上FS35QA002后Uboot没有识别
-
https://bbs.aw-ol.com/topic/257/d1-h-d1s-spi-nand-ddr支持列表/7
根据论坛提供的FLASH列表,换上FS35QA002后Uboot没有识别U-Boot 2018.07-ge987def5 (Nov 07 2022 - 03:11:27 +0000) Allwinner Technology [03.467]DRAM: 512 MiB [03.471]Relocation Offset is: 1deea000 [03.492]secure enable bit: 0 can't support chip type 20480 [03.499]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz sunxi flash map init SPI ALL: ready [03.529]flash init start [03.531]workmode = 16,storage type = 0 try card 2 set card number 2 get card number 2 [03.539][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00 [03.547][mmc]: get sdc_type fail and use default host:tm4. [03.572][mmc]: Is not Boot mode! [03.575][mmc]: SUNXI SDMMC Controller Version:0x50310 [03.586][mmc]: ************Try SD card 2************ [03.591][mmc]: mmc 2 cmd timeout 100 status 100 [03.595][mmc]: smc 2 err, cmd 8, RTO [03.599][mmc]: mmc 2 close bus gating and reset [03.604][mmc]: mmc 2 cmd timeout 100 status 100 [03.608][mmc]: smc 2 err, cmd 55, RTO [03.611][mmc]: mmc 2 close bus gating and reset [03.616][mmc]: ************Try MMC card 2************ [03.624][mmc]: mmc 2 cmd timeout 100 status 100 [03.629][mmc]: smc 2 err, cmd 1, RTO [03.632][mmc]: mmc 2 close bus gating and reset [03.636][mmc]: Card did not respond to voltage select! [03.641][mmc]: ************SD/MMC 2 init error!************ [03.646][mmc]: mmc init product failed MMC init failed try emmc fail [03.660]sunxi-spinand: AW SPINand MTD Layer Version: 1.8 20220106 [03.666]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.11 20211217 [03.714]sunxi-spinand-phy: request spi0 gpio ok [03.718]sunxi-spinand-phy: request general tx dma channel ok! [03.724]sunxi-spinand-phy: request general rx dma channel ok! [03.729]sunxi-spinand-phy: set spic0 clk to 20 Mhz [03.733]sunxi-spinand-phy: init spic0 clk ok [03.737]sunxi-spinand-phy: detect munufacture from id table: Foresee [03.751]sunxi-spinand-phy: get spi-nand Model from fdt fail [03.756]sunxi-spinand-phy: get phy info from fdt fail [03.761]sunxi-spinand-phy: not detect munufacture from fdt [03.766]sunxi-spinand-phy: not detect any munufacture from id table [03.780]sunxi-spinand-phy: get spi-nand Model from fdt fail [03.785]sunxi-spinand-phy: get phy info from fdt fail [03.789]sunxi-spinand-phy: not detect munufacture from fdt [03.795]sunxi-spinand-phy: not match spinand: 7272cd00 cd7272cd try nand fail [03.851]unrecognized JEDEC id bytes: ff, cd, 72 try spinor fail initcall sequence 000000005ff91068 failed at call 000000004200df02 (err=-1) ### ERROR ### Please RESET the board ###
求帮助
Copyright © 2023 深圳全志在线有限公司 粤ICP备2021084185号 粤公网安备44030502007680号