D1S 卡在uboot结束

[huerli]

使用tina sdk ，改了串口3
修改了这些地方 env.cfg

修改了board.dts

上电输出如下所示。

[192]BOOT0 commit : 88480af
[195]set pll start
[196]fix vccio detect value:0xc0
[200]periph0 has been enabled
[203]set pll end
[204][pmu]: bus read error
[207]board init ok
[209]ZQ value = 0x2d
[210]get_pmu_exist() = -1
[213]ddr_efuse_type: 0xa
[215]trefi:7.8ms
[218][AUTO DEBUG] single rank and full DQ!
[222]ddr_efuse_type: 0xa
[224]trefi:7.8ms
[226][AUTO DEBUG] rank 0 row = 13 
[229][AUTO DEBUG] rank 0 bank = 4 
[232][AUTO DEBUG] rank 0 page size = 2 KB 
[236]DRAM BOOT DRIVE INFO: V0.33
[239]DRAM CLK = 528 MHz
[241]DRAM Type = 2 (2:DDR2,3:DDR3)
[245]DRAMC read ODT  off.
[247]DRAM ODT off.
[249]ddr_efuse_type: 0xa
[252]DRAM SIZE =64 M
[254]dram_tpr4:0x0
[255]PLL_DDR_CTRL_REG:0xf8002b00
[258]DRAM_CLK_REG:0xc0000000
[261][TIMING DEBUG] MR2= 0x0
[266]DRAM simple test OK.
[268]dram size =64
[270]card no is 0
[271]sdcard 0 line count 4
[274][mmc]: mmc driver ver 2021-04-2 16:45
[283][mmc]: Wrong media type 0x0
[286][mmc]: ***Try SD card 0***
[295][mmc]: HSSDR52/SDR25 4 bit
[298][mmc]: 50000000 Hz
[300][mmc]: 14804 MB
[302][mmc]: ***SD/MMC 0 init OK!!!***
[352]Loading boot-pkg Succeed(index=0).
[356]Entry_name        = opensbi
[359]Entry_name        = u-boot
[363]Entry_name        = dtb
[365]mmc not para
�367]Jump to second Boot.

U-Boot 2018.05-g24521d6-dirty (Jun 19 2024 - 19:18:28 +0800) Allwinner Technology

[00.377]DRAM:  64 MiB
[00.379]Relocation Offset is: 01ee7000
[00.384]secure enable bit: 0
[00.387]CPU=720 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
[00.393]flash init start
[00.395]workmode = 0,storage type = 1
[00.399][mmc]: mmc driver ver uboot2018:2021-11-19 15:38:00
[00.404][mmc]: get sdc_type fail and use default host:tm1.
[00.411][mmc]: can't find node "mmc0",will add new node
[00.416][mmc]: fdt err returned <no error>
[00.420][mmc]: Using default timing para
[00.423][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.441][mmc]: card_caps:0x3000000a
[00.444][mmc]: host_caps:0x3000003f
[00.448]sunxi flash init ok
[00.450]line:703 init_clocks
[00.454]drv_disp_init
request pwm success, pwm7:pwm7:0x2000c00.
[00.474]drv_disp_init finish
[00.477]boot_gui_init:start
[00.480]set disp.dev2_output_type fail. using defval=0
[00.487]boot_gui_init:finish
partno erro : can't find partition bootloader
54 bytes read in 2 ms (26.4 KiB/s)
[00.517]bmp_name=bootlogo.bmp size 38454
38454 bytes read in 5 ms (7.3 MiB/s)
[00.549]Loading Environment from SUNXI_FLASH... OK
[00.573]out of usb burn from boot: not need burn key
[00.607]Item0 (Map) magic is bad
[00.610]the secure storage item0 copy0 magic is bad
[00.644]Item0 (Map) magic is bad
[00.647]the secure storage item0 copy1 magic is bad
[00.652]Item0 (Map) magic is bad
partno erro : can't find partition private
root_partition is rootfs
set root to /dev/mmcblk0p5
[0[00.668]LCD open finish
0.666]update part info
[00.674]update bootcmd
[00.678]change working_fdt 0x42aa6da0 to 0x42a86da0
disable nand error: FDT_ERR_BADPATH
No reserved memory region found in source FDT
[00.715]update dts
noncached_alloc(): addr = 0x42c8a080
noncached_alloc(): addr = 0x42c8a0c0
noncached_alloc(): addr = 0x42c8a100
noncached_alloc(): addr = 0x42c8a940
geth_sys_init:634: get node 'gmac0' error
geth_sys_init fail!
[00.736]Board Net Initialization Failed
[00.739]No ethernet found.
Hit any key to stop autoboot:  0