上FS35QA002后Uboot没有识别

[jxzhb]

https://bbs.aw-ol.com/topic/257/d1-h-d1s-spi-nand-ddr支持列表/7
根据论坛提供的FLASH列表，换上FS35QA002后Uboot没有识别

U-Boot 2018.07-ge987def5 (Nov 07 2022 - 03:11:27 +0000) Allwinner Technology

[03.467]DRAM:  512 MiB
[03.471]Relocation Offset is: 1deea000
[03.492]secure enable bit: 0
can't support chip type 20480
[03.499]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
sunxi flash map init
SPI ALL:   ready
[03.529]flash init start
[03.531]workmode = 16,storage type = 0
try card 2
set card number 2
get card number 2
[03.539][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00
[03.547][mmc]: get sdc_type fail and use default host:tm4.
[03.572][mmc]: Is not Boot mode!
[03.575][mmc]: SUNXI SDMMC Controller Version:0x50310
[03.586][mmc]: ************Try SD card 2************
[03.591][mmc]: mmc 2 cmd timeout 100 status 100
[03.595][mmc]: smc 2 err, cmd 8,  RTO
[03.599][mmc]: mmc 2 close bus gating and reset
[03.604][mmc]: mmc 2 cmd timeout 100 status 100
[03.608][mmc]: smc 2 err, cmd 55,  RTO
[03.611][mmc]: mmc 2 close bus gating and reset
[03.616][mmc]: ************Try MMC card 2************
[03.624][mmc]: mmc 2 cmd timeout 100 status 100
[03.629][mmc]: smc 2 err, cmd 1,  RTO
[03.632][mmc]: mmc 2 close bus gating and reset
[03.636][mmc]: Card did not respond to voltage select!
[03.641][mmc]: ************SD/MMC 2 init error!************
[03.646][mmc]: mmc init product failed
MMC init failed
try emmc fail
[03.660]sunxi-spinand: AW SPINand MTD Layer Version: 1.8 20220106
[03.666]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.11 20211217
[03.714]sunxi-spinand-phy: request spi0 gpio ok
[03.718]sunxi-spinand-phy: request general tx dma channel ok!
[03.724]sunxi-spinand-phy: request general rx dma channel ok!
[03.729]sunxi-spinand-phy: set spic0 clk to 20 Mhz
[03.733]sunxi-spinand-phy: init spic0 clk ok
[03.737]sunxi-spinand-phy: detect munufacture from id table: Foresee
[03.751]sunxi-spinand-phy: get spi-nand Model from fdt fail
[03.756]sunxi-spinand-phy: get phy info from fdt fail
[03.761]sunxi-spinand-phy: not detect munufacture from fdt
[03.766]sunxi-spinand-phy: not detect any munufacture from id table
[03.780]sunxi-spinand-phy: get spi-nand Model from fdt fail
[03.785]sunxi-spinand-phy: get phy info from fdt fail
[03.789]sunxi-spinand-phy: not detect munufacture from fdt
[03.795]sunxi-spinand-phy: not match spinand: 7272cd00 cd7272cd
try nand fail
[03.851]unrecognized JEDEC id bytes: ff, cd, 72
try spinor fail
initcall sequence 000000005ff91068 failed at call 000000004200df02 (err=-1)
### ERROR ### Please RESET the board ###

求帮助