V831 的 Tina 启动没有 Uboot 与 Linux 日志输出，dmesg有输出

柚木鉉 LV 9

printk的等级已经设置7了

[302]HELLO! BOOT0 is starting!
[305]BOOT0 commit : e3b2a9e
[307]board init start
[310]set pll start
[312]set pll end
[314][pmu]: bus read error
[316][pmu]: bus read error
[319]board init ok
[321]chip id check OK
[323]DRAM BOOT DRIVE INFO: V0.41
[326]DRAM CLK = 528 MHz
[328]DRAM Type = 2 (2:DDR2,3:DDR3)
[332]DRAMC read ODT  off.
[334]DRAM ODT off.
[337]DRAM SIZE =64 M
[343]DRAM simple test OK.
[345]rtc standby flag is 0x0, super standby flag is 0x0
[350]dram size =64
MESSAGE: [0x0] TEE-CORE: OP-TEE version: sun8iw19p1_v0.6.0-14-gf6954e7 #1 2019年 11月 21日 星期四 01:34:42 UTC arm
ERROR:   [0x0] TEE-CORE:platform_standby_fdt_parse:126: no pmu node
ERROR:   [0x0] TEE-CORE:sunxi_twi_parse_from_dt:84: no pmu node
mount: mounting pstore on /sys/fs/pstore failed: No such file or directory
mount: mounting /dev/by-name/rootfs_data on /overlay failed: No such file or directory
Mount Failed: formating /dev/by-name/rootfs_data to ext4 ...
mke2fs 1.42.12 (29-Aug-2014)
The file /dev/by-name/rootfs_data does not exist and no size was specified.
can't run '/bin/mkdir': Read-only file system
mount: mounting devpts on /dev/pts failed: No such file or directory
------run rc.preboot file-----
------run rc.modules file-----
------run rc.final file-----
Load mpp modules
read-only file system detected...done
Starting network...
ifconfig: SIOCGIFFLAGS: No such device
Successfully initialized wpa_supplicant
Could not read interface wlan0 flags: No such device
nl80211: Driver does not support authentication/association or connect commands
nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Could not read interface wlan0 flags: No such device
wlan0: Failed to initialize driver interface
udhcpc: SIOCGIFINDEX: No such device
Starting telnetd: OK
enable android usb
sh: write error: Resource busy


BusyBox v1.27.2 () built-in shell (ash)

------run profile file-----
 _____  _              __     _
|_   _||_| ___  _ _   |  |   |_| ___  _ _  _ _
  | |   _ |   ||   |  |  |__ | ||   || | ||_'_|
  | |  | || | || _ |  |_____||_||_|_||___||_,_|
  |_|  |_||_|_||_|_|  Tina is Based on OpenWrt!
 ----------------------------------------------
 Tina Linux (Neptune, 5C1C9C53)
 ----------------------------------------------
root@TinaLinux:/# cat /proc/sys/kernel/printk
 7       7       1       7

柚木鉉 LV 9

使用量产卡刷入Uboot有输出，使用启动卡就不行了

[303]HELLO! BOOT0 is starting!
[306]BOOT0 commit : e3b2a9e
[309]board init start
[311]set pll start
[314]set pll end
[315][pmu]: bus read error
[318][pmu]: bus read error
[321]board init ok
[322]chip id check OK
[325]DRAM BOOT DRIVE INFO: V0.41
[328]DRAM CLK = 528 MHz
[330]DRAM Type = 2 (2:DDR2,3:DDR3)
[333]DRAMC read ODT  off.
[336]DRAM ODT off.
[338]DRAM SIZE =64 M
[344]DRAM simple test OK.
[347]rtc standby flag is 0x0, super standby flag is 0x0
[352]dram size =64
MESSAGE: [0x0] TEE-CORE: OP-TEE version: sun8iw19p1_v0.6.0-14-gf6954e7 #1 2019. 11. 21. .... 01:34:42 UTC arm
ERROR:   [0x0] TEE-CORE:platform_standby_fdt_parse:126: no pmu node
ERROR:   [0x0] TEE-CORE:sunxi_twi_parse_from_dt:84: no pmu node


U-Boot 2018.05-00008-g384031a (Jan 16 2020 - 14:12:41 +0800) Allwinner Technology

[00.467]CPU:   Allwinner Family
[00.470]Model: sun8iw19
I2C:   ready

[00.474]DRAM:  64 MiB
[00.477]Relocation Offset is: f9f46000
[00.498]secure enable bit: 0
[00.502]pmu_axp152_probe pmic_bus_read fail
[00.505]pmu_axp2101_probe pmic_bus_read fail
[00.509]PMU: no found
[00.511]bmu_axp152_probe pmic_bus_read fail
[00.515]bmu_axp2101_probe pmic_bus_read fail
[00.519]BMU: no found
[00.521]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=132Mhz
[00.528]gic: sec monitor mode
[00.530]flash init start
[00.533]workmode = 17,storage type = 1
try card 2
set card number 2
get card number 2
[00.540]mmc driver ver uboot2018:2019-12-13 9:48:00
[00.545]get mem for descripter OK !
[00.549]get gpio bias fail
[00.551]get gpio_bias: pc_bias fail
[00.555]get card2_boot_para:sdc_io_1v8 fail
[00.561]get card2 disable pin fail
[00.564]get card2_boot_para:sdc_ex_dly_used fail
[00.568]get sdc_ex_dly_used -1090671915, use auto tuning sdly
[00.574]get sdc2 sdc_boot0_sup_1v8 fail.
[00.578]get card-pwr-gpios faild
[00.581]get card2_boot_para:time_pwroff_ms:use default time_pwroff:200
[00.587]Using default timing para
[00.590]init mmc 2 clock and io
[00.593]devnum 2, prv 43fb6590, bdesc 42b664ec
[00.597]SUNXI SD/MMC: 2
[00.599]==================== work mode: 17 0, sample_mode:0
[00.605]=============== start mmc_init_boot...
[00.623]Card did not respond to voltage select!
[00.627]mmc_init: -95, time 28
[00.630]mmc_init: mmc init fail, err -95
MMC init failed
try emmc fail
[00.636]NB1 : enter phy init
[00.639][NI]enter rawnand hardward init..
[00.643]nand0: get node offset error
[00.646][NE]init nctri NAND PIORequest error!
[00.650][NE]rawnand_channel_init channel@0 init nctri fail
[00.656][NI]rawnand hardward init fail
[00.659][NI]---rawnand_dump_clock start---
[00.663][NI]---rawnand_dump_clock end---
[00.667][NI]---rawnand_dump_gpio_nand start---
[00.671][NI]---rawnand_dump_gpio_nand end---
[00.675][NE]nand_physic_init error -1
[00.678]NB1 : nand phy init fail
[00.681]Failed to probe nand flash
try nand fail
[00.691]unrecognized JEDEC id bytes: ff, ff, ff
try spinor fail
initcall sequence 43fab5dc failed at call 4a00a301 (err=-1)
### ERROR ### Please RESET the board ###



[302]HELLO! BOOT0 is starting!
[305]BOOT0 commit : e3b2a9e
[307]board init start
[310]set pll start
[312]set pll end
[314][pmu]: bus read error
[316][pmu]: bus read error
[319]board init ok
[321]chip id check OK
[323]DRAM BOOT DRIVE INFO: V0.41
[326]DRAM CLK = 528 MHz
[328]DRAM Type = 2 (2:DDR2,3:DDR3)
[332]DRAMC read ODT  off.
[334]DRAM ODT off.
[337]DRAM SIZE =64 M
[343]DRAM simple test OK.
[345]rtc standby flag is 0x0, super standby flag is 0x0
[350]dram size =64
MESSAGE: [0x0] TEE-CORE: OP-TEE version: sun8iw19p1_v0.6.0-14-gf6954e7 #1 2019. 11. 21. .... 01:34:42 UTC arm
ERROR:   [0x0] TEE-CORE:platform_standby_fdt_parse:126: no pmu node
ERROR:   [0x0] TEE-CORE:sunxi_twi_parse_from_dt:84: no pmu node
mount: mounting pstore on /sys/fs/pstore failed: No such file or directory
mount: mounting /dev/by-name/rootfs_data on /overlay failed: No such file or directory
Mount Failed: formating /dev/by-name/rootfs_data to ext4 ...
mke2fs 1.42.12 (29-Aug-2014)
The file /dev/by-name/rootfs_data does not exist and no size was specified.

can't run '/bin/mkdir': Read-only file system
mount: mounting devpts on /dev/pts failed: No such file or directory
------run rc.preboot file-----
------run rc.modules file-----
------run rc.final file-----
Load mpp modules
read-only file system detected...done
Starting network...
ifconfig: SIOCGIFFLAGS: No such device
Successfully initialized wpa_supplicant
Could not read interface wlan0 flags: No such device
nl80211: Driver does not support authentication/association or connect commands
nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Could not read interface wlan0 flags: No such device
wlan0: Failed to initialize driver interface
Starting telnetd: udhcpc: SIOCGIFINDEX: No such device
OK
enable android usb
sh: write error: Resource busy


BusyBox v1.27.2 () built-in shell (ash)

------run profile file-----
 _____  _              __     _

|_   _||_| ___  _ _   |  |   |_| ___  _ _  _ _
  | |   _ |   ||   |  |  |__ | ||   || | ||_'_|
  | |  | || | || _ |  |_____||_||_|_||___||_,_|
  |_|  |_||_|_||_|_|  Tina is Based on OpenWrt!
 ----------------------------------------------
 Tina Linux (Neptune, 5C1C9C53)
 ----------------------------------------------

柚木鉉 LV 9

修复叻，手残打开了Boot Time Optimization

#
# Boot Time Optimization
#
# CONFIG_BOOT_TIME_OPTIMIZATION is not set