D1在linux上支持RGB显示屏问题求助
-
使用tina-d1-h linux系统，想调试RGB显示屏，配置完成后，显示屏黑屏（背光是外接的所以是有背光的）
把调试信息打开，发现有报错（disp 1 not support lcd output），不知道是不是这个原因导致黑屏的。求助一下帮忙看看这是什么问题，谢谢配置：
&disp { disp_init_enable = <1>; disp_mode = <0>; screen0_output_type = <1>; screen0_output_mode = <4>; screen1_output_type = <3>; screen1_output_mode = <10>; screen1_output_format = <0>; screen1_output_bits = <0>; screen1_output_eotf = <4>; screen1_output_cs = <257>; screen1_output_dvi_hdmi = <2>; screen1_output_range = <2>; screen1_output_scan = <0>; screen1_output_aspect_ratio = <8>; dev0_output_type = <1>; dev0_output_mode = <4>; dev0_screen_id = <0>; dev0_do_hpd = <0>; dev1_output_type = <4>; dev1_output_mode = <10>; dev1_screen_id = <1>; dev1_do_hpd = <1>; def_output_dev = <0>; hdmi_mode_check = <1>; fb0_format = <0>; fb0_width = <0>; fb0_height = <0>; fb1_format = <0>; fb1_width = <0>; fb1_height = <0>; chn_cfg_mode = <1>; disp_para_zone = <1>; /*VCC-LCD*/ /* dc1sw-supply = <®_dc1sw>;*/ /*VCC-DSI*/ /* eldo3-supply = <®_eldo3>;*/ /*VCC-PD*/ /* dcdc1-supply = <®_dcdc1>;*/ }; &lcd0 { lcd_used = <1>; lcd_driver_name = "default_panel"; lcd_if = <0>; lcd_hv_if = <0>; lcd_x = <800>; lcd_y = <480>; lcd_width = <108>; lcd_height = <65>; lcd_dclk_freq = <25>; lcd_hbp = <12>; lcd_ht = <816>; lcd_hspw = <4>; lcd_vbp = <12>; lcd_vt = <496>; lcd_vspw = <4>; lcd_frm = <1>; lcd_hv_clk_phase = <0>; lcd_hv_sync_polarity= <0>; lcd_io_phase = <0x0000>; lcd_gamma_en = <0>; lcd_bright_curve_en = <0>; lcd_power = "vcc-lcd"; lcd_pin_power = "vcc-pd"; pinctrl-0 = <&rgb18_pins_a>; pinctrl-1 = <&rgb18_pins_b>; };启动信息：
[214]HELLO! BOOT0 is starting! [217]BOOT0 commit : 88480af [219]set pll start [221]fix vccio detect value:0xc0 [224]periph0 has been enabled [227]set pll end [229][pmu]: bus read error [231]board init ok [233]get_pmu_exist() = -1 [236]ddr_efuse_type: 0x0 [238]trefi:7.8ms [240][AUTO DEBUG] single rank and full DQ! [244]ddr_efuse_type: 0x0 [247]trefi:7.8ms [249][AUTO DEBUG] rank 0 row = 15 [252][AUTO DEBUG] rank 0 bank = 8 [255][AUTO DEBUG] rank 0 page size = 2 KB [259]DRAM BOOT DRIVE INFO: V0.33 [262]DRAM CLK = 792 MHz [265]DRAM Type = 3 (2:DDR2,3:DDR3) [268]DRAMC ZQ value: 0x7b7bfb [271]DRAM ODT value: 0x42. [273]ddr_efuse_type: 0x0 [276]DRAM SIZE =512 M [278]dram_tpr4:0x0 [280]PLL_DDR_CTRL_REG:0xf8004100 [283]DRAM_CLK_REG:0xc0000000 [286][TIMING DEBUG] MR2= 0x18 [290]DRAM simple test OK. [292]dram size =512 [294]card no is 0 [296]sdcard 0 line count 4 [298][mmc]: mmc driver ver 2021-04-2 16:45 [308][mmc]: Wrong media type 0x0 [311][mmc]: ***Try SD card 0*** [331][mmc]: HSSDR52/SDR25 4 bit [334][mmc]: 50000000 Hz [336][mmc]: 30436 MB [338][mmc]: ***SD/MMC 0 init OK!!!*** [388]Loading boot-pkg Succeed(index=0). [391]Entry_name = opensbi [395]Entry_name = u-boot [398]Entry_name = dtb [401]mmc not para [402]Jump to second Boot. OpenSBI auto-t113-linux-V0.8-2-g053d088 ____ _____ ____ _____ / __ \ / ____| _ \_ _| | | | |_ __ ___ _ __ | (___ | |_) || | | | | | '_ \ / _ \ '_ \ \___ \| _ < | | | |__| | |_) | __/ | | |____) | |_) || |_ \____/| .__/ \___|_| |_|_____/|____/_____| | | |_| Platform Name : T-HEAD Xuantie Platform Platform HART Features : RV64ACDFIMSUVX Platform Max HARTs : 1 Current Hart : 0 Firmware Base : 0x41fc0400 Firmware Size : 75 KB Runtime SBI Version : 0.2 MIDELEG : 0x0000000000000222 MEDELEG : 0x000000000000b1ff PMP0 : 0x0000000041fc0000-0x0000000041fdffff (A) PMP1 : 0x0000000040000000-0x000000007fffffff (A,R,W,X) PMP2 : 0x0000000080000000-0x00000000bfffffff (A,R,W,X) PMP3 : 0x0000000000020000-0x0000000000027fff (A, U-Boot 2018.05-g24521d6 (Feb 11 2022 - 08:52:39 +0000) Allwinner Technology [00.488]DRAM: 512 MiB [00.490]Relocation Offset is: 1dee7000 [00.494]secure enable bit: 0 [00.497]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz [00.503]flash init start [00.505]workmode = 0,storage type = 1 [00.508][mmc]: mmc driver ver uboot2018:2021-11-19 15:38:00 [00.514][mmc]: get sdc_type fail and use default host:tm1. [00.520][mmc]: can't find node "mmc0",will add new node [00.525][mmc]: fdt err returned <no error> [00.529][mmc]: Using default timing para [00.532][mmc]: SUNXI SDMMC Controller Version:0x50310 [00.559][mmc]: card_caps:0x3000000a [00.562][mmc]: host_caps:0x3000003f [00.567]sunxi flash init ok [00.570]line:703 init_clocks [00.573]drv_disp_init [00.584]drv_disp_init finish [00.587]boot_gui_init:start [00.590]set disp.dev2_output_type fail. using defval=0 [00.595]LCD open finish [00.597]boot_gui_init:finish partno erro : can't find partition bootloader 54 bytes read in 1 ms (52.7 KiB/s) [00.616]bmp_name=bootlogo.bmp size 3072054 3072054 bytes read in 129 ms (22.7 MiB/s) no support big size bmp[800x1280] on fb[800x480] [00.758]show bmp on fb failed !-1 [00.770]Loading Environment from SUNXI_FLASH... OK [00.790]out of usb burn from boot: not need burn key [00.816]Item0 (Map) magic is bad [00.819]the secure storage item0 copy0 magic is bad [00.845]Item0 (Map) magic is bad [00.848]the secure storage item0 copy1 magic is bad [00.852]Item0 (Map) magic is bad partno erro : can't find partition private root_partition is rootfs set root to /dev/mmcblk0p5 [00.865]update part info [00.868]update bootcmd [00.871]change working_fdt 0x5eaa6da0 to 0x5ea86da0 disable nand error: FDT_ERR_BADPATH No reserved memory region found in source FDT [00.900]update dts noncached_alloc(): addr = 0x5eb12b40 noncached_alloc(): addr = 0x5eb12b80 noncached_alloc(): addr = 0x5ec8a040 noncached_alloc(): addr = 0x5ec8a880 phy_mode=rgmii, phy_interface=7 gmac: *** using ephy_clk *** eth0 Warning: eth0 (eth0) using random MAC address - c2:f2:aa:b9:99:b2 Hit any key to stop autoboot: 0 dsp0:gpio init config fail dsp0:sharespace config fail dsp0 version is r528-tina-v1.0.0-release-37-g735b6b4-dirty DSP0 start ok, img length 254860, booting from 0x400660 [04.194]no vendor_boot partition is found Android's image name: d1-h-nezha Detect comp gzip [04.447] Starting kernel ... [04.450][mmc]: MMC Device 2 not found [04.453][mmc]: mmc 2 not find, so not exit ** 531 printk messages dropped ** [ 0.207704] of_property_read_u32_array lcd0.lcd_hv_syuv_seq fail [ 0.207925] [DISP] disp_sys_script_get_item,line:214: [ 0.207930] of_property_read_u32_array lcd0.lcd_hv_syuv_fdly fail [ 0.208350] [DISP] disp_sys_script_get_item,line:214: [ 0.208355] of_property_read_u32_array lcd0.lcd_cmap_en fail [ 0.208558] [DISP] disp_sys_script_get_item,line:214: [ 0.208563] of_property_read_u32_array lcd0.lcd_xtal_freq fail [ 0.208786] [DISP] disp_sys_script_get_item,line:222: [ 0.208791] of_property_read_string lcd0.lcd_size fail [ 0.209006] [DISP] disp_sys_script_get_item,line:222: [ 0.209010] of_property_read_string lcd0.lcd_model_name fail [ 0.209218] [DISP] lcd_clk_init,line:493: [ 0.209221] lcd 0 clk init [ 0.209463] [DISP] disp_init_hdmi,line:1052: [ 0.209467] disp_init_hdmi [ 0.209490] [DISP] disp_init_mgr,line:2933: [ 0.209494] disp_init_mgr [ 0.209507] [DISP] disp_init_mgr,line:2968: [ 0.209512] mgr 0, 0x(____ptrval____) [ 0.209526] [DISP] disp_init_mgr,line:2968: [ 0.209529] mgr 1, 0x(____ptrval____) [ 0.209541] [DISP] disp_init_lyr,line:758: [ 0.209543] disp_init_lyr [ 0.209584] [DISP] disp_init_enhance,line:701: [ 0.209587] disp_init_enhance [ 0.209599] [DISP] disp_init_smbl,line:396: [ 0.209601] disp_init_smbl [ 0.209619] [DISP] disp_init_connections,line:447: [ 0.209622] disp_init_connections [ 0.209632] [DISP] disp_get_layer_1,line:136: [ 0.209636] disp0 layer0: 0,0,0 [ 0.209645] [DISP] disp_get_layer_1,line:136: [ 0.209649] disp0 layer1: 0,0,1 [ 0.209657] [DISP] disp_get_layer_1,line:136: [ 0.209662] disp0 layer2: 0,0,2 [ 0.209670] [DISP] disp_get_layer_1,line:136: [ 0.209674] disp0 layer3: 0,0,3 [ 0.209682] [DISP] disp_get_layer_1,line:136: [ 0.209687] disp0 layer4: 0,1,0 [ 0.209695] [DISP] disp_get_layer_1,line:136: [ 0.209699] disp0 layer5: 0,1,1 [ 0.209708] [DISP] disp_get_layer_1,line:136: [ 0.209712] disp0 layer6: 0,1,2 [ 0.209721] [DISP] disp_get_layer_1,line:136: [ 0.209725] disp0 layer7: 0,1,3 [ 0.209735] [DISP] disp_device_set_manager,line:23: [ 0.209738] device 0, mgr 0 [ 0.209747] [DISP] disp_get_smbl,line:37: [ 0.209750] get smbl0 ok [ 0.209760] [DISP] disp_get_layer_1,line:136: [ 0.209765] disp1 layer8: 1,0,0 [ 0.209773] [DISP] disp_get_layer_1,line:136: [ 0.209778] disp1 layer9: 1,0,1 [ 0.209787] [DISP] disp_get_layer_1,line:136: [ 0.209791] disp1 layer10: 1,0,2 [ 0.209800] [DISP] disp_get_layer_1,line:136: [ 0.209804] disp1 layer11: 1,0,3 [ 0.209813] [DISP] disp_get_smbl,line:37: [ 0.209816] get smbl1 ok [ 0.210016] [DISP] disp_lcd_set_panel_funs,line:2446: [ 0.210024] lcd 0, driver_name default_panel, panel_name default_lcd [ 0.210038] [DISP] disp_get_lcd,line:88: [ 0.210041] disp 1 not support lcd output [ 0.210048] [DISP] disp_lcd_set_panel_funs,line:2446: [ 0.210053] lcd 0, driver_name default_panel, panel_name he0801a068 [ 0.210061] [DISP] disp_get_lcd,line:88: [ 0.210064] disp 1 not support lcd output [ 0.210071] [DISP] disp_lcd_set_panel_funs,line:2446: [ 0.210076] lcd 0, driver_name default_panel, panel_name inet_dsi_panel [ 0.210084] [DISP] disp_get_lcd,line:88: [ 0.210086] disp 1 not support lcd output [ 0.210094] [DISP] disp_lcd_set_panel_funs,line:2446: [ 0.210098] lcd 0, driver_name default_panel, panel_name lq101r1sx03 [ 0.210106] [DISP] disp_get_lcd,line:88: [ 0.210109] disp 1 not support lcd output [ 0.210117] [DISP] disp_lcd_set_panel_funs,line:2446: [ 0.210121] lcd 0, driver_name default_panel, panel_name WilliamLcd [ 0.210129] [DISP] disp_get_lcd,line:88: [ 0.210131] disp 1 not support lcd output [ 0.210139] [DISP] disp_lcd_set_panel_funs,line:2446: [ 0.210144] lcd 0, driver_name default_panel, panel_name CC08021801_310_800X1280 [ 0.210152] [DISP] disp_get_lcd,line:88: [ 0.210154] disp 1 not support lcd output [ 0.210162] [DISP] disp_lcd_set_panel_funs,line:2446: [ 0.210166] lcd 0, driver_name default_panel, panel_name tft08006 [ 0.210174] [DISP] disp_get_lcd,line:88: [ 0.210177] disp 1 not support lcd output [ 0.210184] [DISP] disp_lcd_set_panel_funs,line:2446: [ 0.210189] lcd 0, driver_name default_panel, panel_name bp101wx1 [ 0.210197] [DISP] disp_get_lcd,line:88: [ 0.210199] disp 1 not support lcd output [ 0.210207] [DISP] disp_lcd_set_panel_funs,line:2446: [ 0.210211] lcd 0, driver_name default_panel, panel_name k101im2qa04 [ 0.210219] [DISP] disp_get_lcd,line:88: [ 0.210222] disp 1 not support lcd output [ 0.210230] [DISP] disp_lcd_set_panel_funs,line:2446: [ 0.210234] lcd 0, driver_name default_panel, panel_name fx070 [ 0.210241] [DISP] disp_get_lcd,line:88: [ 0.210244] disp 1 not support lcd output [ 0.210252] [DISP] disp_lcd_set_panel_funs,line:2446: [ 0.210256] lcd 0, driver_name default_panel, panel_name K080_IM2HYL802R_800X1280 [ 0.210264] [DISP] disp_get_lcd,line:88: [ 0.210267] disp 1 not support lcd output [ 0.210275] [DISP] disp_lcd_set_panel_funs,line:2446: [ 0.210279] lcd 0, driver_name default_panel, panel_name K101_IM2BYL02_L_800X1280 [ 0.210287] [DISP] disp_get_lcd,line:88: [ 0.210290] disp 1 not support lcd output [ 0.210298] [DISP] disp_lcd_set_panel_funs,line:2446: [ 0.210302] lcd 0, driver_name default_panel, panel_name super_lcd_driver [ 0.210310] [DISP] disp_get_lcd,line:88: [ 0.210313] disp 1 not support lcd output [ 0.210321] [DISP] fb_init,line:2291: [ 0.210323] [DISP] fb_init [ 0.210337] [DISP] disp_boot_para_parse,line:1172: [ 0.210341] [DISP] fb_base:0x0 [ 0.210367] [DISP] disp_fb_to_var,line:400: [ 0.210375] fmt0 para: 32bpp, a(24,8),r(16,8),g(8,8),b(0,8) [ 0.210387] display_fb_request,fb_id:0 [ 0.213431] [DISP] __disp_ion_alloc_coherent,line:1555: [ 0.213438] ion map kernel, vaddr=0x(____ptrval____) [ 0.213545] [DISP] fb_map_video_memory,line:115: [ 0.213552] fb_map_video_memory(reserve),va=0x(____ptrval____), pa=0x(____ptrval____) size:0x2ee000 [ 0.220867] [DISP] Fb_map_kernel_logo,line:1806: [ 0.220870] Fb_map_kernel_logo failed! [ 0.225751] Freeing logo buffer memory: 1500K [ 0.225767] [DISP] var_to_disp_fb,line:521: [ 0.225775] format0,para:32bpp,a(24,8),r(16,8),g(8,8),b(0,8) [ 0.225785] [DISP] disp_mgr_set_layer_config,line:1597: [ 0.225788] mgr0, config 1 layers [ 0.225797] [DISP] disp_mgr_set_layer_config,line:1604: [ 0.225810] layer:ch1, layer0, format=0, size=<800,480>, crop=<0,0,800,480>,frame=<800,480>, en=1 addr[0xffc00000,0x0,0x0> alpha=<0,255> [ 0.225823] [DISP] disp_get_layer,line:103: [ 0.225827] 0,1,0, name=mgr0 chn1 lyr0 [ 0.225838] [DISP] disp_lyr_save_and_dirty_check,line:528: [ 0.225849] layer:ch1, layer0, format=0, size=<800,480>, crop=<0,0,800,480>,frame=<800,480>, en=1 addr[0xffc00000,0x0,0x0> [ 0.225859] [DISP] disp_mgr_apply,line:2442: [ 0.225861] mgr 0 apply [ 0.225873] [DISP] bsp_disp_shadow_protect,line:719: [ 0.225877] sel=0, protect:1, cnt=1 [ 0.225890] [DISP] de_al_lyr_apply,line:485: [ 0.225894] ch0 z 0 dis [ 0.225902] [DISP] de_al_lyr_apply,line:485: [ 0.225905] ch1 z 0 en [ 0.225913] [DISP] de_al_lyr_apply,line:488: [ 0.225916] pipe0 z 1 en [ 0.225923] [DISP] de_al_lyr_apply,line:488: [ 0.225926] pipe1 z 0 dis [ 0.225935] [DISP] de_al_lyr_apply,line:503: [ 0.225937] format[0]=0 [ 0.225957] [DISP] de_calc_overlay_scaler_para,line:178: [ 0.225960] ovl_rect[0]=<0,0> [ 0.225968] [DISP] de_calc_overlay_scaler_para,line:180: [ 0.225973] bld_rect[0]=<0,0,0,0> [ 0.225981] [DISP] de_calc_ovl_coord,line:389: [ 0.225984] half_shift_xy=<20000,18,0> [ 0.225993] [DISP] de_calc_ovl_coord,line:389: [ 0.225996] half_shift_xy=<20000,18,0> [ 0.226004] [DISP] de_rtmx_calc_chnrect,line:1982: [ 0.226007] layernum=4, i=0 [ 0.226015] [DISP] de_rtmx_calc_chnrect,line:1984: [ 0.226018] crop=<0,0,800,480> [ 0.226026] [DISP] de_rtmx_calc_chnrect,line:1986: [ 0.226030] layer=<0,0,800,480> [ 0.226038] [DISP] de_rtmx_calc_chnrect,line:1995: [ 0.226042] ovl_rect=<0,0,800,480> [ 0.226050] [DISP] de_rtmx_calc_chnrect,line:1997: [ 0.226054] bld_rect=<0,0,800,480> [ 0.226061] [DISP] de_calc_overlay_scaler_para,line:178: [ 0.226065] ovl_rect[1]=<800,480> [ 0.226072] [DISP] de_calc_overlay_scaler_para,line:180: [ 0.226077] bld_rect[1]=<0,0,800,480> [ 0.226085] [DISP] de_calc_overlay_scaler_para,line:187: [ 0.226092] fmt[0]=0, ovlw[0]=0,ovlh[0]=0, bld_rect[0].w=0, bld_rect[0].h=0 [ 0.226103] [DISP] de_vsu_set_para,line:274: [ 0.226109] sel0, ch 0, en=0, in<0x0>,out<0x0> [ 0.226132] [DISP] de_al_lyr_apply,line:713: [ 0.226137] sel=0, pipe_rect[0]=<0,0,800,480> [ 0.226146] [DISP] de_rtmx_set_route,line:1792: [ 0.226151] sel0, pno0, zorder1, route:0x0 [ 0.226159] [DISP] de_rtmx_set_route,line:1796: [ 0.226164] addr=0x(____ptrval____), reg=0x1 [ 0.226172] [DISP] de_al_lyr_apply,line:713: [ 0.226177] sel=0, pipe_rect[1]=<0,0,0,0> [ 0.226185] [DISP] de_rtmx_set_route,line:1792: [ 0.226190] sel0, pno1, zorder0, route:0x1 [ 0.226197] [DISP] de_rtmx_set_route,line:1796: [ 0.226201] addr=0x(____ptrval____), reg=0x1 [ 0.226236] [DISP] de_enhance_apply,line:204: [ 0.226240] disp 0, en=0, sharp=0 [ 0.226256] [DISP] de_peak_enable,line:123: [ 0.226260] sel=0, chno=0, en=0 [ 0.226274] [DISP] bsp_disp_shadow_protect,line:719: [ 0.226278] sel=0, protect:0, cnt=0 [ 0.226576] [DISP] disp_mgr_sw_enable,line:2645: [ 0.226581] mgr 0 enable [ 0.226593] [DISP] disp_mgr_clk_enable,line:1055: [ 0.226596] set DE rate to 300000000 [ 0.226618] [DISP] disp_mgr_clk_enable,line:1071: [ 0.226621] mgr 0 clk enable [ 0.226643] [DISP] disp_mgr_sw_enable,line:2693: [ 0.226648] output res: 800 x 480, cs=0, range=1, interlace=0 [ 0.226664] [DISP] disp_mgr_apply,line:2442: [ 0.226666] mgr 0 apply [ 0.226676] [DISP] bsp_disp_shadow_protect,line:719: [ 0.226680] sel=0, protect:1, cnt=1 [ 0.226689] disp_al_manager_apply ouput_type:1 [ 0.226698] [DISP] de_dcsc_apply,line:74: [ 0.226703] sel=0, in_fmt=0, mode=0, out_fmt=0, mode=0, range=1 [ 0.226727] [DISP] de_al_lyr_apply,line:485: [ 0.226730] ch0 z 0 dis [ 0.226738] [DISP] de_al_lyr_apply,line:485: [ 0.226742] ch1 z 0 en [ 0.226749] [DISP] de_al_lyr_apply,line:488: [ 0.226752] pipe0 z 1 en [ 0.226759] [DISP] de_al_lyr_apply,line:488: [ 0.226762] pipe1 z 0 dis [ 0.226771] [DISP] de_al_lyr_apply,line:503: [ 0.226773] format[0]=0 [ 0.226791] [DISP] de_calc_overlay_scaler_para,line:178: [ 0.226795] ovl_rect[0]=<0,0> [ 0.226804] [DISP] de_calc_overlay_scaler_para,line:180: [ 0.226808] bld_rect[0]=<0,0,0,0> [ 0.226816] [DISP] de_calc_ovl_coord,line:389: [ 0.226820] half_shift_xy=<20000,18,0> [ 0.226828] [DISP] de_calc_ovl_coord,line:389: [ 0.226832] half_shift_xy=<20000,18,0> [ 0.226839] [DISP] de_rtmx_calc_chnrect,line:1982: [ 0.226842] layernum=4, i=0 [ 0.226850] [DISP] de_rtmx_calc_chnrect,line:1984: [ 0.226854] crop=<0,0,800,480> [ 0.226861] [DISP] de_rtmx_calc_chnrect,line:1986: [ 0.226865] layer=<0,0,800,480> [ 0.226873] [DISP] de_rtmx_calc_chnrect,line:1995: [ 0.226877] ovl_rect=<0,0,800,480> [ 0.226885] [DISP] de_rtmx_calc_chnrect,line:1997: [ 0.226889] bld_rect=<0,0,800,480> [ 0.226896] [DISP] de_calc_overlay_scaler_para,line:178: [ 0.226900] ovl_rect[1]=<800,480> [ 0.226907] [DISP] de_calc_overlay_scaler_para,line:180: [ 0.226912] bld_rect[1]=<0,0,800,480> [ 0.226920] [DISP] de_calc_overlay_scaler_para,line:187: [ 0.226927] fmt[0]=0, ovlw[0]=0,ovlh[0]=0, bld_rect[0].w=0, bld_rect[0].h=0 [ 0.226938] [DISP] de_vsu_set_para,line:274: [ 0.226943] sel0, ch 0, en=0, in<0x0>,out<0x0> [ 0.226974] [DISP] de_al_lyr_apply,line:713: [ 0.226979] sel=0, pipe_rect[0]=<0,0,800,480> [ 0.226988] [DISP] de_rtmx_set_route,line:1792: [ 0.226993] sel0, pno0, zorder1, route:0x0 [ 0.227001] [DISP] de_rtmx_set_route,line:1796: [ 0.227006] addr=0x(____ptrval____), reg=0x1 [ 0.227014] [DISP] de_al_lyr_apply,line:713: [ 0.227019] sel=0, pipe_rect[1]=<0,0,0,0> [ 0.227027] [DISP] de_rtmx_set_route,line:1792: [ 0.227031] sel0, pno1, zorder0, route:0x1 [ 0.227039] [DISP] de_rtmx_set_route,line:1796: [ 0.227043] addr=0x(____ptrval____), reg=0x1 [ 0.227060] [DISP] bsp_disp_shadow_protect,line:719: [ 0.227064] sel=0, protect:0, cnt=0 [ 0.227076] [DISP] disp_enhance_apply,line:126: [ 0.227079] disp_enhance_apply, screen 0 [ 0.227087] [DISP] bsp_disp_shadow_protect,line:719: [ 0.227091] sel=0, protect:1, cnt=1 [ 0.227099] [DISP] de_dcsc_apply,line:74: [ 0.227105] sel=0, in_fmt=0, mode=0, out_fmt=0, mode=0, range=1 [ 0.227117] [DISP] de_enhance_apply,line:204: [ 0.227122] disp 0, en=0, sharp=0 [ 0.227135] [DISP] de_peak_enable,line:123: [ 0.227139] sel=0, chno=0, en=0 [ 0.227152] [DISP] bsp_disp_shadow_protect,line:719: [ 0.227155] sel=0, protect:0, cnt=0 [ 0.227172] [DISP] disp_enhance_apply,line:126: [ 0.227175] disp_enhance_apply, screen 0 [ 0.227184] [DISP] bsp_disp_shadow_protect,line:719: [ 0.227187] sel=0, protect:1, cnt=1 [ 0.227195] [DISP] de_dcsc_apply,line:74: [ 0.227200] sel=0, in_fmt=0, mode=0, out_fmt=0, mode=0, range=1 [ 0.227211] [DISP] de_enhance_apply,line:204: [ 0.227215] disp 0, en=1, sharp=0 [ 0.227224] [DISP] de_peak_enable,line:123: [ 0.227228] sel=0, chno=0, en=0 [ 0.227240] [DISP] bsp_disp_shadow_protect,line:719: [ 0.227244] sel=0, protect:0, cnt=0 [ 0.227255] panel->lcd_dclk_freq:25 panel->lcd_dclk_freq:25 tcon_div 11 [ 0.227278] [DISP] lcd_clk_config,line:732: [ 0.227289] disp 0, clk: pll(275000000),clk(275000000),dclk(25000000) dsi_rate(275000000) [ 0.227289] clk real:pll(288000000),clk(288000000),dclk(26181818) dsi_rate(0) [ 0.227310] panel->lcd_dclk_freq:25 panel->lcd_dclk_freq:25 tcon_div 11 [ 0.227318] [DISP] cal_real_frame_period,line:647: [ 0.227322] lcd frame period:15458666 [ 0.227333] [DISP] disp_sys_register_irq,line:113: [ 0.227340] disp_sys_register_irq, irqNo=30, Handler=0x(____ptrval____), pArg=0x(____ptrval____) [ 0.227397] [DISP] disp_init,line:2441: [ 0.227400] disp_init finish [ 0.227476] [DISP] disp_probe,line:3118: [ 0.227479] [DISP]disp_probe finish [ 0.227874] [DISP]disp_module_init finish [ 0.228725] sunxi_sid_init()551 - insmod ok [ 0.229240] pwm-regulator: supplied by regulator-dummy [ 0.235965] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator [ 0.236534] uart uart0: get regulator failed [ 0.236561] uart uart0: uart0 supply uart not found, using dummy regulator [ 0.236871] uart0: ttyS0 at MMIO 0x2500000 (irq = 18, base_baud = 1500000) is a SUNXI [ 0.236895] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n [ 1.734767] printk: console [ttyS0] enabled [ 1.740254] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator [ 1.751653] uart uart1: get regulator failed [ 1.756429] uart uart1: uart1 supply uart not found, using dummy regulator [ 1.764492] uart1: ttyS1 at MMIO 0x2500400 (irq = 19, base_baud = 1500000) is a SUNXI [ 1.774325] misc dump reg init [ 1.778557] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9 [ 1.785804] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed [ 1.793117] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed [ 1.800510] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1) [ 1.807041] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power. [ 1.813972] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1) [ 1.821692] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1 [ 1.829511] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1 [ 1.837635] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled [ 1.845281] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power. [ 1.852041] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1) [ 1.859543] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=210 assert=0 [ 1.867677] [ADDR_MGT] addr_mgt_probe: module version: v1.0.10 [ 1.875303] [ADDR_MGT] addr_mgt_probe: success. [ 1.881636] libphy: Fixed MDIO Bus: probed [ 1.886207] CAN device driver interface [ 1.891612] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator [ 1.902918] sunxi gmac driver's version: 1.0.0 [ 1.908023] gmac-power0: NULL [ 1.911372] gmac-power1: NULL [ 1.914676] gmac-power2: NULL [ 1.919193] Failed to alloc md5 [ 1.922785] eth0: Use random mac address [ 1.927486] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.934854] sunxi-ehci: EHCI SUNXI driver [ 1.939838] get ehci1-controller wakeup-source is fail. [ 1.945854] sunxi ehci1-controller don't init wakeup source [ 1.952148] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xffffffe00094f758, 0x:ffffffd00407a000, irq_no:31 [ 1.965705] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply drvvbus not found, using dummy regulator [ 1.978268] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator [ 1.990484] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller [ 1.997745] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1 [ 2.007563] sunxi-ehci 4200000.ehci1-controller: irq 49, io mem 0x04200000 [ 2.040727] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00 [ 2.049386] hub 1-0:1.0: USB hub found [ 2.053680] hub 1-0:1.0: 1 port detected [ 2.058791] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.065779] sunxi-ohci: OHCI SUNXI driver [ 2.070863] get ohci1-controller wakeup-source is fail. [ 2.076798] sunxi ohci1-controller don't init wakeup source [ 2.083051] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xffffffe0009502b0 [ 2.093473] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply drvvbus not found, using dummy regulator [ 2.105983] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator [ 2.118191] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller [ 2.125460] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2 [ 2.135234] sunxi-ohci 4200400.ohci1-controller: irq 50, io mem 0x04200400 [ 2.215617] hub 2-0:1.0: USB hub found [ 2.219848] hub 2-0:1.0: 1 port detected [ 2.225240] usbcore: registered new interface driver uas [ 2.231404] usbcore: registered new interface driver usb-storage [ 2.238161] usbcore: registered new interface driver ums-alauda [ 2.244900] usbcore: registered new interface driver ums-cypress [ 2.251704] usbcore: registered new interface driver ums-datafab [ 2.258456] usbcore: registered new interface driver ums_eneub6250 [ 2.265449] usbcore: registered new interface driver ums-freecom [ 2.272256] usbcore: registered new interface driver ums-isd200 [ 2.278918] usbcore: registered new interface driver ums-jumpshot [ 2.285817] usbcore: registered new interface driver ums-karma [ 2.292421] usbcore: registered new interface driver ums-onetouch [ 2.299288] usbcore: registered new interface driver ums-realtek [ 2.306090] usbcore: registered new interface driver ums-sddr09 [ 2.312796] usbcore: registered new interface driver ums-sddr55 [ 2.319466] usbcore: registered new interface driver ums-usbat [ 2.326554] sunxi_gpadc_init,2151, success [ 2.332060] sunxi-rtc 7090000.rtc: errata__fix_alarm_day_reg_default_value(): ALARM0_DAY_REG=0, set it to 1 [ 2.344249] sunxi-rtc 7090000.rtc: registered as rtc0 [ 2.349996] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:06 UTC (6) [ 2.358913] sunxi-rtc 7090000.rtc: sunxi rtc probed [ 2.364836] i2c /dev entries driver [ 2.368843] IR NEC protocol handler initialized [ 2.374586] sunxi cedar version 1.1 [ 2.378723] sunxi-cedar 1c0e000.ve: Adding to iommu group 0 [ 2.385009] VE: install start!!! [ 2.385009] [ 2.390468] VE: cedar-ve the get irq is 6 [ 2.390468] [ 2.396849] VE: ve_debug_proc_info:(____ptrval____), data:(____ptrval____), lock:(____ptrval____) [ 2.396849] [ 2.408428] VE: install end!!! [ 2.408428] [ 2.413495] VE: sunxi_cedar_probe [ 2.418723] sunxi-wdt 6011000.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 2.427858] Bluetooth: HCI UART driver ver 2.3 [ 2.432856] Bluetooth: HCI UART protocol H4 registered [ 2.438582] Bluetooth: HCI UART protocol BCSP registered [ 2.444523] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10 [ 2.451786] [XR_BT_LPM] bluesleep_probe: bt_wake polarity: 1 [ 2.458150] [XR_BT_LPM] bluesleep_probe: host_wake polarity: 1 [ 2.464724] [XR_BT_LPM] bluesleep_probe: wakeup source is disabled! [ 2.464724] [ 2.473389] [XR_BT_LPM] bluesleep_probe: uart_index(1) [ 2.482126] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.21 2021-11-18 10:02) [ 2.492090] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8 [ 2.498255] sunxi-mmc 4020000.sdmmc: No vmmc regulator found [ 2.504599] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found [ 2.511024] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found [ 2.517428] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found [ 2.523948] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found [ 2.530450] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found [ 2.536970] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found [ 2.543913] sunxi-mmc 4020000.sdmmc: Got CD GPIO [ 2.549411] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail [ 2.556087] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.567218] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator [ 2.587356] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.611715] sunxi-mmc 4020000.sdmmc: detmode:gpio irq [ 2.617408] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.629639] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.21 2021-11-18 10:02) [ 2.639700] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8 [ 2.645935] sunxi-mmc 4021000.sdmmc: No vmmc regulator found [ 2.652318] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found [ 2.658751] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.670321] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found [ 2.676750] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found [ 2.683372] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found [ 2.689907] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found [ 2.696472] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found [ 2.703054] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed [ 2.711751] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.724310] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.735478] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 2.744398] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.755980] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.780254] sunxi-mmc 4021000.sdmmc: detmode:manually by software [ 2.787848] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.799898] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator [ 2.811264] sunxi_led_probe()1749 - start [ 2.815847] sunxi_get_str_of_property()1595 - failed to get the string of propname led_regulator! [ 2.825840] sunxi_register_led_classdev()1483 - led_classdev start [ 2.832807] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.848651] sunxi_led_probe()1845 - finish [ 2.853300] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.862948] usbcore: registered new interface driver usbhid [ 2.869236] usbhid: USB HID core driver [ 2.873594] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.885072] sunxi-mmc 4021000.sdmmc: card claims to support voltages below defined range [ 2.894234] rpmsg_client_dsp_standby 3003000.msgbox.sunxi,dsp-power-msgbox.512.256: new channel: 0x200 -> 0x100! [ 2.905742] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.919494] usbcore: registered new interface driver snd-usb-audio [ 2.927219] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 2.941648] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator [ 2.952776] mmc0: new high speed SDHC card at address aaaa [ 2.960290] sunxi-daudio 2034000.daudio: regulator missing or invalid [ 2.968775] mmcblk0: mmc0:aaaa SD32G 29.7 GiB [ 2.974547] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.986462] [AUDIOCODEC][sunxi_codec_parse_params][2412]:digital_vol:0, lineout_vol:26, mic1gain:19, mic2gain:19 pa_msleep:120, pa_level:1, pa_pwr_level:1 [ 2.986462] [ 3.003697] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 3.015387] [AUDIOCODEC][sunxi_codec_parse_params][2448]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0 [ 3.026554] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 3.040173] [AUDIOCODEC][sunxi_internal_codec_probe][2609]:codec probe finished [ 3.049759] mmc1: new high speed SDIO card at address 0001 [ 3.057182] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 [ 3.062714] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present! [ 3.075475] [SNDCODEC][sunxi_card_init][583]:card init finished [ 3.084262] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok [ 3.095455] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input1 [ 3.107515] [SNDCODEC][sunxi_card_dev_probe][836]:register card finished [ 3.115697] sunxi-rpaf-dsp soc@3000000:rpaf-dsp@203034c: register device finished! [ 3.124206] sunxi-rpaf-dsp soc@3000000:rpaf-dsp@203034c: [rpaf_dsp0] probe finished! [ 3.133246] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: id:sunxi,dsp-msgbox new channel: 0x202 -> 0x102! [ 3.144780] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: rpmsg hifi[0] client driver is probed [ 3.156629] NET: Registered protocol family 10 [ 3.163027] Segment Routing with IPv6 [ 3.167298] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.174718] NET: Registered protocol family 17 [ 3.179749] can: controller area network core (rev 20170425 abi 9) [ 3.186811] NET: Registered protocol family 29 [ 3.191831] can: raw protocol (rev 20170425) [ 3.196591] can: broadcast manager protocol (rev 20170425 t) [ 3.202939] can: netlink gateway (rev 20190810) max_hops=1 [ 3.209346] Bluetooth: RFCOMM TTY layer initialized [ 3.214891] Bluetooth: RFCOMM socket layer initialized [ 3.220644] Bluetooth: RFCOMM ver 1.11 [ 3.225834] Loading compiled-in X.509 certificates [ 3.233419] HDMI 2.0 driver init start! [ 3.237714] [DISP] disp_boot_para_parse,line:1172: [ 3.237718] [DISP] boot_disp:0x104 [ 3.246910] boot_hdmi=false [ 3.250093] ERROR: pinctrl_get for HDMI2.0 DDC fail [ 3.256886] [DISP] bsp_disp_set_hdmi_func,line:1340: [ 3.256890] registered!! [ 3.265551] HDMI2.0 module init end [ 3.294388] sunxi-i2c sunxi-i2c2: sunxi-i2c2 supply twi not found, using dummy regulator [ 3.320955] sunxi-i2c sunxi-i2c2: Bus error [ 3.325691] sunxi-i2c sunxi-i2c2: engine-mode: bus state: 0x0, isn't idle [ 3.333256] sunxi-i2c sunxi-i2c2: STOP failed! [ 3.338242] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x38) [ 3.345889] pcf857x: probe of 2-0038 failed with error -22 [ 3.352066] sunxi-i2c sunxi-i2c2: probe success [ 3.361261] debugfs: Directory '2031000.dmic' with parent 'snddmic' already present! [ 3.371390] sunxi-audio-card 2031060.sounddmic: dmic-hifi <-> 2031000.dmic mapping ok [ 3.381519] debugfs: Directory '2034000.daudio' with parent 'sndhdmi' already present! [ 3.392125] sunxi-audio-card 20340a0.sounddaudio2: 20340a4.hdmiaudio <-> 2034000.daudio mapping ok [ 3.403386] get ehci0-controller wakeup-source is fail. [ 3.409313] sunxi ehci0-controller don't init wakeup source [ 3.415578] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe00094f390, 0x:ffffffd004bf6000, irq_no:2e [ 3.429093] [sunxi-ehci0]: Not init ehci0 [ 3.434086] get ohci0-controller wakeup-source is fail. [ 3.440020] sunxi ohci0-controller don't init wakeup source [ 3.446302] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe00094fee8 [ 3.456702] [sunxi-ohci0]: Not init ohci0 [ 3.463360] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 3.474207] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 3.481792] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 3.491467] clk: Not disabling unused clocks [ 3.496235] ALSA device list: [ 3.499538] #0: audiocodec [ 3.502871] cfg80211: failed to load regulatory.db [ 3.508281] #1: snddmic [ 3.511266] #2: sndhdmi [ 3.514195] alloc_fd: slot 0 not NULL! [ 3.523274] VFS: Mounted root (squashfs filesystem) readonly on device 179:5. [ 3.534149] devtmpfs: mounted [ 3.537619] Freeing unused kernel memory: 184K [ 3.542696] This architecture does not have kernel memory protection. [ 3.549894] Run /sbin/init as init process [ 3.811857] [SNDCODEC][sunxi_check_hs_detect_status][191]:plugin --> switch:3 [ 3.889433] [SNDCODEC][jack_interrupt][370]:KEY tempdata: 17 [ 3.895745] [SNDCODEC][jack_interrupt][436]:tempdata:0x11,Key data err: [ 4.219882] init: Console is alive [ 4.224052] init: - watchdog - [ 4.227598] init: - preinit - formating /dev/by-name/UDISK to ext4 /etc/preinit: line 1: mkfs.ext4: not found [ 5.358700] mount_root: mounting /dev/root [ 5.364253] mount_root: loading kmods from internal overlay [ 5.474169] random: procd: uninitialized urandom read (4 bytes read) [ 5.500017] block: attempting to load /etc/config/fstab [ 5.526938] block: extroot: device not present, retrying in 5 seconds [ 7.150720] hdmi_hpd_sys_config_release [ 7.160721] [ 7.160721] insmod_device_driver [ 7.160721] [ 7.167892] sunxi_usb_udc 4100000.udc-controller: 4100000.udc-controller supply udc not found, using dummy regulator [ 10.594919] block: extroot: cannot find device UDISK [ 10.612063] procd: - early - [ 10.615413] procd: - watchdog - [ 10.671122] random: procd: uninitialized urandom read (4 bytes read) [ 10.981013] procd: - watchdog - [ 10.984798] procd: - ubus - [ 10.988535] procd (1): /proc/116/oom_adj is deprecated, please use /proc/116/oom_score_adj instead. [ 11.068513] random: ubusd: uninitialized urandom read (4 bytes read) [ 11.246577] random: ubusd: uninitialized urandom read (4 bytes read) [ 11.286636] procd: - init - Please press Enter to activate this console. [ 12.477355] fuse: init (API version 7.31) [ 12.685716] file system registered [ 12.772576] configfs-gadget 4100000.udc-controller: failed to start g1: -19 [ 12.837805] usbcore: registered new interface driver uvcvideo [ 12.882353] USB Video Class driver (1.1.1) [ 13.101534] read descriptors [ 13.133479] read strings [ 13.291513] sunxi_set_cur_vol_work()397 WARN: get power supply failed [ 13.377959] android_work: sent uevent USB_STATE=CONNECTED [ 13.414404] configfs-gadget gadget: high-speed config #1: c [ 13.420803] android_work: sent uevent USB_STATE=CONFIGURED [ 15.401733] random: fast init done [ 15.492396] ======== XRADIO WIFI OPEN ======== [ 15.500337] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31 [ 15.507499] [XRADIO] Allocated hw_priv @ (____ptrval____) [ 15.515489] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 [ 15.533721] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success [ 15.739268] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 15.835544] [XRADIO] Detect SDIO card 1 [ 17.920833] sunxi-rfkill soc@3000000:rfkill@0: wlan power off success [ 18.028171] [XRADIO] Remove SDIO card 1 [ 18.042495] [SBUS_ERR] sdio probe timeout! [ 18.047060] [XRADIO_ERR] sbus_sdio_init failed [ 18.053185] xradio_core_init failed (-110)! [ 18.137002] xt_time: kernel timezone is -0000 [ 18.153490] Error: Driver 'gt9xxnew_ts' is already registered, aborting... [ 19.388542] ======== XRADIO WIFI OPEN ======== [ 19.394124] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31 [ 19.400962] [XRADIO] Allocated hw_priv @ (____ptrval____) [ 19.410838] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 [ 19.436461] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success [ 19.654877] [XRADIO] Detect SDIO card 1 [ 21.680935] sunxi-rfkill soc@3000000:rfkill@0: wlan power off success [ 21.788199] [XRADIO] Remove SDIO card 1 [ 21.802525] [SBUS_ERR] sdio probe timeout! [ 21.807088] [XRADIO_ERR] sbus_sdio_init failed [ 21.813224] xradio_core_init failed (-110)! kmodloader done Trying to connect to SWUpdate... [ 24.474555] [SNDCODEC][sunxi_card_hw_params][620]:stream_flag: 0 [ 33.760754] usb1-vbus: disabling BusyBox v1.27.2 () built-in shell (ash) _____ _ __ _ |_ _||_| ___ _ _ | | |_| ___ _ _ _ _ | | _ | || | | |__ | || || | ||_'_| | | | || | || _ | |_____||_||_|_||___||_,_| |_| |_||_|_||_|_| Tina is Based on OpenWrt! ---------------------------------------------- Tina Linux (Neptune, 61CC0487) ---------------------------------------------- root@TinaLinux:/# root@TinaLinux:/# -
看这一部分：
[ 0.227255] panel->lcd_dclk_freq:25 panel->lcd_dclk_freq:25 tcon_div 11 [ 0.227278] [DISP] lcd_clk_config,line:732: [ 0.227289] disp 0, clk: pll(275000000),clk(275000000),dclk(25000000) dsi_rate(275000000) [ 0.227289] clk real:pll(288000000),clk(288000000),dclk(26181818) dsi_rate(0) [ 0.227310] panel->lcd_dclk_freq:25 panel->lcd_dclk_freq:25 tcon_div 11 [ 0.227318] [DISP] cal_real_frame_period,line:647:时钟基本正常，请问是什么 RGB 屏幕，是否需要 SPI、I2C 初始化？
也可以尝试这个 LCD 配置
lcd_driver_name = "default_lcd"; lcd_if = <0>; lcd_x = <800>; lcd_y = <480>; lcd_width = <150>; lcd_height = <94>; lcd_dclk_freq = <48>; lcd_pwm_used = <1>; lcd_pwm_ch = <7>; lcd_pwm_freq = <10000>; lcd_pwm_pol = <1>; lcd_hbp = <55>; lcd_ht = <1240>; lcd_hspw = <20>; lcd_vbp = <35>; lcd_vt = <650>; lcd_vspw = <10>; lcd_lvds_if = <0>; lcd_lvds_colordepth = <1>; lcd_lvds_mode = <0>; lcd_frm = <0>; lcd_io_phase = <0x0000>; lcd_gamma_en = <0>; lcd_bright_curve_en = <0>; lcd_cmap_en = <0>; deu_mode = <0>; lcdgamma4iep = <22>; smart_color = <90>; pinctrl-0 = <&rgb18_pins_a>; pinctrl-1 = <&rgb18_pins_b>; -
示波器看下 PCLK/DE/VSYNC/HSYNC 这几组引脚是否正常。
-
@yteraa
使用的ST7262，不需要初始化的屏
使用这些设备树配置后屏幕有显示了，但是屏幕一直都是白、红、绿、蓝、黑纯色在不停的换，期间还伴随这闪屏，怀疑是测试模式，因此去修改了echo X > /sys/class/disp/disp/attr/colorbar，发现只有闪屏的频率发生了变化，其余的没有变化
请问知道这是什么原因吗？&lcd0 { lcd_driver_name = "default_lcd"; lcd_if = <0>; lcd_x = <800>; lcd_y = <480>; lcd_width = <800>; lcd_height = <480>; lcd_dclk_freq = <25>; lcd_pwm_used = <1>; lcd_pwm_ch = <7>; lcd_pwm_freq = <10000>; lcd_pwm_pol = <1>; lcd_hbp = <8>; lcd_ht = <816>; lcd_hspw = <4>; lcd_vbp = <8>; lcd_vt = <496>; lcd_vspw = <4>; lcd_lvds_if = <0>; lcd_lvds_colordepth = <1>; lcd_lvds_mode = <0>; lcd_frm = <0>; lcd_io_phase = <0x0000>; lcd_gamma_en = <0>; lcd_bright_curve_en = <0>; lcd_cmap_en = <0>; deu_mode = <0>; lcdgamma4iep = <22>; smart_color = <90>; pinctrl-0 = <&rgb18_pins_a>; pinctrl-1 = <&rgb18_pins_b>; };
-
@whycan
HS VS没有信号
应该是使用错了驱动，安装楼上的lcd_driver_name修改后不是黑屏了 -
@yteraa
大佬，求助一下，用了default_lcd驱动后屏幕有显示了，但是显示不正常
我查了一下显示屏的参数，都是按照手册中配置的，没发现有错误，但是还是显示不正常
请问有没有什么调试方法或者建议
-
@suncw 拍照看看啥样的
-
@yteraa
这是开机默认的效果
这是随便修改一个colorbar后的效果（echo 2 > /sys/class/disp/disp/attr/colorbar）
-
对照手册检查这部分的参数
lcd_hbp = <8>; lcd_ht = <816>; lcd_hspw = <4>; lcd_vbp = <8>; lcd_vt = <496>; lcd_vspw = <4>; -
@yteraa
我对照了一下手册，lcd_hbp和lcd_vbp有点问题，修改后显示屏没有明显变化，还是之前的效果。
请问我修改后对照的参数有问题吗？lcd_hbp:hsync back porch(pixel) + hsync plus width(pixel); =Thbp+Thw = 8+4 = 12 lcd_ht: hsync total cycle(pixel) = Th = 816 lcd_hspw:hsync plus width(pixel) = Thw = 4 lcd_vbp:vsync back porch(line) + vysnc plus width(line) = Tvbp +Tvw = 8+4 = 12 lcd_vt:vysnc total cycle(line) = Tv = 496 lcd_vspw: vysnc plus width(pixel) = Tvw = 4
-
@yteraa
大佬，现在显示屏一直显示纯色，而且很有规律，请问会不会是进入了什么测试模式？咱们这款CPU有类似的功能吗？ -
@suncw RGB屏幕可能自带测试模式，参数不对就会进入测试模式，colorbar的显示也不对，感觉还是在测试模式
-
@yteraa
哦哦哦，这样呀，那我们再查一查配置的参数看看哪里有问题吧 -
@suncw
&lcd0 {lcd_driver_name = "default_lcd"; lcd_if = <0>; lcd_x = <800>; lcd_y = <480>; lcd_width = <800>; lcd_height = <480>; lcd_dclk_freq = <25>; lcd_pwm_used = <1>; lcd_pwm_ch = <7>; lcd_pwm_freq = <10000>; lcd_pwm_pol = <1>; lcd_hbp = <16>; lcd_ht = <832>; lcd_hspw = <8>; lcd_vbp = <10>; lcd_vt = <500>; lcd_vspw = <4>; //lcd_lvds_if = <0>; //lcd_lvds_colordepth = <1>; //lcd_lvds_mode = <0>; lcd_frm = <0>; lcd_io_phase = <0x0000>; lcd_gamma_en = <0>; lcd_bright_curve_en = <0>; lcd_cmap_en = <0>; deu_mode = <0>; lcdgamma4iep = <22>; smart_color = <90>; pinctrl-0 = <&rgb18_pins_a>; pinctrl-1 = <&rgb18_pins_b>;};
不知道你的原理图是否是输出24bit RGB 如果是的 请将引脚改为 rgb24_pins_a/b
按照 你原始的配置数据 dclk ！=25 约24.2左右
注释掉 lvds相关的参数，一般用不到。 -
@lovexulu
原理图输出18bit RGB (RGB666)
时钟是稍微差了一点，但是也在范围内，我往上调了一点现象还是一样，也是自测模式
lvds是也注释了，也没有效果。。。。测了一下信号，时钟是正常的，其余的DE/VSYNC/HSYNC都没有信号。。。。
-
@whycan
大佬，RGB显示屏配置完后，时钟是正常的，其余的DE/VSYNC/HSYNC都没有信号
已经检查了屏幕是参数配置，没发现什么问题
请问有没有什么怀疑点，或者调试方向？求指点 -
确认这个屏是 800x480 吗? 有没有厂家提供的手册?怎么看起来像 480x272?
-
@whycan
确认了一下，是800*480的，相关参数配置也是按照手册里进行的配置，附附件是厂家提供的手册，再麻烦帮忙看一下，多谢
ST7262_V0.6a_202003.pdf -
问下楼主这个屏幕有没有调试出来，我这边也在用这个屏幕，现象一样？
-
@suncw
从手册的时序图和参数表分析，这些参数设置对的lcd_hbp = <8>; lcd_ht = <816>; lcd_hspw = <4>; lcd_vbp = <8>; lcd_vt = <496>; lcd_vspw = <4>;芯片规格书中的Thbp(即lcd_hbp)已将包含Thw（即lcd_hspw）， 所以lcd_hbp = Thbp = 12
、
-
@koupoo
这样吗？ -
楼主解决了吗，想知道如何在rgb屏幕上打印console终端调试信息
Copyright © 2024 深圳全志在线有限公司 粤ICP备2021084185号 粤公网安备44030502007680号