Orange pi zero2 H616 从emmc启动出现以下错误
-
编译了H616 tina-linux sdk，生产镜像成功。烧录emmc卡成功后，系统启动遇到以下问题，请各位解答这是什么错误。
[37]HELLO! BOOT0 is starting! [40]BOOT0 commit : 3ae35eb [43]set pll start [45]periph0 has been enabled [48]set pll end [50]unknow PMU [52]PMU: AXP806 [59]dram para16 invalid use default para [63]vaild para:1 select dram para0 [66]board init ok [68]DRAM BOOT DRIVE INFO: V0.648 [71]the chip id is 0x5000 [74]chip id check OK [76]DRAM_VCC set to 1500 mv [82]read_calibration error [87]read_calibration error [93]read_calibration error [99]read_calibration error [104]read_calibration error [110]read_calibration error [116]read_calibration error [122]read_calibration error [127]read_calibration error [133]read_calibration error [136]retraining final error [142][AUTO DEBUG]32bit,1 ranks training success! [154]DRAM CLK =720 MHZ [156]DRAM Type =3 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4) [164]Actual DRAM SIZE =1024 M [167]DRAM SIZE =1024 MBytes, para1 = 30fa, para2 = 4000000, dram_tpr13 = 6041 [180]DRAM simple test OK. [182]rtc standby flag is 0x0, super standby flag is 0x0 [188]dram size =1024 [191]card no is 0 [192]sdcard 0 line count 4 [195][mmc]: mmc driver ver 2021-10-12 13:56 [199][mmc]: b mmc 0 bias 0 [207][mmc]: Wrong media type 0x0 [210][mmc]: ***Try SD card 0*** [221][mmc]: HSSDR52/SDR25 4 bit [224][mmc]: 50000000 Hz [226][mmc]: 29818 MB [228][mmc]: ***SD/MMC 0 init OK!!!*** [328]Loading boot-pkg Succeed(index=0). [331][mmc]: b mmc 0 bias 0 [334]Entry_name = u-boot [343]Entry_name = monitor [347]Entry_name = dtbo [350]Entry_name = dtb [353]Jump to second Boot. NOTICE: BL3-1: v1.0(debug):05d6c57 NOTICE: BL3-1: Built : 13:35:35, 2021-10-28 NOTICE: BL3-1 commit: 8 NOTICE: cpuidle init version V1.0 ERROR: Error initializing runtime service tspd_fast NOTICE: BL3-1: Preparing for EL3 exit to normal world NOTICE: BL3-1: Next image address = 0x4a000000 ?OTICE: BL3-1: Next image spsr = 0x1d3 U-Boot 2018.05-g768449b (Apr 14 2023 - 15:44:12 +0800) Allwinner Technology [00.398]CPU: Allwinner Family [00.401]Model: sun50iw9 I2C: ready [00.406]DRAM: 1 GiB [00.408]Relocation Offset is: 35ebf000 [00.444]secure enable bit: 0 [00.448]pmu_axp152_probe pmic_bus_read fail [00.452]PMU: AXP806 [00.453]PMU: pmu_axp806 found [00.459]dcdcc_vol = 960, onoff=1 [00.462]aldo1_vol = 3300, onoff=1 [00.465]bldo1_vol = 1800, onoff=1 [00.469]dcdcd_vol = 1340, onoff=1 [00.472]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=400Mhz [00.479]init_clocks:finish [00.481]drv_disp_init [00.507]HDMI 2.0 driver init start! [00.515]__clk_enable: clk is null. [00.518]hdmi cec clk enable failed! [00.524]drv_disp_init finish [00.527]gic: sec monitor mode [00.529]sunxi flash type@1 not support fast burn key [00.535]boot_gui_init:start tcon_de_attach:de=0,tcon=2[00.542][HDMI2.0]CEA VIC=16: [00.545]1920x1080p[00.546]@60 Hz [00.548]16:9, [00.549]8-bpp [00.550]YCbCr-444 [00.552]BT709 [00.553]eotf:SDR_LUMINANCE_RANGE [00.669]switch device: sel=0, type=4, mode=10, format=1, bits=0, eotf=4, cs=257 [00.676]boot_gui_init:finish [00.679]flash init start [00.681]workmode = 17,storage type = 1 try card 2 set card number 2 get card number 2 [00.689][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.695][mmc]: get sdc_type fail and use default host:tm4. [00.706][mmc]: Is not Boot mode! [00.709][mmc]: SUNXI SDMMC Controller Version:0x40502 [00.720][mmc]: ************Try SD card 2************ [00.725][mmc]: mmc 2 cmd timeout 100 status 100 [00.729][mmc]: smc 2 err, cmd 8, RTO [00.733][mmc]: mmc 2 close bus gating and reset [00.738][mmc]: mmc 2 cmd timeout 100 status 100 [00.742][mmc]: smc 2 err, cmd 55, RTO [00.745][mmc]: mmc 2 close bus gating and reset [00.750][mmc]: ************Try MMC card 2************ [00.758][mmc]: mmc 2 cmd timeout 100 status 100 [00.762][mmc]: smc 2 err, cmd 1, RTO [00.766][mmc]: mmc 2 close bus gating and reset [00.770][mmc]: Card did not respond to voltage select! [00.775][mmc]: ************SD/MMC 2 init error!************ [00.780][mmc]: mmc init product failed MMC init failed try emmc fail nand common1 version: v1.17 2021-02-22 16:10 [00.790]NB1 : enter phy init [00.793][NI]enter rawnand hardward init.. [00.804][NE]rawnand not support chip 0: 06 06 06 06 06 06 06 06 [00.809][NE]rawnand not support chip 1: 06 06 06 06 06 06 06 06 [00.815][NE]rawnand not support chip 2: 06 06 06 06 06 06 06 06 [00.821][NE]rawnand not support chip 3: 06 06 06 06 06 06 06 06 [00.826][NE]no rawnand found! [00.829][NE]rawnand_channel_init channel@0 chips init fail [00.834][NI]rawnand hardward init fail [00.838][NI]---rawnand_dump_clock start--- [00.841][NI]SUNXI_CCM_BASE: 0x03001000 [00.845][NI]nand0 clk: 8300010e [00.848][NI]nand1 clk: 8300010e [00.851][NI]nand bus gating reset: 10001 [00.854][NI]mbus cfg: c1000002 [00.857][NI]mbus master clk gating: 25 [00.861][NI]pll_peri0 ctrl: b8003100 [00.864][NI]pll_peri1 ctrl: 88003100 [00.867][NI]---rawnand_dump_clock end--- [00.871][NI]---rawnand_dump_gpio_nand start--- [00.875][NI]SUNXI_PIO_BASE: 0x0300b000 [00.878][NI]pc cfg0: 22222222 [00.881][NI]pc cfg1: 22222222 [00.884][NI]pc cfg2 2 [00.886][NI]pc data: 0 [00.888][NI]pc drv0_lvl: 55555555 [00.891][NI]pc drv1_lvl: 1 [00.893][NI]pc pull_0: 40000440 [00.896][NI]pc pull_1: 1 [00.898][NI]voltage mode select: 0 [00.901][NI]---rawnand_dump_gpio_nand end--- [00.905][NE]nand_physic_init error -1 [00.909]NB1 : nand phy init fail [00.912]Failed to probe nand flash try nand fail SF: Detected mx25l1606e with page size 256 Bytes, erase size 4 KiB, total 2 MiB [00.930]MMC: 0 [00.931][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.937][mmc]: get sdc_type fail and use default host:tm1. [00.948][mmc]: Using default timing para [00.952][mmc]: SUNXI SDMMC Controller Version:0x40200 [00.970][mmc]: card_caps:0x3000000a [00.973][mmc]: host_caps:0x3000003f [00.978]Loading Environment from SUNXI_FLASH... OK [00.983]try to burn key [00.986]out of usb burn from boot: not boot mode [00.990]Net: [00.991]Net Initialization Skipped [00.994]No ethernet found. Hit any key to stop autoboot: 0 sunxi work mode=0x11 run card sprite [01.010]try sprite_led_gpio config [01.014]sprite_led_gpio start [01.017]sunxi sprite begin screen_width = 1280 screen_height = 720 bar x1: 320 y1: 320 bar x2: 960 y2: 400 ** Unable to read file font32.sft ** sunxi ui_char info error : unable to open font file font32.sft ui_char_info.word_size is 32 boot_ui_char: open font failed firmware name <NULL> img start = 0x18000 try to read mmc start 98304 read mmc ok [01.062]firmware probe ok [01.064]fetch download map *************DOWNLOAD MAP DUMP************ total download part 4 download part[0] name :bootloader download part[0] download file :BOOT-RESOURCE_FE download part[0] verify file :VBOOT-RESOURCE_F download part[0] lenlo :0x10000 download part[0] addrlo :0x8000 download part[0] encrypt :0x0 download part[0] verify :0x1 download part[1] name :env download part[1] download file :ENV_FEX000000000 download part[1] verify file :VENV_FEX00000000 download part[1] lenlo :0x8000 download part[1] addrlo :0x18000 download part[1] encrypt :0x0 download part[1] verify :0x1 download part[2] name :boot download part[2] download file :BOOT_FEX00000000 download part[2] verify file :VBOOT_FEX0000000 download part[2] lenlo :0x10000 download part[2] addrlo :0x20000 download part[2] encrypt :0x0 download part[2] verify :0x1 download part[3] name :rootfs download part[3] download file :ROOTFS_FEX000000 download part[3] verify file :VROOTFS_FEX00000 download part[3] lenlo :0x40000 download part[3] addrlo :0x30000 download part[3] encrypt :0x0 download part[3] verify :0x1 [01.176]fetch mbr sunxi sprite error : buffer is smaller than data size sunxi sprite error : read mbr failed sunxi sprite error : fetch mbr error sprite_test - do a sprite test Usage: sprite_test NULL -
-
此回复已被删除！ -
@whycan 32GB
-
补充一个信息，使用orage 提供orange pi zero2 的img可以正常启动，但自己编译全志的tina-linux启动失败。
-
@wilsonli 配置文件最好对比一下
-
@yixintai 谢谢，正在对比这里。
只是关于sys_config.fex配置等待文档较少，学习门槛比较陡峭
Copyright © 2024 深圳全志在线有限公司 粤ICP备2021084185号 粤公网安备44030502007680号