全志在线开发者论坛

qinhao4832

@kevin_allwinner 大佬，怎么小改。用哪家配置的sdk

qinhao4832

我一直按住复位键，然后上电，得到这些log：

[23]BOOT0 commit : 88480af-dirty
[26]set pll start
[28]fix vccio detect value:0xc0
[35]periph0 has been enabled
[38]set pll end
[40][pmu]: bus read error
[42]board init ok
[44]ZQ value = 0x31
[46]get_pmu_exist() = -1
[49]ddr_efuse_type: 0xa
[51]trefi:7.8ms
[53][AUTO DEBUG] single rank and full DQ!
[57]ddr_efuse_type: 0xa
[59]trefi:7.8ms
[62][AUTO DEBUG] rank 0 row = 13
[65][AUTO DEBUG] rank 0 bank = 8
[68][AUTO DEBUG] rank 0 page size = 2 KB
[72]DRAM BOOT DRIVE INFO: V0.33
[75]DRAM CLK = 936 MHz
[77]DRAM Type = 3 (2:DDR2,3:DDR3)
[80]DRAMC read ODT  off.
[83]DRAM ODT value: 0x42.
[85]ddr_efuse_type: 0xa
[88]DRAM SIZE =128 M
[90]dram_tpr4:0x0
[92]PLL_DDR_CTRL_REG:0xf8004d00
[95]DRAM_CLK_REG:0xc0000000
[98][TIMING DEBUG] MR2= 0x20
[105]DRAM simple test OK.
[108]rtc standby flag is 0x0, super standby flag is 0x0
[113]dram size =128
[115]card no is 0
[117]sdcard 0 line count 4
[120][mmc]: mmc driver ver 2021-05-21 14:47
[129][mmc]: Wrong media type 0x0
[132][mmc]: ***Try SD card 0***
[142][mmc]: HSSDR52/SDR25 4 bit
[145][mmc]: 50000000 Hz
[147][mmc]: 60014 MB
[149][mmc]: ***SD/MMC 0 init OK!!!***
[221]Loading boot-pkg Succeed(index=0).
[225]Entry_name        = u-boot
[230]Entry_name        = optee
[234]Entry_name        = dtb
[237]mmc not para
[239]Jump to second Boot.
M/TC: OP-TEE version: 6aef7bb2-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Fri Jul 23 09:25:11 UTC 2021 arm


U-Boot 2018.05-g24521d6-dirty (Jun 27 2023 - 01:57:03 -0700) Allwinner Technology

[00.292]CPU:   Allwinner Family
[00.295]Model: sun8iw20
I2C:   FDT ERROR:fdt_set_all_pin:[twi0]-->FDT_ERR_BADPATH
FDT ERROR:fdt_set_all_pin:[twi1]-->FDT_ERR_BADPATH
ready
[00.316]DRAM:  128 MiB
[00.319]Relocation Offset is: 04f01000
[00.339]secure enable bit: 0
[00.341]smc_tee_inform_fdt failed with: -65526[00.346]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
[00.352]gic: sec monitor mode
[00.355]flash init start
[00.357]workmode = 0,storage type = 1
[00.361][mmc]: mmc driver ver uboot2018:2021-11-19 15:38:00
[00.366][mmc]: get sdc_type fail and use default host:tm1.
[00.372][mmc]: can't find node "mmc0",will add new node
[00.377][mmc]: fdt err returned <no error>
[00.381][mmc]: Using default timing para
[00.384][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.403][mmc]: card_caps:0x3000000a
[00.406][mmc]: host_caps:0x3000003f
[00.410]sunxi flash init ok
[00.417]Loading Environment from SUNXI_FLASH... OK
[00.447]Item0 (Map) magic is bad
[00.449]the secure storage item0 copy0 magic is bad
[00.465]Item0 (Map) magic is bad
[00.468]the secure storage item0 copy1 magic is bad
[00.473]Item0 (Map) magic is bad
secure storage read widevine fail
[00.479]secure storage read widevine fail with:-1
secure storage read ec_key fail
[00.486]secure storage read ec_key fail with:-1
secure storage read ec_cert1 fail
[00.493]secure storage read ec_cert1 fail with:-1
secure storage read ec_cert2 fail
[00.501]secure storage read ec_cert2 fail with:-1
secure storage read ec_cert3 fail
[00.508]secure storage read ec_cert3 fail with:-1
secure storage read rsa_key fail
[00.515]secure storage read rsa_key fail with:-1
secure storage read rsa_cert1 fail
[00.523]secure storage read rsa_cert1 fail with:-1
secure storage read rsa_cert2 fail
[00.531]secure storage read rsa_cert2 fail with:-1
secure storage read rsa_cert3 fail
[00.538]secure storage read rsa_cert3 fail with:-1
[00.543]usb burn from boot
delay time 0
weak:otg_phy_config
[00.554]usb prepare ok
[01.357]overtime
[01.360]do_burn_from_boot usb : no usb exist
root_partition is rootfs
set root to /dev/mmcblk0p5
[01.370]update part info
[01.373]update bootcmd
[01.376]change working_fdt 0x43ec0e70 to 0x43ea0e70
disable nand error: FDT_ERR_BADPATH
[01.397]update dts
Hit any key to stop autoboot:  0
[02.579]no vendor_boot partition is found
Android's image name: t113-100ask
[02.590]Starting kernel ...

[02.593][mmc]: MMC Device 2 not found
[02.596][mmc]: mmc 2 not find, so not exit
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.61 (qinhao@ubuntu) (arm-openwrt-linux-muslgnueabi-gcc.bin (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) 6.4.1, GNU ld (GNU Binutils) 2.27) #96 SMP PREEMPT Fri Jul 28 00:48:06 UTC 2023
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: sun8iw20
[    0.000000] printk: bootconsole [earlycon0] enabled
[    0.001710] /cpus/cpu@0 missing clock-frequency property
[    0.007046] /cpus/cpu@1 missing clock-frequency property
[    0.099139] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator
[    0.109405] spi spi0: spi0 supply spi not found, using dummy regulator
[    0.116110] sunxi_spi_resource_get()2161 - [spi0] SPI MASTER MODE
[    0.122279] sunxi_spi_resource_get()2199 - Failed to get sample mode
[    0.128653] sunxi_spi_resource_get()2204 - Failed to get sample delay
[    0.135085] sunxi_spi_resource_get()2208 - sample_mode:-1431633921 sample_delay:-1431633921
[    0.143520] sunxi_spi_clk_init()2250 - [spi0] mclk 100000000
[    0.149755] sunxi_spi_probe()2663 - [spi0]: driver probe succeed, base c881f000, irq 40
[    0.206032] disp 5000000.disp: 5000000.disp supply vcc-lcd not found, using dummy regulator
[    0.214597] disp 5000000.disp: 5000000.disp supply vcc-pd not found, using dummy regulator
[    0.228173] display_fb_request,fb_id:0
[    0.234403] [DISP] Fb_copy_boot_fb,line:1443:
[    0.234407] no boot_fb0
[    0.241665] disp_al_manager_apply ouput_type:0
[    0.247413] [DISP] lcd_clk_config,line:732:
[    0.247425] disp 0, clk: pll(198000000),clk(198000000),dclk(33000000) dsi_rate(198000000)
[    0.247425]      clk real:pll(288000000),clk(288000000),dclk(48000000) dsi_rate(0)
[    0.247663] sunxi_sid_init()551 - insmod ok
[    0.252451] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator
[    0.268340] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator
[    0.291532] uart uart3: get regulator failed
[    0.295807] uart uart3: uart3 supply uart not found, using dummy regulator
[    0.302973] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n
▒[    0.486898] [DISP] disp_device_attached_and_enable,line:233:
[    0.486903] attached ok, mgr0<-->dev0
[    0.497402] [DISP] disp_device_attached_and_enable,line:236:
[    0.497410] type:1,mode:0,fmt:rgb,bits:8bits,eotf:4,cs:0 dvi_hdmi:2, range:2 scan:0 ratio:8
[    0.515034] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator
[    0.527589] Failed to alloc md5
[    0.531122] eth0: Use random mac address
[    0.535923] sunxi-ehci: EHCI SUNXI driver
[    0.540840] sunxi-ohci: OHCI SUNXI driver
[    0.545988] sunxi cedar version 1.1
[    0.581686] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present!
[    0.591588] [SNDCODEC][sunxi_card_init][583]:card init finished
[    0.617802] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator
[    0.629294] sunxi-i2c sunxi-i2c1: sunxi-i2c1 supply twi not found, using dummy regulator
[    0.640322] rtc-rx8010 1-0032: Frequency stop was detected
[    0.646950] rtc-rx8010 1-0032: Frequency stop detected
[    0.653163] rtc-rx8010 1-0032: Frequency stop detected
[    0.658960] rtc-rx8010 1-0032: hctosys: unable to read the hardware clock
[    0.669009] debugfs: Directory '2031000.dmic' with parent 'snddmic' already present!
[    0.679042] get ehci0-controller wakeup-source is fail.
[    0.685014] sunxi ehci0-controller don't init wakeup source
[    0.691335] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xc0b5e2b0, 0x:c8885000, irq_no:38
[    0.703356] [sunxi-ehci0]: Not init ehci0
[    0.708191] get ohci0-controller wakeup-source is fail.
[    0.714158] sunxi ohci0-controller don't init wakeup source
[    0.720441] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xc0b5e540
[    0.730124] [sunxi-ohci0]: Not init ohci0
[    0.734944] get ehci1-controller wakeup-source is fail.
[    0.740908] sunxi ehci1-controller don't init wakeup source
[    0.747206] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xc0b5e7d0, 0x:c88a1000, irq_no:3a
[    0.759426] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator
[    0.798311] get ohci1-controller wakeup-source is fail.
[    0.804320] sunxi ohci1-controller don't init wakeup source
[    0.810601] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xc0b5ea60
[    0.820515] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator
[    0.902814] sun8iw20-pinctrl 2000000.pinctrl: pin PB6 already requested by 2500c00.uart; cannot claim for 2000000.pinctrl:38
[    0.915482] sun8iw20-pinctrl 2000000.pinctrl: pin-38 (2000000.pinctrl:38) status -22
[    0.926396] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    0.926755] clk: Not disabling unused clocks
[    0.940902] alloc_fd: slot 0 not NULL!
[    0.945472] VFS: Cannot open root device "mmcblk0p5" or unknown-block(0,0): error -6
[    0.954185] Please append a correct "root=" boot option; here are the available partitions:
[    0.963570] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    0.972845] CPU0: stopping
[    0.975883] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.61 #96
[    0.982617] Hardware name: Generic DT based system
[    0.988010] [<c010de4c>] (unwind_backtrace) from [<c010a5f4>] (show_stack+0x10/0x14)
[    0.996703] [<c010a5f4>] (show_stack) from [<c067cf68>] (dump_stack+0x88/0xa4)
[    1.004810] [<c067cf68>] (dump_stack) from [<c010c234>] (handle_IPI+0xe4/0x180)
[    1.013015] [<c010c234>] (handle_IPI) from [<c0341594>] (gic_handle_irq+0x70/0x78)
[    1.021511] [<c0341594>] (gic_handle_irq) from [<c01021cc>] (__irq_svc+0x6c/0xa8)
[    1.029903] Exception stack(0xc0a01f40 to 0xc0a01f88)
[    1.035572] 1f40: 000004a8 c76b9334 00000000 c0114740 00000001 c0a00000 c0a03de8 c0a03e24
[    1.044748] 1f60: c0a43000 c77ff600 c09280c0 00000000 c0b497d0 c0a01f90 c0107f48 c0107f38
[    1.053919] 1f80: 60000113 ffffffff
[    1.057836] [<c01021cc>] (__irq_svc) from [<c0107f38>] (arch_cpu_idle+0x1c/0x38)
[    1.066139] [<c0107f38>] (arch_cpu_idle) from [<c013d3dc>] (do_idle+0xd4/0x128)
[    1.074342] [<c013d3dc>] (do_idle) from [<c013d6c8>] (cpu_startup_entry+0x18/0x20)
[    1.082840] [<c013d6c8>] (cpu_startup_entry) from [<c0900c74>] (start_kernel+0x358/0x3e8)
[    1.092018] [<c0900c74>] (start_kernel) from [<00000000>] (0x0)
[    1.098664] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---

qinhao4832

自己做的板：
spi上也挂了一个nand。
实际构建系统的是TF卡启动。每次按复位键后，能启动成功。
板子上电完全没反应，控制台没输出，按复位键后可以正常启动。

大佬们，请教一下这个问题，我应该检查什么方向？

qinhao4832

@qinlinbin 实测可以解决问题。多谢

qinhao4832

我改了以后，初始化i2c1的时候，不再提示PG9错误。但是实际通讯的时候 PG9 没有波形。楼主改了以后，I2C1正常了吗？

SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
		SUNXI_FUNCTION(0x0, "gpio_in"),
		SUNXI_FUNCTION(0x1, "gpio_out"),
		SUNXI_FUNCTION(0x2, "uart1"),		/* CTS */
		SUNXI_FUNCTION(0x3, "twi1"),		/* SDA */
		SUNXI_FUNCTION(0x4, "gmac0"),		/* RXD3/NULL */
		SUNXI_FUNCTION(0x5, "uart3"),		/* RX */
		SUNXI_FUNCTION_IRQ_BANK(0xE, 5, 9),
		SUNXI_FUNCTION(0xF, "io_disabled")),

qinhao4832

@whycan 晕哥，这颗挺多人用的。请问这个都怎么解决？是有更新的驱动吗？还是用 tslib滤波？我已经试了tslib滤波几种参数组合了没什么效果。

qinhao4832

ns2009 接4线7寸电阻触摸屏。平台是 V3S TINA3.5。使用tslib 校准后，ts_test 发现总是飞点，手压力不同时，得到的坐标不一样。尤其是屏边缘飞得很厉害。做过这些测试工作：
1，试过脚位兼容的tsc2007 ns2009，没什么改善。
2，试过换2块触摸屏，没什么改善。
3，tslib 开了几种滤波，改善很小。

请教大家，还有啥办法可以再试试？

qinhao4832

@whycan 中断次数没有增加。硬件确定没问题，有脉冲。之前用其他驱动，轮训这个IO，是可以驱动用起来的。现在想正常用中断去做，发现中断向量与uart0 重复，不知道是不是这个原因，导致中断进不去。

qinhao4832

@whycan 次数没有增加

qinhao4832

@whycan PG0 192

qinhao4832

平台是：V3S Tina3.5 tsc2007.c
问题：驱动加载成功。中断申请成功，但是中断没反应，查看中断号。发现中断号与串口uart0 中断号是重复的，都是32。

这是启动的日志。 gpio 转 irq 出来是55中断号。 55 放到devm_request_threaded_irq 去申请中断，成功申请成功，但是中断不响应。

[    4.055787] ============ pin 193 for TSC2007_power==============
[    4.063039] tsc2007 0-0048: x= 0 y=0 z=0
[    4.067400] tsc2007 0-0048: poll_period= 1)
[    4.072460] tsc2007 0-0048: ti,x-plate-ohms = 660)
[    4.084670] tsc2007 0-0048: =========== ts->gpio 192 ==============
[    4.101097] tsc2007 0-0048: test_irq, 55
[    4.105492] tsc2007 0-0048: &client->dev c0cb2660, irq 56 name :tsc2007
[    4.116767] input: TSC2007 Touchscreen as /devices/platform/soc/twi0/i2c-0/0-0048/input/input1

展示所有中断，32这个中断向量是重复的：

17:       5731     GIC-0  29 Level     arch_timer
18:          0     GIC-0  30 Level     arch_timer
55:          0  sunxi_pio_edge  32 Edge      tsc2007
87:      10104     GIC-0  82 Level     1c02000.dma-controller
90:         68     GIC-0  32 Level     uart0
93:         14     GIC-0  38 Level     twi0
94:          0     GIC-0  90 Level     cedar_dev
95:       9778     GIC-0 118 Level     dispaly
97:        119     GIC-0 103 Level     sunxi_usb_udc
100:          0     GIC-0  62 Level     sunxikbd
102:          0     GIC-0 117 Level     vfe_cci

qinhao4832

@whycanservice 应该不是好像全是识别成坏块。spinand 都换了3颗了，都是一样的现象。

qinhao4832

使用F1C200S TINA3.5 SPINAND 在windows下的PhoenixSuit V1.19烧写固件卡在7%。最终提示失败。

已经有按照tina的文档，修改sys_config.fex，make menuconfig，make kernel_menuconfig。

环境是：
SPINAN型号：W25N01G
tina3.5
u-boot-2014.07
linux-3.10

以下是烧录的时候，日志的头尾两端。

[0]beign to init dram
[23]init dram ok


U-Boot 2014.07 (Jul 31 2018 - 14:59:19) Allwinner Technology

uboot commit : 6604446f7bddb8fe53f2b993100929f92a5f4d6e

i2c_init: by cpux
[I2C-DEBUG]:i2c_set_clock() 354
[I2C-ERROR]:twi_send_clk_9pulse() 136 SDA is still Stuck Low, failed.
i2c_init ok
[2.642]pmbus:   ready
axp: get node[/soc/pmu0] error
axp_probe error
[2.649]PMU: cpux 408 Mhz,AXI=408 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz
DRAM:  32 MiB
[2.658]fdt addr: 0x809e77a0
[2.660]gd->fdt_size: 0xc360
Relocation Offset is: 01524000
axp: get node[/soc/pmu0] error
int sunxi_dma_init---
irq enable
[2.730]flash init start
workmode = 16,storage type = 3
try card 1
[2.736][mmc]: mmc driver ver 2018-6-1 17:39:00
SUNXI SD/MMC: 1
[2.753][mmc]: ************Try SD card 1************
[mmc]: mmc 1 cmd 8 timeout, err 100
[mmc]: smc 1 err, cmd 8,  RTO
[mmc]: mmc 1 close bus gating and reset
[mmc]: mmc 1 mmc cmd 8 err 0x00000100
[2.771][mmc]: mmc send if cond failed
[mmc]: mmc 1 cmd 55 timeout, err 100
[mmc]: smc 1 err, cmd 55,  RTO
[mmc]: mmc 1 close bus gating and reset
[mmc]: mmc 1 mmc cmd 55 err 0x00000100
[2.789][mmc]: send app cmd failed
[2.792][mmc]: ************Try MMC card 1************
[mmc]: mmc 1 cmd 1 timeout, err 100
[mmc]: smc 1 err, cmd 1,  RTO
[mmc]: mmc 1 close bus gating and reset
[mmc]: mmc 1 mmc cmd 1 err 0x00000100
[2.814][mmc]: read op condition failed
[2.817][mmc]: mmc send op cond failed
Card did not respond to voltage select!
[2.824][mmc]: ************SD/MMC 1 init error!!!************
[2.830][mmc]: mmc_init_boot: mmc int fail
[2.833][mmc]: mmc_init: mmc init fail, err -17
MMC init failed
try emmc fail
[2.840]NAND_UbootProbe start...
[2.843]NB1 : enter phy init
[2.846]nand_physic_init
[2.850]nand0: get node offset error
[2.853]init nctri NAND PIORequest error!
[2.857]nand_physic_init, init nctri error
[2.861]nand_physic_init init_parameter error
[2.865]nand_physic_init error -1
[2.868]SpiNandHwInit: Start Nand Hardware initializing Jun  9 2018 19:05:34.....
[2.875]uboot: nand version: 3 6008 20180610 1300
[2.892]request spi gpio  ok!
int sunxi_dma_init---
irq enable
[2.897]uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x81db8c7c
[2.905]request general tx dma channel ok!
[2.908]uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x81db8c9c
[2.916]request general rx dma channel ok!
[2.920]SPI nand ID: 21aaef 0
[2.922][SCAN_DBG] NandTwoPlaneOp: 1, DriverTwoPlaneOPCfg: 1, 0xffbfffff
[2.929]nand : get id number_ctl from script:0x55aaaa55
[2.934]_UpdateExtAccessFreqPara: no para.
[2.938]PHY_Scan_DelayMode: right delay mode 0x0
[2.942]PHY_Scan_DelayMode: right delay mode 0x800
_get_spic_clk_v1: sclk0=0x64
[2.949]PHY_Scan_DelayMode: right delay mode,clk 50 MHz, SPI_TCR = 0x00000984, bit[13]=0,bit[11]=1
[2.958]physic_info_read start!!
[2.961]physic_info_get_offset start!!
[2.966]physic_info_get_one_copy start!!
[2.970]block 13 page 48
[2.972]block 13 page 49
[2.974]block 13 page 50
[2.977]block 13 page 51
[2.979]block 13 page 52
[2.981]block 13 page 53
[2.983]block 13 page 54
[2.986]block 13 page 55
[2.988]block 13 page 56
[2.990]block 13 page 57
[2.992]block 13 page 58
[2.994]block 13 page 59
[2.997]block 13 page 60
[2.999]block 13 page 61
[3.001]block 13 page 62
[3.003]block 13 page 63
[3.006]physic info copy is ok
[3.009]

[3.010][SCAN_DBG] ==============Nand Architecture Parameter==============
[3.016][SCAN_DBG]    Nand Chip ID:         0xff21aaef 0xffffffff
[3.022][SCAN_DBG]    Nand Chip Count:      0x1
[3.026][SCAN_DBG]    Nand Chip Connect:    0x1
[3.030][SCAN_DBG]    Sector Count Of Page: 0x4
[3.035][SCAN_DBG]    Page Count Of Block:  0x40
[3.039][SCAN_DBG]    Block Count Of Die:   0x400
[3.043][SCAN_DBG]    Plane Count Of Die:   0x1
[3.048][SCAN_DBG]    Die Count Of Chip:    0x1
[3.052][SCAN_DBG]    Bank Count Of Chip:   0x1
[3.056][SCAN_DBG]    Optional Operation:   0x60
[3.060][SCAN_DBG]    Access Frequence:     0x0
[3.065][SCAN_DBG] =======================================================

[3.092]secure storage updata ok!
[3.095]nand secure storage ok: 58,59
[3.099]NB1 : nand phy init ok
[3.101]NB1 : enter phy Exit
nand release dma:81db8c7c
nand release dma:0
sunxi dma exit
[3.109]NAND_UbootProbe end: 0x0
nand found
read mbr copy[0] failed
read mbr copy[1] failed
read mbr copy[2] failed
read mbr copy[3] failed
[3.122]flash init end
[3.124]try to burn key
[3.129]inter uboot shell
Hit any key to stop autoboot:  0
work mode=0x10
run usb efex
delay time 2500
int sunxi_dma_init---
irq enable
sunxi_dma_install_int ok
usb init ok
set address 0xd
set address 0xd
SUNXI_EFEX_ERASE_TAG
erase_flag = 0x0
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
the 0 mbr table is ok
the 1 mbr table is ok
the 2 mbr table is ok
the 3 mbr table is ok
*************MBR DUMP***************
total mbr part 8

part[0] name      :bootlogo
part[0] classname :DISK
part[0] addrlo    :0x2000
part[0] lenlo     :0x800
part[0] user_type :32768
part[0] keydata   :0
part[0] ro        :0

part[1] name      :env
part[1] classname :DISK
part[1] addrlo    :0x2800
part[1] lenlo     :0x200
part[1] user_type :32768
part[1] keydata   :0
part[1] ro        :0

part[2] name      :boot
part[2] classname :DISK
part[2] addrlo    :0x2a00
part[2] lenlo     :0x3000
part[2] user_type :32768
part[2] keydata   :0
part[2] ro        :0

part[3] name      :rootfs
part[3] classname :DISK
part[3] addrlo    :0x5a00
part[3] lenlo     :0x15c70
part[3] user_type :32768
part[3] keydata   :0
part[3] ro        :0

part[4] name      :rootfs_data
part[4] classname :DISK
part[4] addrlo    :0x1b670
part[4] lenlo     :0xc800
part[4] user_type :32768
part[4] keydata   :0
part[4] ro        :0

part[5] name      :misc
part[5] classname :DISK
part[5] addrlo    :0x27e70
part[5] lenlo     :0x200
part[5] user_type :32768
part[5] keydata   :0
part[5] ro        :0

part[6] name      :private
part[6] classname :DISK
part[6] addrlo    :0x28070
part[6] lenlo     :0x200
part[6] user_type :32768
part[6] keydata   :0
part[6] ro        :0

part[7] name      :UDISK
part[7] classname :DISK
part[7] addrlo    :0x28270
part[7] lenlo     :0x0
part[7] user_type :33024
part[7] keydata   :0
part[7] ro        :0

total part: 9
mbr 0, 2000, 8000
bootlogo 1, 800, 8000
env 2, 200, 8000
boot 3, 3000, 8000
rootfs 4, 15c70, 8000
rootfs_data 5, c800, 8000
misc 6, 200, 8000
private 7, 200, 8000
UDISK 8, 0, 8100
[7.326]erase_flag = 0
[7.328]NB1 : enter phy init
[7.330]SpiNandHwInit: Start Nand Hardware initializing Jun  9 2018 19:05:34.....
[7.337]uboot: nand version: 3 6008 20180610 1300
[7.354]request spi gpio  ok!
[7.357]uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x81db8c9c
[7.364]request general tx dma channel ok!
[7.368]uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x81db8cbc
[7.375]request general rx dma channel ok!
[7.379]SPI nand ID: 21aaef 0
[7.382][SCAN_DBG] NandTwoPlaneOp: 1, DriverTwoPlaneOPCfg: 1, 0xffbfffff
[7.388]nand : get id number_ctl from script:0x55aaaa55
[7.393]_UpdateExtAccessFreqPara: no para.
[7.397]PHY_Scan_DelayMode: right delay mode 0x0
[7.402]PHY_Scan_DelayMode: right delay mode 0x800
_get_spic_clk_v1: sclk0=0x64
[7.409]PHY_Scan_DelayMode: right delay mode,clk 50 MHz, SPI_TCR = 0x00000984, bit[13]=0,bit[11]=1
[7.417]physic_info_read start!!
[7.420]physic_info_read already!!
[7.423]

[7.424][SCAN_DBG] ==============Nand Architecture Parameter==============
[7.431][SCAN_DBG]    Nand Chip ID:         0xff21aaef 0xffffffff
[7.437][SCAN_DBG]    Nand Chip Count:      0x1
[7.441][SCAN_DBG]    Nand Chip Connect:    0x1
[7.445][SCAN_DBG]    Sector Count Of Page: 0x4
[7.449][SCAN_DBG]    Page Count Of Block:  0x40
[7.454][SCAN_DBG]    Block Count Of Die:   0x400
[7.458][SCAN_DBG]    Plane Count Of Die:   0x1
[7.462][SCAN_DBG]    Die Count Of Chip:    0x1
[7.466][SCAN_DBG]    Bank Count Of Chip:   0x1
[7.471][SCAN_DBG]    Optional Operation:   0x60
[7.475][SCAN_DBG]    Access Frequence:     0x0
[7.479][SCAN_DBG] =======================================================

[7.507]secure storage updata ok!
[7.510]nand secure storage ok: 58,59
[7.513]NB1 : nand phy init ok
[7.516]uboot_start_block 8 uboot_next_block 58.
[7.520]check nand version start.
[7.523]Current nand driver version is ff 0 3 1
[7.528]Media version is valid in block 8, version info is ff 0 3 1
[7.534]nand driver version match ok in block 8.
[7.538]nand version = 0
[7.540]has cleared the boot blocks.
[7.548]NAND_Uboot_Erase
[7.550]NB1 : enter phy Exit
nand release dma:81db8c9c
nand release dma:0
not need erase flash
sunxi_sprite_erase_flash, erase_flag=0
private part exist
NAND_UbootInit
[7.565]NAND_UbootInit start
[7.567]NB1: enter NAND_LogicInit
[7.570]SpiNandHwInit: Start Nand Hardware initializing Jun  9 2018 19:05:34.....
[7.578]uboot: nand version: 3 6008 20180610 1300
[7.594]uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x81db8c9c
[7.602]uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x81db8cbc
_get_spic_clk_v1: sclk0=0x64
[7.633]not burn nand partition table!
[7.637][ND]not enough block:479,878!!
[7.640][NE]build phy partition 0 error!
[7.644][NE]build all phy partition fail!
[7.764][NE]not find mbr table!!!!
[7.767]NB1: nand_info_init fail
[7.770]NAND_UbootInit end: 0xfffffffb
NAND_UbootExit

[19.204]PHY_PageReadSpare bad flag: bank 0x0  block 0x3f8  page 0x0
[19.210][PHY_DBG] Find a bad block (NO. 0x3f8) in the Die 0x0
[19.216]PHY_PageReadSpare bad flag: bank 0x0  block 0x3f9  page 0x0
[19.222][PHY_DBG] Find a bad block (NO. 0x3f9) in the Die 0x0
[19.227]PHY_PageReadSpare bad flag: bank 0x0  block 0x3fa  page 0x0
[19.233][PHY_DBG] Find a bad block (NO. 0x3fa) in the Die 0x0
[19.239]PHY_PageReadSpare bad flag: bank 0x0  block 0x3fb  page 0x0
[19.245][PHY_DBG] Find a bad block (NO. 0x3fb) in the Die 0x0
[19.251]PHY_PageReadSpare bad flag: bank 0x0  block 0x3fc  page 0x0
[19.257][PHY_DBG] Find a bad block (NO. 0x3fc) in the Die 0x0
[19.262]PHY_PageReadSpare bad flag: bank 0x0  block 0x3fd  page 0x0
[19.268][PHY_DBG] Find a bad block (NO. 0x3fd) in the Die 0x0
[19.274]PHY_PageReadSpare bad flag: bank 0x0  block 0x3fe  page 0x0
[19.280][PHY_DBG] Find a bad block (NO. 0x3fe) in the Die 0x0
[19.286]PHY_PageReadSpare bad flag: bank 0x0  block 0x3ff  page 0x0
[19.292][PHY_DBG] Find a bad block (NO. 0x3ff) in the Die 0x0
[19.297][NE]not find mbr table!!!!
[19.301]NB1: nand_info_init fail
[19.304]NAND_UbootInit end: 0xfffffffb
sunxi sprite init fail when downlaod mbr

qinhao4832

@whycan 是的。勾上就可以了。多谢

qinhao4832

大佬坛友们请帮忙看看：
F1C200s tina3.5 想要启用adb，参考论坛内的帖子操作，运行脚本找不到g_ffs.ko

mount: mounting adb on /dev/usb-ffs/adb failed: No such device
root@billQin:/# -/bin/sh: adbd: not found

请问这个路径填哪里？

make modules_install INSTALL_MOD_PATH=

或是有什么其他方法？有文档资料吗？

qinhao4832 发布的帖子