全志V821 SPI驱动ST7789，初始化阶段SPI上有波形，但是无法输出图形

[mysteryli]

输出图形时，SPI上没有任何波形
启动log如下

[0]BOOT0 commit :
[0]set pll start
[1]set pll end
[1]reset_src: rtc wdg rst
[2]reset_src: det rst
[2]reset_src: pwron rst
[3]board init ok: use hosc 40M
[4]DRAM use internal ZQ!!
[4]ZQ value = 0x31
[4]DRAM BOOT DRIVE INFO: V1.02
[4]DRAM CLK = 520 MHz
[5]DRAM Type = 2 (2:DDR2,3:DDR3)
[5]DRAMC read ODT off.
[5]DRAM ODT off.
[5]ddr_clk0 = 1040 MHz
[6]trefi: 7.8us
[6]DRAM Size = 64 MB
[8]DRAM simple test OK.
[8]dram size =64
[9]set spif freq:100000000
[9]spi sample_mode:0 sample_delay:1b
[11]spinor id is: 85 20 18, read cmd: ed
[11]Succeed in reading toc file head.
[11]The size of toc is c0000.
[20]Entry_name        = opensbi
[20]Entry_name        = u-boot
[22]Entry_name        = pmboot
[22]GPT load from sector:0x0, sectors: 0x8
[38]Jump to OpenSBI: opensbi_base = 0x80fc0000, dtb_base = 0x0, uboot_base = 0x82000000

OpenSBI 92310c8ed361641fa38c20bd0073be189e0f1282
   ____                    _____ ____ _____
  / __ \                  / ____|  _ \_   _|
 | |  | |_ __   ___ _ __ | (___ | |_) || |
 | |  | | '_ \ / _ \ '_ \ \___ \|  _ < | |
 | |__| | |_) |  __/ | | |____) | |_) || |_
  \____/| .__/ \___|_| |_|_____/|____/_____|
        | |
        |_|

init msb region pma attribute
Platform Name             : sun300iw1
Platform Features         : medeleg
Platform HART Count       : 1
Platform IPI Device       : sunxi_plicsw
Platform Timer Device     : sunxi_plmt @ 40000000Hz
Platform Console Device   : sunxi_uart
Platform HSM Device       : ---
Platform PMU Device       : ---
Platform Reboot Device    : sunxi_wdt
Platform Shutdown Device  : sunxi_wdt
Firmware Base             : 0x80fc0400
Firmware Size             : 75 KB
Runtime SBI Version       : 0.3

Domain0 Name              : root
Domain0 Boot HART         : 0
Domain0 HARTs             : 0*
Domain0 Region00          : 0x80fc0000-0x80fdffff ()
Domain0 Region01          : 0x00000000-0xffffffff (R,W,X)
Domain0 Next Address      : 0x82000000
Domain0 Next Arg1         : 0x00000000
Domain0 Next Mode         : S-mode
Domain0 SysReset          : yes

Boot HART ID              : 0
Boot HART Domain          : root
Boot HART ISA             : rv32imafdcnsux
Boot HART Features        : scounteren,mcounteren,mcountinhibit,sscofpmf
Boot HART PMP Count       : 64
Boot HART PMP Granularity : 8
Boot HART PMP Address Bits: 31
Boot HART MHPM Count      : 4
Boot HART MIDELEG         : 0x00000222
Boot HART MEDELEG         : 0x0000b109


U-Boot 2018.07 (Nov 19 2025 - 22:47:09 +0800) Allwinner Technology

I2C:   ready
[00.053]DRAM:  64 MiB
[00.053]Relocation Offset is: 01f23000, reloc addr is: 83f23000
[00.056]secure enable bit: 0
[00.056]drivers/sunxi_power/pmu_axpnull.c pmu_axpnull_probe 26 axpdummy probe
FDT ERROR:fdt_get_regulator_name:get property handle twi-supply error:FDT_ERR_INTERNAL
[00.058]axp2601 pmic_bus_read fail
[00.058]BMU: AXPNULL
[00.059]CPU=960 MHz,PERI=3072 Mhz,AHB=192 Mhz, APB=96Mhz
SPI ALL:   ready
[00.061]flash init start
[00.061]workmode = 0,storage type = 3
[00.066]spi sample_mode:0 sample_delay:1b
[00.067]spif sunxi_slave->max_hz:100000000
SF: Detected py25q128ha(IO DTR) with page size 256 Bytes, erase size 64 KiB, total 16 MiB
[00.069]sunxi flash init ok
[00.071]Loading Environment from SUNXI_FLASH... OK
[00.082]get secure storage map err
[00.082]sunxi secure storage is not supported
[00.082]usb burn from boot
delay time 0
[00.092]usb prepare ok
[00.356]usb sof ok
[00.356]usb probe ok
[00.357]usb setup ok
set address 0x15
set address 0x15 ok
try to update
[00.761]do_burn_from_boot usb : have no handshake
[00.761]get secure storage map err
List file under ULI/factory
** Unrecognized filesystem type **
[00.762]get secure storage map err
[00.762]get secure storage map err
[00.763]get secure storage map err
[00.763]get secure storage map err
root_partition is rootfs
set root to /dev/mtdblock7
[00.764]update part info
[00.764]update bootcmd
[00.765]change working_fdt 0x838e2ea0 to 0x838c2ea0
[00.777]## error: update_fdt_dram_para : FDT_ERR_NOTFOUND
[00.779]update dts
Info: gmac phy mode = rmii, phy_interface = 6
FDT ERROR:get muxsel err returned FDT_ERR_INTERNAL
Error: gmac set pin failed
[00.783]Board Net Initialization Failed
[00.783]No ethernet found.
Hit any key to stop autoboot:  0
[00.857]no vendor_boot partition is found
Android's image name: sun300i_riscv32
Detect comp gzip
ERROR: reserving fdt memory region failed (addr=80ffff00 size=100)
[01.080]
Starting kernel ...

[    0.000000] Linux version 5.4.220 (l@l-Default-string) (gcc version 10.4.0 (2024-02-02_nds32le-linux-glibc-v5d-bbc31ec98)) #13 PREEMPT Wed Nov 19 22:48:16 CST 2025
[    0.000000] printk: bootconsole [earlycon0] enabled
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000083c00000, size 4 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] Reserved memory: created DMA memory pool at 0x0000000081200000, size 0 MiB
[    0.000000] OF: reserved mem: initialized node vdev0buffer@81200000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created DMA memory pool at 0x0000000081646000, size 0 MiB
[    0.000000] OF: reserved mem: initialized node e907_rpbuf@81646000, compatible id shared-dma-pool
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000080000000-0x0000000083ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000080000000-0x0000000080ffefff]
[    0.000000]   node   0: [mem 0x0000000081244000-0x0000000081643fff]
[    0.000000]   node   0: [mem 0x000000008164e000-0x0000000083ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x0000000083ffffff]
[    0.000000] On node 0 totalpages: 15793
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 15793 pages, LIFO batch:3
[    0.000000] SBI specification v0.3 detected
[    0.000000] SBI implementation ID=0x1 Version=0x10000
[    0.000000] SBI v0.2 TIME extension detected
[    0.000000] SBI v0.2 IPI extension detected
[    0.000000] SBI v0.2 RFENCE extension detected
[    0.000000] SBI SRST extension detected
[    0.000000] riscv: base ISA extensions acdfim
[    0.000000] riscv: ELF capabilities acdfim
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 15665
[    0.000000] Kernel command line: earlyprintk=sunxi-uart,0x42500000 initcall_debug=0 console=ttyS0,1500000 loglevel=8 root=/dev/mtdblock7 rootwait init=/init rdinit=/rdinit partitions=boot-resource@mtdblock1:env@mtdblock2:env-redund@mtdblock3:boot@mtdblock4:private@mtdblock5:riscv0@mtdblock6:rootfs@mtdblock7:rootfs_data@mtdblock8:UDISK@mtdblock9 cma=1M coherent_pool= androidboot.serialno=9c000c71b701c762312 wifi_mac=60:c2:2a:0d:ed:49 androidboot.hardware=sun300iw1p1 boot_type=3 androidboot.boot_type=3 gpt=1 uboot_message=2018.07(11/19/2025-22:47:09) mbr_offset=1032192 bootreason=button androidboot.dramfreq=520 androidboot.dramsize=64 mtdparts=<NULL> uboot_backup=ubootA
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.000000] Sorting __ex_table...
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 27276K/63172K available (5263K kernel code, 363K rwdata, 2019K rodata, 164K init, 288K bss, 31800K reserved, 4096K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] NR_IRQS: 72, nr_irqs: 72, preallocated irqs: 0
[    0.000000] plic: mapped 187 interrupts with 1 handlers for 2 contexts.
[    0.000000] sunxi:ccu-ng:[INFO]: Current HOSC rate is 40000000HZ
[    0.000000] AW BSP version: UNKNOWN, 2025-11-19 22:48:11
[    0.000000] sunxi:ccu-ng:[INFO]: aon_ccu: sunxi ccu init OK
[    0.000000] sunxi:ccu-ng:[INFO]: sunxi ccu common driver version: 1.2.4
[    0.000000] sunxi:ccu-ng:[INFO]: ccu: sunxi ccu init OK
[    0.000000] sunxi:ccu-ng:[INFO]: sunxi app ccu driver version: 0.7.2
[    0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [0]
[    0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x939a85c40, max_idle_ns: 440795202120 ns
[    0.000011] sched_clock: 64 bits at 40MHz, resolution 25ns, wraps every 4398046511100ns
[    0.001084] Console: colour dummy device 80x25
[    0.001159] Calibrating delay loop (skipped), value calculated using timer frequency.. 80.00 BogoMIPS (lpj=160000)
[    0.001803] pid_max: default: 32768 minimum: 301
[    0.002393] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.002727] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.005626] rcu: Hierarchical SRCU implementation.
[    0.011342] devtmpfs: initialized
[    0.032543] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.032894] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.033757] pinctrl core: initialized pinctrl subsystem
[    0.041888] phys:80000000 low vir:c0000000 non-cache:dfc80000~e3c80000
[    0.043077] NET: Registered protocol family 16
[    0.047875] sunxi:ccu-ng:[INFO]: sunxi prcm ccu driver version: 0.0.4
[    0.056201] sunxi:pin-42000000.pinctrl:[INFO]: pinctrl withstand voltage config mode=auto_hard
[    0.056451] sunxi:pin:[INFO]: sunxi pinctrl core driver version: 1.4.8
[    0.057469] sunxi:pin:[INFO]: sunxi rtc-pinctrl version: 0.0.2
[    0.060024] sunxi:pin-42000540.pinctrl:[INFO]: pinctrl withstand voltage config mode=auto_hard
[    0.064422] sunxi hwspinlock vbase:0x(ptrval)
[    0.094037] SCSI subsystem initialized
[    0.094888] usbcore: registered new interface driver usbfs
[    0.095003] usbcore: registered new interface driver hub
[    0.095388] usbcore: registered new device driver usb
[    0.095857] mc: Linux media interface: v0.10
[    0.096065] videodev: Linux video capture interface: v2.00
[    0.097304] Advanced Linux Sound Architecture Driver Initialized.
[    0.099492] sun6i-dma 43002000.dma-controller: sunxi dma probed, driver version: 1.2.11
[    0.101407] sunxi-soc-regulator 4a000800.soc_pmu0: Supply for ldo1 (ldo1) resolved to itself
[    0.101647] ldo1: supplied by regulator-dummy
[    0.102833] ion_size_pool heap_size_pool@0: no small_source configurated, use cma as default
[    0.104821] sunxi:pin-42000000.pinctrl:[INFO]: Auto power withstand voltage configuration detected, automatically exit!
[    0.105460] sunxi-twi 42502000.twi0: 42502000.twi0 supply twi not found, using dummy regulator
[    0.106771] sunxi:twi-42502000.twi0:[INFO]: v2.7.9 probe success
[    0.107758] sunxi:pwm-42000c00.pwm:[INFO]: start probe
[    0.108437] sunxi:pwm-42000c00.pwm:[INFO]: pwmchip probe success
[    0.110600] clocksource: Switched to clocksource riscv_clocksource
[    0.115043] thermal_sys: Registered thermal governor 'fair_share'
[    0.115053] thermal_sys: Registered thermal governor 'bang_bang'
[    0.115109] thermal_sys: Registered thermal governor 'step_wise'
[    0.115568] thermal_sys: Registered thermal governor 'user_space'
[    0.116028] thermal_sys: Registered thermal governor 'power_allocator'
[    0.117094] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[    0.118457] sunxi_usb_udc 44100000.udc-controller: sunxi:sunxi_usb_udc UDC Inner DMA Feature - wordaddr: -1, extend: disabled
[    0.120029] NET: Registered protocol family 2
[    0.120337] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.121545] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.121809] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.122373] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.123019] TCP: Hash tables configured (established 1024 bind 1024)
[    0.123555] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.123901] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.124714] NET: Registered protocol family 1
[    0.125544] RPC: Registered named UNIX socket transport module.
[    0.125586] RPC: Registered udp transport module.
[    0.125945] RPC: Registered tcp transport module.
[    0.126305] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.127771] sunxi-spi-ng 44026000.spi: 44026000.spi supply spi not found, using dummy regulator
[    0.128265] sunxi:spi-44026000.spi:[INFO]: bus num_1 mode_1 freq_48000000
[    0.128579] sunxi:spi-44026000.spi:[INFO]: cs num_2 mode_1
[    0.128989] of_dma_request_slave_channel: dma-names property of node '/soc@2002000/spi@44026000' missing or empty
[    0.129773] sunxi:spi-44026000.spi:[ERR]: failed to request dma tx channel -19
[    0.131148] sunxi-spi-ng 44026000.spi: registered master spi1
[    0.131425] spi spi1.0: setup mode 0, 8 bits/w, 48000000 Hz max --> 0
[    0.131991] sunxi-spi-ng 44026000.spi: registered child spi1.0
[    0.132149] sunxi:spi-44026000.spi:[INFO]: probe success (Version 2.5.4)
[    0.135941] workingset: timestamp_bits=30 max_order=13 bucket_order=0
[    0.148992] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.150462] NFS: Registering the id_resolver key type
[    0.150702] Key type id_resolver registered
[    0.150896] Key type id_legacy registered
[    0.151245] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.151744] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    0.152340] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.153762] fuse: init (API version 7.31)
[    0.155297] NET: Registered protocol family 38
[    0.155390] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.155827] io scheduler mq-deadline registered
[    0.156137] io scheduler kyber registered
[    0.179855] loop: module loaded
[    0.180852] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.180973] ehci-platform: EHCI generic platform driver
[    0.181791] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.181877] ohci-platform: OHCI generic platform driver
[    0.183666] usbcore: registered new interface driver uas
[    0.183797] usbcore: registered new interface driver usb-storage
[    0.184332] i2c /dev entries driver
[    0.185670] usbcore: registered new interface driver usbhid
[    0.185704] usbhid: USB HID core driver
[    0.187999] uart-ng uart-ng0: uart-ng0 supply uart not found, using dummy regulator
[    0.188366] sunxi:uart-ng-uart-ng0:[INFO]: cannot get the TX DMA channel!
[    0.188732] sunxi:uart-ng-uart-ng0:[INFO]: cannot get the RX DMA channel!
[    0.189291] sunxi:uart-ng:[INFO]: sunxi uart-ng driver version: 1.1.10
[    0.189781] uart-ng0: ttyS0 at MMIO 0x42500000 (irq = 134, base_baud = 12000000) is a SUNXI
[    0.190371] sunxi:uart-ng-uart-ng0:[INFO]: console setup baud 1500000 parity n bits 8, flow n
[    0.191144] sunxi:uart-ng-uart-ng0:[INFO]: uart0, select set 6, baud 1500000, uartclk 192000000 beyond rance[24000000, 120000000]
[    0.191978] printk: console [ttyS0] enabled
[    0.191978] printk: console [ttyS0] enabled
[    0.192836] printk: bootconsole [earlycon0] disabled
[    0.192836] printk: bootconsole [earlycon0] disabled
[    0.195061] sunxi:rtc-4a000c00.rtc:[WARN]: Fail to get clock 'rtc-1k'
[    0.195858] sunxi:rtc-4a000c00.rtc:[WARN]: Fail to get clock 'rtc-spi'
[    0.196671] sunxi:rtc:[INFO]:  Saving SoC boot-reason: COLD-BOOT
[    0.197365] sunxi:rtc-4a000c00.rtc:[INFO]: errata__fix_alarm_day_reg_default_value(): ALARM0_DAY_REG=0, set it to 1
[    0.198616] sunxi:rtc-4a000c00.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    0.199786] sunxi:rtc-4a000c00.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    0.201239] sunxi:rtc-4a000c00.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    0.202422] sunxi:rtc-4a000c00.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    0.203622] sunxi:rtc-4a000c00.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    0.205473] sunxi-rtc 4a000c00.rtc: registered as rtc0
[    0.206128] sunxi:rtc_sun300iw1_frun_counter:[ERR]: rtc_frun_counter_init(83): rtc frun counter src not from extern32k osc
[    0.207437] sunxi:rtc-4a000c00.rtc:[WARN]: clocksource not work: rtc free running counter
[    0.208383] sunxi:rtc-4a000c00.rtc:[INFO]: sunxi rtc probed
[    0.210873] sunxi-wdt 4a001000.watchdog: Watchdog enabled (timeout=300 sec, nowayout=0), driver version: 1.0.5
[    0.214262] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: SD/MMC/SDIO Host Controller Driver(v5.55 2024-08-26 15:32)
[    0.215734] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: ctl-spec-caps 8
[    0.216569] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: No vmmc regulator found
[    0.217402] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: No vqmmc regulator found
[    0.218261] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: No vdmmc regulator found
[    0.219152] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: No vd33sw regulator found
[    0.220020] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: No vd18sw regulator found
[    0.220885] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: No vq33sw regulator found
[    0.221750] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: No vq18sw regulator found
[    0.222632] sunxi:sunxi_mmc_host-44020000.sdmmc:[ERR]: manual set ocr
[    0.223397] sunxi:sunxi_mmc_host-44020000.sdmmc:[WARN]: Cann't get pin bias hs pinstate,check if needed
[    0.224585] sunxi:sunxi_mmc_host-44020000.sdmmc:[ERR]: Could not get store clock
[    0.225445] sunxi:sunxi_mmc_host-44020000.sdmmc:[ERR]: Could not get msi_lite clock
[    0.226924] sunxi-mmc 44020000.sdmmc: Got CD GPIO
[    0.227605] sunxi-mmc 44020000.sdmmc: sunxi:sunxi_mmc_hostcd-set-debounce is missing, function is no used
[    0.229333] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    0.242521] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    0.256844] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    0.258533] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: detmode:gpio irq
[    0.261548] sunxi:sunxi_spif-44f00000.spif:[INFO]: sample_mode:0 sample_delay:1b
[    0.262718] sunxi:sunxi_spif-44f00000.spif:[INFO]: [spi-flash0] mclk 24000000
[    0.263594] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    0.265221] sunxi:sunxi_spif-44f00000.spif:[ERR]: sunxi_spif_soft_reset timeout
[    0.267342] sunxi:sunxi_mmc_host-44020000.sdmmc:[ERR]: smc 0 p0 err, cmd 8, RTO !!
[    0.268492] sunxi:sunxi_spif-44f00000.spif:[INFO]: [spi-flash0] working clk 100000000
[    0.269393] sunxi:sunxi_mmc_host-44020000.sdmmc:[ERR]: smc 0 p0 err, cmd 55, RTO !!
[    0.271113] sunxi:sunxi_mmc_host-44020000.sdmmc:[ERR]: smc 0 p0 err, cmd 55, RTO !!
[    0.272354] sunxi_spif 44f00000.spif: py25q128ha (16384 Kbytes) IO DTR
[    0.273120] sunxi:sunxi_mmc_host-44020000.sdmmc:[ERR]: smc 0 p0 err, cmd 55, RTO !!
[    0.274536] 10 sunxipart partitions found on MTD device spif
[    0.275198] sunxi:sunxi_mmc_host-44020000.sdmmc:[ERR]: smc 0 p0 err, cmd 55, RTO !!
[    0.276126] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    0.277507] sunxi:pin-42000000.pinctrl:[INFO]: Auto power withstand voltage configuration detected, automatically exit!
[    0.278782] Creating 10 MTD partitions on "spif":
[    0.279334] 0x000000000000-0x000000100000 : "uboot"
[    0.287898] 0x000000100000-0x000000180000 : "boot-resource"
[    0.290933] 0x000000180000-0x0000001a0000 : "env"
[    0.299903] 0x0000001a0000-0x0000001c0000 : "env-redund"
[    0.302905] 0x0000001c0000-0x0000006c0000 : "boot"
[    0.311877] 0x0000006c0000-0x0000006d0000 : "private"
[    0.314832] 0x0000006d0000-0x000000800000 : "riscv0"
[    0.323883] 0x000000800000-0x000000d70000 : "rootfs"
[    0.326839] 0x000000d70000-0x000000df0000 : "rootfs_data"
[    0.335880] 0x000000df0000-0x000001000000 : "UDISK"
[    0.338850] sunxi:sunxi_spif-44f00000.spif:[INFO]: probe succeed (Version 1.0.2)
[    0.341301] sunxi:lcd_fb:[NOTE]: sunxi_lcd_fb_gpio_request, gpio_name=lcd_gpio_0, gpio=98, value=0, ret=0
[    0.342437] sunxi:lcd_fb:[NOTE]: lcd 0, driver_name st7789v,  panel_name st7789v
[    0.343342] sunxi:lcd_fb:[WARN]: lcd_panel_fun[0].cfg_panel_info is NULL
[    0.345464] sunxi:lcd_fb:[NOTE]: sunxi_lcd_fb_gpio_request, gpio_name=lcd_gpio_0, gpio=98, value=0, ret=0
[    0.346659] sunxi:lcd_fb:[NOTE]: sunxi_lcd_fb_gpio_request, gpio_name=lcd_spi_dc_pin, gpio=109, value=0, ret=0
[    0.347825] sunxi:lcd_fb:[WARN]: sunxi_lcd_fb_pwm_set_polarity pwm 0, active low
[    0.348705] spi spi1.0: setup mode 0, 8 bits/w, 48000000 Hz max --> 0
[    0.349440] sunxi:lcd_fb:[NOTE]: Init spi:bits_per_word:8 max_speed_hz:48000000 mode:0
[    0.351948] sunxi:g2d_sunxi:[INFO]: [G2D]: rcq version initialized.major:244
[    0.352793] sunxi:g2d_sunxi:[INFO]: [G2D]: g2d_module_init
[    0.354671] sunxi:gpadc:[INFO]: sunxi_gpadc_init(): 2148: gpadc class register success
[    0.356044] sunxi:gpadc-42009000.gpadc0:[WARN]: warn: sample rate not set
[    0.357248] input: sunxi-gpadc0/channel0/input0 as /devices/platform/soc@2002000/42009000.gpadc0/input/input0
[    0.359069] input: sunxi-gpadc0/channel1/input0 as /devices/platform/soc@2002000/42009000.gpadc0/input/input1
[    0.361049] sunxi:gpadc-42009000.gpadc0:[INFO]: sunxi_gpadc probe success
[    0.367912] sunxi-msgbox 43033000.msgbox: sunxi:sunxi_msgboxsunxi_msgbox_probe(): sunxi msgbox start probe
[    0.369281] sunxi-msgbox 43033000.msgbox: sunxi:sunxi_msgboxsunxi_msgbox_probe(): sunxi msgbox probe success
[    0.371797] sunxi-rproc 43030000.e907_rproc: sunxi rproc driver 2.4.3
[    0.372737] sunxi-rproc 43030000.e907_rproc: rv-cfg base: 0x43030000, va: 0xe3c9b000
[    0.373736] sunxi-rproc 43030000.e907_rproc: find rproc standby error
[    0.374867] sunxi-rproc 43030000.e907_rproc: timeout_ms: 6000
[    0.375565] sunxi-rproc 43030000.e907_rproc: reset_type: 2
[    0.376196] sunxi-rproc 43030000.e907_rproc: reg:        43031000
[    0.376911] sunxi-rproc 43030000.e907_rproc: irq_num:    163
[    0.377576] sunxi-rproc 43030000.e907_rproc: panic_on_timeout: 1
[    0.378746] sunxi-rproc 43030000.e907_rproc: register memory firmware('amp_rv0.bin') for 'e907', addr: 0x81244000, size: 2097152
[    0.380094] sunxi_remoteproc: register mem fw('amp_rv0.bin'), addr=0x0000000081244000, len=2097152
[    0.381138] sunxi-rproc 43030000.e907_rproc: is_using_kernel_fw: 0
[    0.381961] remoteproc remoteproc0: e907_rproc is available
[    0.382762] remoteproc remoteproc0: powering up e907_rproc
[    0.383402] remoteproc remoteproc0: load fw from memory
[    0.384027] remoteproc remoteproc0: checking internal firmware
[    0.384725] remoteproc remoteproc0: Booting fw image amp_rv0.bin, size 2097152
[    0.385906] sunxi-rproc 43030000.e907_rproc: handle vendor resource, type: 129
[    0.386848] sunxi-rproc 43030000.e907_rproc: add trace mem 'aw_trace_log', da: 0x81129fc0, len: 4096
[    0.388020] remoteproc remoteproc0: Physical address cast in 32bit to fit resource table format
[    0.389047] rproc_wdt remoteproc0-wdt: rproc has been booted, note that the config will be overwritten
[    0.390228] sunxi_remoteproc: unregister mem fw('amp_rv0.bin'), addr=0x0000000081244000,len=2097152
[    0.391898] Freeing amp_rv0.bin memory: 2048K
[    0.392519]  remoteproc0#vdev0buffer: assigned reserved memory node vdev0buffer@81200000
[    0.394749] virtio_rpmsg_bus virtio0: rpmsg host is online
[    0.395427]  remoteproc0#vdev0buffer: registered virtio0 (type 7)
[    0.396152] remoteproc remoteproc0: remote processor e907_rproc is now up
[    0.397008] sunxi-rproc 43030000.e907_rproc: sunxi rproc driver probe ok
[    0.398629] sunxi-rpbuf-controller rpbuf_controller0@0: assigned reserved memory node e907_rpbuf@81646000
[    0.400613] [ADDR_MGT] addr_mgt_probe: module version: v1.0.13
[    0.401820] [ADDR_MGT] addr_mgt_probe: success.
[    0.402884] NET: Registered protocol family 17
[    0.403441] NET: Registered protocol family 15
[    0.404105] Key type dns_resolver registered
[    0.416297] virtio_rpmsg_bus virtio0: creating channel sunxi,rpmsg_ctrl addr 0x400
[    0.419693] virtio_rpmsg_bus virtio0: creating channel rpbuf-service addr 0x401
[    0.420861] rpbuf_service_rpmsg virtio0.rpbuf-service.-1.1025: rpmsg device parent 0: virtio0
[    0.421868] rpbuf_service_rpmsg virtio0.rpbuf-service.-1.1025: rpmsg device parent 1: remoteproc0#vdev0buffer
[    0.426594] rpbuf_service_rpmsg virtio0.rpbuf-service.-1.1025: rpmsg device parent 2: remoteproc0
[    0.427643] rpbuf_service_rpmsg virtio0.rpbuf-service.-1.1025: rpmsg device parent 3: 43030000.e907_rproc
[    0.431637] sunxi-rpbuf-controller rpbuf_controller0@0: buffer "xradio_mtx": NULL -> remote_dummy_buffers
[    0.432820] sunxi-rpbuf-controller rpbuf_controller0@0: buffer "xradio_mrx": NULL -> remote_dummy_buffers
[    0.433954] virtio_rpmsg_bus virtio0: creating channel xrlink_rpmsg addr 0x402
[    0.441790] sunxi:rtc-4a000c00.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    0.443080] sunxi-rtc 4a000c00.rtc: setting system clock to 1970-01-01T00:00:01 UTC (1)
[    0.445723] sunxi:sound-common:[ERR]: 301 pacfg_level_trig_init(): pa-pin-0 (79) request failed
[    0.446786] sunxi:sound-common:[ERR]: 612 snd_sunxi_pa_pin_init(): pacfg_level_trig_init failed
[    0.449296] sunxi:sound-i2s:[WARN]: 2206 snd_sunxi_dts_params_init(): clk-en-post-delay missing
[    0.450334] sunxi:sound-i2s:[WARN]: 2214 snd_sunxi_dts_params_init(): clk-keep missing
[    0.452061] sunxi:sound-mach:[WARN]: 372 asoc_simple_parse_ucfmt(): set data late to default
[    0.453577] debugfs: Directory 'soc@2002000:codec_plat' with parent 'audiocodec' already present!
[    0.454886] sunxi-snd-mach soc@2002000:codec_mach: 42030000.codec <-> soc@2002000:codec_plat mapping ok
[    0.457562] sunxi:sound-mach:[WARN]: 372 asoc_simple_parse_ucfmt(): set data late to default
[    0.458626] sunxi-snd-mach soc@2002000:i2s0_mach: No 'sound-dai' property
[    0.459728] debugfs: Directory '42032000.i2s0_plat' with parent 'sndi2s0' already present!
[    0.460938] sunxi-snd-mach soc@2002000:i2s0_mach: snd-soc-dummy-dai <-> 42032000.i2s0_plat mapping ok
[    0.467923] ALSA device list:
[    0.468284]   #0: audiocodec
[    0.468651]   #1: sndi2s0
[    0.469200] sunxi:uart-ng-uart-ng0:[INFO]: uart0, select set 6, baud 1500000, uartclk 192000000 beyond rance[24000000, 120000000]
[    0.476389] VFS: Mounted root (squashfs filesystem) readonly on device 31:7.
[    0.480828] devtmpfs: mounted
[    0.481373] Freeing unused kernel memory: 164K
[    0.481919] This architecture does not have kernel memory protection.
[    0.482821] Run /init as init process
[    0.610547] +++start init 7789
mount: mounting none on /dev failed: Resource busy
boot-resource@mtdblock1:env@mtdblock2:env-redund@mtdblock3:boot@mtdblock4:private@mtdblock5:riscv0@mtdblock6:rootfs@mtdblock7:rootfs_data@mtdblock8:UDISK@mtdblock9
[    1.162603] overlayfs: upper fs does not support tmpfile.
[    1.163242] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off.
init started: BusyBox v1.33.2 (2025-06-12 13:40:09 UTC)
starting pid 95, tty '': '/etc/init.d/rcS boot'
------run rc.final file-----
Load mpp modules
[    1.358715] sunxi:pwm-42000c00.pwm:[ERR]: can't parse pwm device
[    1.449309] sunxi:vin:[WARN]: sensor_helper_probe: cannot get sensor0_cameravdd supply, setting it to NULL!
[    1.459134] sunxi:vin:[WARN]: sensor_helper_probe: cannot get sensor0_iovdd supply, setting it to NULL!
[    1.460267] sunxi:vin:[WARN]: sensor_helper_probe: cannot get sensor0_avdd supply, setting it to NULL!
[    1.461352] sunxi:vin:[WARN]: sensor_helper_probe: cannot get sensor0_dvdd supply, setting it to NULL!
[    1.478815] sunxi_usb_udc 44100000.udc-controller: 44100000.udc-controller supply udc not found, using dummy regulator
sh: write error: Invalid argument
[    1.573932] file system registered
[    1.611606] udc 44100000.udc-controller: failed to start g1: -19
sh: write error: No such device
[    1.690714] read descriptors
[    1.691078] read strings
[    1.947415] sunxi:vin:[WARN]: get csi isp clk fail
[    1.948031] sunxi:vin:[WARN]: get csi isp src clk fail
[    1.949959] sunxi:vin:[INFO]: [gc2083_mipi]PWR_ON!!!
[    1.982297] sunxi:vin:[INFO]: [gc2083_mipi]PWR_OFF!!do nothing
[    1.995165] sunxi:vin:[INFO]: vinc1 is null
[    1.996276] sunxi:vin:[INFO]: vinc5 is null
[    2.003133] configfs-gadget gadget: high-speed config #1: c
[    2.034038] sunxi:VE:[INFO]: 2238 sunxi_cedar_init(): sunxi cedar version 1.1
[    2.035308] sunxi:VE:[INFO]: 2160 sunxi_cedar_probe(): probe ve
[    2.036402] sunxi-cedar 41c0e000.ve: 41c0e000.ve supply ve not found, using dummy regulator
Load usb modules
Load wifi modules
[    2.126012] [xradio_mod_init,690][XRADIO_ALWY] xradio wlan version:XR_V1.0.0.250218
[    2.126990] [xradio_core_init,543][XRADIO_ALWY] xradio core init
[    2.128083] [xradio_rpmsg_init,191][IO] xrlink rpmsg creat succeed
[    2.129440] sunxi-rpbuf-controller rpbuf_controller0@0: "xradio_mrx" allocate payload memory: va 0x(ptrval), pa 0x0000000083c08000, len 20480
[    2.130985] sunxi-rpbuf-controller rpbuf_controller0@0: buffer "xradio_mrx" (id:1): remote_dummy_buffers -> buffers
[    2.132401] sunxi-rpbuf-controller rpbuf_controller0@0: "xradio_mtx" allocate payload memory: va 0x(ptrval), pa 0x0000000083c10000, len 12288
[    2.133885] sunxi-rpbuf-controller rpbuf_controller0@0: buffer "xradio_mtx" (id:0): remote_dummy_buffers -> buffers
[    2.135380] [xradio_rpbuf_init,555][IO] xrlink master rpbuf creat succeed
[    2.136192] [xradio_platform_init,84][PLAT] xradio_platform_init sucess 0xc13d6c00
[    2.137072] [xradio_core_init,550][XRADIO_ALWY] xradio_plat c13d6c00
[    2.137814] [xradio_core_init,553][XRADIO_ALWY] xradio add_net_dev
[    2.139982] [xradio_core_init,560][XRADIO_ALWY] xradio debug com init
[    2.140860] [xradio_core_init,564][XRADIO_ALWY] xradio queue init
[    2.141607] [xradio_core_init,569][XRADIO_ALWY] xradio platform on
[    2.142312] [xradio_core_init,574][XRADIO_ALWY] register tx and rx task
[    2.143667] [xradio_core_init,579][XRADIO_ALWY] up cmd init
[    2.144345] [xradio_core_init,584][XRADIO_ALWY] low cmd init
[    2.145016] [xradio_core_init,589][XRADIO_ALWY] hand way
[    2.146664] [xraido_low_cmd_dev_hand_way,129][CMD] Host hand way dev success.
[    2.147511] [xradio_core_init,594][XRADIO_ALWY] xradio core init Suceess
[    2.148836] [xradio_set_kernel_macaddr,454][XRADIO_ALWY] MACADDR=60:c2:2a:0d:ed:49
[    2.149898] [xradio_core_init,610][XRADIO_ALWY] AP_ADDR=60:c2:2a:0d:6d:4a
[    2.150729] [xradio_core_init,617][XRADIO_ALWY] wlan device is opening...
[    2.243542] [xradio_core_init,622][XRADIO_ALWY] wlan device is ready
[    2.244278] ======== XRADIO WIFI OPEN ========
Starting wifi_deamon....: WINF: wifimanger verion:2.0.8.5 20251119-14:13:58
WINF: **************************************
WINF: * Copyright (c) 2019-2025 Allwinner Technology Co., Ltd. ALL rights reserved
WINF: * version: 2.0.8.5 20251119-14:13:58
WINF: * module name: UNKNOWN (D)
WINF: * wifimg support mode:(sta | ap | --- | --- | ------ | -------)
WINF: * module support mode:(sta | ap | --- | --- | ------ | -------)
WINF: * actual support mode:(sta | ap | --- | --- | ------ | -------)
WINF: **************************************
WINF: wifi mode sta on success
WINF: wifi on sta success
WINF: wifi set auto reconnect enable success
mount: mounting /dev/mmcblk0p1 on /mnt/extsd failed: No such file or directory
starting pid 196, tty '/dev/console': '-/bin/sh'


BusyBox v1.33.2 (2025-06-12 13:40:09 UTC) built-in shell (ash)

 _____  _              __     _
|_   _||_| ___  _ _   |  |   |_| ___  _ _  _ _
  | |   _ |   ||   |  |  |__ | ||   || | ||_'_|
  | |  | || | || _ |  |_____||_||_|_||___||_,_|
  |_|  |_||_|_||_|_|  Tina is Based on OpenWrt!
 ----------------------------------------------
 Tina Linux (5.0, unknown)
 ----------------------------------------------
root@(none):/# [   30.956654] random: cat: uninitialized urandom read (4096 bytes read)
[   30.957697] random: cat: uninitialized urandom read (4096 bytes read)
[   30.958806] random: cat: uninitialized urandom read (4096 bytes read)
[   38.532217] random: cat: uninitialized urandom read (4096 bytes read)
[   38.533267] random: cat: uninitialized urandom read (4096 bytes read)
[   38.534263] random: cat: uninitialized urandom read (4096 bytes read)
[   56.522067] random: cat: uninitialized urandom read (4096 bytes read)
[   56.523222] random: cat: uninitialized urandom read (4096 bytes read)
[   56.524228] random: cat: uninitialized urandom read (4096 bytes read)
[  105.623932] random: cat: uninitialized urandom read (4096 bytes read)