麻雀开发板，spinand烧录问题，PhoenixSuit识别不到设备

[wjp2547532]

自己焊接了一个nand到开发板，上电后设备管理器里可以正常识别设备，但是PhoenixSuit软件显示无设备连接，nand型号也在支持的列表里
哪里没搞对，可以指导一下么

[whycan]

是不是全志官方的驱动？

[wjp2547532]

@whycan 是的

[whycan]

@wjp2547532
怎么识别不到的？

[wjp2547532]

@whycan

无设备连接

[wjp2547532]

@whycan 对PhoenixSuit的版本没啥要求吧？

[wjp2547532]

@whycan 晕哥，现在PhoenixSuit可以识别到设备（我下载了APST，打开APST的时候就能识别到设备，不知道为啥），但是烧写失败

24242]fes begin commit:27369ab
[24244]set pll start
[24247]periph0 has been enabled
[24250]set pll end
[24251][pmu]: bus read error
[24254]board init ok
[24256]beign to init dram
[24258]ZQ value = 0x2f***********
[24261]get_pmu_exist() = -1
[24264]ddr_efuse_type: 0xa
[24267][AUTO DEBUG] single rank and full DQ!
[24271]ddr_efuse_type: 0xa
[24274][AUTO DEBUG] rank 0 row = 13 
[24277][AUTO DEBUG] rank 0 bank = 4 
[24281][AUTO DEBUG] rank 0 page size = 2 KB 
[24285]DRAM BOOT DRIVE INFO: V0.24
[24288]DRAM CLK = 528 MHz
[24290]DRAM Type = 2 (2:DDR2,3:DDR3)
[24294]DRAMC read ODT  off.
[24296]DRAM ODT off.
[24298]ddr_efuse_type: 0xa
[24301]DRAM SIZE =64 M
[24305]DRAM simple test OK.
[24308]init dram ok


U-Boot 2018.05-g0a88ac9-config-dirty (Nov 10 2022 - 09:43:39 +0800) Allwinner Technology

[27.334]DRAM:  64 MiB
[27.339]Relocation Offset is: 01ef0000
[27.368]secure enable bit: 0
[27.372]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
[27.378]flash init start
[27.381]workmode = 16,storage type = 0
try card 2
set card number 2
get card number 2
[27.388][mmc]: mmc driver ver uboot2018:2021-04-16 14:23:00-1
[27.398][mmc]: get sdc_type fail and use default host:tm4.
[27.428][mmc]: Is not Boot mode!
[27.431][mmc]: SUNXI SDMMC Controller Version:0x50310
[27.442][mmc]: ************Try SD card 2************
[27.447][mmc]: mmc 2 cmd timeout 100 status 100
[27.451][mmc]: smc 2 err, cmd 8,  RTO
[27.455][mmc]: mmc 2 close bus gating and reset
[27.460][mmc]: mmc 2 cmd timeout 100 status 100
[27.464][mmc]: smc 2 err, cmd 55,  RTO
[27.468][mmc]: mmc 2 close bus gating and reset
[27.472][mmc]: ************Try MMC card 2************
[27.481][mmc]: mmc 2 cmd timeout 100 status 100
[27.485][mmc]: smc 2 err, cmd 1,  RTO
[27.488][mmc]: mmc 2 close bus gating and reset
[27.492][mmc]: Card did not respond to voltage select!
[27.497][mmc]: ************SD/MMC 2 init error!************
[27.503][mmc]: mmc init product failed
MMC init failed
try emmc fail
[27.518]sunxi-spinand: AW SPINand MTD Layer Version: 1.5 20200407
[27.524]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.9 20200306
[27.584]sunxi-spinand-phy: request spi0 gpio ok
[27.588]sunxi-spinand-phy: request general tx dma channel ok!
[27.593]sunxi-spinand-phy: request general rx dma channel ok!
[27.599]sunxi-spinand-phy: set spic0 clk to 20 Mhz
[27.603]sunxi-spinand-phy: init spic0 clk ok
[27.607]sunxi-spinand-phy: not detect any munufacture from id table
[27.623]sunxi-spinand-phy: get spi-nand Model from fdt fail
[27.628]sunxi-spinand-phy: get phy info from fdt fail
[27.633]sunxi-spinand-phy: not detect munufacture from fdt
[27.638]sunxi-spinand-phy: detect munufacture from id table: Winbond
[27.644]sunxi-spinand-phy: detect spinand id: ff21aaef ffffffff
[27.649]sunxi-spinand-phy: ========== arch info ==========
[27.655]sunxi-spinand-phy: Model:               W25N01GVZEIG
[27.660]sunxi-spinand-phy: Munufacture:         Winbond
[27.665]sunxi-spinand-phy: DieCntPerChip:       1
[27.669]sunxi-spinand-phy: BlkCntPerDie:        1024
[27.674]sunxi-spinand-phy: PageCntPerBlk:       64
[27.679]sunxi-spinand-phy: SectCntPerPage:      4
[27.683]sunxi-spinand-phy: OobSizePerPage:      64
[27.688]sunxi-spinand-phy: BadBlockFlag:        0x0
[27.692]sunxi-spinand-phy: OperationOpt:        0x7
[27.697]sunxi-spinand-phy: MaxEraseTimes:       65000
[27.701]sunxi-spinand-phy: EccFlag:             0x0
[27.706]sunxi-spinand-phy: EccType:             2
[27.711]sunxi-spinand-phy: EccProtectedType:    3
[27.715]sunxi-spinand-phy: ========================================
[27.721]sunxi-spinand-phy: 
[27.723]sunxi-spinand-phy: ========== physical info ==========
[27.729]sunxi-spinand-phy: TotalSize:    128 M
[27.733]sunxi-spinand-phy: SectorSize:   512 B
[27.737]sunxi-spinand-phy: PageSize:     2 K
[27.741]sunxi-spinand-phy: BlockSize:    128 K
[27.745]sunxi-spinand-phy: OOBSize:      64 B
[27.750]sunxi-spinand-phy: ========================================
[27.755]sunxi-spinand-phy: 
[27.758]sunxi-spinand-phy: ========== logical info ==========
[27.763]sunxi-spinand-phy: TotalSize:    128 M
[27.768]sunxi-spinand-phy: SectorSize:   512 B
[27.772]sunxi-spinand-phy: PageSize:     4 K
[27.776]sunxi-spinand-phy: BlockSize:    256 K
[27.780]sunxi-spinand-phy: OOBSize:      128 B
[27.784]sunxi-spinand-phy: ========================================
[27.800]sunxi-spinand-phy: W25N01GVZEIG reset rx bit width to 1
[27.805]sunxi-spinand-phy: W25N01GVZEIG reset tx bit width to 1
[27.811]sunxi-spinand-phy: set spic0 clk to 100 Mhz
[27.815]sunxi-spinand-phy: block lock register: 0x00
[27.820]sunxi-spinand-phy: feature register: 0x19
[27.825]sunxi-spinand-phy: sunxi physic nand init end
[27.834]Loading Environment from SUNXI_FLASH... OK
[27.842]try to burn key
[27.846]out of usb burn from boot: not need burn key
Hit any key to stop autoboot:  0 
sunxi work mode=0x10
run usb efex
delay time 2500
weak:otg_phy_config
usb init ok
set address 0xa
set address 0xa ok
set address 0xb
set address 0xb ok

晕哥帮忙看一下可能是啥原因，我做的烧写包有问题么？

[whycan]

@wjp2547532
试一试这个固件： (8.8寸长条形烧录固件)tina_t113-whycanpij_uart3.img

[wjp2547532]

@whycan 这个固件也不行，D1s可以用这个固件？晕哥，你那里有现成的D1s麻雀的spi-nand的固件么，我想先验证一下烧写有没有问题

[whycan]

@wjp2547532

D1s SPI NAND 固件： tina_d1s-whycanpij_uart3(HSD088测试固件).img

原理图： https://oshwhub.com/GloomyGhost/34e1fe88b79f49b891df150db9c34cc4

[wjp2547532]

@whycan 好的晕哥，谢谢，我去试一下

[kelsey]

@wjp2547532 烧录的log目前是所有的log了吗？已经烧录的进度目前是卡在了多少呢

[wjp2547532]

@kelsey 已经可以烧录了，应该是PC端驱动的问题，换了一台电脑重新安装软件后可以识别设备并烧录了，谢谢大佬关心