V851SE 修改为 spi nand flash 无法正常启动

[tanlining]

[23]HELLO! BOOT0 is starting!
[26]BOOT0 commit : 4b419f21ba
[114][pmu]: bus read error
[117]set pll start
[119]periph0 has been enabled
[122]set pll end
[123]board init ok
[125]DRAM use internal ZQ!!
[128]ZQ value = 0x2e
[130]chip id check OK
[132]POWER SETTING ERROR!
[134]DRAM BOOT DRIVE INFO: V0.16
[137]DRAM CLK = 528 MHz
[140]DRAM Type = 2 (2:DDR2,3:DDR3)
[143]DRAMC read ODT  off.
[145]DRAM ODT off.
[148]DRAM SIZE =64 M
[150]dram_tpr4:0x0
[158]DRAM simple test OK.
[160]rtc standby flag is 0x0, super standby flag is 0x0
[165]dram size =64
[168]audio:avcc calibration
[171]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32
[176]block from 8 to 32
[544]Check is correct.
[547]Entry_name        = optee
[550]Entry_name        = u-boot
[558]Entry_name        = dtb
[561]Jump to second Boot.
M/TC: OP-TEE version: 15ee1539b (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Tue Mar 29 06:48:41 UTC 2022 arm
E/TC:0 0 platform_standby_fdt_parse:133 no pmu node
E/TC:0 0 sunxi_twi_parse_from_dt:121 no pmu node


U-Boot 2018.05-ga697d75 (Jul 28 2022 - 05:29:47 +0000) Allwinner Technology

[00.639]CPU:   Allwinner Family
[00.642]Model: sun8iw21
I2C:   [I2C-ERROR]:twi_send_clk_9pulse() 147 SDA is still Stuck Low, failed. 
ready
[00.702]DRAM:  64 MiB
[00.705]Relocation Offset is: 00ed0000
[00.738]secure enable bit: 0
E/TC:0   tee_read_fdt:433 fine node /firmware/optee failed with FDT_ERR_NOTFOUND
[00.753]smc_tee_inform_fdt failed with: ffff0000
[I2C-ERROR]:twi_stop() 339 STOP can't sendout!
[00.763]pmu_axp2101_probe pmic_bus_read fail
[I2C-ERROR]:twi_stop() 339 STOP can't sendout!
[00.771]bmu_axp2101_probe pmic_bus_read fail
[00.775]CPU=900 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=24Mhz  MBus=300Mhz
[00.781]gic: sec monitor mode
sunxi flash map init
[00.786]flash init start
[00.788]workmode = 0,storage type = 0
[00.796]sunxi-spinand-phy: spinand sample_mode:1 sample_delay:12

device nand0 <nand>, # parts = 4
 #: name                size            offset          mask_flags
 0: boot0               0x00100000      0x00000000      1
 1: uboot               0x00300000      0x00100000      1
 2: secure_storage      0x00100000      0x00400000      1
 3: sys                 0x07b00000      0x00500000      0

active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000

defaults:
mtdids  : nand0=nand
mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
[00.952]ubi0: attaching mtd4
[01.165]ubi0: scanning is finished
[01.175]ubi0: attached mtd4 (name "sys", size 123 MiB)
[01.179]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[01.186]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[01.192]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[01.198]ubi0: good PEBs: 492, bad PEBs: 0, corrupted PEBs: 0
[01.203]ubi0: user volume: 7, internal volumes: 1, max. volumes count: 128
[01.210]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
[01.218]ubi0: available PEBs: 0, total reserved PEBs: 492, PEBs reserved for bad PEB handling: 20
[01.226]sunxi flash init ok
[01.229]line:724 init_clocks
[01.232]drv_disp_init
[01.242]drv_disp_init finish
[01.397]Loading Environment from SUNXI_FLASH... OK
[01.433]boot_gui_init:start
partno erro : can't find partition Reserve0
[01.461]Get Reserve0 partition number fail!
[01.468]boot_gui_init:finish
partno erro : can't find partition bootloader
partno erro : can't find partition boot-resource
[01.522]Get bootloader and boot-resource partition number fail!
[01.530]Item0 (Map) magic is bad
[01.533]out of usb burn from boot: not need burn key
[01.559]update bootcmd
[01.583]change working_fdt 0x41e8fe70 to 0x41e6fe70
[01.595]## error: update_fdt_dram_para : FDT_ERR_NOTFOUND
[01.604]update dts
Hit any key to stop autoboot:  0 
input addr exceed dram scope
[03.035]no vendor_boot partition is found
Android's image name: v851se-perf1
[03.098]Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.191 (tanlining@ubuntu) (gcc version 6.4.1 (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) ) #3 PREEMPT Fri Feb 17 11:57:27 UTC 2023
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt:Machine model: sun8iw21
[    0.000000] disp reserve base 0x41f13000 ,size 0x384000
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat c0a4ecc8, node_mem_map c3f78000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: ubi.mtd=sys earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=ubi0_4 rootfstype=ubifs, rw init=/pseudo_init partitions=mbr@ubi0_0:boot-res@ubi0_1:env@ubi0_2:boot@ubi0_3:rootfs@ubi0_4:rootfs_data@ubi0_5:UDISK@ubi0_6: cma= snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.hardware=sun8iw21p1 boot_type=5 androidboot.boot_type=5 gpt=1 uboot_message=2018.05-ga697d75(07/28/2022-05:29:47) mbr_offset=1032192 disp_reserve=3686400,0x41f13000 bootreason=button aw-ubi-spinand.ubootblks=24 androidboot.dramsize=64 
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 51112K/65536K available (6144K kernel code, 318K rwdata, 1368K rodata, 1024K init, 167K bss, 14424K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc4800000 - 0xff800000   ( 944 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0700000   (7136 kB)
[    0.000000]       .init : 0xc0900000 - 0xc0a00000   (1024 kB)
[    0.000000]       .data : 0xc0a00000 - 0xc0a4fb88   ( 319 kB)
[    0.000000]        .bss : 0xc0a4fb88 - 0xc0a79948   ( 168 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] sunxi_parse_sdm_info failed: -1
[    0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000000] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000023] Switching to timer-based delay loop, resolution 41ns
[    0.000203] Console: colour dummy device 80x30
[    0.000235] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.000251] pid_max: default: 32768 minimum: 301
[    0.000455] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000468] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001063] CPU: Testing write buffer coherency: ok
[    0.001697] Setting up static identity map for 0x40100000 - 0x40100058
[    0.003443] devtmpfs: initialized
[    0.038833] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.039483] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.039519] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.039670] atomic64_test: passed
[    0.039685] pinctrl core: initialized pinctrl subsystem
[    0.040814] NET: Registered protocol family 16
[    0.041591] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.043001] dump_class_init,857, success
[    0.069499] cpuidle: using governor menu
[    0.070860] platform 2010000.iommu: iova_base: 0x48400000
[    0.071446] sunxi iommu: irq = 22
[    0.093083] sun8iw21p1-pinctrl pio: initialized sunXi PIO driver
[    0.096254] iommu: Adding device npu to group 0
[    0.098404] iommu: Adding device 1c0e000.ve to group 0
[    0.112094] iommu: Adding device 5410000.g2d to group 0
[    0.113230] iommu: Adding device 5000000.disp to group 0
[    0.125014] iommu: Adding device 5908000.tdm to group 0
[    0.125772] iommu: Adding device 5900000.isp to group 0
[    0.126820] iommu: Adding device 58ffffc.isp to group 0
[    0.127800] iommu: Adding device 58ffff8.isp to group 0
[    0.128560] iommu: Adding device 58ffff4.isp to group 0
[    0.129203] iommu: Adding device 5800800.vind:isp@4 to group 0
[    0.130660] iommu: Adding device 5910000.scaler to group 0
[    0.131353] iommu: Adding device 590fffc.scaler to group 0
[    0.131966] iommu: Adding device 590fff8.scaler to group 0
[    0.132602] iommu: Adding device 590fff4.scaler to group 0
[    0.133349] iommu: Adding device 5910400.scaler to group 0
[    0.134022] iommu: Adding device 59103fc.scaler to group 0
[    0.134665] iommu: Adding device 59103f8.scaler to group 0
[    0.135352] iommu: Adding device 59103f4.scaler to group 0
[    0.136265] iommu: Adding device 5910800.scaler to group 0
[    0.136902] iommu: Adding device 59107fc.scaler to group 0
[    0.137501] iommu: Adding device 59107f8.scaler to group 0
[    0.138127] iommu: Adding device 59107f4.scaler to group 0
[    0.138846] iommu: Adding device 5910c00.scaler to group 0
[    0.139518] iommu: Adding device 5910bfc.scaler to group 0
[    0.140419] iommu: Adding device 5910bf8.scaler to group 0
[    0.141103] iommu: Adding device 5910bf4.scaler to group 0
[    0.142506] iommu: Adding device vinc0 to group 0
[    0.143429] iommu: Adding device vinc4 to group 0
[    0.144330] iommu: Adding device vinc8 to group 0
[    0.145241] iommu: Adding device vinc12 to group 0
[    0.189219] pwm module init!
[    0.198012] sunxi-pm debug v3.10
[    0.199817] SCSI subsystem initialized
[    0.201037] usbcore: registered new interface driver usbfs
[    0.201272] usbcore: registered new interface driver hub
[    0.201459] usbcore: registered new device driver usb
[    0.202023] sunxi_i2c_adap_init()2748 - init
[    0.202560] sunxi_i2c_probe()2443 - [i2c1] twi_drv_used = 0
[    0.202579] sunxi_i2c_probe()2450 - [i2c1] twi_pkt_interval = 0
[    0.202648] twi_regulator_request()647 - [i2c1] regulator not found(isn't configured in dts)!
[    0.202657] twi_request_gpio()463 - [i2c1] init name: (null)
[    0.204878] media: Linux media interface: v0.10
[    0.205100] Linux video capture interface: v2.00
[    0.206843] ion_parse_dt_heap_common: id 0 type 0 name sys_user align 1000
[    0.207254] ion_parse_dt_heap_common: id 4 type 4 name cma align 1000
[    0.209172] Advanced Linux Sound Architecture Driver Initialized.
[    0.210969] Bluetooth: Core ver 2.22
[    0.211173] NET: Registered protocol family 31
[    0.211186] Bluetooth: HCI device and connection manager initialized
[    0.211214] Bluetooth: HCI socket layer initialized
[    0.211229] Bluetooth: L2CAP socket layer initialized
[    0.211292] Bluetooth: SCO socket layer initialized
[    0.214227] clocksource: Switched to clocksource arch_sys_counter
[    0.247625] get androidboot.mode fail
[    0.250034] NET: Registered protocol family 2
[    0.264618] TCP established hash table entries: 16 (order: -6, 64 bytes)
[    0.264640] TCP bind hash table entries: 16 (order: -6, 64 bytes)
[    0.264650] TCP: Hash tables configured (established 16 bind 16)
[    0.264727] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.264753] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.265000] NET: Registered protocol family 1
[    0.265346] sun8iw21p1-pinctrl pio: can not get func[mux=7] on pin PC0
[    0.265366] sun8iw21p1-pinctrl pio: can not get func[mux=7] on pin PC1
[    0.265381] sun8iw21p1-pinctrl pio: can not get func[mux=7] on pin PC2
[    0.265395] sun8iw21p1-pinctrl pio: can not get func[mux=7] on pin PC3
[    0.265409] sun8iw21p1-pinctrl pio: can not get func[mux=7] on pin PC4
[    0.265424] sun8iw21p1-pinctrl pio: can not get func[mux=7] on pin PC5
[    0.265710] sunxi_spi_probe()2250 - [spi0] SPI DBI INTERFACE
[    0.265723] sunxi_spi_probe()2259 - [spi0] SPI MASTER MODE
[    0.265803] sunxi_spi_resource_get()1917 - sample_mode:1 sample_delay:12
[    0.265827] spi0 supply spi not found, using dummy regulator
[    0.265921] sunxi_spi_request_gpio()1883 - [spi0] Pinctrl init spi0
[    0.266015] sunxi_spi_clk_init()1954 - [spi0] mclk 100000000
[    0.267243] sunxi_spi_probe()2339 - [spi0]: driver probe succeed, base c4868000, irq 294
[    0.271741] sunxi_sid_driver_init+0x0/0x10 complete comp.
[    0.273077] workingset: timestamp_bits=29 max_order=14 bucket_order=0
[    0.291491] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.292100] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.295217] io scheduler noop registered
[    0.295237] io scheduler deadline registered
[    0.295583] io scheduler cfq registered (default)
[    0.296922] [DISP]disp_module_init
[    0.298526] [DISP] parser_disp_init_para,line:1306:
[    0.298541] of_property_read disp_init.disp_init_enable fail
[    0.299095] lcd 0, driver_name ,  panel_name default_lcd
[    0.299111] lcd 0, driver_name ,  panel_name he0801a068
[    0.299119] lcd 0, driver_name ,  panel_name inet_dsi_panel
[    0.299127] lcd 0, driver_name ,  panel_name lq101r1sx03
[    0.299134] lcd 0, driver_name ,  panel_name WilliamLcd
[    0.299142] lcd 0, driver_name ,  panel_name bp101wx1
[    0.299150] lcd 0, driver_name ,  panel_name k101im2qa04
[    0.299157] lcd 0, driver_name ,  panel_name t050k589
[    0.299165] lcd 0, driver_name ,  panel_name kd080d24
[    0.299172] lcd 0, driver_name ,  panel_name super_lcd_driver
[    0.300570] [DISP]disp_module_init finish
[    0.303992] uart0 supply uart not found, using dummy regulator
[    0.305072] uart0: ttyS0 at MMIO 0x2500000 (irq = 289, base_baud = 1500000) is a SUNXI
[    0.305113] sw_console_setup()2050 - console setup baud 115200 parity n bits 8, flow n
[    1.413479] console [ttyS0] enabled
[    1.418461] misc dump reg init
[    1.423333] sunxi-wlan soc@03000000:wlan@0: wlan_busnum (1)
[    1.429927] sunxi-wlan soc@03000000:wlan@0: wlan_power_num (-1)
[    1.436655] sunxi-wlan soc@03000000:wlan@0: Missing wlan_io_regulator.
[    1.443992] sunxi-wlan soc@03000000:wlan@0: io_regulator_name ((null))
[    1.451450] sunxi-wlan soc@03000000:wlan@0: request pincrtl handle for device [soc@03000000:wlan@0] failed
[    1.462404] sunxi-wlan soc@03000000:wlan@0: wlan_regon gpio=134  mul-sel=1  pull=1  drv_level=2  data=0
[    1.473045] sunxi-wlan soc@03000000:wlan@0: get gpio chip_en failed
[    1.480132] sunxi-wlan soc@03000000:wlan@0: wlan_hostwake gpio=135  mul-sel=14  pull=1  drv_level=2  data=0
[    1.491219] sunxi-wlan soc@03000000:wlan@0: clk_name ()
[    1.498822] sunxi-spinand: AW SPINand MTD Layer Version: 2.4 20220106
[    1.506567] sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.11 20211125
[    1.514532] sunxi-spinand-phy: detect munufacture from id table: Mxic
[    1.521773] sunxi-spinand-phy: detect spinand id: ffff12c2 ffffffff
[    1.528864] sunxi-spinand-phy: ========== arch info ==========
[    1.535541] sunxi-spinand-phy: Model:               MX35LF1GE4AB
[    1.542290] sunxi-spinand-phy: Munufacture:         Mxic
[    1.548292] sunxi-spinand-phy: DieCntPerChip:       1
[    1.553965] sunxi-spinand-phy: BlkCntPerDie:        1024
[    1.559957] sunxi-spinand-phy: PageCntPerBlk:       64
[    1.565740] sunxi-spinand-phy: SectCntPerPage:      4
[    1.571412] sunxi-spinand-phy: OobSizePerPage:      64
[    1.577190] sunxi-spinand-phy: BadBlockFlag:        0x1
[    1.583056] sunxi-spinand-phy: OperationOpt:        0x7
[    1.588931] sunxi-spinand-phy: MaxEraseTimes:       65000
[    1.595004] sunxi-spinand-phy: EccFlag:             0x2
[    1.600869] sunxi-spinand-phy: EccType:             4
[    1.606551] sunxi-spinand-phy: EccProtectedType:    3
[    1.612222] sunxi-spinand-phy: ========================================
[    1.619660] sunxi-spinand-phy: 
[    1.623184] sunxi-spinand-phy: ========== physical info ==========
[    1.630134] sunxi-spinand-phy: TotalSize:    128 M
[    1.635522] sunxi-spinand-phy: SectorSize:   512 B
[    1.640901] sunxi-spinand-phy: PageSize:     2 K
[    1.646094] sunxi-spinand-phy: BlockSize:    128 K
[    1.651473] sunxi-spinand-phy: OOBSize:      64 B
[    1.656763] sunxi-spinand-phy: ========================================
[    1.664192] sunxi-spinand-phy: 
[    1.667725] sunxi-spinand-phy: ========== logical info ==========
[    1.674578] sunxi-spinand-phy: TotalSize:    128 M
[    1.679957] sunxi-spinand-phy: SectorSize:   512 B
[    1.685345] sunxi-spinand-phy: PageSize:     4 K
[    1.690529] sunxi-spinand-phy: BlockSize:    256 K
[    1.695916] sunxi-spinand-phy: OOBSize:      128 B
[    1.701294] sunxi-spinand-phy: ========================================
[    1.708817] sunxi-spinand-phy: block lock register: 0x00
[    1.714891] sunxi-spinand-phy: feature register: 0x11
[    1.720568] sunxi-spinand-phy: sunxi physic nand init end
[    1.728866] sunxipart: failed to parse sunxi_gpt!
[    1.734176] Creating 4 MTD partitions on "sunxi_mtd_nand":
[    1.740433] 0x000000000000-0x000000100000 : "boot0"
[    1.749413] 0x000000100000-0x000000400000 : "uboot"
[    1.757153] random: fast init done
[    1.765135] 0x000000400000-0x000000500000 : "secure_storage"
[    1.775318] 0x000000500000-0x000008000000 : "sys"
[    1.996715] random: crng init done
[    2.082572] libphy: Fixed MDIO Bus: probed
[    2.088741] sunxi gmac driver's version: 2.0.2
[    2.096309] Failed to alloc md5
[    2.099857] eth0: Use random mac address
[    2.104817] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.112581] get ehci0-controller, regulator_io is no nocare
[    2.119246] get ehci0-controller wakeup-source is fail.
[    2.125405] sunxi ehci0-controller don't init wakeup source
[    2.131679] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xc0a6eeb0, 0x:c4879000, irq_no:130
[    2.143930] [sunxi-ehci0]: Not init ehci0
[    2.148974] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.156567] get ohci0-controller, regulator_io is no nocare
[    2.162833] get ohci0-controller wakeup-source is fail.
[    2.168978] sunxi ohci0-controller don't init wakeup source
[    2.175421] [sunxi-ohci0]: probe, pdev->name: 4101000.ohci0-controller, sunxi_ohci: 0xc0a6f0d4
[    2.185185] [sunxi-ohci0]: Not init ohci0
[    2.190361] usbcore: registered new interface driver uas
[    2.196850] usbcore: registered new interface driver usb-storage
[    2.203901] usbcore: registered new interface driver ums-alauda
[    2.210825] usbcore: registered new interface driver ums-cypress
[    2.217923] usbcore: registered new interface driver ums-datafab
[    2.225102] usbcore: registered new interface driver ums_eneub6250
[    2.232336] usbcore: registered new interface driver ums-freecom
[    2.239366] usbcore: registered new interface driver ums-isd200
[    2.246387] usbcore: registered new interface driver ums-jumpshot
[    2.253543] usbcore: registered new interface driver ums-karma
[    2.260436] usbcore: registered new interface driver ums-onetouch
[    2.267722] usbcore: registered new interface driver ums-realtek
[    2.274834] usbcore: registered new interface driver ums-sddr09
[    2.281784] usbcore: registered new interface driver ums-sddr55
[    2.288714] usbcore: registered new interface driver ums-usbat
[    2.295578] usb_serial_number:20080411
[    2.300730] sunxi_gpadc_init,1949, success
[    2.306221] sunxi_gpadc_setup: get channel scan data failed
[    2.313764] input: sunxi-gpadc0 as /devices/virtual/input/input0
[    2.323210] sunxi-rtc rtc: rtc core: registered sunxi-rtc as rtc0
[    2.330486] sunxi-rtc rtc: RTC enabled
[    2.334925] fix to cold boot, save boot reason
[    2.340332] i2c /dev entries driver
[    2.345084] sunxi cedar version 0.1
[    2.349162] VE: install start!!!
[    2.349162] 
[    2.354891] VE: cedar-ve the get irq is 291
[    2.359702] VE: regs_csi = c48a3000
[    2.364392] VE: get debugfs_mpp_root is NULL, please check mpp
[    2.364392] 
[    2.372618] VE: sunxi ve debug register driver failed, maybe ok, please check
[    2.372618] 
[    2.382554] VE: ve_proc_mgr: flag = 1
[    2.382554] 
[    2.388439] VE: install end!!!
[    2.388439] 
[    2.394010] google_vp9: sunxi google vp9 version 0.1
[    2.403109] sunxi-wdt 20500a0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    2.412863] Bluetooth: HCI UART driver ver 2.2.d448471.20181218-163903
[    2.420423] Bluetooth: HCI UART protocol H4 registered
[    2.426340] Bluetooth: HCI H4 protocol initialized
[    2.431977] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 01.00.07
[    2.439849] bt_fdi debugfs_init
[    2.448003] cpuidle: enable-method property 'psci' found operations
[    2.457969] sunxi-mmc sdc0: SD/MMC/SDIO Host Controller Driver(v3.59 2022-4-21 13:40)
[    2.467505] sunxi-mmc sdc0: ***ctl-spec-caps*** 8
[    2.472848] sunxi-mmc sdc0: No vmmc regulator found
[    2.478467] sunxi-mmc sdc0: No vqmmc regulator found
[    2.484048] sunxi-mmc sdc0: No vdmmc regulator found
[    2.489677] sunxi-mmc sdc0: No vd33sw regulator found
[    2.495441] sunxi-mmc sdc0: No vd18sw regulator found
[    2.501118] sunxi-mmc sdc0: No vq33sw regulator found
[    2.506830] sunxi-mmc sdc0: No vq18sw regulator found
[    2.513042] sunxi-mmc sdc0: set host busy
[    2.517742] sunxi-mmc sdc0: Got CD GPIO
[    2.522577] sunxi-mmc sdc0: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.533089] sunxi-mmc sdc0: no vqmmc,Check if there is regulator
[    2.564257] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.604502] sunxi-mmc sdc0: detmode:gpio irq
[    2.609591] sun8iw21p1-pinctrl pio: expect_func as:io_disabled, but muxsel(7) is func:uart3
[    2.619044] sun8iw21p1-pinctrl pio: expect_func as:io_disabled, but muxsel(7) is func:uart3
[    2.628452] sun8iw21p1-pinctrl pio: expect_func as:io_disabled, but muxsel(7) is func:uart3
[    2.637856] sun8iw21p1-pinctrl pio: expect_func as:io_disabled, but muxsel(7) is func:uart3
[    2.647258] sun8iw21p1-pinctrl pio: expect_func as:io_disabled, but muxsel(7) is func:uart3
[    2.656672] sun8iw21p1-pinctrl pio: expect_func as:io_disabled, but muxsel(7) is func:uart3
[    2.666341] sunxi-mmc sdc1: SD/MMC/SDIO Host Controller Driver(v3.59 2022-4-21 13:40)
[    2.675346] sunxi-mmc sdc1: ***ctl-spec-caps*** 8
[    2.680680] sunxi-mmc sdc1: No vmmc regulator found
[    2.686198] sunxi-mmc sdc1: No vqmmc regulator found
[    2.691777] sunxi-mmc sdc1: No vdmmc regulator found
[    2.697368] sunxi-mmc sdc1: No vd33sw regulator found
[    2.703043] sunxi-mmc sdc1: No vd18sw regulator found
[    2.708729] sunxi-mmc sdc1: No vq33sw regulator found
[    2.714416] sunxi-mmc sdc1: No vq18sw regulator found
[    2.720667] sunxi-mmc sdc1: set host busy
[    2.725309] mmc:failed to get gpios
[    2.729670] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.740167] sunxi-mmc sdc1: no vqmmc,Check if there is regulator
[    2.774257] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.814293] sunxi-mmc sdc0: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    2.824605] sunxi-mmc sdc1: detmode:manually by software
[    2.826238] usbcore: registered new interface driver usbhid
[    2.826242] usbhid: USB HID core driver
[    2.830324] [sound 1158][DAUDIO snd_sunxi_regulator_init] regulator missing or invalid
[    2.832449] sunxi-snd-mach soc@03000000:codec_mach: sunxi-snd-codec <-> soc@03000000:codec_plat mapping ok
[    2.835565] sunxi-snd-mach soc@03000000:daudio0_mach: snd-soc-dummy-dai <-> 2032000.daudio0_plat mapping ok
[    2.851758] NET: Registered protocol family 10
[    2.854072] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    2.855767] NET: Registered protocol family 17
[    2.855809] NET: Registered protocol family 15
[    2.856149] Bluetooth: RFCOMM TTY layer initialized
[    2.856171] Bluetooth: RFCOMM socket layer initialized
[    2.856200] Bluetooth: RFCOMM ver 1.11
[    2.857545] Registering SWP/SWPB emulation handler
[    2.945898] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[    2.952546] ubi0: attaching mtd3
[    2.956258] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[    2.956322] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.964618] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.976528] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    2.987381] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    2.993305] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    2.999208] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    2.999239] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    3.000326] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.000400] sunxi-mmc sdc1: no vqmmc,Check if there is regulator
[    3.032769] sunxi-mmc sdc1: sdc set ios:clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.055390] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[    3.062477] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[    3.068518] sunxi-mmc sdc1: sdc set ios:clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.082955] sunxi-mmc sdc1: sdc set ios:clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.096979] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    3.103958] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    3.110985] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    3.117992] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    3.123908] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    3.135952] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.146912] sunxi-mmc sdc1: no vqmmc,Check if there is regulator
[    3.174274] sunxi-mmc sdc1: sdc set ios:clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.215876] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[    3.223496] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[    3.229526] sunxi-mmc sdc1: sdc set ios:clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.244146] sunxi-mmc sdc1: sdc set ios:clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.258530] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    3.266079] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    3.273595] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    3.281135] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    3.287066] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    3.298988] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.310183] sunxi-mmc sdc1: no vqmmc,Check if there is regulator
[    3.344266] sunxi-mmc sdc1: sdc set ios:clk 100000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.387486] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[    3.396701] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[    3.402724] sunxi-mmc sdc1: sdc set ios:clk 100000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.417968] sunxi-mmc sdc1: sdc set ios:clk 100000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.433910] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    3.443067] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    3.452224] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    3.461407] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[    3.467361] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    3.536495] ubi0: scanning is finished
[    3.551714] ubi0: attached mtd3 (name "sys", size 123 MiB)
[    3.558002] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[    3.565775] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[    3.573404] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    3.581372] ubi0: good PEBs: 492, bad PEBs: 0, corrupted PEBs: 0
[    3.588171] ubi0: user volume: 7, internal volumes: 1, max. volumes count: 128
[    3.596336] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
[    3.605751] ubi0: available PEBs: 10, total reserved PEBs: 482, PEBs reserved for bad PEB handling: 10
[    3.616234] ubi0: background thread "ubi_bgt0d" started, PID 693
[    3.623562] get det_vbus is fail, 84
[    3.627794] get id is fail, 84
[    3.632325] sunxi-rtc rtc: setting system clock to 1970-01-01 00:00:07 UTC (7)
[    3.641602] clk: Not disabling unused clocks
[    3.646529] ALSA device list:
[    3.649863]   #0: audiocodec
[    3.653110]   #1: snddaudio0
[    3.660272] List of all partitions:
[    3.664574] 1f00            1024 mtdblock0  (driver?)
[    3.670267] 1f01            3072 mtdblock1  (driver?)
[    3.676025] 1f02            1024 mtdblock2  (driver?)
[    3.681705] 1f03          125952 mtdblock3  (driver?)
[    3.687531] No filesystem could mount root, tried:  ubifs
[    3.693611] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    3.702903] CPU: 0 PID: 1 Comm: swapper Not tainted 4.9.191 #3
[    3.709451] Hardware name: sun8iw21
[    3.713401] [<c010d3cc>] (unwind_backtrace) from [<c010a51c>] (show_stack+0x10/0x14)
[    3.722112] [<c010a51c>] (show_stack) from [<c016ff58>] (panic+0xac/0x2b0)
[    3.729846] [<c016ff58>] (panic) from [<c0901270>] (mount_block_root+0x208/0x2f4)
[    3.738260] [<c0901270>] (mount_block_root) from [<c0901450>] (prepare_namespace+0x84/0x178)
[    3.747747] [<c0901450>] (prepare_namespace) from [<c0900e80>] (kernel_init_freeable+0x11c/0x178)
[    3.757724] [<c0900e80>] (kernel_init_freeable) from [<c0649f90>] (kernel_init+0x8/0x108)
[    3.766921] [<c0649f90>] (kernel_init) from [<c0106ca8>] (ret_from_fork+0x14/0x2c)
[    3.775432] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    3.785593] sunxi dump enabled
[    3.789017] dump regs done
[    3.792091] flush cache done
[    3.795341] crashdump enter

哪位大神知道是什么问题，帮忙指点迷津，谢谢。

[WhycanService]

[ 1.612222] sunxi-spinand-phy: ========================================
[ 1.619660] sunxi-spinand-phy:
[ 1.623184] sunxi-spinand-phy: ========== physical info ==========
[ 1.630134] sunxi-spinand-phy: TotalSize: 128 M
[ 1.635522] sunxi-spinand-phy: SectorSize: 512 B
[ 1.640901] sunxi-spinand-phy: PageSize: 2 K
[ 1.646094] sunxi-spinand-phy: BlockSize: 128 K
[ 1.651473] sunxi-spinand-phy: OOBSize: 64 B
[ 1.656763] sunxi-spinand-phy: ========================================
[ 1.664192] sunxi-spinand-phy:
[ 1.667725] sunxi-spinand-phy: ========== logical info ==========
[ 1.674578] sunxi-spinand-phy: TotalSize: 128 M
[ 1.679957] sunxi-spinand-phy: SectorSize: 512 B
[ 1.685345] sunxi-spinand-phy: PageSize: 4 K
[ 1.690529] sunxi-spinand-phy: BlockSize: 256 K
[ 1.695916] sunxi-spinand-phy: OOBSize: 128 B
[ 1.701294] sunxi-spinand-phy: ========================================
[ 1.708817] sunxi-spinand-phy: block lock register: 0x00
[ 1.714891] sunxi-spinand-phy: feature register: 0x11
[ 1.720568] sunxi-spinand-phy: sunxi physic nand init end
[ 1.728866] sunxipart: failed to parse sunxi_gpt!
[ 1.734176] Creating 4 MTD partitions on "sunxi_mtd_nand":
[ 1.740433] 0x000000000000-0x000000100000 : "boot0"
[ 1.749413] 0x000000100000-0x000000400000 : "uboot"
[ 1.757153] random: fast init done
[ 1.765135] 0x000000400000-0x000000500000 : "secure_storage"
[ 1.775318] 0x000000500000-0x000008000000 : "sys"

nand 识别到了，但是没有ubifs的配置层

[ 3.660272] List of all partitions:
[ 3.664574] 1f00 1024 mtdblock0 (driver?)
[ 3.670267] 1f01 3072 mtdblock1 (driver?)
[ 3.676025] 1f02 1024 mtdblock2 (driver?)
[ 3.681705] 1f03 125952 mtdblock3 (driver?)
[ 3.687531] No filesystem could mount root, tried: ubifs

[WhycanService]

# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SYSVIPC=y
# CONFIG_FHANDLE is not set
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
# CONFIG_SYSFS_SYSCALL is not set
# CONFIG_AIO is not set
CONFIG_EMBEDDED=y
# CONFIG_SLUB_DEBUG is not set
# CONFIG_COMPAT_BRK is not set
CONFIG_JUMP_LABEL=y
CONFIG_CC_STACKPROTECTOR_REGULAR=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_BLK_DEV_BSG is not set
CONFIG_ARCH_SUNXI=y
CONFIG_ARCH_SUN8IW21=y
CONFIG_EVB_PLATFORM=y
CONFIG_SUNXI_SOC_NAME="sun8iw21"
CONFIG_SWP_EMULATE=y
# CONFIG_VDSO is not set
CONFIG_ARM_PSCI=y
CONFIG_PREEMPT=y
CONFIG_AEABI=y
CONFIG_OABI_COMPAT=y
CONFIG_HIGHMEM=y
# CONFIG_COMPACTION is not set
CONFIG_CMA=y
CONFIG_ARM_FLUSH_CONSOLE_ON_RESTART=y
CONFIG_USE_OF=y
# CONFIG_ATAGS is not set
CONFIG_CMDLINE="earlyprintk=sunxi-uart,0x05000000 loglevel=8 initcall_debug=1 console=ttyS0 init=/init"
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
CONFIG_CPU_FREQ_GOV_INTERACTIVE=y
CONFIG_CPUFREQ_DT=y
CONFIG_ARM_ALLWINNER_SUN50I_CPUFREQ_NVMEM=y
CONFIG_CPU_IDLE=y
CONFIG_ARM_CPUIDLE=y
CONFIG_SUNXI_CPU0IDLE=y
CONFIG_VFP=y
CONFIG_NEON=y
# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
CONFIG_PM_WAKELOCKS=y
CONFIG_PM_DEBUG=y
CONFIG_PM_ADVANCED_DEBUG=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_PACKET_DIAG=y
CONFIG_UNIX=y
CONFIG_UNIX_DIAG=y
CONFIG_NET_KEY=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_IP_PING=y
CONFIG_IP_FIB_TRIE_STATS=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_VERBOSE=y
CONFIG_IP_MROUTE=y
CONFIG_IP_MROUTE_MULTIPLE_TABLES=y
CONFIG_IPV6_MULTIPLE_TABLES=y
CONFIG_IPV6_SUBTREES=y
CONFIG_IPV6_MROUTE=y
CONFIG_BT=y
CONFIG_BT_RFCOMM=y
CONFIG_BT_RFCOMM_TTY=y
# CONFIG_BT_HS is not set
# CONFIG_BT_LE is not set
CONFIG_XR_BT_LPM=y
CONFIG_XR_BT_FDI=y
CONFIG_BT_HCIUART=y
CONFIG_BT_HCIUART_H4=y
CONFIG_HFP_OVER_PCM=y
CONFIG_CFG80211=y
CONFIG_RFKILL=y
CONFIG_RFKILL_GPIO=y
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_DEVTMPFS=y
CONFIG_DEVTMPFS_MOUNT=y
CONFIG_SUNXI_MBUS=y
CONFIG_MTD=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_CFI=y
CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_CFI_AMDSTD=y
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP_OF=y
CONFIG_MTD_NAND_IDS=y
CONFIG_AW_MTD_SPINAND=y
CONFIG_MTD_UBI_BLOCK=y
CONFIG_SUNXI_RFKILL=y
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_NETDEVICES=y
CONFIG_SUNXI_GMAC=y
CONFIG_NET_VENDOR_AURORA=y
# CONFIG_USB_NET_DRIVERS is not set
# CONFIG_WLAN_VENDOR_ADMTEK is not set
# CONFIG_WLAN_VENDOR_ATH is not set
# CONFIG_WLAN_VENDOR_ATMEL is not set
# CONFIG_WLAN_VENDOR_BROADCOM is not set
# CONFIG_WLAN_VENDOR_CISCO is not set
# CONFIG_WLAN_VENDOR_INTEL is not set
# CONFIG_WLAN_VENDOR_INTERSIL is not set
# CONFIG_WLAN_VENDOR_MARVELL is not set
# CONFIG_WLAN_VENDOR_MEDIATEK is not set
# CONFIG_WLAN_VENDOR_RALINK is not set
# CONFIG_WLAN_VENDOR_REALTEK is not set
# CONFIG_WLAN_VENDOR_RSI is not set
# CONFIG_WLAN_VENDOR_ST is not set
# CONFIG_WLAN_VENDOR_TI is not set
# CONFIG_WLAN_VENDOR_ZYDAS is not set
CONFIG_XR829_WLAN=m
CONFIG_ISDN=y
# CONFIG_INPUT_MOUSEDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_SENSORINIT is not set
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
CONFIG_INPUT_TOUCHSCREEN=y
# CONFIG_TOUCHSCREEN_PROPERTIES is not set
CONFIG_TOUCHSCREEN_FT6236=y
# CONFIG_TOUCHSCREEN_GT82X is not set
# CONFIG_TOUCHSCREEN_IT7257_TS is not set
# CONFIG_TOUCHSCREEN_GSLX680NEW is not set
# CONFIG_TOUCHSCREEN_FT5X16_TS is not set
# CONFIG_TOUCHSCREEN_GT9XX_TS is not set
# CONFIG_TOUCHSCREEN_TLSC6X_TS is not set
CONFIG_INPUT_MISC=y
CONFIG_SUNXI_WIEGAND=y
CONFIG_INPUT_SENSOR=y
# CONFIG_SENSORS_BMA250 is not set
# CONFIG_SENSORS_SC7A30 is not set
# CONFIG_SENSORS_MMA7660 is not set
# CONFIG_SENSORS_MIR3DA is not set
# CONFIG_SENSORS_MXC622X is not set
# CONFIG_SENSORS_MMA8452 is not set
# CONFIG_SENSORS_MMA865X is not set
# CONFIG_SENSORS_MC32X0 is not set
CONFIG_SENSORS_GPADC=y
CONFIG_KEY_GPIO=y
# CONFIG_SENSORS_DA380 is not set
# CONFIG_SERIO is not set
# CONFIG_LEGACY_PTYS is not set
# CONFIG_DEVMEM is not set
# CONFIG_DEVKMEM is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_SUNXI_SYS_INFO is not set
CONFIG_SUNXI_G2D=y
CONFIG_SUNXI_G2D_MIXER=y
CONFIG_SUNXI_G2D_ROTATE=y
CONFIG_SUNXI_NNA_VIP=y
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_SUNXI=y
CONFIG_SPI=y
CONFIG_SPI_SUNXI=y
CONFIG_GPIOLIB=y
CONFIG_GPIO_SYSFS=y
CONFIG_POWER_SUPPLY=y
CONFIG_AXP2101_POWER=y
CONFIG_THERMAL=y
CONFIG_THERMAL_GOV_USER_SPACE=y
CONFIG_THERMAL_GOV_POWER_ALLOCATOR=y
CONFIG_CPU_THERMAL=y
CONFIG_THERMAL_EMULATION=y
CONFIG_SUNXI_THERMAL_NG=y
CONFIG_WATCHDOG=y
CONFIG_SUNXI_WATCHDOG=y
CONFIG_MFD_AXP2101_I2C=y
CONFIG_MFD_SYSCON=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_REGULATOR_VIRTUAL_CONSUMER=y
CONFIG_REGULATOR_AXP2101=y
CONFIG_MEDIA_SUPPORT=y
CONFIG_MEDIA_CAMERA_SUPPORT=y
CONFIG_MEDIA_CONTROLLER=y
CONFIG_VIDEO_V4L2_SUBDEV_API=y
CONFIG_V4L_PLATFORM_DRIVERS=y
CONFIG_VIDEO_SUNXI_VIN=m
# CONFIG_CSI_CCI is not set
CONFIG_VIN_IOMMU=y
CONFIG_D3D=y
CONFIG_D3D_COMPRESS_EN=y
# CONFIG_WDR is not set
CONFIG_SENSOR_GC2053_MIPI=m
# CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set
CONFIG_FB=y
CONFIG_DISP2_SUNXI=y
CONFIG_SUNXI_DISP2_FB_HW_ROTATION_SUPPORT=y
CONFIG_DISP2_SUNXI_DEBUG=y
CONFIG_LCD_SUPPORT_D310T9362V1_MIPI=y
# CONFIG_LCD_SUPPORT_HE0801A068 is not set
# CONFIG_LCD_SUPPORT_WILLIAMLCD is not set
# CONFIG_LCD_SUPPORT_LQ101R1SX03 is not set
# CONFIG_LCD_SUPPORT_INET_DSI_PANEL is not set
# CONFIG_LCD_SUPPORT_BP101WX1_206 is not set
# CONFIG_LCD_SUPPORT_K101IM2QA04 is not set
# CONFIG_LCD_SUPPORT_T050K589 is not set
# CONFIG_LCD_SUPPORT_KD080D24 is not set
CONFIG_SOUND=y
CONFIG_SND=y
CONFIG_SND_SOC=y
CONFIG_SND_SOC_SUNXI_AAUDIO=y
CONFIG_SND_SOC_SUNXI_DAUDIO=y
CONFIG_SND_SOC_SUNXI_COMPONENTS=y
CONFIG_SND_SOC_SUNXI_RXSYNC=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_SUNXI_HCD=y
CONFIG_USB_SUNXI_HCI=y
CONFIG_USB_SUNXI_EHCI0=y
CONFIG_USB_SUNXI_EHCI1=y
CONFIG_USB_SUNXI_OHCI0=y
CONFIG_USB_SUNXI_OHCI1=y
CONFIG_USB_STORAGE=y
CONFIG_USB_STORAGE_REALTEK=y
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
CONFIG_USB_STORAGE_ALAUDA=y
CONFIG_USB_STORAGE_ONETOUCH=y
CONFIG_USB_STORAGE_KARMA=y
CONFIG_USB_STORAGE_CYPRESS_ATACB=y
CONFIG_USB_STORAGE_ENE_UB6250=y
CONFIG_USB_UAS=y
CONFIG_USB_GADGET=y
CONFIG_USB_SUNXI_UDC0=y
CONFIG_USB_CONFIGFS=y
CONFIG_USB_CONFIGFS_MASS_STORAGE=y
CONFIG_USB_CONFIGFS_F_FS=y
CONFIG_USB_CONFIGFS_UEVENT=y
CONFIG_USB_CONFIGFS_F_HID=y
CONFIG_USB_SUNXI_USB=y
CONFIG_USB_SUNXI_USB_MANAGER=y
CONFIG_USB_SUNXI_USB_DEBUG=y
CONFIG_USB_SUNXI_USB_ADB=y
CONFIG_MMC=y
CONFIG_MMC_SUNXI=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_SUNXI=y
CONFIG_SUNXI_BOOTUP_EXTEND=y
CONFIG_SUNXI_RTC_BOOTCOUNT=y
CONFIG_DMADEVICES=y
CONFIG_DMA_SUNXI=y
CONFIG_STAGING=y
CONFIG_ION=y
CONFIG_ION_SUNXI=y
# CONFIG_COMMON_CLK_DEBUG is not set
# CONFIG_ARM_ARCH_TIMER_EVTSTREAM is not set
CONFIG_MAILBOX=y
CONFIG_SUNXI_MBOX=y
CONFIG_SUNXI_RV32_STANBY=y
CONFIG_SUNXI_IOMMU=y
CONFIG_SUNXI_RPROC=y
CONFIG_SUNXI_MSGBOX=y
CONFIG_SUNXI_RPMSG_E907=y
CONFIG_SUNXI_RPMSG_SPEEDTEST=y
CONFIG_SUNXI_RPMSG_HEARBEAT=y
CONFIG_RPMSG_CTRL=y
CONFIG_RPMSG_NOTIFY=y
CONFIG_RPMSG_VIRTIO=y
CONFIG_PWM=y
CONFIG_PWM_SUNXI_GROUP=y
CONFIG_ANDROID=y
CONFIG_NVMEM=y
CONFIG_NVMEM_SUN50I_SID=y
CONFIG_SUNXI_MPP=y
CONFIG_EXT4_FS=y
# CONFIG_FILE_LOCKING is not set
# CONFIG_DNOTIFY is not set
# CONFIG_INOTIFY_USER is not set
CONFIG_OVERLAY_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_UTF8=y
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
CONFIG_JFFS2_FS=y
CONFIG_JFFS2_SUMMARY=y
CONFIG_JFFS2_FS_XATTR=y
# CONFIG_JFFS2_FS_POSIX_ACL is not set
# CONFIG_JFFS2_FS_SECURITY is not set
CONFIG_JFFS2_COMPRESSION_OPTIONS=y
# CONFIG_JFFS2_ZLIB is not set
CONFIG_UBIFS_FS=y
CONFIG_SQUASHFS=y
CONFIG_SQUASHFS_LZ4=y
CONFIG_SQUASHFS_LZO=y
CONFIG_SQUASHFS_XZ=y
CONFIG_SQUASHFS_ZSTD=y
# CONFIG_NETWORK_FILESYSTEMS is not set
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
CONFIG_PRINTK_TIME=y
CONFIG_FRAME_WARN=2048
CONFIG_DEBUG_FS=y
CONFIG_DEBUG_VM=y
# CONFIG_SCHED_DEBUG is not set
CONFIG_DEBUG_MUTEXES=y
CONFIG_STACKTRACE=y
# CONFIG_FTRACE is not set
CONFIG_ATOMIC64_SELFTEST=y
CONFIG_SUNXI_DUMP=y

[tanlining]

@whycanservice 麻烦帮忙看下哪里配错了或者漏配了谢谢！！！！

[WhycanService]

@tanlining 直接拿我的config替换吧

[tanlining]

@whycanservice 好的 我试一下

[away123456]

@tanlining 兄弟，这个问题你是怎么解决的呀，求助