T113-S3 NAND切换NOR (32MB) 出错 Wrong Image Format

[kwongwo]

参照这位大神的帖子[tina-linux-存储介质切换] 进行切换 SPI-NAND - > SPI NOR (W25Q256) ,出现错误

Wrong Image Format for bootm command

是不是还需要配置哪里? 还是spi nor启动参数bootargs和nand的不一样?

请帮忙看看,谢谢:)

[22]HELLO! BOOT0 is starting!
[24]BOOT0 commit : adaf1174cc
[27]set pll start
[33]periph0 has been enabled
[36]set pll end
[38][pmu]: bus read error
[40]board init ok
[42]ZQ value = 0x2f
[44]get_pmu_exist() = -1
[46]DRAM BOOT DRIVE INFO: V0.33
[49]DRAM CLK = 936 MHz
[52]DRAM Type = 3 (2:DDR2,3:DDR3)
[55]DRAMC read ODT  off.
[57]DRAM ODT value: 0x42.
[60]ddr_efuse_type: 0xa
[63]DRAM SIZE =128 M
[65]dram_tpr4:0x0
[67]PLL_DDR_CTRL_REG:0xf8004d00
[70]DRAM_CLK_REG:0xc0000000
[72][TIMING DEBUG] MR2= 0x20
[80]DRAM simple test OK.
[82]rtc standby flag is 0x0, super standby flag is 0x0
[87]dram size =128
[91]4byte mode error
[92]set spi freq:50000000
[95]spinor id is: ef 40 19, read cmd: 6b
[99]Succeed in reading toc file head.
[102]The size of toc is d4000.
[140]Entry_name        = u-boot
[145]Entry_name        = optee
[149]Entry_name        = dtb
[152]Jump to second Boot.
M/TC: OP-TEE version: 6aef7bb2-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Fri Jul 23 09:25:11 UTC 2021 arm


U-Boot 2018.05-g2a1965a-dirty (Jul 10 2022 - 02:50:57 +0000) Allwinner Technology

[00.205]CPU:   Allwinner Family
[00.208]Model: sun8iw20
[00.210]DRAM:  128 MiB
[00.214]Relocation Offset is: 04f46000
[00.229]secure enable bit: 0
[00.231]smc_tee_inform_fdt failed with: -65526[00.235]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
[00.242]gic: sec monitor mode
[00.244]flash init start
[00.247]workmode = 0,storage type = 3
[00.252]spi sunxi_slave->max_hz:50000000 
SF: Detected w25q256 with page size 256 Bytes, erase size 64 KiB, total 32 MiB
[00.263]sunxi flash init ok
[00.265]line:703 init_clocks
[00.268]drv_disp_init
request pwm success, pwm7:pwm7:0x2000c00.
fdt get node offset faill: hdmi
[00.284]unable to map hdmi registers
[00.287]drv_disp_init finish
[00.293]Loading Environment from SUNXI_FLASH... OK
[00.319]boot_gui_init:start
[00.322]set disp.dev2_output_type fail. using defval=0
[00.699]set disp.fb0_width fail. using defval=0
[00.703]set disp.fb0_height fail. using defval=0
[00.707]boot_gui_init:finish
partno erro : can't find partition bootloader
** Unrecognized filesystem type **
[00.877]sunxi bmp info error : unable to open logo file bootlogo.bmp
root_partition is rootfs
set root to /dev/mtdblock5
[00.888]update part info
[00.891]update bootcmd
[00.893]change working_fdt 0x43f05e70 to 0x43ee5e70
disable nand error: FDT_ERR_NOTFOUND
[00.913]update dts
Hit any key to stop autoboot:  1 FDT ERROR:get muxsel err returned FDT_ERR_INTERNAL
sunxi_pwm_pin_set_state, fdt_set_all_pin, ret=-1
[00.939]LCD open finish
 0 
ramdisk  addr 0x41000000 0x4100000c exceed boot scope
boot  addr 0x41000000 0x4146b000
[02.675]no vendor_boot partition is found
Wrong Image Format for bootm command
ERROR: can't get kernel image!

uboot的env参数 ,setargs_nor 参数不知道对不对,setargs_nor 和setargs_nor2都试了,还是不行.

boot_dsp0=sunxi_flash read 40000000 ${dsp0_partition};bootr 40000000 0 0
boot_fastboot=fastboot
boot_from_partion=boot
boot_normal=sunxi_flash read 41000000 ${boot_partition};bootm 41000000
boot_partition=boot
boot_recovery=sunxi_flash read 43000000 extend;bootm 43000000
bootargs=earlyprintk=sunxi-uart,0x02500C00 clk_ignore_unused initcall_debug=0 console=ttyS3,115200 loglevel=8 root=/dev/mtdblock5 rootfstype=squashfs init=/pseudo_init partitions=boot-resource@mtdblock1:env@mtdblock2:env-redund@mtdblock3:boot@mtdblock4:rootfs@mtdblock5:UDISK@mtdblock6 cma=4M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.hardware=sun8iw20p1 boot_type=3 androidboot.boot_type=3 gpt=1 uboot_message=2018.05-g2a1965a-dirty(07/10/2022-02:50:57) mbr_offset=1032192 disp_reserve=4096000,0x43f50000 androidboot.dramsize=128
bootcmd=run setargs_nor boot_normal
bootdelay=1
burn_key=0
cma=4M
console=ttyS3,115200
disp_reserve=4096000,0x43f50000
dsp0_partition=dsp0
earlyprintk=sunxi-uart,0x02500C00
fdtcontroladdr=43f05e70
force_normal_boot=1
init=/pseudo_init
initcall_debug=0
loglevel=8
mac= 
mmc_root=/dev/mmcblk0p5
mtd_name=sys
nand_root=/dev/ubiblock0_5
nor_root=/dev/mtdblock5
partitions=boot-resource@mtdblock1:env@mtdblock2:env-redund@mtdblock3:boot@mtdblock4:rootfs@mtdblock5:UDISK@mtdblock6
ramdisk_size=c
ramdisk_start=41000000
ramdisk_sum=dd40c244
root_partition=rootfs
rootdelay=2
rootfstype=squashfs
setargs_nor=setenv bootargs earlyprintk=${earlyprintk} clk_ignore_unused initcall_debug=${initcall_debug} console=${console} loglevel=${loglevel} root=${nor_root} rootfstype=${rootfstype} init=${init} partitions=${partitions} cma=${cma} snum=${snum} mac_addr=${mac} wifi_mac=${wifi_mac} bt_mac=${bt_mac} specialstr=${specialstr} gpt=1

setargs_nor2=setenv bootargs ubi.mtd=${mtd_name} ubi.block=0,${root_partition} earlyprintk=${earlyprintk} clk_ignore_unused initcall_debug=${initcall_debug} console=${console} loglevel=${loglevel} root=${nor_root} rootfstype=${rootfstype} init=${init} partitions=${partitions} cma=${cma} snum=${snum} mac_addr=${mac} wifi_mac=${wifi_mac} bt_mac=${bt_mac} specialstr=${specialstr} gpt=1

sunxi_mtdparts=spi0.0:128K(boot-resource),128K(env),128K(env-redund),6400K(boot),12800K(rootfs)