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[   15.951778] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   15.976873] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[   15.984553] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[   15.991391] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   16.006066] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   16.019874] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[   16.027425] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[   16.034984] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[   16.042527] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[   16.049292] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[   18.003329] sunxi-rfkill soc@3000000:rfkill@0: wlan power off success
[   18.110606] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[   18.121713] [XRADIO] Remove SDIO card 1
[   18.133294] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[   18.142920] [SBUS_ERR] sdio probe timeout!
[   18.147570] [XRADIO_ERR] sbus_sdio_init failed
[   18.153892] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   18.165865] xradio_core_init failed (-110)!
[   18.196921] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[   18.204616] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[   18.211443] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   18.226297] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   18.240143] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[   18.247753] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[   18.255846] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[   18.263386] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[   18.270144] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
kmodloader done
[   32.483225] usb1-vbus: disabling

xyz743508968 LV 3

就停在这里了，回车进不了系统

xyz743508968 LV 3

后来发现我插入鼠标有反应，说明系统已经起来了，控制台却无法使用，boot和内核都能打印，应该不是这两个地方的问题，猜测是文件系统配置的问题，进入SDK /tina-d1-h/target/allwinner/d1s-nezha_nor/base-files/etc下的inittab 文件:ttyS0::askfirst:/bin/ash --login 控制台串口并没有改过来，改为ttyS3就能进入系统了。