lishengyin 发布的帖子

执行到 insmod /lib/modules/4.9.191/xr806.ko 命令时会造成堵塞.

[图片]

dmsg 信息如下:

[   13.688369] [xradio_hwio_read,147][HWIO_ERR] read request failed
[   23.698368] [xradio_hwio_write,104][HWIO_ERR] write data wait dev read state faild
[   23.698377] [xradio_txrx_thread,437][TXRX_ERR] hwio exception, reset it
[   23.698381] [xradio_gpio_deinit,160][SPI] xradio rxrd gpio deinit.
[   23.698436] [xradio_spi_deinit,230][SPI] Spi unregister driver.
[   23.698476] [xradio_spi_dev_remove,192][SPI] spi remove.
[   25.698647] [xradio_spi_init,218][SPI] Spi register driver.
[   25.698733] [xradio_spi_dev_probe,177][SPI] spi probe, setup spi.
[   25.699326] [xradio_gpio_init,107][SPI] wlan gpio rw:117, irq:116
[   25.699335] [xradio_reg_rx_ind,124][SPI] Register irq callback:116
[   25.699381] [xradio_txrx_thread,418][TXRX] xradio tx rx thread exit!
[   25.699414] [xradio_gpio_deinit,160][SPI] xradio rxrd gpio deinit.
[   25.699451] [xradio_spi_deinit,230][SPI] Spi unregister driver.
[   25.699485] [xradio_spi_dev_remove,192][SPI] spi remove.
[   25.728467] [xradio_core_init,124][XRADIO_ERR] xradio core init Failed
[   25.729565] [xradio_core_init,47][XRADIO] xradio wlan version:XR_V1.002.2023.02.09
[   25.729574] [xradio_core_init,49][XRADIO] add wlan interface dev
[   25.730384] [xradio_core_init,63][XRADIO] xradio queue init
[   25.730400] [xradio_core_init,74][XRADIO] hardware io init
[   25.730405] [xradio_spi_init,218][SPI] Spi register driver.
[   25.730487] [xradio_spi_dev_probe,177][SPI] spi probe, setup spi.
[   25.731108] [xradio_gpio_init,107][SPI] wlan gpio rw:117, irq:116
[   25.731117] [xradio_reg_rx_ind,124][SPI] Register irq callback:116
[   25.731163] [xradio_core_init,79][XRADIO] register tx and rx task
[   25.731271] [xradio_core_init,84][XRADIO] up cmd init
[   25.731328] [xradio_core_init,89][XRADIO] low cmd init
[   27.768378] [xraido_low_cmd_dev_hand_way,226][TXRX_ERR] Host hand way dev failed:0
[   27.768414] [xradio_unregister_trans,451][TXRX] txrx thread unregister.
[   35.738370] [xradio_hwio_read,147][HWIO_ERR] read request failed
[   45.748366] [xradio_hwio_write,104][HWIO_ERR] write data wait dev read state faild
[   45.748372] [xradio_txrx_thread,437][TXRX_ERR] hwio exception, reset it
[   45.748377] [xradio_gpio_deinit,160][SPI] xradio rxrd gpio deinit.
[   45.748428] [xradio_spi_deinit,230][SPI] Spi unregister driver.
[   45.748466] [xradio_spi_dev_remove,192][SPI] spi remove.
[   47.748638] [xradio_spi_init,218][SPI] Spi register driver.
[   47.748727] [xradio_spi_dev_probe,177][SPI] spi probe, setup spi.
[   47.749310] [xradio_gpio_init,107][SPI] wlan gpio rw:117, irq:116
[   47.749319] [xradio_reg_rx_ind,124][SPI] Register irq callback:116
[   47.749366] [xradio_txrx_thread,418][TXRX] xradio tx rx thread exit!
[   47.749396] [xradio_gpio_deinit,160][SPI] xradio rxrd gpio deinit.
[   47.749433] [xradio_spi_deinit,230][SPI] Spi unregister driver.
[   47.749467] [xradio_spi_dev_remove,192][SPI] spi remove.
[   47.778439] [xradio_core_init,124][XRADIO_ERR] xradio core init Failed
[   47.948765] [sound 1158][DAUDIO snd_sunxi_regulator_init] regulator missing or invalid
[   47.959127] sunxi-snd-mach soc@03000000:codec_mach: sunxi-snd-codec <-> soc@03000000:codec_plat mapping ok
[   47.960904] sunxi-snd-mach soc@03000000:daudio0_mach: snd-soc-dummy-dai <-> 2032000.daudio0_plat mapping ok
[   48.058800] udevd (452): /proc/452/oom_adj is deprecated, please use /proc/452/oom_score_adj instead.
[   48.059035] udev: starting version 142
[   49.232414] sunxi-mmc sdc0: SD/MMC/SDIO Host Controller Driver(v3.30 2022-7-20 15:45)
[   49.232627] sunxi-mmc sdc0: ***ctl-spec-caps*** 408
[   49.232644] sunxi-mmc sdc0: Can't get vmmc regulator string
[   49.232651] sunxi-mmc sdc0: Can't get vqmmc regulator string
[   49.232657] sunxi-mmc sdc0: Can't get vdmmc regulator string
[   49.232662] sunxi-mmc sdc0: Can't get vdmmc33sw regulator string
[   49.232668] sunxi-mmc sdc0: Can't get vdmmc18sw regulator string
[   49.232673] sunxi-mmc sdc0: Can't get vqmmc33sw regulator string
[   49.232679] sunxi-mmc sdc0: Can't get vqmmc18sw regulator string
[   49.232685] sunxi-mmc sdc0: Failed getting OCR mask: 0
[   49.233287] sunxi-mmc sdc0: set host busy
[   49.233296] sunxi-mmc sdc0: ***set host ocr***
[   49.233376] sunxi-mmc sdc0: Got CD GPIO
[   49.234402] sunxi-mmc sdc0: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[   49.478472] sunxi-mmc sdc0: Switching to 3.3V signalling voltage ok
[   49.508394] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   49.538578] sunxi-mmc sdc0: detmode:gpio irq
[   49.539963] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   49.543933] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   49.547158] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   49.551194] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   49.647778] mmc0: host does not support reading read-only switch, assuming write-enable
[   49.651205] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[   49.651301] sunxi-mmc sdc0: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[   49.651478] sunxi-mmc sdc0: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[   49.651542] mmc0: new high speed SDHC card at address aaaa
[   49.653966] mmcblk0: mmc0:aaaa SA32G 29.7 GiB 
[   49.657607]  mmcblk0: p1
[   49.672298] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[   51.805329] usbcore: registered new interface driver usbfs
[   51.805758] usbcore: registered new interface driver hub
[   51.806162] usbcore: registered new device driver usb
[   51.821188] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   51.821580] get drv_vbus is fail, 84
[   51.821587] get ehci0-controller, regulator_io is no nocare
[   51.821591] get ehci0-controller wakeup-source is fail.
[   51.821796] sunxi ehci0-controller don't init wakeup source
[   51.821809] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xbf8c6700, 0x:c6cd8000, irq_no:12e
[   51.821813] [sunxi-ehci0]: Not init ehci0
[   51.870157] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   51.870554] get drv_vbus is fail, 84
[   51.870562] get ohci0-controller, regulator_io is no nocare
[   51.870566] get ohci0-controller wakeup-source is fail.
[   51.870775] sunxi ohci0-controller don't init wakeup source
[   51.870862] [sunxi-ohci0]: probe, pdev->name: 4101000.ohci0-controller, sunxi_ohci: 0xbf8c6d6c
[   51.870867] [sunxi-ohci0]: Not init ohci0
[   51.930357] usb_serial_number:20080411
[   51.978756] get androidboot.mode fail
[   52.042669] get id is fail, 84
[   53.128441] 
[   53.128441] insmod_device_driver
[   53.128441] 
[   53.258673] file system registered
[   53.272263] configfs-gadget 4100000.udc-controller: failed to start g1: -19
[   53.344178] read descriptors
[   53.344196] read strings
[   53.544713] android_work: sent uevent USB_STATE=CONNECTED
[   53.563914] configfs-gadget gadget: high-speed config #1: c
[   53.564044] android_work: sent uevent USB_STATE=CONFIGURED

@tevet - make_kernel_menuconfig 搜索 CONFIG_FILE_LOCKING，打开如下配置，重新编译即可。

默认不编译POSIX标准文件锁定API，所以程序执行到文件加锁与解锁的flock()时失败。

# fw_env_main.c
    if (-1 == flock(lockfd, LOCK_EX)) {
        fprintf(stderr, "Error locking file %s\n", lockname);
        close(lockfd);
        return EXIT_FAILURE;
    }

fw_setenv 修改 env报错, 报错权限问题，但修改权限后还是不行。

root@(none):/mnt/extsd# fw_setenv boot_partition bootA
Write error on /dev/by-name/env: Operation not permitted
Error: can't write fw_env to flash

root@(none):/mnt/extsd# ll /dev/by-name/
UDISK        bootB        extend       rootfsB
bootA        env          rootfsA      rootfs_data
root@(none):/mnt/extsd# ll /dev/by-name/env 
lrwxrwxrwx    1 root     root            14 Jan  1 00:00 /dev/by-name/env -> /dev/mtdblock7

请问是还需要修改哪以一部分的权限设置。

v851s-fastboot的 麻烦看下？给个方向

tina-v851s 的fw_printfenv报错。

分区表如下：

[partition_start]

[partition]
    name         = boot
    size         = 7040
    downloadfile = "boot.fex"
    user_type    = 0x8000

[partition]
    name         = rootfs
    size         = 11264
    downloadfile = "rootfs.fex"
    user_type    = 0x8000

[partition]
    name         = extend
    size         = 7040
    downloadfile = "usr.fex"
    user_type    = 0x8000

[partition]
    name         = rootfs_data
    size         = 1024
    user_type    = 0x8000

[partition]
   name         = env
   size         = 512
   downloadfile = "env_nor.fex"
   user_type    = 0x8000

fw_env.config如下:

# Configuration file for fw_(printenv/setenv) utility.
# Up to two entries are valid, in this case the redundant
# environment sector is assumed present.
# Notice, that the "Number of sectors" is not required on NOR and SPI-dataflash.
# Futhermore, if the Flash sector size is omitted, this value is assumed to
# be the same as the Environment size, which is valid for NOR and SPI-dataflash
# Device offset must be prefixed with 0x to be parsed as a hexadecimal value.

# NOR example
# MTD device name       Device offset   Env. size       Flash sector size       Number of sectors
# /dev/mtd1             0x0000          0x4000          0x4000
# /dev/mtd2             0x0000          0x4000          0x4000

# MTD SPI-dataflash example
# MTD device name       Device offset   Env. size       Flash sector size       Number of sectors
#/dev/mtd5              0x4200          0x4200
#/dev/mtd6              0x4200          0x4200

# NAND example
#/dev/mtd0              0x4000          0x4000          0x20000                 2

# On a block device a negative offset is treated as a backwards offset from the
# end of the device/partition, rather than a forwards offset from the start.

# Block device example
#/dev/mmcblk0           0xc0000         0x20000
#/dev/mmcblk0           -0x20000        0x20000

# VFAT example
#/boot/uboot.env        0x0000          0x4000

# UBI volume
#/dev/ubi0_0            0x0             0x1f000         0x1f000
#/dev/ubi0_1            0x0             0x1f000         0x1f000

# UBI volume by name
#/dev/ubi0:env          0x0             0x1f000         0x1f000
#/dev/ubi0:env-redund   0x0             0x1f000         0x1f000

# Allwinner Tina
/dev/by-name/env        0x0000          0x20000

分区如下：

root@(none):/mnt/extsd# cat /proc/mtd 
dev:    size   erasesize  name
mtd0: 00200000 00010000 "uboot"
mtd1: 00370000 00010000 "boot"
mtd2: 00580000 00010000 "rootfs"
mtd3: 00370000 00010000 "extend"
mtd4: 00040000 00010000 "env"
mtd5: 00080000 00010000 "rootfs_data"
mtd6: 010e0000 00010000 "UDISK"

root@(none):/mnt/extsd# fw_printenv 
Error locking file /var/lock/fw_printenv.lock
root@(none):/mnt/extsd# fw_setenv 
Error locking file /var/lock/fw_printenv.lock

@yuzukitsuru 好的

v851s 在分区表中新建分区报错， 主要修改tina-fastboot-v85x/device/config/chips/v851s/configs/fastboot/linux/sys_partition_nor.fex文件。

请问新建分区，除了修改以上文件，还需要修改哪里呢？

相关格式如下:

;---------------------------------------------------------------------------------------------------------
; 说明： 脚本中的字符串区分大小写，用户可以修改"="后面的数值，但是不要修改前面的字符串
;---------------------------------------------------------------------------------------------------------


;--------------------------------------------------------------------------------------------------
;                                   固件下载参数配置
;--------------------------------------------------------------------------------------------------
;****************************************************
;    mbr的大小, 以Kbyte为单位
;****************************************************
[mbr]
size = 16

;********************************************************************************************************
;                                              分区配置
;
;
;  partition 定义范例:
;    [partition]                ;  //表示是一个分区
;    name        = USERFS2      ; //分区名称
;    size        = 16384        ; //分区大小 单位: 扇区.分区表示个数最多2^31 * 512 = 2T
;    downloadfile = "123.fex"   ; //下载文件的路径和名称，可以使用相对路径，相对是指相对于image.cfg文件所在分区。也可以使用绝对路径
;    keydata     = 1            ; //私有数据分区，重新量产数据将不丢失
;    encrypt     = 1            ; //采用加密方式烧录，将提供数据加密，但损失烧录速度
;    user_type   = ?            ; //私有用法
;    verify      = 1            ; //要求量产完成后校验是否正确
;
; 注：1、name唯一, 不允许同名
;     2、name最大12个字符
;     3、size = 0, 将创建一个无大小的空分区
;     4、为了安全和效率考虑，分区大小最好保证为16M字节的整数倍
;********************************************************************************************************
[partition_start]


[partition]
    name         = boot
    size         = 7040
    downloadfile = "boot.fex"
    user_type    = 0x8000

[partition]
    name         = rootfs
    size         = 11264
    downloadfile = "rootfs.fex"
    user_type    = 0x8000

[partition]
    name         = rootfsA
    size         = 11264
    downloadfile = "rootfs1.fex"
    user_type    = 0x8000

[partition]
    name         = extend
    size         = 7040
    downloadfile = "usr.fex"
    user_type    = 0x8000

[partition]
    name         = rootfs_data
    size         = 1024
    user_type    = 0x8000



;[partition]
;   name         = env
;   size         = 512
;   downloadfile = "env_nor.fex"
;   user_type    = 0x8000

;[partition]
;   name         = misc
;   size         = 128
;   user_type    = 0x8000

;[partition]
;   name         = bootlogo
;   size         = 768
;   downloadfile = "bootlogo.fex"
;   user_type    = 0x8000