用PhoenixSuit烧录T113-S3进行到10%时会重启烧录进程
-
参照购买的T113-S3板子自画了一块，将参照板子上烧录有固件的MT29F2G01ABAGDWB-IT 芯片焊接在自画的板子上能够正常启动，尝试用PhoenixSuit给自画的板子烧录固件，进行到10% 会提示错误，PhoenixSuit重新进行下一轮烧录，一直循环。filash的wp、hold引脚上拉10K电阻。
串口信息如下：
[897]fes begin commit:adaf1174cc
[900]set pll start
[906]periph0 has been enabled
[909]set pll end
[911][pmu]: bus read error
[913]board init ok
[915]beign to init dram
[917]ZQ value = 0x2f
[919]get_pmu_exist() = -1
[922]ddr_efuse_type: 0xa
[924]trefi:7.8ms
[926][AUTO DEBUG] single rank and full DQ!
[931]ddr_efuse_type: 0xa
[933]trefi:7.8ms
[935][AUTO DEBUG] rank 0 row = 13
[938][AUTO DEBUG] rank 0 bank = 8
[942][AUTO DEBUG] rank 0 page size = 2 KB
[946]DRAM BOOT DRIVE INFO: V0.33
[949]DRAM CLK = 936 MHz
[951]DRAM Type = 3 (2:DDR2,3:DDR3)
[954]DRAMC read ODT off.
[957]DRAM ODT value: 0x42.
[959]ddr_efuse_type: 0xa
[962]DRAM SIZE =128 M
[964]dram_tpr4:0x0
[966]PLL_DDR_CTRL_REG:0xf8004d00
[969]DRAM_CLK_REG:0xc0000000
[972][TIMING DEBUG] MR2= 0x20
[976]DRAM simple test OK.
[978]rtc standby flag is 0x0, super standby flag is 0x0
[984]rtc[2] value = 0x5aa5a55a
[986]eraly jump fel
[988]init dram ok
[1072]fes begin commit:adaf1174cc
[1075]set pll start
[1081]periph0 has been enabled
[1084]set pll end
[1085][pmu]: bus read error
[1088]board init ok
[1090]beign to init dram
[1092]ZQ value = 0x2d
[1094]get_pmu_exist() = -1
[1097]ddr_efuse_type: 0xa
[1099]trefi:7.8ms
[1102][AUTO DEBUG] single rank and full DQ!
[1106]ddr_efuse_type: 0xa
[1108]trefi:7.8ms
[1111][AUTO DEBUG] rank 0 row = 13
[1114][AUTO DEBUG] rank 0 bank = 8
[1117][AUTO DEBUG] rank 0 page size = 2 KB
[1121]DRAM BOOT DRIVE INFO: V0.33
[1124]DRAM CLK = 936 MHz
[1126]DRAM Type = 3 (2:DDR2,3:DDR3)
[1129]DRAMC read ODT off.
[1132]DRAM ODT value: 0x42.
[1135]ddr_efuse_type: 0xa
[1138]DRAM SIZE =128 M
[1140]dram_tpr4:0x0
[1142]PLL_DDR_CTRL_REG:0xf8004d00
[1145]DRAM_CLK_REG:0xc0000000
[1147][TIMING DEBUG] MR2= 0x20
[1151]DRAM simple test OK.
[1154]rtc standby flag is 0x0, super standby flag is 0x0
[1159]init dram okU-Boot 2018.05-g2a1965a-dirty (Jul 10 2022 - 02:50:57 +0000) Allwinner Technology
[09.005]CPU: Allwinner Family
[09.008]Model: sun8iw20
[09.010]DRAM: 128 MiB
[09.013]Relocation Offset is: 04ebd000
[09.039]secure enable bit: 0
[09.042]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz
[09.048]gic: normal mode
[09.050]flash init start
[09.052]workmode = 16,storage type = 0
try card 2
set card number 2
get card number 2
[09.060][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00
[09.067][mmc]: Is not Boot mode!
[09.070][mmc]: SUNXI SDMMC Controller Version:0x50310
[09.081][mmc]: Try SD card 2
[09.086][mmc]: mmc 2 cmd timeout 100 status 100
[09.090][mmc]: smc 2 err, cmd 8, RTO
[09.094][mmc]: mmc 2 close bus gating and reset
[09.099][mmc]: mmc 2 cmd timeout 100 status 100
[09.103][mmc]: smc 2 err, cmd 55, RTO
[09.106][mmc]: mmc 2 close bus gating and reset
[09.111][mmc]: Try MMC card 2
[09.120][mmc]: mmc 2 cmd timeout 100 status 100
[09.124][mmc]: smc 2 err, cmd 1, RTO
[09.127][mmc]: mmc 2 close bus gating and reset
[09.131][mmc]: Card did not respond to voltage select!
[09.136][mmc]: SD/MMC 2 init error!
[09.141][mmc]: mmc init product failed
MMC init failed
try emmc fail
[09.148]sunxi-spinand: AW SPINand MTD Layer Version: 1.8 20220106
[09.154]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.11 20211217
[09.162]sunxi-spinand-phy: request spi0 gpio ok
[09.166]sunxi-spinand-phy: request general tx dma channel ok!
[09.171]sunxi-spinand-phy: request general rx dma channel ok!
[09.177]sunxi-spinand-phy: set spic0 clk to 20 Mhz
[09.181]sunxi-spinand-phy: init spic0 clk ok
[09.185]sunxi-spinand-phy: detect munufacture from id table: Micron
[09.191]sunxi-spinand-phy: detect spinand id: ffff242c ffffffff
[09.197]sunxi-spinand-phy: ========== arch info ==========
[09.202]sunxi-spinand-phy: Model: MT29F2G01ABAGDWB
[09.208]sunxi-spinand-phy: Munufacture: Micron
[09.212]sunxi-spinand-phy: DieCntPerChip: 1
[09.217]sunxi-spinand-phy: BlkCntPerDie: 2048
[09.222]sunxi-spinand-phy: PageCntPerBlk: 64
[09.226]sunxi-spinand-phy: SectCntPerPage: 4
[09.230]sunxi-spinand-phy: OobSizePerPage: 64
[09.235]sunxi-spinand-phy: BadBlockFlag: 0x0
[09.240]sunxi-spinand-phy: OperationOpt: 0x8f
[09.244]sunxi-spinand-phy: MaxEraseTimes: 65000
[09.249]sunxi-spinand-phy: EccFlag: 0x0
[09.254]sunxi-spinand-phy: EccType: 6
[09.258]sunxi-spinand-phy: EccProtectedType: 5
[09.262]sunxi-spinand-phy: ========================================
[09.268]sunxi-spinand-phy:
[09.271]sunxi-spinand-phy: ========== physical info ==========
[09.276]sunxi-spinand-phy: TotalSize: 256 M
[09.281]sunxi-spinand-phy: SectorSize: 512 B
[09.285]sunxi-spinand-phy: PageSize: 2 K
[09.289]sunxi-spinand-phy: BlockSize: 128 K
[09.293]sunxi-spinand-phy: OOBSize: 64 B
[09.297]sunxi-spinand-phy: ========================================
[09.303]sunxi-spinand-phy:
[09.306]sunxi-spinand-phy: ========== logical info ==========
[09.311]sunxi-spinand-phy: TotalSize: 256 M
[09.315]sunxi-spinand-phy: SectorSize: 512 B
[09.319]sunxi-spinand-phy: PageSize: 4 K
[09.323]sunxi-spinand-phy: BlockSize: 256 K
[09.327]sunxi-spinand-phy: OOBSize: 128 B
[09.332]sunxi-spinand-phy: ========================================
[09.338]sunxi-spinand-phy: MT29F2G01ABAGDWB reset rx bit width to 1
[09.344]sunxi-spinand-phy: MT29F2G01ABAGDWB reset tx bit width to 1
[09.350]sunxi-spinand-phy: set spic0 clk to 100 Mhz
[09.354]sunxi-spinand-phy: block lock register: 0x00
[09.359]sunxi-spinand-phy: feature register: 0x10
[09.363]sunxi-spinand-phy: sunxi physic nand init end
[09.368]line:703 init_clocks
[09.371]init_clocks:finish
[09.374]Loading Environment from SUNXI_FLASH... OK
[09.378]try to burn key
[09.380]out of usb burn from boot: not need burn key
Hit any key to stop autoboot: 0
sunxi work mode=0x10
run usb efex
delay time 2500
weak:otg_phy_config
usb init ok
set address 0xf
set address 0xf ok
SUNXI_EFEX_ERASE_TAG
erase_flag = 0x12
origin_erase_flag = 0x1
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
the 0 mbr table is ok
the 1 mbr table is ok
the 2 mbr table is ok
the 3 mbr table is ok
MBR DUMP**
total mbr part 8part[0] name :boot-resource
part[0] classname :DISK
part[0] addrlo :0x8000
part[0] lenlo :0x5e8
part[0] user_type :32768
part[0] keydata :0
part[0] ro :0part[1] name :env
part[1] classname :DISK
part[1] addrlo :0x85e8
part[1] lenlo :0x1f8
part[1] user_type :32768
part[1] keydata :0
part[1] ro :0part[2] name :env-redund
part[2] classname :DISK
part[2] addrlo :0x87e0
part[2] lenlo :0x1f8
part[2] user_type :32768
part[2] keydata :0
part[2] ro :0part[3] name :boot
part[3] classname :DISK
part[3] addrlo :0x89d8
part[3] lenlo :0x26ac
part[3] user_type :32768
part[3] keydata :0
part[3] ro :0part[4] name :rootfs
part[4] classname :DISK
part[4] addrlo :0xb084
part[4] lenlo :0x1c500
part[4] user_type :32768
part[4] keydata :0
part[4] ro :0part[5] name :private
part[5] classname :DISK
part[5] addrlo :0x27584
part[5] lenlo :0x1f8
part[5] user_type :32768
part[5] keydata :0
part[5] ro :0part[6] name :rootfs_data
part[6] classname :DISK
part[6] addrlo :0x2777c
part[6] lenlo :0x49700
part[6] user_type :32768
part[6] keydata :0
part[6] ro :0part[7] name :UDISK
part[7] classname :DISK
part[7] addrlo :0x70e7c
part[7] lenlo :0x0
part[7] user_type :33024
part[7] keydata :0
part[7] ro :0total part: 9
mbr 0, 8000, 8000
boot-resource 1, 5e8, 8000
env 2, 1f8, 8000
env-redund 3, 1f8, 8000
boot 4, 26ac, 8000
rootfs 5, 1c500, 8000
private 6, 1f8, 8000
rootfs_data 7, 49700, 8000
UDISK 8, 0, 8100
[12.489]erase blk 0 to blk 32
need erase flash: 18
[12.519]mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)device nand0 <nand>, # parts = 4
#: name size offset mask_flags
0: boot0 0x00100000 0x00000000 1
1: uboot 0x00300000 0x00100000 1
2: secure_storage 0x00100000 0x00400000 1
3: sys 0x0fb00000 0x00500000 0active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000
defaults:
mtdids : nand0=nand
mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
[12.569]MTD info (4)
[12.571]pagesize: 0x1000
[12.573]blksize: 0x40000
[12.576]num offset bytes name
[12.579]0 0x00000000 0x00100000 boot0
[12.583]1 0x00100000 0x00300000 uboot
[12.586]2 0x00400000 0x00100000 secure_storage
[12.591]3 0x00500000 0x0fb00000 sys
[12.594]ubi attach the last part of mtd device: NO.3
[12.725]ubi0: attaching mtd4
[13.173]ubi0: scanning is finished
[13.182]ubi0: attached mtd4 (name "sys", size 251 MiB)
[13.187]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[13.193]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[13.199]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[13.206]ubi0: good PEBs: 1004, bad PEBs: 0, corrupted PEBs: 0
[13.211]ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128
[13.218]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
[13.226]ubi0: available PEBs: 0, total reserved PEBs: 1004, PEBs reserved for bad PEB handling: 40
[13.234]erase blk 0 to blk 32
[13.261]erase blk 40 to blk 2048
[15.240]sunxi-spinand: spinand secure storage ok for phy blk 32 and 33
[15.248]Item0 (Map) magic is bad
[15.251]the secure storage map is empty
[15.316]sunxi-spinand: write secure storage itme 0 ok
[15.320]erase secure storage: 0 ok
SUNXI_EFEX_MBR_TAG
mbr size = 0x10000
force mbrdevice nand0 <nand>, # parts = 4
#: name size offset mask_flags
0: boot0 0x00100000 0x00000000 1
1: uboot 0x00300000 0x00100000 1
2: secure_storage 0x00100000 0x00400000 1
3: sys 0x0fb00000 0x00500000 0active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000
defaults:
mtdids : nand0=nand
mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
[15.369]MTD info (4)
[15.370]pagesize: 0x1000
[15.373]blksize: 0x40000
[15.375]num offset bytes name
[15.379]0 0x00000000 0x00100000 boot0
[15.382]1 0x00100000 0x00300000 uboot
[15.386]2 0x00400000 0x00100000 secure_storage
[15.390]3 0x00500000 0x0fb00000 sys
[15.394]MBR info (unalign):
[15.396]partno addr sects type name
[15.401]0 0x00000000 0x00008000 0x00000001 mbr
[15.406]1 0x00008000 0x000005e8 0x00008000 boot-resource
[15.411]2 0x000085e8 0x000001f8 0x00008000 env
[15.416]3 0x000087e0 0x000001f8 0x00008000 env-redund
[15.422]4 0x000089d8 0x000026ac 0x00008000 boot
[15.426]5 0x0000b084 0x0001c500 0x00008000 rootfs
[15.431]6 0x00027584 0x000001f8 0x00008000 private
[15.437]7 0x0002777c 0x00049700 0x00008000 rootfs_data
[15.442]8 0x00070e7c 0x00000000 0x00008100 UDISK
[15.447]ubi attach the last part of mtd device: NO.3
[15.452]MBR info (align):
[15.454]partno addr sects type name
[15.459]0 0x00002800 0x000081f0 0x00000001 mbr
[15.464]1 0x0000a9f0 0x000005e8 0x00008000 boot-resource
[15.469]2 0x0000afd8 0x000001f8 0x00008000 env
[15.474]3 0x0000b1d0 0x000001f8 0x00008000 env-redund
[15.479]4 0x0000b3c8 0x00002760 0x00008000 boot
[15.484]5 0x0000db28 0x0001c6c8 0x00008000 rootfs
[15.489]6 0x0002a1f0 0x000001f8 0x00008000 private
[15.494]7 0x0002a3e8 0x00049758 0x00008000 rootfs_data
[15.500]8 0x00073b40 0x00000000 0x00008100 UDISK
[15.505]ubi attach the last part of mtd device: NO.3
[15.509]ubi attatch mtd, name: sys[15.513]ubi0: detaching mtd4
[15.516]ubi0: mtd4 is detached
[15.518]ubi0: attaching mtd4
[15.744]ubi0: scanning is finished
[15.747]ubi0: empty MTD device detected
[15.765]ubi0: attached mtd4 (name "sys", size 251 MiB)
[15.770]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[15.776]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[15.782]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[15.789]ubi0: good PEBs: 1004, bad PEBs: 0, corrupted PEBs: 0
[15.794]ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
[15.801]ubi0: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 0
[15.808]ubi0: available PEBs: 960, total reserved PEBs: 44, PEBs reserved for bad PEB handling: 40
Creating static volume mbr of size 17031168
Creating dynamic volume boot-resource of size 774144
Creating dynamic volume env of size 258048
Creating dynamic volume env-redund of size 258048
Creating dynamic volume boot of size 5160960
Creating dynamic volume rootfs of size 59609088
Creating dynamic volume private of size 258048
Creating dynamic volume rootfs_data of size 154054656
No size specified -> Using max size (10321920)
[17.902]reset last volume size to 0x4ec0
Creating dynamic volume UDISK of size 10321920
[17.949]fill gap start: volume mbr sects 0x7f80
[21.970]fill gap end: volume mbr
[21.973]update partition map
[21.975]logical area info: 960 258048 last_lba: 483839
[21.987]logical area info: 960 258048 last_lba: 483839
[21.999]logical area info: 960 258048 last_lba: 483839
[22.011]logical area info: 960 258048 last_lba: 483839
[22.023]logical area info: 960 258048 last_lba: 483839
[22.035]logical area info: 960 258048 last_lba: 483839
[22.047]logical area info: 960 258048 last_lba: 483839
[22.059]logical area info: 960 258048 last_lba: 483839
[22.070]logical area info: 960 258048 last_lba: 483839
[22.082]logical area info: 960 258048 last_lba: 483839
[22.094]logical area info: 960 258048 last_lba: 483839
[22.106]logical area info: 960 258048 last_lba: 483839
[22.118]logical area info: 960 258048 last_lba: 483839
[22.130]logical area info: 960 258048 last_lba: 483839
[22.142]logical area info: 960 258048 last_lba: 483839
[22.154]logical area info: 960 258048 last_lba: 483839
[22.165]logical area info: 960 258048 last_lba: 483839
[22.177]logical area info: 960 258048 last_lba: 483839
[22.189]logical area info: 960 258048 last_lba: 483839
[22.201]logical area info: 960 258048 last_lba: 483839
[22.213]logical area info: 960 258048 last_lba: 483839
[22.225]logical area info: 960 258048 last_lba: 483839
[22.237]logical area info: 960 258048 last_lba: 483839
[22.249]logical area info: 960 258048 last_lba: 483839
[22.260]logical area info: 960 258048 last_lba: 483839
[22.272]logical area info: 960 258048 last_lba: 483839
[22.284]logical area info: 960 258048 last_lba: 483839
[22.296]logical area info: 960 258048 last_lba: 483839
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0这种现象该怎么处理？
-
spi nand的WP HOLD需要加外部上拉，或者在uboot中开启上拉
Copyright © 2024 深圳全志在线有限公司 粤ICP备2021084185号 粤公网安备44030502007680号