烧录suit工具写flash卡在7%

[missdangerous]

是因为w25q256的硬件问题吗?

U-Boot 2018.05-g24521d6 (Feb 11 2022 - 08:52:39 +0000) Allwinner Technology

[07.535]DRAM:  64 MiB
[07.540]Relocation Offset is: 01ee7000
[07.565]secure enable bit: 0
[07.571]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
[07.577]flash init start
[07.579]workmode = 16,storage type = 0
try card 2
set card number 2
get card number 2
[07.587][mmc]: mmc driver ver uboot2018:2021-11-19 15:38:00
[07.597][mmc]: get sdc_type fail and use default host:tm4.
[07.627][mmc]: Is not Boot mode!
[07.630][mmc]: SUNXI SDMMC Controller Version:0x50310
[07.641][mmc]: ************Try SD card 2************
[07.646][mmc]: mmc 2 cmd timeout 100 status 100
[07.650][mmc]: smc 2 err, cmd 8,  RTO
[07.654][mmc]: mmc 2 close bus gating and reset
[07.659][mmc]: mmc 2 cmd timeout 100 status 100
[07.663][mmc]: smc 2 err, cmd 55,  RTO
[07.667][mmc]: mmc 2 close bus gating and reset
[07.671][mmc]: ************Try MMC card 2************
[07.680][mmc]: mmc 2 cmd timeout 100 status 100
[07.684][mmc]: smc 2 err, cmd 1,  RTO
[07.687][mmc]: mmc 2 close bus gating and reset
[07.692][mmc]: Card did not respond to voltage select!
[07.696][mmc]: ************SD/MMC 2 init error!************
[07.702][mmc]: mmc init product failed
MMC init failed
try emmc fail
[07.718]sunxi-spinand: AW SPINand MTD Layer Version: 1.5 20200407
[07.723]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.9 20200306
[07.784]sunxi-spinand-phy: request spi0 gpio ok
[07.788]sunxi-spinand-phy: request general tx dma channel ok!
[07.794]sunxi-spinand-phy: request general rx dma channel ok!
[07.799]sunxi-spinand-phy: set spic0 clk to 20 Mhz
[07.804]sunxi-spinand-phy: init spic0 clk ok
sspi->base_addr = 0x4025000, the SPI control register:
[VER] 0x4025000 = 0x00010001, [GCR] 0x4025004 = 0x00000083, [TCR] 0x4025008 = 0x00000184
[ICR] 0x4025010 = 0x00000f00, [ISR] 0x4025014 = 0x00000032, [FCR] 0x4025018 = 0x00200020
[FSR] 0x402501c = 0x00000000, [WCR] 0x4025020 = 0x00000000, [CCR] 0x4025024 = 0x00000002
[SDC] 0x4025028 = 0x00002000, [BCR] 0x4025030 = 0x00000000, [TCR] 0x4025034 = 0x00000000
[BCC] 0x4025038 = 0x00000000, [DMA] 0x4025088 = 0x000000e5

[07.849]sunxi-spinand-phy: detect munufacture from id table: Winbond
[07.865]sunxi-spinand-phy: get spi-nand Model from fdt fail
[07.870]sunxi-spinand-phy: get phy info from fdt fail
[07.875]sunxi-spinand-phy: not detect munufacture from fdt
[07.880]sunxi-spinand-phy: not detect any munufacture from id table
[07.896]sunxi-spinand-phy: get spi-nand Model from fdt fail
[07.901]sunxi-spinand-phy: get phy info from fdt fail
[07.906]sunxi-spinand-phy: not detect munufacture from fdt
[07.911]sunxi-spinand-phy: not match spinand: 1940 0
try nand fail
individual lock is enable
[07.985]spi sunxi_slave->max_hz:100000000 
SF: Detected w25q256 with page size 256 Bytes, erase size 64 KiB, total 32 MiB
[08.001]Loading Environment from SUNXI_FLASH... OK
[08.014]try to burn key
[08.018]out of usb burn from boot: not need burn key
[08.022]Net:   [08.023]No ethernet found.
Hit any key to stop autoboot:  0 
sunxi work mode=0x10
run usb efex
delay time 2500
weak:otg_phy_config
usb init ok
set address 0x10
set address 0x10 ok
SUNXI_EFEX_ERASE_TAG
erase_flag = 0x12
origin_erase_flag = 0x1
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
the 0 mbr table is ok
*************MBR DUMP***************
total mbr part 6

part[0] name      :boot-resource
part[0] classname :DISK
part[0] addrlo    :0x20
part[0] lenlo     :0x100
part[0] user_type :32768
part[0] keydata   :0
part[0] ro        :0

part[1] name      :env
part[1] classname :DISK
part[1] addrlo    :0x120
part[1] lenlo     :0x100
part[1] user_type :32768
part[1] keydata   :0
part[1] ro        :0

part[2] name      :env-redund
part[2] classname :DISK
part[2] addrlo    :0x220
part[2] lenlo     :0x100
part[2] user_type :32768
part[2] keydata   :0
part[2] ro        :0

part[3] name      :boot
part[3] classname :DISK
part[3] addrlo    :0x320
part[3] lenlo     :0x3c00
part[3] user_type :32768
part[3] keydata   :0
part[3] ro        :0

part[4] name      :rootfs
part[4] classname :DISK
part[4] addrlo    :0x3f20
part[4] lenlo     :0x2800
part[4] user_type :32768
part[4] keydata   :0
part[4] ro        :0

part[5] name      :UDISK
part[5] classname :DISK
part[5] addrlo    :0x6720
part[5] lenlo     :0x0
part[5] user_type :33024
part[5] keydata   :0
part[5] ro        :0

common1(partition3) need it, here is a weak func
total part: 7
mbr 0, 20, 8000
boot-resource 1, 100, 8000
env 2, 100, 8000
env-redund 3, 100, 8000
boot 4, 3c00, 8000
rootfs 5, 2800, 8000
UDISK 6, 0, 8100
need erase flash: 18
The Chip Erase size is: 32M ...
[59.989]get secure storage map err
[59.992]erase secure storage block 0 err
SUNXI_EFEX_MBR_TAG
mbr size = 0x4000
SF: write offset not multiple of erase size
write primary GPT success
spinor: skip backup GPT
[60.201]update partition map
GUID Partition Table Header signature is wrong: 0x74704370004B4447 != 0x5452415020494645
part_get_info_efi: *** ERROR: Invalid GPT ***
ERROR: attempting read past flash size 
*** ERROR: Can't read GPT header ***
part_get_info_efi: *** ERROR: Invalid Backup GPT ***
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
FEX_CMD_fes_verify_value, start 0x20, size high 0x0:low 0x14000
FEX_CMD_fes_verify_value 0x284071e4

[awwwwa]

@missdangerous 固件损坏，GUID 分区表损坏

[missdangerous]

@awwwwa 我用东山D1S的开发板能下载, 但是自己画的板子一直卡7%, 是不是我的SPI flash那有问题

[awwwwa]

卡7%是不是烧录成nand固件了，nor固件文件名会写nor

[missdangerous]

@awwwwa 谢谢,硬件有错误造成的