NLJ_Moon 发布的帖子

我也遇到这个问题了，大哥解决了吗

• xr829使用报错，大家帮忙看看
  

使用创龙T113 i的核心板，创龙默认SDK使用的不是XR829，但是会把XR829的ko文件和固件一起打包，我通过inmod xr829.ko使用，出现以下问题，大佬们帮忙看看怎们解决；

• 驱动可以正常加载，加载过程如下，
• 扫描WiFi 无反应，模块无法正常使用，
  
  

root@TinaLinux:/lib/modules/5.4.61# insmod xr829.ko
[ 34.226001] ======== XRADIO WIFI OPEN ========
[ 34.231513] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31
[ 34.238325] [XRADIO] Allocated hw_priv @ 65abb3d7
[ 34.244182] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
[ 34.260599] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
[ 34.467788] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 34.474327] [XRADIO] Detect SDIO card 1
[ 34.479019] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[ 34.503409] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 34.528273] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 34.542858] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 34.564923] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[ 34.576515] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[ 34.588354] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[ 34.600868] mmc1: new high speed SDIO card at address 0001
[ 34.607506] [SBUS] XRadio Device:sdio clk=50000000
[ 34.613613] [XRADIO] XRADIO_HW_REV 1.0 detected.
[ 34.738211] [XRADIO] xradio_update_dpllctrl: DPLL_CTRL Sync=0x01400000.
[ 34.821706] [XRADIO] Bootloader complete
[ 34.920347] [XRADIO] Firmware completed.
[ 34.926350] [WSM] Firmware Label:XR_C09.08.52.73_DBG_02.122 2GHZ HT40 May 18 2021 13:36:09
[ 34.935832] [XRADIO] Firmware Startup Done.
[ 34.940741] [XRADIO_WRN] enable Multi-Rx!
[ 34.945937] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
root@TinaLinux:/lib/modules/5.4.61# ifconfig wlan0 up
[ 44.908379] ieee80211_do_open: vif_type=2, p2p=0, ch=3, addr=bc:bc:44:ed:ed:c5
[ 44.916542] [STA] !!!xradio_vif_setup: id=0, type=2, p2p=0, addr=bc:bc:44:ed:ed:c5
[ 44.931914] [AP_WRN] BSS_CHANGED_ASSOC but driver is unjoined.
root@TinaLinux:/lib/modules/5.4.61# wifi -s
Can't connect to the wifi daemon server: No such file or directory
root@TinaLinux:/lib/modules/5.4.61#

球球大家了，帮忙看看这个是什么问题，wifi命令不能使用，iw命令可以搜索wifi

问题描述：正常联网之后ping百度打印的东西和平时使用的wifi模块不一样

@awwwwa Tina 的SDK不是还能编译buildroot吗，文件系统咋buildroot上编译的

nandflash的分区为什么这么复杂，需要从mtd3中创建ubi0，文件系统挂载的时候还要创建ubi0block0_5,

使用过mount -o remount -o rw /dev/root但是没有用，
分配了3G的大小rootfs，但是实际df查看只有这么大，

@mhcsoft 大佬移植成功了吗，有什么要注意的呀

有的适合在这个目录新增文件会报错，大家有遇到吗

使用WiFi模块的时候由高延迟，大家由排查思路吗。

配置有线网的适合遇到这个问题，请教大家怎么排查？或者如何在软件上看phy芯片的状态，目前rtl8021f模块发热比较严重。

我遇到和你一样的问题了，请问你解决了吗

@waterworld 怎末解决的呀

@wyljkl 能请教一下如何调试的吗，设备树可以参考一下吗

@winyunq 能仔细讲一下如何将全志官网D1 tina中，的bluez的patch抠出来再加到自己的SDK中吗，拜托了，我也遇到这个问题了，HCI0的设备就是没有。

对蓝牙启动信息检索：

root@TinaLinux:/# dmesg | grep Bluetooth
[    0.095938] Bluetooth: Core ver 2.22
[    0.096034] Bluetooth: HCI device and connection manager initialized
[    0.096054] Bluetooth: HCI socket layer initialized
[    0.096066] Bluetooth: L2CAP socket layer initialized
[    0.096093] Bluetooth: SCO socket layer initialized
[    2.277757] Bluetooth: HCI UART driver ver 2.3
[    2.282784] Bluetooth: HCI UART protocol (null) registered
[    2.288976] Bluetooth: HCI Realtek H5 protocol initialized
[    2.314540] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10
[    2.765813] Bluetooth: RFCOMM TTY layer initialized
[    2.771378] Bluetooth: RFCOMM socket layer initialized
[    2.777167] Bluetooth: RFCOMM ver 1.11

对HCI设备相关信息检索：

root@TinaLinux:/# dmesg | grep HCI
[    0.096034] Bluetooth: HCI device and connection manager initialized
[    0.096054] Bluetooth: HCI socket layer initialized
[    2.091294] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.098616] sunxi-ehci: EHCI SUNXI driver
[    2.103554] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.110578] sunxi-ohci: OHCI SUNXI driver
[    2.277757] Bluetooth: HCI UART driver ver 2.3
[    2.282784] Bluetooth: HCI UART protocol (null) registered
[    2.288976] Bluetooth: HCI Realtek H5 protocol initialized

大家帮帮忙，看一下什么问题。