请教如何排查 linux kernel 启动卡主的问题
-
背景：我买了一块T113-S3的开发板，SD卡启动。用配套 img就能启动，我自己尝试打了一个img，但是内核启动到一半卡主了。
环境：
1、board.dts、sun8iw20p1.dtsi.dtsi 均拷贝自配套源码。
2、芯片T113-S3
3、SD卡启动
4、来自 T113-i 的linux，版本 5.4.61启动日志如下：
[30]HELLO! BOOT0 is starting! [33]BOOT0 commit : adaf1174cc [36]set pll start [42]periph0 has been enabled [45]set pll end [46][pmu]: bus read error [49]board init ok [51]ZQ value = 0x2f [53]get_pmu_exist() = -1 [55]ddr_efuse_type: 0xa [58]trefi:7.8ms [60][AUTO DEBUG] single rank and full DQ! [64]ddr_efuse_type: 0xa [66]trefi:7.8ms [69][AUTO DEBUG] rank 0 row = 13 [72][AUTO DEBUG] rank 0 bank = 8 [75][AUTO DEBUG] rank 0 page size = 2 KB [79]DRAM BOOT DRIVE INFO: V0.33 [82]DRAM CLK = 936 MHz [85]DRAM Type = 3 (2:DDR2,3:DDR3) [88]DRAMC read ODT off. [90]DRAM ODT value: 0x42. [93]ddr_efuse_type: 0xa [96]DRAM SIZE =128 M [98]dram_tpr4:0x0 [100]PLL_DDR_CTRL_REG:0xf8004d00 [103]DRAM_CLK_REG:0xc0000000 [106][TIMING DEBUG] MR2= 0x20 [114]DRAM simple test OK. [116]rtc standby flag is 0x0, super standby flag is 0x0 [121]dram size =128 [124]card no is 0 [126]sdcard 0 line count 4 [128][mmc]: mmc driver ver 2021-05-21 14:47 [138][mmc]: Wrong media type 0x0 [141][mmc]: ***Try SD card 0*** [159][mmc]: HSSDR52/SDR25 4 bit [162][mmc]: 50000000 Hz [164][mmc]: 30436 MB [166][mmc]: ***SD/MMC 0 init OK!!!*** [259]Loading boot-pkg Succeed(index=0). [263]Entry_name = u-boot [269]Entry_name = optee [273]Entry_name = dtb [276]mmc not para [278]Jump to second Boot. M/TC: OP-TEE version: e9372c9c-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #2 Sat Mar 19 11:09:45 UTC 2022 arm U-Boot 2018.05 (Nov 01 2023 - 00:30:09 +0800) Allwinner Technology [00.331]CPU: Allwinner Family [00.334]Model: sun8iw20 [00.336]DRAM: 128 MiB [00.339]Relocation Offset is: 04ec8000 [00.364]secure enable bit: 0 E/TC:0 tee_read_fdt:433 fine node /firmware/optee failed with FDT_ERR_NOTFOUND [00.376]smc_tee_inform_fdt failed with: -65536[00.381]CPU=1200 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz [00.387]gic: sec monitor mode [00.390]flash init start [00.392]workmode = 0,storage type = 1 [00.395][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00 [00.400][mmc]: get sdc_type fail and use default host:tm1. [00.406][mmc]: can't find node "mmc0",will add new node [00.411][mmc]: fdt err returned <no error> [00.415][mmc]: Using default timing para [00.419][mmc]: SUNXI SDMMC Controller Version:0x50310 [00.445][mmc]: card_caps:0x3000000a [00.448][mmc]: host_caps:0x3000003f [00.453]sunxi flash init ok [00.455]line:703 init_clocks [00.458]drv_disp_init request pwm success, pwm7:pwm7:0x2000c00. fdt get node offset faill: hdmi [00.473]drv_disp_init finish [00.488]Loading Environment from SUNXI_FLASH... OK [00.506]boot_gui_init:start [00.509]set disp.dev2_output_type fail. using defval=0 [00.515]boot_gui_init:finish partno erro : can't find partition bootloader 54 bytes read in 1 ms (52.7 KiB/s) [00.530]bmp_name=bootlogo.bmp size 38454 38454 bytes read in 4 ms (9.2 MiB/s) [00.547]Item0 (Map) magic is bad [00.550]the secure storage item0 copy0 magic is bad [00.555]Item0 (Map) magic is bad [00.558]the secure storage item0 copy1 magic is bad [00.562]Item0 (Map) magic is bad [00.565]out of usb burn from boot: not need burn key List file under ULI/factory ** Unrecognized filesystem type ** root_partition is rootfs set root to /dev/mmcblk0p5 [00.584]update part info [00.587]update bootcmd [00.590]change working_fdt 0x43e77e70 to 0x43e47e70 disable nand error: FDT_ERR_BADPATH [00.611]update dts Hit any key to stop autoboot: 1 FDT ERROR:get muxsel err returned FDT_ERR_INTERNAL sunxi_pwm_pin_set_state, fdt_set_all_pin, ret=-1 [00.705]LCD open finish 0 [02.056]no vendor_boot partition is found Android's image name: sun8i_arm [02.068]Starting kernel ... [02.070][mmc]: MMC Device 2 not found [02.073][mmc]: mmc 2 not find, so not exit [ 0.000000] 000: printk: bootconsole [earlycon0] enabled [ 0.000000] 000: Memory policy: Data cache writealloc [ 0.000000] 000: cma: Reserved 4 MiB at 0x47c00000 [ 0.000000] 000: On node 0 totalpages: 32768 [ 0.000000] 000: Normal zone: 288 pages used for memmap [ 0.000000] 000: Normal zone: 0 pages reserved [ 0.000000] 000: Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] 000: psci: probing for conduit method from DT. [ 0.000000] 000: psci: PSCIv1.0 detected in firmware. [ 0.000000] 000: psci: Using standard PSCI v0.2 function IDs [ 0.000000] 000: psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] 000: psci: SMC Calling Convention v1.0 [ 0.000000] 000: percpu: Embedded 11 pages/cpu s15488 r8192 d21376 u45056 [ 0.000000] 000: pcpu-alloc: s15488 r8192 d21376 u45056 alloc=11*4096 [ 0.000000] 000: [ 0.000000] 000: pcpu-alloc: [ 0.000000] 000: [0] [ 0.000000] 000: 0 [ 0.000000] 000: [0] [ 0.000000] 000: 1 [ 0.000000] 000: [ 0.000000] 000: Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] 000: Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 rootdelay=2 loglevel=8 root=/dev/mmcblk0p5 init=/sbin/init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:dsp0@mmcblk0p6:private@mmcblk0p7:UDISK@mmcblk0p8 cma=4M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun8iw20p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.05(11/01/2023-00:30:09) mbr_offset=1032192 disp_reserve=1536000,0x43f12000 androidboot.dramsize=128 [ 0.000000] 000: Dentry cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.000000] 000: Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] 000: mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] 000: Memory: 104412K/131072K available (6144K kernel code, 478K rwdata, 2832K rodata, 1024K init, 358K bss, 22564K reserved, 4096K cma-reserved, 0K highmem) [ 0.000000] 000: SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] 000: rcu: Preemptible hierarchical RCU implementation. [ 0.000000] 000: rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] 000: rcu: RCU priority boosting: priority 1 delay 500 ms. [ 0.000000] 000: rcu: RCU_SOFTIRQ processing moved to rcuc kthreads. [ 0.000000] 000: No expedited grace period (rcu_normal_after_boot). [ 0.000000] 000: Tasks RCU enabled. [ 0.000000] 000: rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] 000: rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] 000: NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] 000: random: get_random_bytes called from start_kernel+0x1c7/0x318 with crng_init=0 [ 0.000000] 000: arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] 000: clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000000] 000: sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.008791] 000: Switching to timer-based delay loop, resolution 41ns [ 0.015361] 000: clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.025550] 000: Console: colour dummy device 80x30 [ 0.030667] 000: Calibrating delay loop (skipped), value calculated using timer frequency.. [ 0.039515] 000: 48.00 BogoMIPS (lpj=240000) [ 0.043786] 000: pid_max: default: 32768 minimum: 301 [ 0.049216] 000: Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.056991] 000: Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.066063] 000: CPU: Testing write buffer coherency: [ 0.071276] 000: ok [ 0.073677] 000: /cpus/cpu@0 missing clock-frequency property [ 0.079446] 000: /cpus/cpu@1 missing clock-frequency property [ 0.085482] 000: CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.092159] 000: Setting up static identity map for 0x40100000 - 0x40100054 [ 0.099261] 000: rcu: Hierarchical SRCU implementation. [ 0.105334] 000: BOOTEVENT: 105.333582: ON [ 0.110281] 000: smp: Bringing up secondary CPUs ... [ 0.116565] 001: CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.122955] 000: smp: Brought up 1 node, 2 CPUs [ 0.127654] 000: SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.134618] 000: CPU: All CPU(s) started in SVC mode. [ 0.140439] 001: devtmpfs: initialized [ 0.159074] 000: VFP support v0.3: [ 0.162587] 000: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.169610] 000: clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.180147] 000: futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.187743] 000: pinctrl core: initialized pinctrl subsystem [ 0.194809] 000: NET: Registered protocol family 16 [ 0.202792] 000: DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.246481] 000: rtc_ccu: sunxi ccu init OK [ 0.252910] 000: ccu: sunxi ccu init OK [ 0.257163] 000: r_ccu: sunxi ccu init OK [ 0.324876] 000: Deinterlace Module initialized. [ 0.329884] 000: iommu: Default domain type: Translated [ 0.335699] 000: sunxi iommu: irq = 24 [ 0.340784] 000: SCSI subsystem initialized [ 0.345915] 000: usbcore: registered new interface driver usbfs [ 0.351991] 000: usbcore: registered new interface driver hub [ 0.358156] 000: usbcore: registered new device driver usb [ 0.363946] 000: mc: Linux media interface: v0.10 [ 0.368848] 000: videodev: Linux video capture interface: v2.00 [ 0.376326] 000: Advanced Linux Sound Architecture Driver Initialized. [ 0.383819] 000: Bluetooth: Core ver 2.22 [ 0.388113] 000: NET: Registered protocol family 31 [ 0.393048] 000: Bluetooth: HCI device and connection manager initialized [ 0.399848] 000: Bluetooth: HCI socket layer initialized [ 0.405487] 000: Bluetooth: L2CAP socket layer initialized [ 0.411011] 000: Bluetooth: SCO socket layer initialized [ 0.416978] 000: pwm module init! [ 0.421929] 000: g2d 5410000.g2d: Adding to iommu group 0 [ 0.428148] 000: G2D: rcq version initialized.major:249 [ 0.434299] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor0_cameravdd supply, setting it to NULL! [ 0.443923] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor0_iovdd supply, setting it to NULL! [ 0.453481] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor0_avdd supply, setting it to NULL! [ 0.463006] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor0_dvdd supply, setting it to NULL! [ 0.472187] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor1_cameravdd supply, setting it to NULL! [ 0.481940] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor1_iovdd supply, setting it to NULL! [ 0.491080] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor1_avdd supply, setting it to NULL! [ 0.500181] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor1_dvdd supply, setting it to NULL! [ 0.510635] 000: clocksource: Switched to clocksource arch_sys_counter [ 0.527538] 000: sun8iw20-pinctrl pio: initialized sunXi PIO driver [ 0.548370] 000: thermal_sys: Registered thermal governor 'step_wise' [ 0.554894] 000: thermal_sys: Registered thermal governor 'user_space' [ 0.562024] 000: NET: Registered protocol family 2 [ 0.567700] 001: tcp_listen_portaddr_hash hash table entries: 128 (order: 0, 4096 bytes, linear) [ 0.576995] 001: TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.586526] 001: TCP bind hash table entries: 1024 (order: 2, 28672 bytes, linear) [ 0.594597] 001: TCP: Hash tables configured (established 1024 bind 1024) [ 0.602035] 001: UDP hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.609114] 001: UDP-Lite hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.617314] 001: NET: Registered protocol family 1 [ 0.622988] 001: RPC: Registered named UNIX socket transport module. [ 0.629632] 001: RPC: Registered udp transport module. [ 0.635126] 001: RPC: Registered tcp transport module. [ 0.640507] 001: RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.648784] 001: sun8iw20-pinctrl pio: pio supply vcc-pc not found, using dummy regulator [ 0.658144] 000: spi spi0: spi0 supply spi not found, using dummy regulator [ 0.665407] 000: sunxi_spi_resource_get()2198 - [spi0] SPI MASTER MODE [ 0.672267] 000: sunxi_spi_resource_get()2236 - Failed to get sample mode [ 0.679374] 000: sunxi_spi_resource_get()2241 - Failed to get sample delay [ 0.686628] 000: sunxi_spi_resource_get()2245 - sample_mode:-1431633921 sample_delay:-1431633921 [ 0.695906] 000: sunxi_spi_clk_init()2287 - [spi0] mclk 100000000 [ 0.702855] 000: sunxi_spi_probe()2700 - [spi0]: driver probe succeed, base c881f000, irq 39 [ 0.713593] 000: Initialise system trusted keyrings [ 0.718691] 000: workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.741898] 000: NFS: Registering the id_resolver key type [ 0.747412] 000: Key type id_resolver registered [ 0.752105] 000: Key type id_legacy registered [ 0.756573] 000: nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.763843] 000: nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.771889] 000: Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.779162] 000: fuse: init (API version 7.31) [ 0.811212] 001: NET: Registered protocol family 38 [ 0.816296] 001: Key type asymmetric registered [ 0.821228] 001: Asymmetric key parser 'x509' registered [ 0.826628] 001: Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.834699] 001: io scheduler mq-deadline registered [ 0.839891] 001: io scheduler kyber registered [ 0.844461] 001: atomic64_test: passed [ 0.850082] 001: [DISP]disp_module_init [ 0.854690] 001: disp 5000000.disp: Adding to iommu group 0 [ 0.860874] 001: [DISP] parser_disp_init_para,line:1430: [ 0.866430] 001: of_property_read fb0_width fail [ 0.871319] 001: [DISP] disp_init,line:2387: [ 0.875598] 001: smooth display screen:0 type:1 mode:4 [ 0.894390] 001: display_fb_request,fb_id:0 [ 0.901379] 001: disp_al_manager_apply ouput_type:1 [ 0.906483] 001: sunxi_pwm_enable_dual: can't parse pwm device [ 0.911274] 000: [DISP]disp_module_init finish [ 0.918152] 000: sunxi_sid_init()563 - insmod ok [ 0.923357] 000: pwm-regulator: supplied by regulator-dummy [ 0.930523] 000: sun8iw20-pinctrl pio: pio supply vcc-pe not found, using dummy regulator [ 0.939139] 000: uart uart0: get regulator failed [ 0.944095] 000: uart uart0: uart0 supply uart not found, using dummy regulator [ 0.952094] 000: uart0: ttyS0 at MMIO 0x2500000 (irq = 34, base_baud = 1500000) is a SUNXI [ 0.960851] 000: sw_console_setup()1784 - console setup baud 115200 parity n bits 8, flow n [ 0.969253] 000: printk: console [ttyS0] enabled [ 0.973945] 000: printk: bootconsole [earlycon0] disabled [ 0.000000] 000: Booting Linux on physical CPU 0x0 [ 0.000000] 000: Linux version 5.4.61-rt37 (ubuntu@win) (arm-linux-gnueabi-gcc (Linaro GCC 5.3-2016.05) 5.3.1 20160412, GNU ld (Linaro_Binutils-2016.05) 2.25.0 Linaro 2016_02) #2 SMP PREEMPT_RT Wed Nov 1 00:29:07 CST 2023 [ 0.000000] 000: CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c5387d [ 0.000000] 000: CPU: div instructions available: patching division code [ 0.000000] 000: CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] 000: OF: fdt: Machine model: sun8iw20 [ 0.000000] 000: printk: bootconsole [earlycon0] enabled [ 0.000000] 000: Memory policy: Data cache writealloc [ 0.000000] 000: cma: Reserved 4 MiB at 0x47c00000 [ 0.000000] 000: On node 0 totalpages: 32768 [ 0.000000] 000: Normal zone: 288 pages used for memmap [ 0.000000] 000: Normal zone: 0 pages reserved [ 0.000000] 000: Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] 000: psci: probing for conduit method from DT. [ 0.000000] 000: psci: PSCIv1.0 detected in firmware. [ 0.000000] 000: psci: Using standard PSCI v0.2 function IDs [ 0.000000] 000: psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] 000: psci: SMC Calling Convention v1.0 [ 0.000000] 000: percpu: Embedded 11 pages/cpu s15488 r8192 d21376 u45056 [ 0.000000] 000: pcpu-alloc: s15488 r8192 d21376 u45056 alloc=11*4096 [ 0.000000] 000: pcpu-alloc: [0] 0 [0] 1 [ 0.000000] 000: Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] 000: Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 rootdelay=2 loglevel=8 root=/dev/mmcblk0p5 init=/sbin/init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:dsp0@mmcblk0p6:private@mmcblk0p7:UDISK@mmcblk0p8 cma=4M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun8iw20p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.05(11/01/2023-00:30:09) mbr_offset=1032192 disp_reserve=1536000,0x43f12000 androidboot.dramsize=128 [ 0.000000] 000: Dentry cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.000000] 000: Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] 000: mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] 000: Memory: 104412K/131072K available (6144K kernel code, 478K rwdata, 2832K rodata, 1024K init, 358K bss, 22564K reserved, 4096K cma-reserved, 0K highmem) [ 0.000000] 000: SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] 000: rcu: Preemptible hierarchical RCU implementation. [ 0.000000] 000: rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] 000: rcu: RCU priority boosting: priority 1 delay 500 ms. [ 0.000000] 000: rcu: RCU_SOFTIRQ processing moved to rcuc kthreads. [ 0.000000] 000: No expedited grace period (rcu_normal_after_boot). [ 0.000000] 000: Tasks RCU enabled. [ 0.000000] 000: rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] 000: rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] 000: NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] 000: random: get_random_bytes called from start_kernel+0x1c7/0x318 with crng_init=0 [ 0.000000] 000: arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] 000: clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000000] 000: sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.008791] 000: Switching to timer-based delay loop, resolution 41ns [ 0.015361] 000: clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.025550] 000: Console: colour dummy device 80x30 [ 0.039503] 000: Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.043786] 000: pid_max: default: 32768 minimum: 301 [ 0.049216] 000: Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.056991] 000: Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.071221] 000: CPU: Testing write buffer coherency: ok [ 0.073677] 000: /cpus/cpu@0 missing clock-frequency property [ 0.079446] 000: /cpus/cpu@1 missing clock-frequency property [ 0.085482] 000: CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.092159] 000: Setting up static identity map for 0x40100000 - 0x40100054 [ 0.099261] 000: rcu: Hierarchical SRCU implementation. [ 0.105334] 000: BOOTEVENT: 105.333582: ON [ 0.110281] 000: smp: Bringing up secondary CPUs ... [ 0.116565] 001: CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.122955] 000: smp: Brought up 1 node, 2 CPUs [ 0.127654] 000: SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.134618] 000: CPU: All CPU(s) started in SVC mode. [ 0.140439] 001: devtmpfs: initialized [ 0.162579] 000: VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.169610] 000: clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.180147] 000: futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.187743] 000: pinctrl core: initialized pinctrl subsystem [ 0.194809] 000: NET: Registered protocol family 16 [ 0.202792] 000: DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.246481] 000: rtc_ccu: sunxi ccu init OK [ 0.252910] 000: ccu: sunxi ccu init OK [ 0.257163] 000: r_ccu: sunxi ccu init OK [ 0.324876] 000: Deinterlace Module initialized. [ 0.329884] 000: iommu: Default domain type: Translated [ 0.335699] 000: sunxi iommu: irq = 24 [ 0.340784] 000: SCSI subsystem initialized [ 0.345915] 000: usbcore: registered new interface driver usbfs [ 0.351991] 000: usbcore: registered new interface driver hub [ 0.358156] 000: usbcore: registered new device driver usb [ 0.363946] 000: mc: Linux media interface: v0.10 [ 0.368848] 000: videodev: Linux video capture interface: v2.00 [ 0.376326] 000: Advanced Linux Sound Architecture Driver Initialized. [ 0.383819] 000: Bluetooth: Core ver 2.22 [ 0.388113] 000: NET: Registered protocol family 31 [ 0.393048] 000: Bluetooth: HCI device and connection manager initialized [ 0.399848] 000: Bluetooth: HCI socket layer initialized [ 0.405487] 000: Bluetooth: L2CAP socket layer initialized [ 0.411011] 000: Bluetooth: SCO socket layer initialized [ 0.416978] 000: pwm module init! [ 0.421929] 000: g2d 5410000.g2d: Adding to iommu group 0 [ 0.428148] 000: G2D: rcq version initialized.major:249 [ 0.434299] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor0_cameravdd supply, setting it to NULL! [ 0.443923] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor0_iovdd supply, setting it to NULL! [ 0.453481] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor0_avdd supply, setting it to NULL! [ 0.463006] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor0_dvdd supply, setting it to NULL! [ 0.472187] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor1_cameravdd supply, setting it to NULL! [ 0.481940] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor1_iovdd supply, setting it to NULL! [ 0.491080] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor1_avdd supply, setting it to NULL! [ 0.500181] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor1_dvdd supply, setting it to NULL! [ 0.510635] 000: clocksource: Switched to clocksource arch_sys_counter [ 0.527538] 000: sun8iw20-pinctrl pio: initialized sunXi PIO driver [ 0.554813] 000: thermal_sys: Registered thermal governor 'step_wise' [ 0.561420] 000: thermal_sys: Registered thermal governor 'user_space' [ 0.562024] 000: NET: Registered protocol family 2 [ 0.567700] 001: tcp_listen_portaddr_hash hash table entries: 128 (order: 0, 4096 bytes, linear) [ 0.576995] 001: TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.586526] 001: TCP bind hash table entries: 1024 (order: 2, 28672 bytes, linear) [ 0.594597] 001: TCP: Hash tables configured (established 1024 bind 1024) [ 0.602035] 001: UDP hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.609114] 001: UDP-Lite hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.617314] 001: NET: Registered protocol family 1 [ 0.622988] 001: RPC: Registered named UNIX socket transport module. [ 0.629632] 001: RPC: Registered udp transport module. [ 0.635126] 001: RPC: Registered tcp transport module. [ 0.640507] 001: RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.648784] 001: sun8iw20-pinctrl pio: pio supply vcc-pc not found, using dummy regulator [ 0.658144] 000: spi spi0: spi0 supply spi not found, using dummy regulator [ 0.665407] 000: sunxi_spi_resource_get()2198 - [spi0] SPI MASTER MODE [ 0.672267] 000: sunxi_spi_resource_get()2236 - Failed to get sample mode [ 0.679374] 000: sunxi_spi_resource_get()2241 - Failed to get sample delay [ 0.686628] 000: sunxi_spi_resource_get()2245 - sample_mode:-1431633921 sample_delay:-1431633921 [ 0.695906] 000: sunxi_spi_clk_init()2287 - [spi0] mclk 100000000 [ 0.702855] 000: sunxi_spi_probe()2700 - [spi0]: driver probe succeed, base c881f000, irq 39 [ 0.713593] 000: Initialise system trusted keyrings [ 0.718691] 000: workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.741898] 000: NFS: Registering the id_resolver key type [ 0.747412] 000: Key type id_resolver registered [ 0.752105] 000: Key type id_legacy registered [ 0.756573] 000: nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.763843] 000: nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.771889] 000: Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.779162] 000: fuse: init (API version 7.31) [ 0.811212] 001: NET: Registered protocol family 38 [ 0.816296] 001: Key type asymmetric registered [ 0.821228] 001: Asymmetric key parser 'x509' registered [ 0.826628] 001: Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.834699] 001: io scheduler mq-deadline registered [ 0.839891] 001: io scheduler kyber registered [ 0.844461] 001: atomic64_test: passed [ 0.850082] 001: [DISP]disp_module_init [ 0.854690] 001: disp 5000000.disp: Adding to iommu group 0 [ 0.866429] 001: [DISP] parser_disp_init_para,line:1430: [ 0.866430] 001: of_property_read fb0_width fail [ 0.875597] 001: [DISP] disp_init,line:2387: [ 0.875598] 001: smooth display screen:0 type:1 mode:4 [ 0.894390] 001: display_fb_request,fb_id:0 [ 0.901379] 001: disp_al_manager_apply ouput_type:1 [ 0.906483] 001: sunxi_pwm_enable_dual: can't parse pwm device [ 0.911274] 000: [DISP]disp_module_init finish [ 0.918152] 000: sunxi_sid_init()563 - insmod ok [ 0.923357] 000: pwm-regulator: supplied by regulator-dummy [ 0.930523] 000: sun8iw20-pinctrl pio: pio supply vcc-pe not found, using dummy regulator [ 0.939139] 000: uart uart0: get regulator failed [ 0.944095] 000: uart uart0: uart0 supply uart not found, using dummy regulator [ 0.952094] 000: uart0: ttyS0 at MMIO 0x2500000 (irq = 34, base_baud = 1500000) is a SUNXI [ 0.960851] 000: sw_console_setup()1784 - console setup baud 115200 parity n bits 8, flow n [ 0.969253] 000: printk: console [ttyS0] enabled [ 0.973945] 000: printk: bootconsole [earlycon0] disabled [ 0.980588] 000: misc dump reg init [env.cfg
#kernel command arguments burn_key=0 earlyprintk=sunxi-uart,0x02500000 initcall_debug=0 console=ttyS0,115200 nand_root=/dev/ubiblock0_5 mmc_root=/dev/mmcblk0p5 mtd_name=sys rootfstype=ext4 root_partition=rootfs boot_partition=boot init=/sbin/init loglevel=8 cma=4M mac= wifi_mac= bt_mac= specialstr= #keybox_list=widevine,ec_key,ec_cert1,ec_cert2,ec_cert3,rsa_key,rsa_cert1,rsa_cert2,rsa_cert3 dsp0_partition=dsp0 rootdelay=2 #set kernel cmdline if boot.img or recovery.img has no cmdline we will use this setargs_nand=setenv bootargs ubi.mtd=${mtd_name} ubi.block=0,${root_partition} earlyprintk=${earlyprintk} clk_ignore_unused initcall_debug=${initcall_debug} console=${console} loglevel=${loglevel} root=${nand_root} rootfstype=${rootfstype} init=${init} partitions=${partitions} cma=${cma} snum=${snum} mac_addr=${mac} wifi_mac=${wifi_mac} bt_mac=${bt_mac} specialstr=${specialstr} gpt=1 setargs_nand_ubi=setenv bootargs ubi.mtd=${mtd_name} ubi.block=0,${root_partition} earlyprintk=${earlyprintk} clk_ignore_unused initcall_debug=${initcall_debug} console=${console} loglevel=${loglevel} root=${nand_root} rootfstype=${rootfstype} init=${init} partitions=${partitions} cma=${cma} snum=${snum} mac_addr=${mac} wifi_mac=${wifi_mac} bt_mac=${bt_mac} specialstr=${specialstr} gpt=1 setargs_mmc=setenv bootargs earlyprintk=${earlyprintk} clk_ignore_unused initcall_debug=${initcall_debug} console=${console} rootdelay=${rootdelay} loglevel=${loglevel} root=${mmc_root} init=${init} partitions=${partitions} cma=${cma} snum=${snum} mac_addr=${mac} wifi_mac=${wifi_mac} bt_mac=${bt_mac} specialstr=${specialstr} gpt=1 #nand command syntax: sunxi_flash read address partition_name read_bytes #0x4007f800 = 0x40080000(kernel entry) - 0x800(boot.img header 2k) #boot_dsp0=sunxi_flash read 43000000 ${dsp0_partition};bootr 43000000 0 0 #boot_normal=sunxi_flash read 43000000 ${boot_partition};bootm 43000000 boot_dsp0=sunxi_flash read 40000000 ${dsp0_partition};bootr 40000000 0 0 boot_normal=sunxi_flash read 42000000 ${boot_partition};bootm 42000000 boot_recovery=sunxi_flash read 43000000 recovery;bootm 43000000 boot_fastboot=fastboot #uboot system env config bootdelay=1 #default bootcmd, will change at runtime according to key press #default nand boot #bootcmd=run setargs_nand boot_dsp0 boot_normal bootcmd=run setargs_mmc boot_normal看起来内核启动了，但到了 misc dump reg init 就卡住了，重启无数次都这样，不知是否是 rootfs 加载失败。
请教各位大神提供一下思路，非常感谢。 -
@xsyr1024 在 请教如何排查 linux kernel 启动卡主的问题 中说：
[ 0.969253] 000: printk: console [ttyS0] enabled
[ 0.973945] 000: printk: bootconsole [earlycon0] disabled看着是earlycon0作为串口输出驱动正常，但是切换到ttyS0作为串口输出的时候ttyS0没有输出，先检查uart部分
另外这个是LinuxRT内核吗
-
@awwwwa 感谢大佬。是RT内核。我打开了 initcall_debug，看起来应该不是uart的问题。
[30]HELLO! BOOT0 is starting! [33]BOOT0 commit : adaf1174cc [36]set pll start [42]periph0 has been enabled [45]set pll end [46][pmu]: bus read error [49]board init ok [51]ZQ value = 0x2f [53]get_pmu_exist() = -1 [55]ddr_efuse_type: 0xa [58]trefi:7.8ms [60][AUTO DEBUG] single rank and full DQ! [64]ddr_efuse_type: 0xa [67]trefi:7.8ms [69][AUTO DEBUG] rank 0 row = 13 [72][AUTO DEBUG] rank 0 bank = 8 [75][AUTO DEBUG] rank 0 page size = 2 KB [79]DRAM BOOT DRIVE INFO: V0.33 [83]DRAM CLK = 936 MHz [85]DRAM Type = 3 (2:DDR2,3:DDR3) [88]DRAMC read ODT off. [91]DRAM ODT value: 0x42. [93]ddr_efuse_type: 0xa [96]DRAM SIZE =128 M [98]dram_tpr4:0x0 [100]PLL_DDR_CTRL_REG:0xf8004d00 [103]DRAM_CLK_REG:0xc0000000 [106][TIMING DEBUG] MR2= 0x20 [114]DRAM simple test OK. [116]rtc standby flag is 0x0, super standby flag is 0x0 [121]dram size =128 [124]card no is 0 [126]sdcard 0 line count 4 [128][mmc]: mmc driver ver 2021-05-21 14:47 [138][mmc]: Wrong media type 0x0 [141][mmc]: ***Try SD card 0*** [159][mmc]: HSSDR52/SDR25 4 bit [162][mmc]: 50000000 Hz [164][mmc]: 30436 MB [166][mmc]: ***SD/MMC 0 init OK!!!*** [259]Loading boot-pkg Succeed(index=0). [263]Entry_name = u-boot [270]Entry_name = optee [274]Entry_name = dtb [276]mmc not para [278]Jump to second Boot. M/TC: OP-TEE version: e9372c9c-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #2 Sat Mar 19 11:09:45 UTC 2022 arm U-Boot 2018.05 (Nov 02 2023 - 00:18:09 +0800) Allwinner Technology [00.331]CPU: Allwinner Family [00.334]Model: sun8iw20 [00.336]DRAM: 128 MiB [00.340]Relocation Offset is: 04ec8000 [00.365]secure enable bit: 0 E/TC:0 tee_read_fdt:433 fine node /firmware/optee failed with FDT_ERR_NOTFOUND [00.377]smc_tee_inform_fdt failed with: -65536[00.381]CPU=480 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz [00.388]gic: sec monitor mode [00.391]flash init start [00.393]workmode = 0,storage type = 1 [00.396][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00 [00.402][mmc]: get sdc_type fail and use default host:tm1. [00.409][mmc]: can't find node "mmc0",will add new node [00.414][mmc]: fdt err returned <no error> [00.417][mmc]: Using default timing para [00.421][mmc]: SUNXI SDMMC Controller Version:0x50310 [00.447][mmc]: card_caps:0x3000000a [00.450][mmc]: host_caps:0x3000003f [00.459]sunxi flash init ok [00.461]line:703 init_clocks [00.464]drv_disp_init request pwm success, pwm7:pwm7:0x2000c00. fdt get node offset faill: hdmi [00.489]drv_disp_init finish [00.504]Loading Environment from SUNXI_FLASH... OK [00.526]boot_gui_init:start [00.529]set disp.dev2_output_type fail. using defval=0 [00.537]boot_gui_init:finish partno erro : can't find partition bootloader 54 bytes read in 1 ms (52.7 KiB/s) [00.552]bmp_name=bootlogo.bmp size 38454 38454 bytes read in 4 ms (9.2 MiB/s) [00.597]Item0 (Map) magic is bad [00.600]the secure storage item0 copy0 magic is bad [00.632]Item0 (Map) magic is bad [00.635]the secure storage item0 copy1 magic is bad [00.639]Item0 (Map) magic is bad [00.642]out of usb burn from boot: not need burn key List file under ULI/factory ** Unrecognized filesystem type ** root_partition is rootfs set root to /dev/mmcblk0p5 [00.662]update part info [00.665]update bootcmd [00.668]change working_fdt 0x43e77e70 to 0x43e47e70 disable nand error: FDT_ERR_BADPATH [00.709]update dts FDT ERROR:get muxsel err returned FDT_ERR_INTERNAL sunxi_pwm_pin_set_state, fdt_set_all_pin, ret=-1 [00.728]LCD open finish Hit any key to stop autoboot: 0 [02.166]no vendor_boot partition is found Android's image name: sun8i_arm [02.180]Starting kernel ... [02.183][mmc]: MMC Device 2 not found [02.186][mmc]: mmc 2 not find, so not exit [ 0.000000] 000: printk: bootconsole [earlycon0] enabled [ 0.000000] 000: Memory policy: Data cache writealloc [ 0.000000] 000: cma: Reserved 4 MiB at 0x47c00000 [ 0.000000] 000: On node 0 totalpages: 32768 [ 0.000000] 000: Normal zone: 288 pages used for memmap [ 0.000000] 000: Normal zone: 0 pages reserved [ 0.000000] 000: Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] 000: psci: probing for conduit method from DT. [ 0.000000] 000: psci: PSCIv1.0 detected in firmware. [ 0.000000] 000: psci: Using standard PSCI v0.2 function IDs [ 0.000000] 000: psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] 000: psci: SMC Calling Convention v1.0 [ 0.000000] 000: percpu: Embedded 11 pages/cpu s15488 r8192 d21376 u45056 [ 0.000000] 000: pcpu-alloc: s15488 r8192 d21376 u45056 alloc=11*4096 [ 0.000000] 000: [ 0.000000] 000: pcpu-alloc: [ 0.000000] 000: [0] [ 0.000000] 000: 0 [ 0.000000] 000: [0] [ 0.000000] 000: 1 [ 0.000000] 000: [ 0.000000] 000: Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] 000: Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=1 console=ttyS0,115200 rootdelay=2 loglevel=8 root=/dev/mmcblk0p5 init=/sbin/init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:dsp0@mmcblk0p6:private@mmcblk0p7:UDISK@mmcblk0p8 cma=4M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun8iw20p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.05(11/02/2023-00:18:09) mbr_offset=1032192 disp_reserve=1536000,0x43f12000 androidboot.dramsize=128 [ 0.000000] 000: Dentry cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.000000] 000: Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] 000: mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] 000: Memory: 104412K/131072K available (6144K kernel code, 478K rwdata, 2832K rodata, 1024K init, 358K bss, 22564K reserved, 4096K cma-reserved, 0K highmem) [ 0.000000] 000: SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] 000: rcu: Preemptible hierarchical RCU implementation. [ 0.000000] 000: rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] 000: rcu: RCU priority boosting: priority 1 delay 500 ms. [ 0.000000] 000: rcu: RCU_SOFTIRQ processing moved to rcuc kthreads. [ 0.000000] 000: No expedited grace period (rcu_normal_after_boot). [ 0.000000] 000: Tasks RCU enabled. [ 0.000000] 000: rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] 000: rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] 000: NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] 000: random: get_random_bytes called from start_kernel+0x1c7/0x318 with crng_init=0 [ 0.000000] 000: arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] 000: clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] 000: sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.008461] 000: Switching to timer-based delay loop, resolution 41ns [ 0.015201] 000: clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.025995] 000: Console: colour dummy device 80x30 [ 0.030923] 000: Calibrating delay loop (skipped), value calculated using timer frequency.. [ 0.039375] 000: 48.00 BogoMIPS (lpj=240000) [ 0.043646] 000: pid_max: default: 32768 minimum: 301 [ 0.049063] 000: Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.056843] 000: Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.066984] 000: CPU: Testing write buffer coherency: [ 0.072196] 000: ok [ 0.074872] 000: /cpus/cpu@0 missing clock-frequency property [ 0.080706] 000: /cpus/cpu@1 missing clock-frequency property [ 0.086464] 000: CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.093852] 000: calling cpu_suspend_alloc_sp+0x1/0x68 @ 1 [ 0.099448] 000: initcall cpu_suspend_alloc_sp+0x1/0x68 returned 0 after 0 usecs [ 0.106940] 000: calling init_static_idmap+0x1/0xc4 @ 1 [ 0.112299] 000: Setting up static identity map for 0x40100000 - 0x40100054 [ 0.119293] 000: initcall init_static_idmap+0x1/0xc4 returned 0 after 9765 usecs [ 0.126711] 000: calling spawn_ksoftirqd+0x1/0x4c @ 1 [ 0.132112] 000: initcall spawn_ksoftirqd+0x1/0x4c returned 0 after 0 usecs [ 0.139092] 000: calling migration_init+0x1/0x30 @ 1 [ 0.144220] 000: initcall migration_init+0x1/0x30 returned 0 after 0 usecs [ 0.151119] 000: calling srcu_bootup_announce+0x1/0x2c @ 1 [ 0.156765] 000: rcu: Hierarchical SRCU implementation. [ 0.161987] 000: initcall srcu_bootup_announce+0x1/0x2c returned 0 after 0 usecs [ 0.169472] 000: calling rcu_sysrq_init+0x1/0x18 @ 1 [ 0.174530] 000: initcall rcu_sysrq_init+0x1/0x18 returned 0 after 0 usecs [ 0.181464] 000: calling check_cpu_stall_init+0x1/0x18 @ 1 [ 0.187055] 000: initcall check_cpu_stall_init+0x1/0x18 returned 0 after 0 usecs [ 0.194526] 000: calling rcu_spawn_gp_kthread+0x1/0x100 @ 1 [ 0.200612] 000: initcall rcu_spawn_gp_kthread+0x1/0x100 returned 0 after 0 usecs [ 0.208206] 000: calling rcu_spawn_core_kthreads+0x1/0x74 @ 1 [ 0.214268] 000: initcall rcu_spawn_core_kthreads+0x1/0x74 returned 0 after 0 usecs [ 0.222094] 000: calling posix_cpu_thread_init+0x1/0x58 @ 1 [ 0.228004] 000: initcall posix_cpu_thread_init+0x1/0x58 returned 0 after 0 usecs [ 0.235678] 000: calling cpu_stop_init+0x1/0x6c @ 1 [ 0.240893] 000: initcall cpu_stop_init+0x1/0x6c returned 0 after 0 usecs [ 0.247828] 000: calling mbus_init+0x1/0xcc @ 1 [ 0.252661] 000: initcall mbus_init+0x1/0xcc returned 0 after 0 usecs [ 0.259198] 000: calling init_boot_event+0x1/0x48 @ 1 [ 0.264361] 000: BOOTEVENT: 264.360998: ON [ 0.269003] 000: initcall init_boot_event+0x1/0x48 returned 0 after 0 usecs [ 0.276062] 000: calling dummy_timer_register+0x1/0x24 @ 1 [ 0.281652] 000: initcall dummy_timer_register+0x1/0x24 returned 0 after 0 usecs [ 0.289127] 000: calling initialize_ptr_random+0x1/0x38 @ 1 [ 0.294808] 000: initcall initialize_ptr_random+0x1/0x38 returned 0 after 0 usecs [ 0.302712] 000: smp: Bringing up secondary CPUs ... [ 0.310045] 001: CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.316450] 000: smp: Brought up 1 node, 2 CPUs [ 0.320986] 000: SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.327713] 000: CPU: All CPU(s) started in SVC mode. [ 0.333810] 001: devtmpfs: initialized [ 0.371093] 000: calling ipc_ns_init+0x1/0x10 @ 1 [ 0.375949] 000: initcall ipc_ns_init+0x1/0x10 returned 0 after 0 usecs [ 0.382685] 000: calling init_mmap_min_addr+0x1/0x14 @ 1 [ 0.388095] 000: initcall init_mmap_min_addr+0x1/0x14 returned 0 after 0 usecs [ 0.395401] 000: calling net_ns_init+0x1/0xd4 @ 1 [ 0.400660] 001: initcall net_ns_init+0x1/0xd4 returned 0 after 0 usecs [ 0.408719] 001: calling vfp_init+0x1/0x14c @ 1 [ 0.413441] 001: VFP support v0.3: [ 0.416938] 001: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.423526] 001: initcall vfp_init+0x1/0x14c returned 0 after 9765 usecs [ 0.430269] 001: calling ptrace_break_init+0x1/0x24 @ 1 [ 0.435665] 001: initcall ptrace_break_init+0x1/0x24 returned 0 after 0 usecs [ 0.442804] 001: calling register_cpufreq_notifier+0x1/0xc @ 1 [ 0.448786] 001: initcall register_cpufreq_notifier+0x1/0xc returned 0 after 0 usecs [ 0.456541] 001: calling v6_userpage_init+0x1/0x4 @ 1 [ 0.461733] 001: initcall v6_userpage_init+0x1/0x4 returned 0 after 0 usecs [ 0.468717] 001: calling cpu_hotplug_pm_sync_init+0x1/0x10 @ 1 [ 0.474702] 001: initcall cpu_hotplug_pm_sync_init+0x1/0x10 returned 0 after 0 usecs [ 0.482467] 001: calling alloc_frozen_cpus+0x1/0x4 @ 1 [ 0.487755] 001: initcall alloc_frozen_cpus+0x1/0x4 returned 0 after 0 usecs [ 0.494816] 001: calling wq_sysfs_init+0x1/0x24 @ 1 [ 0.500230] 001: initcall wq_sysfs_init+0x1/0x24 returned 0 after 0 usecs [ 0.507112] 001: calling ksysfs_init+0x1/0x68 @ 1 [ 0.512087] 001: initcall ksysfs_init+0x1/0x68 returned 0 after 0 usecs [ 0.518730] 001: calling sugov_register+0x1/0xc @ 1 [ 0.523767] 001: initcall sugov_register+0x1/0xc returned 0 after 0 usecs [ 0.530632] 001: calling pm_init+0x1/0x50 @ 1 [ 0.535540] 001: initcall pm_init+0x1/0x50 returned 0 after 0 usecs [ 0.541818] 001: calling rcu_spawn_tasks_kthread+0x1/0x64 @ 1 [ 0.547942] 000: initcall rcu_spawn_tasks_kthread+0x1/0x64 returned 0 after 0 usecs [ 0.555610] 000: calling rcu_set_runtime_mode+0x1/0x10 @ 1 [ 0.561297] 000: initcall rcu_set_runtime_mode+0x1/0x10 returned 0 after 0 usecs [ 0.568718] 000: calling dma_init_reserved_memory+0x1/0x3c @ 1 [ 0.574773] 000: initcall dma_init_reserved_memory+0x1/0x3c returned -12 after 0 usecs [ 0.582696] 000: calling init_jiffies_clocksource+0x1/0x10 @ 1 [ 0.588723] 000: clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.599089] 000: initcall init_jiffies_clocksource+0x1/0x10 returned 0 after 9765 usecs [ 0.607151] 000: calling futex_init+0x1/0xdc @ 1 [ 0.611968] 000: futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.619254] 000: initcall futex_init+0x1/0xdc returned 0 after 0 usecs [ 0.625942] 000: calling cgroup_wq_init+0x1/0x20 @ 1 [ 0.631076] 000: initcall cgroup_wq_init+0x1/0x20 returned 0 after 0 usecs [ 0.638046] 000: calling cgroup1_wq_init+0x1/0x20 @ 1 [ 0.643261] 000: initcall cgroup1_wq_init+0x1/0x20 returned 0 after 0 usecs [ 0.650325] 000: calling cpu_pm_init+0x1/0x10 @ 1 [ 0.655126] 000: initcall cpu_pm_init+0x1/0x10 returned 0 after 0 usecs [ 0.661798] 000: calling init_zero_pfn+0x1/0x34 @ 1 [ 0.666795] 000: initcall init_zero_pfn+0x1/0x34 returned 0 after 0 usecs [ 0.673657] 000: calling cma_init_reserved_areas+0x1/0x158 @ 1 [ 0.679922] 000: initcall cma_init_reserved_areas+0x1/0x158 returned 0 after 0 usecs [ 0.687738] 000: calling fsnotify_init+0x1/0x3c @ 1 [ 0.692774] 000: initcall fsnotify_init+0x1/0x3c returned 0 after 0 usecs [ 0.699644] 000: calling filelock_init+0x1/0x9c @ 1 [ 0.704683] 000: initcall filelock_init+0x1/0x9c returned 0 after 0 usecs [ 0.711559] 000: calling init_script_binfmt+0x1/0x14 @ 1 [ 0.716972] 000: initcall init_script_binfmt+0x1/0x14 returned 0 after 0 usecs [ 0.724263] 000: calling init_elf_binfmt+0x1/0x14 @ 1 [ 0.729423] 000: initcall init_elf_binfmt+0x1/0x14 returned 0 after 0 usecs [ 0.736453] 000: calling configfs_init+0x1/0x6c @ 1 [ 0.741513] 000: initcall configfs_init+0x1/0x6c returned 0 after 0 usecs [ 0.748375] 000: calling debugfs_init+0x1/0x3c @ 1 [ 0.753302] 000: initcall debugfs_init+0x1/0x3c returned 0 after 0 usecs [ 0.760076] 000: calling prandom_init+0x1/0xb4 @ 1 [ 0.764974] 000: initcall prandom_init+0x1/0xb4 returned 0 after 0 usecs [ 0.771750] 000: calling pinctrl_init+0x1/0x8c @ 1 [ 0.776633] 000: pinctrl core: initialized pinctrl subsystem [ 0.782595] 000: initcall pinctrl_init+0x1/0x8c returned 0 after 9765 usecs [ 0.789603] 000: calling gpiolib_dev_init+0x1/0x94 @ 1 [ 0.795054] 000: initcall gpiolib_dev_init+0x1/0x94 returned 0 after 0 usecs [ 0.802185] 000: calling sunxi_rtc_ccu_init+0x1/0x20 @ 1 [ 0.807798] 000: initcall sunxi_rtc_ccu_init+0x1/0x20 returned 0 after 0 usecs [ 0.815046] 000: calling sunxi_ccu_sun8iw20_init+0x1/0x20 @ 1 [ 0.821088] 000: initcall sunxi_ccu_sun8iw20_init+0x1/0x20 returned 0 after 0 usecs [ 0.828752] 000: calling sun8iw20_rtc_ccu_init+0x1/0x20 @ 1 [ 0.834618] 000: initcall sun8iw20_rtc_ccu_init+0x1/0x20 returned 0 after 0 usecs [ 0.842118] 000: calling sunxi_r_ccu_sun8iw20_init+0x1/0x20 @ 1 [ 0.848324] 000: initcall sunxi_r_ccu_sun8iw20_init+0x1/0x20 returned 0 after 0 usecs [ 0.856190] 000: calling virtio_init+0x1/0x1c @ 1 [ 0.861226] 000: initcall virtio_init+0x1/0x1c returned 0 after 0 usecs [ 0.867870] 000: calling regulator_init+0x1/0x78 @ 1 [ 0.874373] 000: probe of reg-dummy returned 1 after 0 usecs [ 0.880147] 000: initcall regulator_init+0x1/0x78 returned 0 after 0 usecs [ 0.887184] 000: calling iommu_init+0x1/0x28 @ 1 [ 0.891981] 000: initcall iommu_init+0x1/0x28 returned 0 after 0 usecs [ 0.898604] 000: calling component_debug_init+0x1/0x1c @ 1 [ 0.904235] 000: initcall component_debug_init+0x1/0x1c returned 0 after 0 usecs [ 0.911817] 000: calling register_cpufreq_notifier+0x1/0x28 @ 1 [ 0.917850] 000: initcall register_cpufreq_notifier+0x1/0x28 returned -22 after 0 usecs [ 0.925977] 000: calling opp_debug_init+0x1/0x1c @ 1 [ 0.931129] 000: initcall opp_debug_init+0x1/0x1c returned 0 after 0 usecs [ 0.938096] 000: calling cpufreq_core_init+0x1/0x34 @ 1 [ 0.943455] 000: initcall cpufreq_core_init+0x1/0x34 returned 0 after 0 usecs [ 0.950694] 000: calling cpufreq_gov_performance_init+0x1/0xc @ 1 [ 0.956884] 000: initcall cpufreq_gov_performance_init+0x1/0xc returned 0 after 0 usecs [ 0.964973] 000: calling sock_init+0x1/0x78 @ 1 [ 0.970059] 000: initcall sock_init+0x1/0x78 returned 0 after 0 usecs [ 0.976718] 000: calling net_inuse_init+0x1/0x1c @ 1 [ 0.981869] 000: initcall net_inuse_init+0x1/0x1c returned 0 after 0 usecs [ 0.988851] 000: calling net_defaults_init+0x1/0x1c @ 1 [ 0.994194] 000: initcall net_defaults_init+0x1/0x1c returned 0 after 0 usecs [ 1.001512] 000: calling init_default_flow_dissectors+0x1/0x48 @ 1 [ 1.007811] 000: initcall init_default_flow_dissectors+0x1/0x48 returned 0 after 0 usecs [ 1.015996] 000: calling netlink_proto_init+0x1/0xe4 @ 1 [ 1.021657] 000: NET: Registered protocol family 16 [ 1.026715] 000: initcall netlink_proto_init+0x1/0xe4 returned 0 after 9765 usecs [ 1.035674] 000: calling atomic_pool_init+0x1/0x124 @ 1 [ 1.046652] 000: DMA: preallocated 256 KiB pool for atomic coherent allocations [ 1.054046] 000: initcall atomic_pool_init+0x1/0x124 returned 0 after 9765 usecs [ 1.061473] 000: calling irq_sysfs_init+0x1/0x5c @ 1 [ 1.068235] 000: initcall irq_sysfs_init+0x1/0x5c returned 0 after 0 usecs [ 1.075130] 000: calling bdi_class_init+0x1/0x34 @ 1 [ 1.080457] 000: initcall bdi_class_init+0x1/0x34 returned 0 after 0 usecs [ 1.087345] 000: calling mm_sysfs_init+0x1/0x28 @ 1 [ 1.092423] 000: initcall mm_sysfs_init+0x1/0x28 returned 0 after 0 usecs [ 1.099270] 000: calling init_per_zone_wmark_min+0x1/0x50 @ 1 [ 1.105236] 000: initcall init_per_zone_wmark_min+0x1/0x50 returned 0 after 0 usecs [ 1.112918] 000: calling gpiolib_sysfs_init+0x1/0x68 @ 1 [ 1.118620] 000: initcall gpiolib_sysfs_init+0x1/0x68 returned 0 after 0 usecs [ 1.125863] 000: calling tty_class_init+0x1/0x2c @ 1 [ 1.131082] 000: initcall tty_class_init+0x1/0x2c returned 0 after 0 usecs [ 1.137983] 000: calling vtconsole_class_init+0x1/0xa8 @ 1 [ 1.144239] 000: initcall vtconsole_class_init+0x1/0xa8 returned 0 after 0 usecs [ 1.151667] 000: calling iommu_dev_init+0x1/0x10 @ 1 [ 1.156906] 000: initcall iommu_dev_init+0x1/0x10 returned 0 after 0 usecs [ 1.163855] 000: calling devlink_class_init+0x1/0x2c @ 1 [ 1.169436] 000: initcall devlink_class_init+0x1/0x2c returned 0 after 0 usecs [ 1.176675] 000: calling software_node_init+0x1/0x2c @ 1 [ 1.182302] 000: initcall software_node_init+0x1/0x2c returned 0 after 0 usecs [ 1.189552] 000: calling wakeup_sources_debugfs_init+0x1/0x24 @ 1 [ 1.195876] 000: initcall wakeup_sources_debugfs_init+0x1/0x24 returned 0 after 0 usecs [ 1.203947] 000: calling wakeup_sources_sysfs_init+0x1/0x24 @ 1 [ 1.210131] 000: initcall wakeup_sources_sysfs_init+0x1/0x24 returned 0 after 0 usecs [ 1.217970] 000: calling regmap_initcall+0x1/0xc @ 1 [ 1.223252] 000: initcall regmap_initcall+0x1/0xc returned 0 after 0 usecs [ 1.230154] 000: calling spi_init+0x1/0x58 @ 1 [ 1.235033] 000: initcall spi_init+0x1/0x58 returned 0 after 0 usecs [ 1.241461] 000: calling i2c_init+0x1/0x80 @ 1 [ 1.246385] 000: initcall i2c_init+0x1/0x80 returned 0 after 0 usecs [ 1.252771] 000: calling rpmsg_init+0x1/0x28 @ 1 [ 1.257818] 000: initcall rpmsg_init+0x1/0x28 returned 0 after 0 usecs [ 1.264359] 000: calling rpmsg_char_init+0x1/0x84 @ 1 [ 1.269782] 000: initcall rpmsg_char_init+0x1/0x84 returned 0 after 0 usecs [ 1.276771] 000: calling kobject_uevent_init+0x1/0xc @ 1 [ 1.282330] 000: initcall kobject_uevent_init+0x1/0xc returned 0 after 0 usecs [ 1.291033] 000: calling gate_vma_init+0x1/0x48 @ 1 [ 1.296123] 000: initcall gate_vma_init+0x1/0x48 returned 0 after 0 usecs [ 1.302940] 000: calling customize_machine+0x1/0x14 @ 1 [ 1.308346] 000: initcall customize_machine+0x1/0x14 returned 0 after 0 usecs [ 1.315503] 000: calling exceptions_init+0x1/0x58 @ 1 [ 1.320753] 000: initcall exceptions_init+0x1/0x58 returned 0 after 0 usecs [ 1.327731] 000: calling cryptomgr_init+0x1/0xc @ 1 [ 1.332803] 000: initcall cryptomgr_init+0x1/0xc returned 0 after 0 usecs [ 1.339617] 000: calling dma_bus_init+0x1/0x68 @ 1 [ 1.344729] 000: initcall dma_bus_init+0x1/0x68 returned 0 after 0 usecs [ 1.351440] 000: calling dma_channel_table_init+0x1/0xa0 @ 1 [ 1.357347] 000: initcall dma_channel_table_init+0x1/0xa0 returned 0 after 0 usecs [ 1.364931] 000: calling iommu_dma_init+0x1/0x4 @ 1 [ 1.370030] 000: initcall iommu_dma_init+0x1/0x4 returned 0 after 0 usecs [ 1.376835] 000: calling of_platform_default_populate_init+0x1/0x72 @ 1 [ 1.390413] 000: probe of 7090000.rtc_ccu returned -517 after 0 usecs [ 1.397478] 000: probe of 2001000.ccu returned -517 after 0 usecs [ 1.404013] 000: probe of 7010000.r_ccu returned -517 after 0 usecs [ 1.483803] 001: rtc_ccu: sunxi ccu init OK [ 1.488140] 001: probe of 7090000.rtc_ccu returned 1 after 0 usecs [ 1.499463] 001: ccu: sunxi ccu init OK [ 1.503624] 001: probe of 2001000.ccu returned 1 after 10000 usecs [ 1.510878] 001: r_ccu: sunxi ccu init OK [ 1.515041] 001: probe of 7010000.r_ccu returned 1 after 10000 usecs [ 1.523612] 001: initcall of_platform_default_populate_init+0x1/0x72 returned 0 after 126953 usecs [ 1.534356] 001: calling topology_init+0x1/0x48 @ 1 [ 1.540021] 001: initcall topology_init+0x1/0x48 returned 0 after 0 usecs [ 1.546941] 001: calling uid_cache_init+0x1/0x5c @ 1 [ 1.552066] 001: initcall uid_cache_init+0x1/0x5c returned 0 after 0 usecs [ 1.559101] 001: calling param_sysfs_init+0x1/0x14c @ 1 [ 1.618903] 001: initcall param_sysfs_init+0x1/0x14c returned 0 after 48828 usecs [ 1.626926] 001: calling user_namespace_sysctl_init+0x1/0x2c @ 1 [ 1.633122] 001: initcall user_namespace_sysctl_init+0x1/0x2c returned 0 after 0 usecs [ 1.641749] 000: calling pm_sysrq_init+0x1/0x14 @ 1 [ 1.646876] 001: initcall pm_sysrq_init+0x1/0x14 returned 0 after 0 usecs [ 1.654552] 001: calling create_proc_profile+0x1/0x94 @ 1 [ 1.660067] 001: initcall create_proc_profile+0x1/0x94 returned 0 after 0 usecs [ 1.667498] 001: calling cgroup_sysfs_init+0x1/0x14 @ 1 [ 1.672881] 001: initcall cgroup_sysfs_init+0x1/0x14 returned 0 after 0 usecs [ 1.680174] 001: calling cgroup_namespaces_init+0x1/0x4 @ 1 [ 1.685845] 001: initcall cgroup_namespaces_init+0x1/0x4 returned 0 after 0 usecs [ 1.693456] 001: calling dev_map_init+0x1/0x10 @ 1 [ 1.698348] 001: initcall dev_map_init+0x1/0x10 returned 0 after 0 usecs [ 1.705160] 001: calling oom_init+0x1/0x28 @ 1 [ 1.709954] 001: initcall oom_init+0x1/0x28 returned 0 after 0 usecs [ 1.716420] 001: calling cgwb_init+0x1/0x24 @ 1 [ 1.721122] 001: initcall cgwb_init+0x1/0x24 returned 0 after 0 usecs [ 1.727664] 001: calling default_bdi_init+0x1/0x78 @ 1 [ 1.733534] 001: initcall default_bdi_init+0x1/0x78 returned 0 after 0 usecs [ 1.740739] 001: calling percpu_enable_async+0x1/0x10 @ 1 [ 1.746252] 001: initcall percpu_enable_async+0x1/0x10 returned 0 after 0 usecs [ 1.753658] 001: calling init_reserve_notifier+0x1/0x4 @ 1 [ 1.759284] 001: initcall init_reserve_notifier+0x1/0x4 returned 0 after 0 usecs [ 1.766793] 001: calling init_admin_reserve+0x1/0x28 @ 1 [ 1.772203] 001: initcall init_admin_reserve+0x1/0x28 returned 0 after 0 usecs [ 1.779527] 001: calling init_user_reserve+0x1/0x28 @ 1 [ 1.784847] 001: initcall init_user_reserve+0x1/0x28 returned 0 after 0 usecs [ 1.792074] 001: calling swap_init_sysfs+0x1/0x4c @ 1 [ 1.797264] 001: initcall swap_init_sysfs+0x1/0x4c returned 0 after 0 usecs [ 1.804336] 001: calling swapfile_init+0x1/0x34 @ 1 [ 1.809317] 001: initcall swapfile_init+0x1/0x34 returned 0 after 0 usecs [ 1.816209] 001: calling mem_cgroup_init+0x1/0xc4 @ 1 [ 1.821455] 001: initcall mem_cgroup_init+0x1/0xc4 returned 0 after 0 usecs [ 1.828509] 001: calling rsa_init+0x1/0x28 @ 1 [ 1.833321] 000: initcall rsa_init+0x1/0x28 returned 0 after 0 usecs [ 1.839749] 000: calling crypto_cmac_module_init+0x1/0xc @ 1 [ 1.845617] 000: initcall crypto_cmac_module_init+0x1/0xc returned 0 after 0 usecs [ 1.853204] 000: calling hmac_module_init+0x1/0xc @ 1 [ 1.858531] 000: initcall hmac_module_init+0x1/0xc returned 0 after 0 usecs [ 1.865501] 000: calling crypto_null_mod_init+0x1/0x44 @ 1 [ 1.872060] 000: initcall crypto_null_mod_init+0x1/0x44 returned 0 after 0 usecs [ 1.879482] 000: calling sha256_generic_mod_init+0x1/0xc @ 1 [ 1.885805] 000: initcall sha256_generic_mod_init+0x1/0xc returned 0 after 0 usecs [ 1.893414] 000: calling crypto_ecb_module_init+0x1/0xc @ 1 [ 1.899215] 000: initcall crypto_ecb_module_init+0x1/0xc returned 0 after 0 usecs [ 1.906706] 000: calling des_generic_mod_init+0x1/0xc @ 1 [ 1.912727] 000: initcall des_generic_mod_init+0x1/0xc returned 0 after 0 usecs [ 1.920050] 000: calling aes_init+0x1/0xc @ 1 [ 1.924849] 000: initcall aes_init+0x1/0xc returned 0 after 0 usecs [ 1.931138] 000: calling arc4_init+0x1/0xc @ 1 [ 1.936004] 000: initcall arc4_init+0x1/0xc returned 0 after 0 usecs [ 1.942394] 000: calling deflate_mod_init+0x1/0x28 @ 1 [ 1.948396] 000: initcall deflate_mod_init+0x1/0x28 returned 0 after 0 usecs [ 1.955477] 000: calling crc32c_mod_init+0x1/0xc @ 1 [ 1.960896] 000: initcall crc32c_mod_init+0x1/0xc returned 0 after 0 usecs [ 1.967791] 000: calling lzo_mod_init+0x1/0x28 @ 1 [ 1.973234] 000: initcall lzo_mod_init+0x1/0x28 returned 0 after 0 usecs [ 1.979959] 000: calling lzorle_mod_init+0x1/0x28 @ 1 [ 1.985661] 000: initcall lzorle_mod_init+0x1/0x28 returned 0 after 0 usecs [ 1.992637] 000: calling drbg_init+0x1/0x58 @ 1 [ 1.999283] 000: initcall drbg_init+0x1/0x58 returned 0 after 0 usecs [ 2.005769] 000: calling zstd_mod_init+0x1/0x28 @ 1 [ 2.011331] 000: initcall zstd_mod_init+0x1/0x28 returned 0 after 0 usecs [ 2.018139] 000: calling ecdh_init+0x1/0xa @ 1 [ 2.023033] 000: initcall ecdh_init+0x1/0xa returned 0 after 0 usecs [ 2.029413] 000: calling init_bio+0x1/0x74 @ 1 [ 2.034210] 000: initcall init_bio+0x1/0x74 returned 0 after 0 usecs [ 2.040582] 000: calling blk_settings_init+0x1/0x24 @ 1 [ 2.046024] 000: initcall blk_settings_init+0x1/0x24 returned 0 after 0 usecs [ 2.053191] 000: calling blk_ioc_init+0x1/0x28 @ 1 [ 2.058205] 000: initcall blk_ioc_init+0x1/0x28 returned 0 after 0 usecs [ 2.064931] 000: calling blk_softirq_init+0x1/0x64 @ 1 [ 2.070287] 000: initcall blk_softirq_init+0x1/0x64 returned 0 after 0 usecs [ 2.077358] 000: calling blk_mq_init+0x1/0x28 @ 1 [ 2.082257] 000: initcall blk_mq_init+0x1/0x28 returned 0 after 0 usecs [ 2.088894] 000: calling genhd_device_init+0x1/0x5c @ 1 [ 2.094850] 000: initcall genhd_device_init+0x1/0x5c returned 0 after 0 usecs [ 2.102009] 000: calling blkcg_init+0x1/0x28 @ 1 [ 2.107405] 001: initcall blkcg_init+0x1/0x28 returned 0 after 0 usecs [ 2.114032] 001: calling gpiolib_debugfs_init+0x1/0x24 @ 1 [ 2.119738] 001: initcall gpiolib_debugfs_init+0x1/0x24 returned 0 after 0 usecs [ 2.127281] 001: calling pwm_debugfs_init+0x1/0x24 @ 1 [ 2.132556] 001: initcall pwm_debugfs_init+0x1/0x24 returned 0 after 0 usecs [ 2.139731] 001: calling pwm_sysfs_init+0x1/0x10 @ 1 [ 2.144859] 001: initcall pwm_sysfs_init+0x1/0x10 returned 0 after 0 usecs [ 2.151862] 001: calling fbmem_init+0x1/0x98 @ 1 [ 2.156679] 001: initcall fbmem_init+0x1/0x98 returned 0 after 0 usecs [ 2.163312] 001: calling sun6i_dma_init+0x1/0xc @ 1 [ 2.212820] 000: probe of 3002000.dma-controller returned 1 after 40000 usecs [ 2.221575] 000: initcall sun6i_dma_init+0x1/0xc returned 0 after 48828 usecs [ 2.228750] 000: calling regulator_fixed_voltage_init+0x1/0xc @ 1 [ 2.236156] 000: probe of pio-18 returned 1 after 0 usecs [ 2.242437] 000: probe of pio-33 returned 1 after 0 usecs [ 2.248622] 000: probe of usb1-vbus returned 0 after 0 usecs [ 2.254397] 000: initcall regulator_fixed_voltage_init+0x1/0xc returned 0 after 9765 usecs [ 2.262873] 000: calling misc_init+0x1/0x88 @ 1 [ 2.267619] 000: initcall misc_init+0x1/0x88 returned 0 after 0 usecs [ 2.274197] 000: calling sunxi_di_init+0x1/0x1c @ 1 [ 2.279198] 000: Deinterlace Module initialized. [ 2.284297] 000: probe of 5400000.deinterlace returned -517 after 0 usecs [ 2.291324] 000: initcall sunxi_di_init+0x1/0x1c returned 0 after 9765 usecs [ 2.298528] 000: calling iommu_subsys_init+0x1/0x4c @ 1 [ 2.303849] 000: iommu: Default domain type: Translated [ 2.309244] 000: initcall iommu_subsys_init+0x1/0x4c returned 0 after 9765 usecs [ 2.316659] 000: calling sunxi_iommu_init+0x1/0xc @ 1 [ 2.322256] 000: sunxi iommu: irq = 24 [ 2.327238] 000: probe of 2010000.iommu returned 1 after 0 usecs [ 2.333863] 000: initcall sunxi_iommu_init+0x1/0xc returned 0 after 9765 usecs [ 2.341126] 000: calling register_cpu_capacity_sysctl+0x1/0x50 @ 1 [ 2.347564] 000: initcall register_cpu_capacity_sysctl+0x1/0x50 returned 0 after 0 usecs [ 2.355699] 000: calling dma_buf_init+0x1/0x84 @ 1 [ 2.360914] 000: initcall dma_buf_init+0x1/0x84 returned 0 after 0 usecs [ 2.367627] 000: calling init_scsi+0x1/0x60 @ 1 [ 2.373069] 000: SCSI subsystem initialized [ 2.377257] 000: initcall init_scsi+0x1/0x60 returned 0 after 0 usecs [ 2.383841] 000: calling phy_init+0x1/0x148 @ 1 [ 2.388812] 000: initcall phy_init+0x1/0x148 returned 0 after 0 usecs [ 2.395387] 000: calling usb_common_init+0x1/0x1c @ 1 [ 2.400571] 000: initcall usb_common_init+0x1/0x1c returned 0 after 0 usecs [ 2.407629] 000: calling usb_init+0x1/0xd0 @ 1 [ 2.412584] 000: usbcore: registered new interface driver usbfs [ 2.418830] 000: usbcore: registered new interface driver hub [ 2.424795] 000: usbcore: registered new device driver usb [ 2.430393] 000: initcall usb_init+0x1/0xd0 returned 0 after 19531 usecs [ 2.437141] 000: calling usb_udc_init+0x1/0x3c @ 1 [ 2.442186] 000: initcall usb_udc_init+0x1/0x3c returned 0 after 0 usecs [ 2.448906] 000: calling usb_roles_init+0x1/0x24 @ 1 [ 2.454115] 000: initcall usb_roles_init+0x1/0x24 returned 0 after 0 usecs [ 2.461021] 000: calling serio_init+0x1/0x20 @ 1 [ 2.466018] 000: initcall serio_init+0x1/0x20 returned 0 after 0 usecs [ 2.472567] 000: calling input_init+0x1/0xac @ 1 [ 2.477490] 000: initcall input_init+0x1/0xac returned 0 after 0 usecs [ 2.484040] 000: calling rtc_init+0x1/0x3c @ 1 [ 2.488757] 000: initcall rtc_init+0x1/0x3c returned 0 after 0 usecs [ 2.495132] 000: calling media_devnode_init+0x1/0x64 @ 1 [ 2.500644] 000: mc: Linux media interface: v0.10 [ 2.505496] 000: initcall media_devnode_init+0x1/0x64 returned 0 after 0 usecs [ 2.512876] 000: calling videodev_init+0x1/0x68 @ 1 [ 2.517849] 000: videodev: Linux video capture interface: v2.00 [ 2.523920] 000: initcall videodev_init+0x1/0x68 returned 0 after 9765 usecs [ 2.531001] 000: calling rc_core_init+0x1/0x40 @ 1 [ 2.536070] 000: initcall rc_core_init+0x1/0x40 returned 0 after 0 usecs [ 2.542798] 000: calling power_supply_class_init+0x1/0x30 @ 1 [ 2.548876] 000: initcall power_supply_class_init+0x1/0x30 returned 0 after 0 usecs [ 2.556542] 000: calling hwmon_init+0x1/0x24 @ 1 [ 2.561416] 000: initcall hwmon_init+0x1/0x24 returned 0 after 0 usecs [ 2.567956] 000: calling mmc_init+0x1/0x24 @ 1 [ 2.572867] 000: initcall mmc_init+0x1/0x24 returned 0 after 0 usecs [ 2.579233] 000: calling leds_init+0x1/0x34 @ 1 [ 2.584058] 000: initcall leds_init+0x1/0x34 returned 0 after 0 usecs [ 2.590511] 000: calling ion_device_create+0x1/0xc8 @ 1 [ 2.596461] 000: initcall ion_device_create+0x1/0xc8 returned 0 after 0 usecs [ 2.603629] 000: calling ion_system_heap_init+0x1/0x58 @ 1 [ 2.609684] 000: initcall ion_system_heap_init+0x1/0x58 returned 0 after 0 usecs [ 2.617104] 000: calling ion_cma_heap_init+0x1/0x64 @ 1 [ 2.622645] 000: initcall ion_cma_heap_init+0x1/0x64 returned 0 after 0 usecs [ 2.629792] 000: calling remoteproc_init+0x1/0x10 @ 1 [ 2.635156] 000: initcall remoteproc_init+0x1/0x10 returned 0 after 0 usecs [ 2.642149] 000: calling rpmsg_init+0x1/0x28 @ 1 [ 2.647079] 000: initcall rpmsg_init+0x1/0x28 returned 0 after 0 usecs [ 2.653645] 000: calling iio_init+0x1/0x5c @ 1 [ 2.658455] 000: initcall iio_init+0x1/0x5c returned 0 after 0 usecs [ 2.664842] 000: calling nvmem_init+0x1/0xc @ 1 [ 2.669691] 000: initcall nvmem_init+0x1/0xc returned 0 after 0 usecs [ 2.676151] 000: calling init_soundcore+0x1/0x2c @ 1 [ 2.681390] 000: initcall init_soundcore+0x1/0x2c returned 0 after 0 usecs [ 2.688311] 000: calling alsa_sound_init+0x1/0x74 @ 1 [ 2.693638] 000: Advanced Linux Sound Architecture Driver Initialized. [ 2.700172] 000: initcall alsa_sound_init+0x1/0x74 returned 0 after 0 usecs [ 2.707265] 000: calling proto_init+0x1/0xc @ 1 [ 2.711931] 000: initcall proto_init+0x1/0xc returned 0 after 0 usecs [ 2.718474] 000: calling net_dev_init+0x1/0x1b4 @ 1 [ 2.724858] 000: initcall net_dev_init+0x1/0x1b4 returned 0 after 0 usecs [ 2.731818] 000: calling neigh_init+0x1/0x68 @ 1 [ 2.736556] 000: initcall neigh_init+0x1/0x68 returned 0 after 0 usecs [ 2.743177] 000: calling fib_notifier_init+0x1/0xc @ 1 [ 2.748432] 000: initcall fib_notifier_init+0x1/0xc returned 0 after 0 usecs [ 2.755593] 000: calling init_flow_indr_rhashtable+0x1/0x10 @ 1 [ 2.761631] 000: initcall init_flow_indr_rhashtable+0x1/0x10 returned 0 after 0 usecs [ 2.769554] 000: calling fib_rules_init+0x1/0x80 @ 1 [ 2.774627] 000: initcall fib_rules_init+0x1/0x80 returned 0 after 0 usecs [ 2.781613] 000: calling genl_init+0x1/0x2c @ 1 [ 2.786305] 000: initcall genl_init+0x1/0x2c returned 0 after 0 usecs [ 2.792840] 000: calling nexthop_init+0x1/0x94 @ 1 [ 2.797756] 000: initcall nexthop_init+0x1/0x94 returned 0 after 0 usecs [ 2.804556] 000: calling bt_init+0x1/0x80 @ 1 [ 2.809017] 000: Bluetooth: Core ver 2.22 [ 2.813188] 000: NET: Registered protocol family 31 [ 2.818156] 000: Bluetooth: HCI device and connection manager initialized [ 2.824971] 000: Bluetooth: HCI socket layer initialized [ 2.830403] 000: Bluetooth: L2CAP socket layer initialized [ 2.835945] 000: Bluetooth: SCO socket layer initialized [ 2.841396] 000: initcall bt_init+0x1/0x80 returned 0 after 29296 usecs [ 2.848044] 000: calling rfkill_init+0x1/0xb4 @ 1 [ 2.853446] 000: initcall rfkill_init+0x1/0xb4 returned 0 after 0 usecs [ 2.860108] 000: calling pwm_module_init+0x1/0x1c @ 1 [ 2.865369] 000: pwm module init! [ 2.870603] 000: probe of 2000c00.pwm returned 1 after 0 usecs [ 2.877053] 000: initcall pwm_module_init+0x1/0x1c returned 0 after 9765 usecs [ 2.884309] 000: calling g2d_module_init+0x1/0xcc @ 1 [ 2.890591] 000: g2d 5410000.g2d: Adding to iommu group 0 [ 2.896788] 000: probe of 5410000.g2d returned 1 after 0 usecs [ 2.903022] 000: G2D: rcq version initialized.major:249 [ 2.908251] 000: initcall g2d_module_init+0x1/0xcc returned 0 after 9765 usecs [ 2.915597] 000: calling sunxi_keyboard_init+0x1/0xc @ 1 [ 2.921719] 000: initcall sunxi_keyboard_init+0x1/0xc returned 0 after 0 usecs [ 2.929069] 000: calling sunxi_i2c_adap_init+0x1/0xc @ 1 [ 2.934796] 000: probe of 2502800.twi returned -517 after 0 usecs [ 2.941464] 000: initcall sunxi_i2c_adap_init+0x1/0xc returned 0 after 9765 usecs [ 2.948994] 000: calling vin_io_init+0x1/0x28 @ 1 [ 2.954344] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor0_cameravdd supply, setting it to NULL! [ 2.963971] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor0_iovdd supply, setting it to NULL! [ 2.973143] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor0_avdd supply, setting it to NULL! [ 2.982304] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor0_dvdd supply, setting it to NULL! [ 2.991507] 000: probe of 5809470.sensor returned 1 after 20000 usecs [ 2.998197] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor1_cameravdd supply, setting it to NULL! [ 3.007705] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor1_iovdd supply, setting it to NULL! [ 3.016967] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor1_avdd supply, setting it to NULL! [ 3.026023] 000: [VIN_WARN]sensor_helper_probe: cannot get sensor1_dvdd supply, setting it to NULL! [ 3.035268] 000: probe of 5809480.sensor returned 1 after 20000 usecs [ 3.041975] 000: initcall vin_io_init+0x1/0x28 returned 0 after 48828 usecs [ 3.049097] 000: calling watchdog_init+0x1/0x54 @ 1 [ 3.054367] 000: initcall watchdog_init+0x1/0x54 returned 0 after 0 usecs [ 3.062733] 000: calling proc_cpu_init+0x1/0x1c @ 1 [ 3.067750] 000: initcall proc_cpu_init+0x1/0x1c returned 0 after 0 usecs [ 3.074668] 000: calling alignment_init+0x1/0x90 @ 1 [ 3.079767] 000: initcall alignment_init+0x1/0x90 returned 0 after 0 usecs [ 3.086739] 000: calling clocksource_done_booting+0x1/0x2c @ 1 [ 3.092748] 000: clocksource: Switched to clocksource arch_sys_counter [ 3.099422] 000: initcall clocksource_done_booting+0x1/0x2c returned 0 after 6539 usecs [ 3.107539] 000: calling bpf_init+0x1/0x30 @ 1 [ 3.112121] 000: initcall bpf_init+0x1/0x30 returned 0 after 28 usecs [ 3.118688] 000: calling init_pipe_fs+0x1/0x30 @ 1 [ 3.123851] 000: initcall init_pipe_fs+0x1/0x30 returned 0 after 184 usecs [ 3.130745] 000: calling cgroup_writeback_init+0x1/0x24 @ 1 [ 3.136603] 000: initcall cgroup_writeback_init+0x1/0x24 returned 0 after 58 usecs [ 3.144298] 000: calling eventpoll_init+0x1/0xae @ 1 [ 3.149478] 000: initcall eventpoll_init+0x1/0xae returned 0 after 90 usecs [ 3.156575] 000: calling anon_inode_init+0x1/0x48 @ 1 [ 3.161884] 000: initcall anon_inode_init+0x1/0x48 returned 0 after 148 usecs [ 3.169146] 001: calling proc_locks_init+0x1/0x24 @ 1 [ 3.174402] 001: initcall proc_locks_init+0x1/0x24 returned 0 after 20 usecs [ 3.181458] 001: calling proc_cmdline_init+0x1/0x20 @ 1 [ 3.186871] 001: initcall proc_cmdline_init+0x1/0x20 returned 0 after 15 usecs [ 3.194194] 001: calling proc_consoles_init+0x1/0x24 @ 1 [ 3.199633] 001: initcall proc_consoles_init+0x1/0x24 returned 0 after 15 usecs [ 3.207007] 001: calling proc_cpuinfo_init+0x1/0x1c @ 1 [ 3.212348] 001: initcall proc_cpuinfo_init+0x1/0x1c returned 0 after 14 usecs [ 3.219663] 001: calling proc_devices_init+0x1/0x24 @ 1 [ 3.225066] 001: initcall proc_devices_init+0x1/0x24 returned 0 after 14 usecs [ 3.232312] 001: calling proc_interrupts_init+0x1/0x24 @ 1 [ 3.238004] 001: initcall proc_interrupts_init+0x1/0x24 returned 0 after 15 usecs [ 3.245571] 001: calling proc_loadavg_init+0x1/0x20 @ 1 [ 3.250914] 001: initcall proc_loadavg_init+0x1/0x20 returned 0 after 14 usecs [ 3.258200] 001: calling proc_meminfo_init+0x1/0x20 @ 1 [ 3.263611] 001: initcall proc_meminfo_init+0x1/0x20 returned 0 after 15 usecs [ 3.270857] 001: calling proc_stat_init+0x1/0x1c @ 1 [ 3.276006] 001: initcall proc_stat_init+0x1/0x1c returned 0 after 14 usecs [ 3.283034] 001: calling proc_uptime_init+0x1/0x20 @ 1 [ 3.288307] 001: initcall proc_uptime_init+0x1/0x20 returned 0 after 14 usecs [ 3.295523] 001: calling proc_version_init+0x1/0x20 @ 1 [ 3.300857] 001: initcall proc_version_init+0x1/0x20 returned 0 after 14 usecs [ 3.308151] 001: calling proc_softirqs_init+0x1/0x20 @ 1 [ 3.313641] 001: initcall proc_softirqs_init+0x1/0x20 returned 0 after 14 usecs [ 3.320965] 001: calling proc_kmsg_init+0x1/0x1c @ 1 [ 3.326116] 001: initcall proc_kmsg_init+0x1/0x1c returned 0 after 14 usecs [ 3.333182] 001: calling proc_page_init+0x1/0x48 @ 1 [ 3.338296] 001: initcall proc_page_init+0x1/0x48 returned 0 after 37 usecs [ 3.345333] 001: calling init_ramfs_fs+0x1/0xc @ 1 [ 3.350248] 001: initcall init_ramfs_fs+0x1/0xc returned 0 after 10 usecs [ 3.357118] 001: calling blk_scsi_ioctl_init+0x1/0x268 @ 1 [ 3.362719] 001: initcall blk_scsi_ioctl_init+0x1/0x268 returned 0 after 5 usecs [ 3.370176] 001: calling sun8iw20_pio_init+0x1/0xc @ 1 [ 3.398695] 001: sun8iw20-pinctrl pio: initialized sunXi PIO driver [ 3.405288] 001: probe of pio returned 1 after 29592 usecs [ 3.411279] 001: initcall sun8iw20_pio_init+0x1/0xc returned 0 after 34964 usecs [ 3.418830] 001: calling chr_dev_init+0x1/0xe8 @ 1 [ 3.453554] 000: initcall chr_dev_init+0x1/0xe8 returned 0 after 29050 usecs [ 3.460658] 000: calling firmware_class_init+0x1/0xc0 @ 1 [ 3.466291] 000: initcall firmware_class_init+0x1/0xc0 returned 0 after 9 usecs [ 3.474007] 000: calling udc_init+0x1/0x28 @ 1 [ 3.480724] 000: probe of 4100000.udc-controller returned 1 after 1752 usecs [ 3.488128] 000: initcall udc_init+0x1/0x28 returned 0 after 9340 usecs [ 3.495046] 000: calling thermal_init+0x1/0x110 @ 1 [ 3.500035] 000: thermal_sys: Registered thermal governor 'step_wise' [ 3.506575] 000: thermal_sys: Registered thermal governor 'user_space' [ 3.513991] 000: initcall thermal_init+0x1/0x110 returned 0 after 13631 usecs [ 3.521188] 000: calling sysctl_core_init+0x1/0x28 @ 1 [ 3.526681] 000: initcall sysctl_core_init+0x1/0x28 returned 0 after 105 usecs [ 3.534144] 000: calling eth_offload_init+0x1/0x10 @ 1 [ 3.539399] 000: initcall eth_offload_init+0x1/0x10 returned 0 after 3 usecs [ 3.546549] 000: calling inet_init+0x1/0x1c8 @ 1 [ 3.551459] 000: NET: Registered protocol family 2 [ 3.558081] 001: tcp_listen_portaddr_hash hash table entries: 128 (order: 0, 4096 bytes, linear) [ 3.567244] 001: TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 3.575524] 001: TCP bind hash table entries: 1024 (order: 2, 28672 bytes, linear) [ 3.583349] 001: TCP: Hash tables configured (established 1024 bind 1024) [ 3.590365] 001: UDP hash table entries: 256 (order: 2, 16384 bytes, linear) [ 3.597610] 000: UDP-Lite hash table entries: 256 (order: 2, 16384 bytes, linear) [ 3.605664] 000: initcall inet_init+0x1/0x1c8 returned 0 after 53110 usecs [ 3.612597] 000: calling ipv4_offload_init+0x1/0x58 @ 1 [ 3.618035] 000: initcall ipv4_offload_init+0x1/0x58 returned 0 after 5 usecs [ 3.625269] 000: calling af_unix_init+0x1/0x3c @ 1 [ 3.630240] 000: NET: Registered protocol family 1 [ 3.635181] 000: initcall af_unix_init+0x1/0x3c returned 0 after 4891 usecs [ 3.642182] 000: calling ipv6_offload_init+0x1/0x60 @ 1 [ 3.647649] 000: initcall ipv6_offload_init+0x1/0x60 returned 0 after 5 usecs [ 3.654874] 000: calling init_sunrpc+0x1/0x48 @ 1 [ 3.660865] 000: RPC: Registered named UNIX socket transport module. [ 3.667348] 000: RPC: Registered udp transport module. [ 3.672514] 000: RPC: Registered tcp transport module. [ 3.677728] 000: RPC: Registered tcp NFSv4.1 backchannel transport module. [ 3.684664] 000: initcall init_sunrpc+0x1/0x48 returned 0 after 24389 usecs [ 3.691650] 000: calling vlan_offload_init+0x1/0x1c @ 1 [ 3.697033] 000: initcall vlan_offload_init+0x1/0x1c returned 0 after 5 usecs [ 3.704262] 000: calling cfg80211_init+0x1/0x84 @ 1 [ 3.710336] 000: initcall cfg80211_init+0x1/0x84 returned 0 after 1068 usecs [ 3.717570] 000: calling dsp_debug_init+0x1/0xc @ 1 [ 3.723255] 000: initcall dsp_debug_init+0x1/0xc returned 0 after 683 usecs [ 3.730245] 000: calling sunxi_spi_init+0x1/0xc @ 1 [ 3.736208] 000: sun8iw20-pinctrl pio: pio supply vcc-pc not found, using dummy regulator [ 3.745828] 001: spi spi0: spi0 supply spi not found, using dummy regulator [ 3.753421] 001: sunxi_spi_resource_get()2198 - [spi0] SPI MASTER MODE [ 3.760047] 001: sunxi_spi_resource_get()2236 - Failed to get sample mode [ 3.766990] 001: sunxi_spi_resource_get()2241 - Failed to get sample delay [ 3.773964] 001: sunxi_spi_resource_get()2245 - sample_mode:-1431633921 sample_delay:-1431633921 [ 3.782992] 001: sunxi_spi_clk_init()2287 - [spi0] mclk 100000000 [ 3.790810] 001: sunxi_spi_probe()2700 - [spi0]: driver probe succeed, base c881f000, irq 39 [ 3.799545] 001: probe of spi0 returned 1 after 63934 usecs [ 3.805781] 001: initcall sunxi_spi_init+0x1/0xc returned 0 after 68794 usecs [ 3.813090] 001: calling default_rootfs+0x1/0x5c @ 1 [ 3.818307] 001: initcall default_rootfs+0x1/0x5c returned 0 after 142 usecs [ 3.826962] 001: calling proc_execdomains_init+0x1/0x20 @ 1 [ 3.832668] 001: initcall proc_execdomains_init+0x1/0x20 returned 0 after 25 usecs [ 3.840356] 001: calling register_warn_debugfs+0x1/0x24 @ 1 [ 3.846189] 001: initcall register_warn_debugfs+0x1/0x24 returned 0 after 41 usecs [ 3.853865] 001: calling cpuhp_sysfs_init+0x1/0x6c @ 1 [ 3.859267] 001: initcall cpuhp_sysfs_init+0x1/0x6c returned 0 after 148 usecs [ 3.866598] 001: calling ioresources_init+0x1/0x44 @ 1 [ 3.871872] 001: initcall ioresources_init+0x1/0x44 returned 0 after 31 usecs [ 3.879136] 001: calling irq_gc_init_ops+0x1/0x10 @ 1 [ 3.884393] 001: initcall irq_gc_init_ops+0x1/0x10 returned 0 after 2 usecs [ 3.891389] 001: calling irq_pm_init_ops+0x1/0x10 @ 1 [ 3.896661] 001: initcall irq_pm_init_ops+0x1/0x10 returned 0 after 1 usecs [ 3.903735] 001: calling timekeeping_init_ops+0x1/0x10 @ 1 [ 3.909334] 001: initcall timekeeping_init_ops+0x1/0x10 returned 0 after 1 usecs [ 3.916831] 001: calling init_clocksource_sysfs+0x1/0x20 @ 1 [ 3.923262] 001: initcall init_clocksource_sysfs+0x1/0x20 returned 0 after 644 usecs [ 3.931046] 001: calling init_timer_list_procfs+0x1/0x30 @ 1 [ 3.936927] 001: initcall init_timer_list_procfs+0x1/0x30 returned 0 after 20 usecs [ 3.944710] 001: calling alarmtimer_init+0x1/0xa0 @ 1 [ 3.950216] 001: initcall alarmtimer_init+0x1/0xa0 returned 0 after 332 usecs [ 3.957479] 001: calling init_posix_timers+0x1/0x28 @ 1 [ 3.962977] 001: initcall init_posix_timers+0x1/0x28 returned 0 after 74 usecs [ 3.970212] 001: calling clockevents_init_sysfs+0x1/0x94 @ 1 [ 3.977039] 001: initcall clockevents_init_sysfs+0x1/0x94 returned 0 after 941 usecs [ 3.984919] 001: calling sched_clock_syscore_init+0x1/0x10 @ 1 [ 3.990861] 001: initcall sched_clock_syscore_init+0x1/0x10 returned 0 after 1 usecs [ 3.998741] 001: calling proc_modules_init+0x1/0x1c @ 1 [ 4.004195] 001: initcall proc_modules_init+0x1/0x1c returned 0 after 24 usecs [ 4.011453] 001: calling modules_wq_init+0x1/0x24 @ 1 [ 4.016686] 001: initcall modules_wq_init+0x1/0x24 returned 0 after 0 usecs [ 4.023750] 001: calling kallsyms_init+0x1/0x1c @ 1 [ 4.028750] 001: initcall kallsyms_init+0x1/0x1c returned 0 after 17 usecs [ 4.035737] 001: calling pid_namespaces_init+0x1/0x28 @ 1 [ 4.041313] 001: initcall pid_namespaces_init+0x1/0x28 returned 0 after 66 usecs [ 4.048806] 001: calling ikconfig_init+0x1/0x38 @ 1 [ 4.053885] 001: initcall ikconfig_init+0x1/0x38 returned 0 after 18 usecs [ 4.060783] 001: calling utsname_sysctl_init+0x1/0x10 @ 1 [ 4.066397] 001: initcall utsname_sysctl_init+0x1/0x10 returned 0 after 39 usecs [ 4.073896] 001: calling system_trusted_keyring_init+0x1/0x5c @ 1 [ 4.080081] 001: Initialise system trusted keyrings [ 4.085111] 001: initcall system_trusted_keyring_init+0x1/0x5c returned 0 after 4912 usecs [ 4.093604] 001: calling kswapd_init+0x1/0x44 @ 1 [ 4.098648] 001: initcall kswapd_init+0x1/0x44 returned 0 after 223 usecs [ 4.105520] 001: calling mm_compute_batch_init+0x1/0x40 @ 1 [ 4.111212] 001: initcall mm_compute_batch_init+0x1/0x40 returned 0 after 0 usecs [ 4.118775] 001: calling slab_proc_init+0x1/0x1c @ 1 [ 4.123920] 001: initcall slab_proc_init+0x1/0x1c returned 0 after 20 usecs [ 4.130887] 001: calling workingset_init+0x1/0x64 @ 1 [ 4.136089] 001: workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 4.143031] 001: initcall workingset_init+0x1/0x64 returned 0 after 6780 usecs [ 4.150270] 001: calling proc_vmalloc_init+0x1/0x24 @ 1 [ 4.155671] 001: initcall proc_vmalloc_init+0x1/0x24 returned 0 after 16 usecs [ 4.162984] 001: calling memblock_init_debugfs+0x1/0x50 @ 1 [ 4.168762] 001: initcall memblock_init_debugfs+0x1/0x50 returned 0 after 92 usecs [ 4.176418] 001: calling procswaps_init+0x1/0x1c @ 1 [ 4.181493] 001: initcall procswaps_init+0x1/0x1c returned 0 after 15 usecs [ 4.188536] 001: calling slab_sysfs_init+0x1/0xb0 @ 1 [ 4.219083] 001: initcall slab_sysfs_init+0x1/0xb0 returned 0 after 24732 usecs [ 4.226586] 001: calling fcntl_init+0x1/0x28 @ 1 [ 4.231388] 001: initcall fcntl_init+0x1/0x28 returned 0 after 70 usecs [ 4.238191] 001: calling proc_filesystems_init+0x1/0x20 @ 1 [ 4.243996] 001: initcall proc_filesystems_init+0x1/0x20 returned 0 after 26 usecs [ 4.251583] 001: calling start_dirtytime_writeback+0x1/0x24 @ 1 [ 4.257757] 001: initcall start_dirtytime_writeback+0x1/0x24 returned 0 after 6 usecs [ 4.265704] 001: calling blkdev_init+0x1/0x10 @ 1 [ 4.270594] 001: initcall blkdev_init+0x1/0x10 returned 0 after 78 usecs [ 4.277471] 001: calling dio_init+0x1/0x28 @ 1 [ 4.282424] 001: initcall dio_init+0x1/0x28 returned 0 after 394 usecs [ 4.289080] 001: calling aio_setup+0x1/0x5c @ 1 [ 4.294387] 001: initcall aio_setup+0x1/0x5c returned 0 after 545 usecs [ 4.301042] 001: calling io_uring_init+0x1/0x28 @ 1 [ 4.306178] 001: initcall io_uring_init+0x1/0x28 returned 0 after 37 usecs [ 4.313239] 001: calling mbcache_init+0x1/0x30 @ 1 [ 4.318518] 001: initcall mbcache_init+0x1/0x30 returned 0 after 382 usecs [ 4.325515] 001: calling init_grace+0x1/0xc @ 1 [ 4.330160] 001: initcall init_grace+0x1/0xc returned 0 after 15 usecs [ 4.336810] 001: calling init_devpts_fs+0x1/0x20 @ 1 [ 4.341925] 001: initcall init_devpts_fs+0x1/0x20 returned 0 after 51 usecs [ 4.349009] 001: calling ext4_init_fs+0x1/0x124 @ 1 [ 4.356225] 001: initcall ext4_init_fs+0x1/0x124 returned 0 after 2094 usecs [ 4.363420] 001: calling init_ext2_fs+0x1/0x58 @ 1 [ 4.368655] 001: initcall init_ext2_fs+0x1/0x58 returned 0 after 336 usecs [ 4.375674] 001: calling journal_init+0x1/0xbc @ 1 [ 4.381827] 001: initcall journal_init+0x1/0xbc returned 0 after 1234 usecs [ 4.388923] 001: calling init_fat_fs+0x1/0x44 @ 1 [ 4.394504] 001: initcall init_fat_fs+0x1/0x44 returned 0 after 665 usecs [ 4.401316] 001: calling init_vfat_fs+0x1/0xc @ 1 [ 4.406246] 001: initcall init_vfat_fs+0x1/0xc returned 0 after 14 usecs [ 4.413049] 001: calling init_msdos_fs+0x1/0xc @ 1 [ 4.417945] 001: initcall init_msdos_fs+0x1/0xc returned 0 after 9 usecs [ 4.424767] 001: calling init_nfs_fs+0x1/0xe0 @ 1 [ 4.431127] 001: initcall init_nfs_fs+0x1/0xe0 returned 0 after 1514 usecs [ 4.438159] 001: calling init_nfs_v2+0x1/0x10 @ 1 [ 4.443113] 001: initcall init_nfs_v2+0x1/0x10 returned 0 after 3 usecs [ 4.449766] 001: calling init_nfs_v3+0x1/0x10 @ 1 [ 4.454655] 001: initcall init_nfs_v3+0x1/0x10 returned 0 after 2 usecs [ 4.461279] 001: calling init_nfs_v4+0x1/0x24 @ 1 [ 4.466203] 001: NFS: Registering the id_resolver key type [ 4.471735] 001: Key type id_resolver registered [ 4.476455] 001: Key type id_legacy registered [ 4.480937] 001: initcall init_nfs_v4+0x1/0x24 returned 0 after 14388 usecs [ 4.488025] 001: calling nfs4filelayout_init+0x1/0x20 @ 1 [ 4.493625] 001: nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 4.500761] 001: initcall nfs4filelayout_init+0x1/0x20 returned 0 after 6968 usecs [ 4.508457] 001: calling nfs4flexfilelayout_init+0x1/0x20 @ 1 [ 4.514385] 001: nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 4.522229] 001: initcall nfs4flexfilelayout_init+0x1/0x20 returned 0 after 7660 usecs [ 4.530362] 001: calling init_nfsd+0x1/0x98 @ 1 [ 4.535116] 001: Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 4.542200] 001: initcall init_nfsd+0x1/0x98 returned 0 after 6918 usecs [ 4.549145] 001: calling init_nlm+0x1/0x48 @ 1 [ 4.553847] 001: initcall init_nlm+0x1/0x48 returned 0 after 71 usecs [ 4.560306] 001: calling init_nls_cp437+0x1/0xc @ 1 [ 4.565366] 001: initcall init_nls_cp437+0x1/0xc returned 0 after 2 usecs [ 4.572170] 001: calling init_nls_iso8859_1+0x1/0xc @ 1 [ 4.577550] 001: initcall init_nls_iso8859_1+0x1/0xc returned 0 after 2 usecs [ 4.584771] 001: calling fuse_init+0x1/0xdc @ 1 [ 4.589406] 001: fuse: init (API version 7.31) [ 4.594806] 001: initcall fuse_init+0x1/0xdc returned 0 after 5273 usecs [ 4.601558] 001: calling ovl_init+0x1/0x4c @ 1 [ 4.606617] 001: initcall ovl_init+0x1/0x4c returned 0 after 367 usecs [ 4.613247] 001: calling ipc_init+0x1/0x20 @ 1 [ 4.617914] 001: initcall ipc_init+0x1/0x20 returned 0 after 105 usecs [ 4.624559] 001: calling ipc_sysctl_init+0x1/0x10 @ 1 [ 4.629765] 001: initcall ipc_sysctl_init+0x1/0x10 returned 0 after 49 usecs [ 4.636926] 001: calling init_mqueue_fs+0x1/0x8c @ 1 [ 4.642543] 001: initcall init_mqueue_fs+0x1/0x8c returned 0 after 533 usecs [ 4.649715] 001: calling key_proc_init+0x1/0x50 @ 1 [ 4.654822] 001: initcall key_proc_init+0x1/0x50 returned 0 after 35 usecs [ 4.661715] 001: calling crypto_algapi_init+0x1/0xc @ 1 [ 4.667132] 001: initcall crypto_algapi_init+0x1/0xc returned 0 after 15 usecs [ 4.674482] 001: calling jent_mod_init+0x1/0x28 @ 1 [ 4.745305] 000: initcall jent_mod_init+0x1/0x28 returned 0 after 64296 usecs [ 4.752498] 000: calling af_alg_init+0x1/0x2c @ 1 [ 4.757413] 000: NET: Registered protocol family 38 [ 4.762301] 000: initcall af_alg_init+0x1/0x2c returned 0 after 4778 usecs [ 4.769297] 000: calling algif_hash_init+0x1/0xc @ 1 [ 4.774474] 000: initcall algif_hash_init+0x1/0xc returned 0 after 4 usecs [ 4.781358] 000: calling algif_skcipher_init+0x1/0xc @ 1 [ 4.786843] 000: initcall algif_skcipher_init+0x1/0xc returned 0 after 4 usecs [ 4.794165] 000: calling rng_init+0x1/0xc @ 1 [ 4.798645] 000: initcall rng_init+0x1/0xc returned 0 after 4 usecs [ 4.804994] 000: calling algif_aead_init+0x1/0xc @ 1 [ 4.810063] 000: initcall algif_aead_init+0x1/0xc returned 0 after 4 usecs [ 4.817043] 000: calling asymmetric_key_init+0x1/0xc @ 1 [ 4.822451] 000: Key type asymmetric registered [ 4.827076] 000: initcall asymmetric_key_init+0x1/0xc returned 0 after 4520 usecs [ 4.834700] 000: calling x509_key_init+0x1/0xc @ 1 [ 4.839583] 000: Asymmetric key parser 'x509' registered [ 4.844998] 000: initcall x509_key_init+0x1/0xc returned 0 after 5290 usecs [ 4.851974] 000: calling proc_genhd_init+0x1/0x3c @ 1 [ 4.857223] 000: initcall proc_genhd_init+0x1/0x3c returned 0 after 33 usecs [ 4.864338] 000: calling init_emergency_pool+0x1/0x50 @ 1 [ 4.869847] 000: initcall init_emergency_pool+0x1/0x50 returned 0 after 1 usecs [ 4.877226] 000: calling bsg_init+0x1/0xb8 @ 1 [ 4.881851] 000: Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 4.889785] 000: initcall bsg_init+0x1/0xb8 returned 0 after 7835 usecs [ 4.896524] 000: calling deadline_init+0x1/0xc @ 1 [ 4.901410] 000: io scheduler mq-deadline registered [ 4.906470] 000: initcall deadline_init+0x1/0xc returned 0 after 4944 usecs [ 4.913551] 000: calling kyber_init+0x1/0xc @ 1 [ 4.918176] 000: io scheduler kyber registered [ 4.922616] 000: initcall kyber_init+0x1/0xc returned 0 after 4339 usecs [ 4.929454] 000: calling libcrc32c_mod_init+0x1/0x24 @ 1 [ 4.934963] 000: initcall libcrc32c_mod_init+0x1/0x24 returned 0 after 13 usecs [ 4.942277] 000: calling percpu_counter_startup+0x1/0x68 @ 1 [ 4.948233] 000: initcall percpu_counter_startup+0x1/0x68 returned 0 after 100 usecs [ 4.956094] 000: calling test_atomics_init+0x1/0x16a8 @ 1 [ 4.961637] 000: atomic64_test: passed [ 4.965480] 000: initcall test_atomics_init+0x1/0x16a8 returned 0 after 3795 usecs [ 4.973157] 000: calling sg_pool_init+0x1/0x98 @ 1 [ 4.979410] 000: initcall sg_pool_init+0x1/0x98 returned 0 after 1322 usecs [ 4.986498] 000: calling mbus_pmu_init+0x1/0x28 @ 1 [ 4.992484] 000: probe of 3102000.mbus-controller returned 1 after 787 usecs [ 5.000140] 000: initcall mbus_pmu_init+0x1/0x28 returned 0 after 8454 usecs [ 5.007335] 000: calling sunxi_pinctrl_debugfs_init+0x1/0xc4 @ 1 [ 5.013727] 000: initcall sunxi_pinctrl_debugfs_init+0x1/0xc4 returned 0 after 179 usecs [ 5.021834] 000: calling sunxi_pwm_init+0x1/0xfc @ 1 [ 5.027501] 000: initcall sunxi_pwm_init+0x1/0xfc returned 0 after 504 usecs [ 5.034674] 000: calling disp_module_init+0x1/0xd4 @ 1 [ 5.039908] 000: [DISP]disp_module_init [ 5.044944] 000: disp 5000000.disp: Adding to iommu group 0 [ 5.051714] 000: [DISP] parser_disp_init_para,line:1430: [ 5.057143] 000: of_property_read fb0_width fail [ 5.061790] 000: [DISP] disp_init,line:2387: [ 5.066176] 000: smooth display screen:0 type:1 mode:4 [ 5.105165] 000: display_fb_request,fb_id:0 [ 5.114809] 000: disp_al_manager_apply ouput_type:1 [ 5.120160] 000: sunxi_pwm_enable_dual: can't parse pwm device [ 5.123420] 001: probe of 5000000.disp returned 1 after 78636 usecs [ 5.132962] 001: [DISP]disp_module_init finish [ 5.137431] 001: initcall disp_module_init+0x1/0xd4 returned 0 after 95237 usecs [ 5.143125] 000: free logo buffer src_phy_addr=0x43f12000 fb_height=480 src_stride=3200 [ 5.144982] 001: calling of_fixed_factor_clk_driver_init+0x1/0xc @ 1 [ 5.156580] 000: Freeing logo buffer memory: 1500K [ 5.160105] 001: initcall of_fixed_factor_clk_driver_init+0x1/0xc returned 0 after 560 usecs [ 5.172952] 001: calling of_fixed_clk_driver_init+0x1/0xc @ 1 [ 5.179317] 001: initcall of_fixed_clk_driver_init+0x1/0xc returned 0 after 496 usecs [ 5.187301] 001: calling gpio_clk_driver_init+0x1/0xc @ 1 [ 5.193440] 001: initcall gpio_clk_driver_init+0x1/0xc returned 0 after 518 usecs [ 5.200942] 001: calling sunxi_sram_driver_init+0x1/0xc @ 1 [ 5.207897] 001: initcall sunxi_sram_driver_init+0x1/0xc returned 0 after 1160 usecs [ 5.215764] 001: calling sunxi_sid_init+0x1/0x1c @ 1 [ 5.220835] 001: sunxi_sid_init()563 - insmod ok [ 5.225557] 001: initcall sunxi_sid_init+0x1/0x1c returned 0 after 4611 usecs [ 5.232721] 001: calling pwm_regulator_driver_init+0x1/0xc @ 1 [ 5.239661] 001: pwm-regulator: supplied by regulator-dummy [ 5.246265] 001: probe of vdd-cpu returned 1 after 7133 usecs [ 5.252125] 001: initcall pwm_regulator_driver_init+0x1/0xc returned 0 after 13068 usecs [ 5.260378] 001: calling reset_simple_driver_init+0x1/0xc @ 1 [ 5.267362] 001: initcall reset_simple_driver_init+0x1/0xc returned 0 after 1021 usecs [ 5.275472] 001: calling n_null_init+0x1/0x14 @ 1 [ 5.280273] 001: initcall n_null_init+0x1/0x14 returned 0 after 2 usecs [ 5.286985] 001: calling pty_init+0x1/0x1a8 @ 1 [ 5.292125] 001: initcall pty_init+0x1/0x1a8 returned 0 after 493 usecs [ 5.298886] 001: calling sysrq_init+0x1/0x30 @ 1 [ 5.303739] 001: initcall sysrq_init+0x1/0x30 returned 0 after 38 usecs [ 5.310379] 001: calling sunxi_uart_init+0x1/0x38 @ 1 [ 5.316303] 001: sun8iw20-pinctrl pio: pio supply vcc-pe not found, using dummy regulator [ 5.325214] 001: uart uart0: get regulator failed [ 5.329982] 001: uart uart0: uart0 supply uart not found, using dummy regulator [ 5.338046] 001: uart0: ttyS0 at MMIO 0x2500000 (irq = 34, base_baud = 1500000) is a SUNXI [ 5.346450] 001: sw_console_setup()1784 - console setup baud 115200 parity n bits 8, flow n [ 5.354977] 001: printk: console [ttyS0] enabled [ 5.359615] 001: printk: bootconsole [earlycon0] disabled [ 0.655126] 000: initcall cpu_pm_init+0x1/0x10 returned 0 after 0 usecs ** 27 printk messages dropped ** [ 0.828752] 000: calling sun8iw20_rtc_ccu_init+0x1/0x20 @ 1 ** 1 printk message dropped ** [ 0.842118] 000: calling sunxi_r_ccu_sun8iw20_init+0x1/0x20 @ 1 [ 0.848324] 000: initcall sunxi_r_ccu_sun8iw20_init+0x1/0x20 returned 0 after 0 usecs [ 0.856190] 000: calling virtio_init+0x1/0x1c @ 1 [ 0.861226] 000: initcall virtio_init+0x1/0x1c returned 0 after 0 usecs [ 0.867870] 000: calling regulator_init+0x1/0x78 @ 1 [ 0.874373] 000: probe of reg-dummy returned 1 after 0 usecs [ 0.880147] 000: initcall regulator_init+0x1/0x78 returned 0 after 0 usecs [ 0.887184] 000: calling iommu_init+0x1/0x28 @ 1 [ 0.891981] 000: initcall iommu_init+0x1/0x28 returned 0 after 0 usecs ** 9 printk messages dropped ** [ 0.956884] 000: initcall cpufreq_gov_performance_init+0x1/0xc returned 0 after 0 usecs ** 4 printk messages dropped ** [ 0.988851] 000: calling net_defaults_init+0x1/0x1c @ 1 [ 0.994194] 000: initcall net_defaults_init+0x1/0x1c returned 0 after 0 usecs [ 1.001512] 000: calling init_default_flow_dissectors+0x1/0x48 @ 1 [ 1.007811] 000: initcall init_default_flow_dissectors+0x1/0x48 returned 0 after 0 usecs ** 38 printk messages dropped ** [ 1.264359] 000: calling rpmsg_char_init+0x1/0x84 @ 1 [ 1.269782] 000: initcall rpmsg_char_init+0x1/0x84 returned 0 after 0 usecs [ 1.276771] 000: calling kobject_uevent_init+0x1/0xc @ 1 [ 1.282330] 000: initcall kobject_uevent_init+0x1/0xc returned 0 after 0 usecs [ 1.291033] 000: calling gate_vma_init+0x1/0x48 @ 1 [ 1.296123] 000: initcall gate_vma_init+0x1/0x48 returned 0 after 0 usecs [ 1.302940] 000: calling customize_machine+0x1/0x14 @ 1 [ 1.308346] 000: initcall customize_machine+0x1/0x14 returned 0 after 0 usecs [ 1.315503] 000: calling exceptions_init+0x1/0x58 @ 1 [ 1.320753] 000: initcall exceptions_init+0x1/0x58 returned 0 after 0 usecs [ 1.327731] 000: calling cryptomgr_init+0x1/0xc @ 1 [ 1.332803] 000: initcall cryptomgr_init+0x1/0xc returned 0 after 0 usecs [ 1.339617] 000: calling dma_bus_init+0x1/0x68 @ 1 [ 1.344729] 000: initcall dma_bus_init+0x1/0x68 returned 0 after 0 usecs [ 1.351440] 000: calling dma_channel_table_init+0x1/0xa0 @ 1 [ 1.357347] 000: initcall dma_channel_table_init+0x1/0xa0 returned 0 after 0 usecs [ 1.364931] 000: calling iommu_dma_init+0x1/0x4 @ 1 [ 1.370030] 000: initcall iommu_dma_init+0x1/0x4 returned 0 after 0 usecs [ 1.376835] 000: calling of_platform_default_populate_init+0x1/0x72 @ 1 [ 1.390413] 000: probe of 7090000.rtc_ccu returned -517 after 0 usecs [ 1.397478] 000: probe of 2001000.ccu returned -517 after 0 usecs [ 1.404013] 000: probe of 7010000.r_ccu returned -517 after 0 usecs [ 1.483803] 001: rtc_ccu: sunxi ccu init OK [ 1.488140] 001: probe of 7090000.rtc_ccu returned 1 after 0 usecs [ 1.499463] 001: ccu: sunxi ccu init OK [ 1.503624] 001: probe of 2001000.ccu returned 1 after 10000 usecs [ 1.510878] 001: r_ccu: sunxi ccu init OK [ 1.515041] 001: probe of 7010000.r_ccu returned 1 after 10000 usecs [ 1.523612] 001: initcall of_platform_default_populate_init+0x1/0x72 returned 0 after 126953 usecs [ 1.534356] 001: calling topology_init+0x1/0x48 @ 1 [ 1.540021] 001: initcall topology_init+0x1/0x48 returned 0 after 0 usecs [ 1.546941] 001: calling uid_cache_init+0x1/0x5c @ 1 [ 1.552066] 001: initcall uid_cache_init+0x1/0x5c returned 0 after 0 usecs [ 1.559101] 001: calling param_sysfs_init+0x1/0x14c @ 1 [ 1.618903] 001: initcall param_sysfs_init+0x1/0x14c returned 0 after 48828 usecs [ 1.626926] 001: calling user_namespace_sysctl_init+0x1/0x2c @ 1 [ 1.633122] 001: initcall user_namespace_sysctl_init+0x1/0x2c returned 0 after 0 usecs [ 1.641749] 000: calling pm_sysrq_init+0x1/0x14 @ 1 [ 1.646876] 001: initcall pm_sysrq_init+0x1/0x14 returned 0 after 0 usecs [ 1.654552] 001: calling create_proc_profile+0x1/0x94 @ 1 [ 1.660067] 001: initcall create_proc_profile+0x1/0x94 returned 0 after 0 usecs [ 1.667498] 001: calling cgroup_sysfs_init+0x1/0x14 @ 1 [ 1.672881] 001: initcall cgroup_sysfs_init+0x1/0x14 returned 0 after 0 usecs [ 1.680174] 001: calling cgroup_namespaces_init+0x1/0x4 @ 1 [ 1.685845] 001: initcall cgroup_namespaces_init+0x1/0x4 returned 0 after 0 usecs [ 1.693456] 001: calling dev_map_init+0x1/0x10 @ 1 [ 1.698348] 001: initcall dev_map_init+0x1/0x10 returned 0 after 0 usecs [ 1.705160] 001: calling oom_init+0x1/0x28 @ 1 [ 1.709954] 001: initcall oom_init+0x1/0x28 returned 0 after 0 usecs [ 1.716420] 001: calling cgwb_init+0x1/0x24 @ 1 [ 1.721122] 001: initcall cgwb_init+0x1/0x24 returned 0 after 0 usecs [ 1.727664] 001: calling default_bdi_init+0x1/0x78 @ 1 [ 1.733534] 001: initcall default_bdi_init+0x1/0x78 returned 0 after 0 usecs [ 1.740739] 001: calling percpu_enable_async+0x1/0x10 @ 1 [ 1.746252] 001: initcall percpu_enable_async+0x1/0x10 returned 0 after 0 usecs [ 1.753658] 001: calling init_reserve_notifier+0x1/0x4 @ 1 [ 1.759284] 001: initcall init_reserve_notifier+0x1/0x4 returned 0 after 0 usecs [ 1.766793] 001: calling init_admin_reserve+0x1/0x28 @ 1 [ 1.772203] 001: initcall init_admin_reserve+0x1/0x28 returned 0 after 0 usecs [ 1.779527] 001: calling init_user_reserve+0x1/0x28 @ 1 [ 1.784847] 001: initcall init_user_reserve+0x1/0x28 returned 0 after 0 usecs [ 1.792074] 001: calling swap_init_sysfs+0x1/0x4c @ 1 [ 1.797264] 001: initcall swap_init_sysfs+0x1/0x4c returned 0 after 0 usecs [ 1.804336] 001: calling swapfile_init+0x1/0x34 @ 1 [ 1.809317] 001: initcall swapfile_init+0x1/0x34 returned 0 after 0 usecs [ 1.816209] 001: calling mem_cgroup_init+0x1/0xc4 @ 1 [ 1.821455] 001: initcall mem_cgroup_init+0x1/0xc4 returned 0 after 0 usecs [ 1.828509] 001: calling rsa_init+0x1/0x28 @ 1 [ 1.833321] 000: initcall rsa_init+0x1/0x28 returned 0 after 0 usecs [ 1.839749] 000: calling crypto_cmac_module_init+0x1/0xc @ 1 [ 1.845617] 000: initcall crypto_cmac_module_init+0x1/0xc returned 0 after 0 usecs [ 1.853204] 000: calling hmac_module_init+0x1/0xc @ 1 [ 1.858531] 000: initcall hmac_module_init+0x1/0xc returned 0 after 0 usecs [ 1.865501] 000: calling crypto_null_mod_init+0x1/0x44 @ 1 [ 1.872060] 000: initcall crypto_null_mod_init+0x1/0x44 returned 0 after 0 usecs [ 1.879482] 000: calling sha256_generic_mod_init+0x1/0xc @ 1 [ 1.885805] 000: initcall sha256_generic_mod_init+0x1/0xc returned 0 after 0 usecs [ 1.893414] 000: calling crypto_ecb_module_init+0x1/0xc @ 1 [ 1.899215] 000: initcall crypto_ecb_module_init+0x1/0xc returned 0 after 0 usecs [ 1.906706] 000: calling des_generic_mod_init+0x1/0xc @ 1 [ 1.912727] 000: initcall des_generic_mod_init+0x1/0xc returned 0 after 0 usecs [ 1.920050] 000: calling aes_init+0x1/0xc @ 1 [ 1.924849] 000: initcall aes_init+0x1/0xc returned 0 after 0 usecs [ 1.931138] 000: calling arc4_init+0x1/0xc @ 1 [ 1.936004] 000: initcall arc4_init+0x1/0xc returned 0 after 0 usecs [ 1.942394] 000: calling deflate_mod_init+0x1/0x28 @ 1 [ 1.948396] 000: initcall deflate_mod_init+0x1/0x28 returned 0 after 0 usecs [ 1.955477] 000: calling crc32c_mod_init+0x1/0xc @ 1 [ 1.960896] 000: initcall crc32c_mod_init+0x1/0xc returned 0 after 0 usecs [ 1.967791] 000: calling lzo_mod_init+0x1/0x28 @ 1 [ 1.973234] 000: initcall lzo_mod_init+0x1/0x28 returned 0 after 0 usecs [ 1.979959] 000: calling lzorle_mod_init+0x1/0x28 @ 1 [ 1.985661] 000: initcall lzorle_mod_init+0x1/0x28 returned 0 after 0 usecs [ 1.992637] 000: calling drbg_init+0x1/0x58 @ 1 [ 1.999283] 000: initcall drbg_init+0x1/0x58 returned 0 after 0 usecs [ 2.005769] 000: calling zstd_mod_init+0x1/0x28 @ 1 [ 2.011331] 000: initcall zstd_mod_init+0x1/0x28 returned 0 after 0 usecs [ 2.018139] 000: calling ecdh_init+0x1/0xa @ 1 [ 2.023033] 000: initcall ecdh_init+0x1/0xa returned 0 after 0 usecs [ 2.029413] 000: calling init_bio+0x1/0x74 @ 1 [ 2.034210] 000: initcall init_bio+0x1/0x74 returned 0 after 0 usecs [ 2.040582] 000: calling blk_settings_init+0x1/0x24 @ 1 [ 2.046024] 000: initcall blk_settings_init+0x1/0x24 returned 0 after 0 usecs [ 2.053191] 000: calling blk_ioc_init+0x1/0x28 @ 1 [ 2.058205] 000: initcall blk_ioc_init+0x1/0x28 returned 0 after 0 usecs [ 2.064931] 000: calling blk_softirq_init+0x1/0x64 @ 1 [ 2.070287] 000: initcall blk_softirq_init+0x1/0x64 returned 0 after 0 usecs [ 2.077358] 000: calling blk_mq_init+0x1/0x28 @ 1 [ 2.082257] 000: initcall blk_mq_init+0x1/0x28 returned 0 after 0 usecs [ 2.088894] 000: calling genhd_device_init+0x1/0x5c @ 1 [ 2.094850] 000: initcall genhd_device_init+0x1/0x5c returned 0 after 0 usecs [ 2.102009] 000: calling blkcg_init+0x1/0x28 @ 1 [ 2.107405] 001: initcall blkcg_init+0x1/0x28 returned 0 after 0 usecs [ 2.114032] 001: calling gpiolib_debugfs_init+0x1/0x24 @ 1 [ 2.119738] 001: initcall gpiolib_debugfs_init+0x1/0x24 returned 0 after 0 usecs [ 2.127281] 001: calling pwm_debugfs_init+0x1/0x24 @ 1 [ 2.132556] 001: initcall pwm_debugfs_init+0x1/0x24 returned 0 after 0 usecs [ 2.139731] 001: calling pwm_sysfs_init+0x1/0x10 @ 1 [ 2.144859] 001: initcall pwm_sysfs_init+0x1/0x10 returned 0 after 0 usecs [ 2.151862] 001: calling fbmem_init+0x1/0x98 @ 1 [ 2.156679] 001: initcall fbmem_init+0x1/0x98 returned 0 after 0 usecs [ 2.163312] 001: calling sun6i_dma_init+0x1/0xc @ 1 [ 2.212820] 000: probe of 3002000.dma-controller returned 1 after 40000 usecs [ 2.221575] 000: initcall sun6i_dma_init+0x1/0xc returned 0 after 48828 usecs [ 2.228750] 000: calling regulator_fixed_voltage_init+0x1/0xc @ 1 [ 2.236156] 000: probe of pio-18 returned 1 after 0 usecs [ 2.242437] 000: probe of pio-33 returned 1 after 0 usecs [ 2.248622] 000: probe of usb1-vbus returned 0 after 0 usecs [ 2.254397] 000: initcall regulator_fixed_voltage_init+0x1/0xc returned 0 after 9765 usecs [ 2.262873] 000: calling misc_init+0x1/0x88 @ 1 [ 2.267619] 000: initcall misc_init+0x1/0x88 returned 0 after 0 usecs [ 2.274197] 000: calling sunxi_di_init+0x1/0x1c @ 1 [ 2.279198] 000: Deinterlace Module initialized. [ 2.284297] 000: probe of 5400000.deinterlace returned -517 after 0 usecs [ 2.291324] 000: initcall sunxi_di_init+0x1/0x1c returned 0 after 9765 usecs [ 2.298528] 000: calling iommu_subsys_init+0x1/0x4c @ 1 [ 2.303849] 000: iommu: Default domain type: Translated [ 2.309244] 000: initcall iommu_subsys_init+0x1/0x4c returned 0 after 9765 usecs [ 2.316659] 000: calling sunxi_iommu_init+0x1/0xc @ 1 [ 2.322256] 000: sunxi iommu: irq = 24 [ 2.327238] 000: probe of 2010000.iommu returned 1 after 0 usecs [ 2.333863] 000: initcall sunxi_iommu_init+0x1/0xc returned 0 after 9765 usecs [ 2.341126] 000: calling register_cpu_capacity_sysctl+0x1/0x50 @ 1 [ 2.347564] 000: initcall register_cpu_capacity_sysctl+0x1/0x50 returned 0 after 0 usecs [ 2.355699] 000: calling dma_buf_init+0x1/0x84 @ 1 [ 2.360914] 000: initcall dma_buf_init+0x1/0x84 returned 0 after 0 usecs [ 2.367627] 000: calling init_scsi+0x1/0x60 @ 1 [ 2.373069] 000: SCSI subsystem initialized [ 2.377257] 000: initcall init_scsi+0x1/0x60 returned 0 after 0 usecs [ 2.383841] 000: calling phy_init+0x1/0x148 @ 1 [ 2.388812] 000: initcall phy_init+0x1/0x148 returned 0 after 0 usecs [ 2.395387] 000: calling usb_common_init+0x1/0x1c @ 1 [ 2.400571] 000: initcall usb_common_init+0x1/0x1c returned 0 after 0 usecs [ 2.407629] 000: calling usb_init+0x1/0xd0 @ 1 [ 2.412584] 000: usbcore: registered new interface driver usbfs [ 2.418830] 000: usbcore: registered new interface driver hub [ 2.424795] 000: usbcore: registered new device driver usb [ 2.430393] 000: initcall usb_init+0x1/0xd0 returned 0 after 19531 usecs [ 2.437141] 000: calling usb_udc_init+0x1/0x3c @ 1 [ 2.442186] 000: initcall usb_udc_init+0x1/0x3c returned 0 after 0 usecs [ 2.448906] 000: calling usb_roles_init+0x1/0x24 @ 1 [ 2.454115] 000: initcall usb_roles_init+0x1/0x24 returned 0 after 0 usecs [ 2.461021] 000: calling serio_init+0x1/0x20 @ 1 [ 2.466018] 000: initcall serio_init+0x1/0x20 returned 0 after 0 usecs [ 2.472567] 000: calling input_init+0x1/0xac @ 1 [ 2.477490] 000: in -
@xsyr1024
board.dts/* * Allwinner Technology CO., Ltd. */ /dts-v1/; /* optee used 7MB: SHM 2M: OS: 1M: TA:4M*/ /memreserve/ 0x41B00000 0x00100000; /* DSP used 1MB */ /*/memreserve/ 0x42000000 0x00100000;*/ #include "sun8iw20p1.dtsi" /{ model = "sun8iw20"; compatible = "allwinner,r528", "arm,sun8iw20p1"; reg_vdd_cpu: vdd-cpu { compatible = "sunxi-pwm-regulator"; pwms = <&pwm 3 5000 0>; regulator-name = "vdd_cpu"; regulator-min-microvolt = <810000>; regulator-max-microvolt = <1160000>; regulator-ramp-delay = <25>; regulator-always-on; regulator-boot-on; status = "okay"; }; reg_usb1_vbus: usb1-vbus { compatible = "regulator-fixed"; regulator-name = "usb1-vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; regulator-enable-ramp-delay = <1000>; gpio = <&pio PB 10 GPIO_ACTIVE_HIGH>; enable-active-high; }; }; &cpu0 { cpu-supply = <®_vdd_cpu>; }; &pio { sdc0_pins_a: sdc0@0 { allwinner,pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5"; allwinner,function = "sdc0"; allwinner,muxsel = <2>; allwinner,drive = <3>; allwinner,pull = <1>; pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5"; function = "sdc0"; drive-strength = <30>; bias-pull-up; power-source = <3300>; }; sdc0_pins_b: sdc0@1 { pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5"; function = "sdc0"; drive-strength = <30>; bias-pull-up; power-source = <1800>; }; sdc0_pins_c: sdc0@2 { pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5"; function = "gpio_in"; }; /* TODO: add jtag pin */ sdc0_pins_d: sdc0@3 { pins = "PF2", "PF4"; function = "uart0"; drive-strength = <10>; bias-pull-up; }; sdc0_pins_e: sdc0@4 { pins = "PF0", "PF1", "PF3", "PF5"; function = "jtag"; drive-strength = <10>; bias-pull-up; }; sdc1_pins_a: sdc1@0 { pins = "PG0", "PG1", "PG2", "PG3", "PG4", "PG5"; function = "sdc1"; drive-strength = <30>; bias-pull-up; }; sdc1_pins_b: sdc1@1 { pins = "PG0", "PG1", "PG2", "PG3", "PG4", "PG5"; function = "gpio_in"; }; sdc2_pins_a: sdc2@0 { allwinner,pins = "PC2", "PC3", "PC4", "PC5", "PC6", "PC7"; allwinner,function = "sdc2"; allwinner,muxsel = <3>; allwinner,drive = <3>; allwinner,pull = <1>; pins = "PC2", "PC3", "PC4", "PC5", "PC6", "PC7"; function = "sdc2"; drive-strength = <30>; bias-pull-up; }; sdc2_pins_b: sdc2@1 { pins = "PC2", "PC3", "PC4", "PC5", "PC6", "PC7"; function = "gpio_in"; }; wlan_pins_a:wlan@0 { pins = "PG11"; function = "clk_fanout1"; }; uart0_pins_a: uart0_pins@0 { /* For mangopi board */ pins = "PE2", "PE3"; function = "uart0"; drive-strength = <10>; bias-pull-up; }; uart0_pins_b: uart0_pins@1 { /* For mangopi board */ pins = "PE2", "PE3"; function = "gpio_in"; }; uart1_pins_a: uart1_pins@0 { /* For EVB1 board */ pins = "PG6", "PG7", "PG8", "PG9"; function = "uart1"; drive-strength = <10>; bias-pull-up; }; uart1_pins_b: uart1_pins { /* For EVB1 board */ pins = "PG6", "PG7", "PG8", "PG9"; function = "gpio_in"; }; uart2_pins_a: uart2_pins@0 { /* For EVB1 board */ pins = "PC0", "PC1"; function = "uart2"; drive-strength = <10>; bias-pull-up; }; uart2_pins_b: uart2_pins@1 { /* For EVB1 board */ pins = "PC0", "PC1"; function = "gpio_in"; }; uart3_pins_a: uart3_pins@0 { /* For EVB1 board */ pins = "PD10", "PD11"; function = "uart3"; muxsel = <5>; drive-strength = <10>; bias-pull-up; }; twi0_pins_a: twi0@0 { pins = "PB10", "PB11"; /*sck sda*/ function = "twi0"; drive-strength = <10>; }; twi0_pins_b: twi0@1 { pins = "PB10", "PB11"; function = "gpio_in"; }; twi1_pins_a: twi1@0 { pins = "PB4", "PB5"; function = "twi1"; drive-strength = <10>; }; twi1_pins_b: twi1@1 { pins = "PB4", "PB5"; function = "gpio_in"; }; twi2_pins_a: twi2@0 { pins = "PE12", "PE13"; function = "twi2"; drive-strength = <10>; }; twi2_pins_b: twi2@1 { pins = "PE12", "PE13"; function = "gpio_in"; }; twi3_pins_a: twi3@0 { pins = "PE6", "PE7"; function = "twi3"; drive-strength = <10>; }; twi3_pins_b: twi3@1 { pins = "PE6", "PE7"; function = "gpio_in"; }; gmac_pins_a: gmac@0 { pins = "PE0", "PE1", "PE2", "PE3", "PE4", "PE5", "PE6", "PE7", "PE8", "PE9", "PE10", "PE11", "PE12", "PE13", "PE14", "PE15"; function = "gmac0"; drive-strength = <10>; }; gmac_pins_b: gmac@1 { pins = "PE0", "PE1", "PE2", "PE3", "PE4", "PE5", "PE6", "PE7", "PE8", "PE9", "PE10", "PE11", "PE12", "PE13", "PE14", "PE15"; function = "gpio_in"; }; dmic_pins_a: dmic@0 { /* DMIC_PIN: CLK, DATA0, DATA1, DATA2, DATA3*/ pins = "PB12", "PB11", "PB10", "PE14", "PB8"; function = "dmic"; drive-strength = <20>; bias-disable; }; dmic_pins_b: dmic@1 { pins = "PB12", "PB11", "PB10", "PE14", "PB8"; function = "io_disabled"; drive-strength = <20>; bias-disable; }; daudio0_pins_a: daudio0@0 { pins = "PE17", "PE16", "PE15", "PE14", "PE13"; function = "i2s0"; drive-strength = <20>; bias-disable; }; daudio0_pins_b: daudio0_sleep@0 { pins = "PE17", "PE16", "PE15", "PE14", "PE13"; function = "io_disabled"; drive-strength = <20>; bias-disable; }; daudio1_pins_a: daudio1@0 { pins = "PG11", "PG12", "PG13", "PG14", "PG15"; function = "i2s1"; drive-strength = <20>; bias-disable; }; daudio1_pins_b: daudio1_sleep@0 { pins = "PG11", "PG12", "PG13", "PG14", "PG15"; function = "io_disabled"; drive-strength = <20>; bias-disable; }; daudio2_pins_a: daudio2@0 { /* I2S_PIN: MCLK, BCLK, LRCK */ pins = "PF6", "PF3", "PF5"; function = "i2s2"; drive-strength = <20>; bias-disable; }; daudio2_pins_b: daudio2@1 { /* I2S_PIN: DOUT0 */ pins = "PF1"; function = "i2s2_dout"; drive-strength = <20>; bias-disable; }; daudio2_pins_c: daudio2@2 { /* I2S_PIN: DIN0 */ pins = "PF0"; function = "i2s2_din"; drive-strength = <20>; bias-disable; }; daudio2_pins_d: daudio2_sleep@0 { pins = "PF6", "PF3", "PF5", "PF1", "PF0"; function = "io_disabled"; drive-strength = <20>; bias-disable; }; spdif_pins_a: spdif@0 { /* SPDIF_PIN: SPDIF_OUT */ pins = "PG18"; function = "spdif"; drive-strength = <20>; bias-disable; }; spdif_pins_b: spdif_sleep@0 { pins = "PG18"; function = "io_disabled"; drive-strength = <20>; bias-disable; }; spi0_pins_a: spi0@0 { pins = "PC2", "PC4", "PC5"; /* clk, mosi, miso */ function = "spi0"; muxsel = <2>; drive-strength = <10>; }; spi0_pins_b: spi0@1 { pins = "PC3", "PC7", "PC6"; function = "spi0"; muxsel = <2>; drive-strength = <10>; bias-pull-up; /* cs, hold, wp should be pulled up */ }; spi0_pins_c: spi0@2 { pins = "PC2", "PC3", "PC4", "PC5","PC6", "PC7"; function = "gpio_in"; muxsel = <0>; drive-strength = <10>; }; spi1_pins_a: spi1@0 { pins = "PD11", "PD12", "PD13"; /* clk, mosi, miso */ function = "spi1"; drive-strength = <10>; }; spi1_pins_b: spi1@1 { pins = "PD10", "PD14", "PD15"; function = "spi1"; drive-strength = <10>; bias-pull-up; /* cs, hold, wp should be pulled up */ }; spi1_pins_c: spi1@2 { pins = "PD10", "PD11", "PD12", "PD13","PD14", "PD15"; function = "gpio_in"; drive-strength = <10>; }; ledc_pins_a: ledc@0 { pins = "PC0"; function = "ledc"; drive-strength = <10>; }; ledc_pins_b: ledc@1 { pins = "PC0"; function = "gpio_in"; }; pwm0_pin_a: pwm0@0 { pins = "PD16"; function = "pwm0"; drive-strength = <10>; bias-pull-up; }; pwm0_pin_b: pwm0@1 { pins = "PD16"; function = "gpio_in"; bias-disable; }; pwm2_pin_a: pwm2@0 { pins = "PD18"; function = "pwm2"; drive-strength = <10>; bias-pull-up; }; pwm2_pin_b: pwm2@1 { pins = "PD18"; function = "gpio_out"; }; pwm7_pin_a: pwm7@0 { pins = "PD22"; function = "pwm7"; drive-strength = <10>; bias-pull-up; }; pwm7_pin_b: pwm7@1 { pins = "PD22"; function = "gpio_in"; }; s_cir0_pins_a: s_cir@0 { pins = "PB7"; function = "ir"; drive-strength = <10>; bias-pull-up; }; s_cir0_pins_b: s_cir@1 { pins = "PB7"; function = "gpio_in"; }; ir1_pins_a: ir1@0 { pins = "PB0"; function = "ir"; drive-strength = <10>; bias-pull-up; }; ir1_pins_b: ir1@1 { pins = "PB0"; function = "gpio_in"; }; }; &uart0 { pinctrl-names = "default", "sleep"; pinctrl-0 = <&uart0_pins_a>; pinctrl-1 = <&uart0_pins_b>; status = "okay"; }; &uart1 { pinctrl-names = "default", "sleep"; pinctrl-0 = <&uart1_pins_a>; pinctrl-1 = <&uart1_pins_b>; status = "disabled"; }; &uart2 { pinctrl-names = "default", "sleep"; pinctrl-0 = <&uart2_pins_a>; pinctrl-1 = <&uart2_pins_b>; status = "disabled"; }; &uart3 { compatible = "allwinner,sun20iw1-dsp-uart"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&uart3_pins_a>; pinctrl-1 = <&uart3_pins_a>; status = "disabled"; }; &soc { card0_boot_para@2 { /* * Avoid dtc compiling warnings. * @TODO: Developer should modify this to the actual value */ reg = <0x0 0x2 0x0 0x0>; device_type = "card0_boot_para"; card_ctrl = <0x0>; card_high_speed = <0x1>; card_line = <0x4>; pinctrl-0 = <&sdc0_pins_a>; }; card2_boot_para@3 { /* * Avoid dtc compiling warnings. * @TODO: Developer should modify this to the actual value */ reg = <0x0 0x3 0x0 0x0>; device_type = "card2_boot_para"; card_ctrl = <0x2>; card_high_speed = <0x1>; card_line = <0x4>; pinctrl-0 = <&sdc2_pins_a>; /*pinctrl-0 = <&sdc0_pins_a>;*/ /*sdc_ex_dly_used = <0x2>;*/ sdc_io_1v8 = <0x1>; /*sdc_type = "tm4";*/ sdc_tm4_hs200_max_freq = <150>; sdc_tm4_hs400_max_freq = <100>; sdc_ex_dly_used = <2>; /*sdc_tm4_win_th = <8>;*/ /*sdc_dis_host_caps = <0x180>;*/ }; rfkill: rfkill@0 { compatible = "allwinner,sunxi-rfkill"; chip_en; power_en; pinctrl-0 = <&wlan_pins_a>; pinctrl-names = "default"; status = "okay"; wlan: wlan@0 { compatible = "allwinner,sunxi-wlan"; clock-names = "32k-fanout1"; clocks = <&ccu CLK_FANOUT1_OUT>; wlan_busnum = <0x1>; wlan_regon = <&pio PG 12 GPIO_ACTIVE_HIGH>; wlan_hostwake = <&pio PG 10 GPIO_ACTIVE_HIGH>; /*wlan_power = "VCC-3V3";*/ /*wlan_power_vol = <3300000>;*/ /*interrupt-parent = <&pio>; interrupts = < PG 10 IRQ_TYPE_LEVEL_HIGH>;*/ wakeup-source; }; bt: bt@0 { compatible = "allwinner,sunxi-bt"; clock-names = "32k-fanout1"; clocks = <&ccu CLK_FANOUT1_OUT>; /*bt_power_num = <0x01>;*/ /*bt_power = "axp803-dldo1";*/ /*bt_io_regulator = "axp803-dldo1";*/ /*bt_io_vol = <3300000>;*/ /*bt_power_vol = <330000>;*/ bt_rst_n = <&pio PG 18 GPIO_ACTIVE_LOW>; status = "disabled"; }; }; btlpm: btlpm@0 { compatible = "allwinner,sunxi-btlpm"; uart_index = <0x1>; bt_wake = <&pio PG 14 GPIO_ACTIVE_HIGH>; bt_hostwake = <&pio PG 13 GPIO_ACTIVE_HIGH>; status = "disabled"; }; addr_mgt: addr_mgt@0 { compatible = "allwinner,sunxi-addr_mgt"; type_addr_wifi = <0x0>; type_addr_bt = <0x0>; type_addr_eth = <0x0>; status = "okay"; }; }; &sdc2 { non-removable; bus-width = <4>; mmc-ddr-1_8v; mmc-hs200-1_8v; no-sdio; no-sd; ctl-spec-caps = <0x308>; cap-mmc-highspeed; sunxi-power-save-mode; sunxi-dis-signal-vol-sw; mmc-bootpart-noacc; max-frequency = <150000000>; /*vmmc-supply = <®_dcdc1>;*/ /*emmc io vol 3.3v*/ /*vqmmc-supply = <®_aldo1>;*/ /*emmc io vol 1.8v*/ /*vqmmc-supply = <®_eldo1>;*/ status = "disabled"; }; &sdc0 { bus-width = <4>; cd-gpios = <&pio PF 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* mangopi */ /*non-removable;*/ /*broken-cd;*/ /*cd-inverted;*/ /*data3-detect;*/ /*card-pwr-gpios = <&pio PH 14 1 1 2 0xffffffff>;*/ /*cd-used-24M;*/ cap-sd-highspeed; /*sd-uhs-sdr50;*/ /*sd-uhs-ddr50;*/ /*sd-uhs-sdr104;*/ no-sdio; no-mmc; sunxi-power-save-mode; /*sunxi-dis-signal-vol-sw;*/ max-frequency = <150000000>; ctl-spec-caps = <0x8>; /*vmmc-supply = <®_dcdc1>;*/ /*vqmmc33sw-supply = <®_dcdc1>;*/ /*vdmmc33sw-supply = <®_dcdc1>;*/ /*vqmmc18sw-supply = <®_eldo1>;*/ /*vdmmc18sw-supply = <®_eldo1>;*/ status = "okay"; }; &sdc1 { bus-width = <4>; no-mmc; no-sd; cap-sd-highspeed; /*sd-uhs-sdr12*/ /*sd-uhs-sdr25;*/ /*sd-uhs-sdr50;*/ /*sd-uhs-ddr50;*/ /*sd-uhs-sdr104;*/ /*sunxi-power-save-mode;*/ /*sunxi-dis-signal-vol-sw;*/ cap-sdio-irq; keep-power-in-suspend; ignore-pm-notify; max-frequency = <150000000>; ctl-spec-caps = <0x8>; status = "okay"; }; /* tvd configuration used (create device, 0: do not create device, 1: create device) agc_auto_enable (0: agc manual mode,agc_manual_value is valid; 1: agc auto mode) agc_manual_value (agc manual value, default value is 64) cagc_enable (cagc 0: disable, 1: enable) fliter_used (3d fliter 0: disable, 1: enable) support two PMU power (tvd_power0, tvd_power1) support two GPIO power (tvd_gpio0, tvd_gpio1) NOTICE: If tvd need pmu power or gpio power,params need be configured under [tvd] tvd_sw (the switch of all tvd driver.) tvd_interface (0: cvbs, 1: ypbpr,) tvd_format (0:TVD_PL_YUV420 , 1: MB_YUV420, 2: TVD_PL_YUV422) tvd_system (0:ntsc, 1:pal) tvd_row (total row number in multi channel mode 1-2) tvd_column (total column number in multi channel mode 1-2) tvd_channelx_en (0:disable, 1~4:position in multi channel mode,In single channel mode,mean enable) tvd_row*tvd_column is the total tvd channel number to be used in multichannel mode +--------------------+--------------------+ | | | | | | | 1 | 2 | | | | | | | +--------------------+--------------------+ | | | | | | | 3 | 4 | | | | | | | +--------------------+--------------------+ */ &tvd { tvd_sw = <1>; tvd_interface = <0>; tvd_format = <0>; tvd_system = <1>; tvd_row = <1>; tvd_column = <1>; tvd_channel0_en = <1>; tvd_channel1_en = <0>; tvd_channel2_en = <0>; tvd_channel3_en = <0>; /*tvd_gpio0 = <&pio PD 22 GPIO_ACTIVE_HIGH>;*/ /*tvd_gpio1 = <&pio PD 23 GPIO_ACTIVE_HIGH>;*/ /*tvd_gpio2 = <&pio PD 24 GPIO_ACTIVE_HIGH>;*/ /* dc1sw-supply = <®_dc1sw>;*/ /* eldo3-supply = <®_eldo3>;*/ /*tvd_power0 = "dc1sw"*/ /*tvd_power1 = "eldo3"*/ }; &tvd0 { used = <1>; agc_auto_enable = <1>; agc_manual_value = <64>; cagc_enable = <1>; fliter_used = <1>; }; /* Audio Driver modules */ &sunxi_rpaf_dsp0 { status = "disabled"; }; /* if audiocodec is used, sdc0 and uart0 should be closed to enable PA. */ &codec { /* MIC and headphone gain setting */ mic1gain = <0x1F>; mic2gain = <0x1F>; mic3gain = <0x1F>; /* ADC/DAC DRC/HPF func enabled */ /* 0x1:DAP_HP_EN; 0x2:DAP_SPK_EN; 0x3:DAP_HPSPK_EN */ adcdrc_cfg = <0x0>; adchpf_cfg = <0x1>; dacdrc_cfg = <0x0>; dachpf_cfg = <0x0>; /* Volume about */ digital_vol = <0x00>; lineout_vol = <0x1a>; headphonegain = <0x03>; /* Pa enabled about */ pa_level = <0x01>; pa_pwr_level = <0x01>; pa_msleep_time = <0x78>; /* gpio-spk = <&pio PF 2 GPIO_ACTIVE_HIGH>;*/ /* gpio-spk-pwr = <&pio PF 4 GPIO_ACTIVE_HIGH>; */ /* CMA config about */ playback_cma = <128>; capture_cma = <256>; /* regulator about */ /* avcc-supply = <®_aldo1>; */ /* hpvcc-supply = <®_eldo1>; */ status = "okay"; }; &sndcodec { hp_detect_case = <0x00>; jack_enable = <0x01>; status = "okay"; }; &dummy_cpudai { status = "okay"; }; &dmic { pinctrl-names = "default","sleep"; pinctrl-0 = <&dmic_pins_a>; pinctrl-1 = <&dmic_pins_b>; status = "disabled"; }; &dmic_codec { status = "okay"; }; &sounddmic { status = "okay"; }; /*----------------------------------------------------------------------------- * pcm_lrck_period 16/32/64/128/256 * slot_width_select 16bits/20bits/24bits/32bits * frametype 0 --> short frame = 1 clock width; * 1 --> long frame = 2 clock width; * tdm_config 0 --> pcm * 1 --> i2s * mclk_div 0 --> not output * 1/2/4/6/8/12/16/24/32/48/64/96/128/176/192 * (set mclk as external codec clk source, freq is pll_audio/mclk_div) * pinctrl_used 0 --> I2S/PCM use for internal * 1 --> I2S/PCM use for external audio * daudio_type: 0 --> external audio type *---------------------------------------------------------------------------*/ &daudio0 { mclk_div = <0x01>; frametype = <0x00>; tdm_config = <0x01>; sign_extend = <0x00>; msb_lsb_first = <0x00>; pcm_lrck_period = <0x80>; slot_width_select = <0x20>; pinctrl-names = "default", "sleep"; pinctrl-0 = <&daudio0_pins_a>; pinctrl-1 = <&daudio0_pins_b>; pinctrl_used = <0x0>; status = "disabled"; }; /*----------------------------------------------------------------------------- * simple-audio-card,name name of sound card, e.g. * "snddaudio0" --> use for external audio * sound-dai "snd-soc-dummy" --> use for I2S * "ac108" --> use for external audio of ac108 *---------------------------------------------------------------------------*/ &sounddaudio0 { /* simple-audio-card,format = "i2s"; */ /* simple-audio-card,frame-master = <&daudio0_master>; */ /* simple-audio-card,bitclock-master = <&daudio0_master>; */ /* simple-audio-card,bitclock-inversion; */ /* simple-audio-card,frame-inversion; */ status = "disabled"; daudio0_master: simple-audio-card,codec { /* sound-dai = <&ac108>; */ }; }; &daudio1 { mclk_div = <0x01>; frametype = <0x00>; tdm_config = <0x01>; sign_extend = <0x00>; msb_lsb_first = <0x00>; pcm_lrck_period = <0x80>; slot_width_select = <0x20>; pinctrl-names = "default", "sleep"; pinctrl-0 = <&daudio1_pins_a>; pinctrl-1 = <&daudio1_pins_b>; pinctrl_used = <0x0>; status = "disabled"; }; &sounddaudio1 { status = "disabled"; daudio1_master: simple-audio-card,codec { /* sound-dai = <&ac108>; */ }; }; &daudio2 { mclk_div = <0x01>; frametype = <0x00>; tdm_config = <0x01>; sign_extend = <0x00>; tx_data_mode = <0x00>; rx_data_mode = <0x00>; msb_lsb_first = <0x00>; pcm_lrck_period = <0x80>; slot_width_select = <0x20>; asrc_function_en = <0x00>; pinctrl-names = "default", "sleep"; pinctrl-0 = <&daudio2_pins_a &daudio2_pins_b &daudio2_pins_c>; pinctrl-1 = <&daudio2_pins_d>; pinctrl_used = <0x1>; daudio_type = <0x0>; status = "disabled"; }; &sounddaudio2 { status = "disabled"; /* mangopi */ daudio2_master: simple-audio-card,codec { /* sound-dai = <&ac108>; */ }; }; &spdif { pinctrl-names = "default","sleep"; pinctrl-0 = <&spdif_pins_a>; pinctrl-1 = <&spdif_pins_b>; status = "okay"; }; &soundspdif { status = "okay"; }; /* *usb_port_type: usb mode. 0-device, 1-host, 2-otg. *usb_detect_type: usb hotplug detect mode. 0-none, 1-vbus/id detect, 2-id/dpdm detect. *usb_detect_mode: 0-thread scan, 1-id gpio interrupt. *usb_id_gpio: gpio for id detect. *usb_det_vbus_gpio: gpio for id detect. gpio or "axp_ctrl"; *usb_wakeup_suspend：0-SUPER_STANDBY, 1-USB_STANDBY. */ &usbc0 { device_type = "usbc0"; usb_port_type = <0x0>; usb_detect_type = <0x0>; /* usb_detect_mode = <0>; usb_id_gpio = <&pio PB 8 GPIO_ACTIVE_HIGH>; enable-active-high; usb_det_vbus_gpio = <&pio PB 9 GPIO_ACTIVE_HIGH>; */ usb_wakeup_suspend = <0>; usb_serial_unique = <0>; usb_serial_number = "20080411"; rndis_wceis = <1>; status = "okay"; }; &ehci0 { drvvbus-supply = <®_usb1_vbus>; }; &ohci0 { drvvbus-supply = <®_usb1_vbus>; }; &usbc1 { device_type = "usbc1"; usb_port_type = <0x01>; usb_detect_type = <0x1>; usb_regulator_io = "nocare"; usb_wakeup_suspend = <0>; status = "okay"; }; &ehci1 { status = "okay"; }; &ohci1 { status = "okay"; }; &twi0 { clock-frequency = <400000>; pinctrl-0 = <&twi0_pins_a>; pinctrl-1 = <&twi0_pins_b>; pinctrl-names = "default", "sleep"; status = "disabled"; eeprom@50 { compatible = "atmel,24c16"; reg = <0x50>; status = "disabled"; }; }; &twi1 { clock-frequency = <400000>; pinctrl-0 = <&twi1_pins_a>; pinctrl-1 = <&twi1_pins_b>; pinctrl-names = "default", "sleep"; status = "disabled"; }; &twi2 { clock-frequency = <400000>; pinctrl-0 = <&twi2_pins_a>; pinctrl-1 = <&twi2_pins_b>; pinctrl-names = "default", "sleep"; dmas = <&dma 45>, <&dma 45>; dma-names = "tx", "rx"; status = "okay"; /* pcf8574-usage: * only use gpio0~7, 0 means PP0. * pin set: * gpios = <&pcf8574 0 GPIO_ACTIVE_LOW>; * interrupt set: * interrupt-parent = <&pcf8574>; * interrupts = <0 IRQ_TYPE_EDGE_FALLING>; */ pcf8574: gpio@38 { compatible = "nxp,pcf8574"; reg = <0x38>; gpio_base = <2020>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; interrupt-parent = <&pio>; interrupts = <PB 2 IRQ_TYPE_EDGE_FALLING>; status = "disabled"; }; ctp@14 { compatible = "allwinner,goodix"; device_type = "ctp"; reg = <0x14>; status = "okay"; ctp_name = "gt9xxnew_ts"; ctp_twi_id = <0x2>; ctp_twi_addr = <0x14>; ctp_screen_max_x = <0x320>; ctp_screen_max_y = <0x1e0>; ctp_revert_x_flag = <0x0>; ctp_revert_y_flag = <0x0>; ctp_exchange_x_y_flag = <0x0>; ctp_int_port = <&pio PB 3 GPIO_ACTIVE_HIGH>; ctp_wakeup = <&pio PB 2 GPIO_ACTIVE_HIGH>; /*ctp-supply = <®_aldo2>;*/ /*ctp_power_ldo = <®_aldo2>;*/ /*ctp_power_ldo_vol = <3300>;*/ }; }; &twi3 { clock-frequency = <400000>; pinctrl-0 = <&twi3_pins_a>; pinctrl-1 = <&twi3_pins_b>; pinctrl-names = "default", "sleep"; status = "disabled"; }; &gmac0 { phy-mode = "rgmii"; use_ephy25m = <1>; pinctrl-0 = <&gmac_pins_a>; pinctrl-1 = <&gmac_pins_b>; pinctrl-names = "default", "sleep"; phy-rst = <&pio PE 16 GPIO_ACTIVE_HIGH>; tx-delay = <3>; /*2~4*/ rx-delay = <0>; status = "disabled"; }; &spi0 { clock-frequency = <100000000>; pinctrl-0 = <&spi0_pins_a &spi0_pins_b>; pinctrl-1 = <&spi0_pins_c>; pinctrl-names = "default", "sleep"; /*spi-supply = <®_dcdc1>;*/ spi_slave_mode = <0>; spi0_cs_number = <1>; spi0_cs_bitmap = <1>; status = "okay"; spi-nand@0 { compatible = "spi-nand"; spi-max-frequency=<100000000>; reg = <0x0>; spi-rx-bus-width=<0x01>; spi-tx-bus-width=<0x01>; status="okay"; }; spi-nor@0 { compatible = "jedec,spi-nor"; spi-max-frequency=<30000000>; reg = <0x0>; spi-rx-bus-width=<0x01>; spi-tx-bus-width=<0x01>; status="disabled"; }; }; &spi1 { clock-frequency = <100000000>; pinctrl-0 = <&spi1_pins_a &spi1_pins_b>; pinctrl-1 = <&spi1_pins_c>; pinctrl-names = "default", "sleep"; spi_slave_mode = <0>; status = "disabled"; spi_board1@0 { device_type = "spi_board1"; compatible = "rohm,dh2228fv"; spi-max-frequency = <0x5f5e100>; reg = <0x0>; spi-rx-bus-width = <0x4>; spi-tx-bus-width = <0x4>; status = "disabled"; }; }; &ledc { pinctrl-names = "default", "sleep"; pinctrl-0 = <&ledc_pins_a>; pinctrl-1 = <&ledc_pins_b>; led_count = <12>; output_mode = "GRB"; reset_ns = <84>; t1h_ns = <800>; t1l_ns = <320>; t0h_ns = <300>; t0l_ns = <800>; wait_time0_ns = <84>; wait_time1_ns = <84>; wait_data_time_ns = <600000>; status = "disabled"; }; &keyboard0 { key0 = <210 0x160>; wakeup-source; status = "disabled"; }; /*---------------------------------------------------------------------------------- disp init configuration disp_mode (0:screen0<screen0,fb0>) screenx_output_type (0:none; 1:lcd; 2:tv; 5:vdpo) fbx format (4:RGB655 5:RGB565 6:RGB556 7:ARGB1555 8:RGBA5551 9:RGB888 10:ARGB8888 12:ARGB4444) fbx pixel sequence (0:ARGB 1:BGRA 2:ABGR 3:RGBA) fb0_scaler_mode_enable(scaler mode enable, used FE) fbx_width,fbx_height (framebuffer horizontal/vertical pixels, fix to output resolution while equal 0) lcdx_backlight (lcd init backlight,the range:[0,256],default:197 lcdx_yy (lcd init screen bright/contrast/saturation/hue, value:0~100, default:50/50/57/50) lcd0_contrast (LCD contrast, 0~100) lcd0_saturation (LCD saturation, 0~100) lcd0_hue (LCD hue, 0~100) framebuffer software rotation setting: disp_rotation_used: (0:disable; 1:enable,you must set fbX_width to lcd_y, set fbX_height to lcd_x) degreeX: (X:screen index; 0:0 degree; 1:90 degree; 3:270 degree) degreeX_Y: (X:screen index; Y:layer index 0~15; 0:0 degree; 1:90 degree; 3:270 degree) devX_output_type : config output type in bootGUI framework in UBOOT-2018. (0:none; 1:lcd; 2:tv;) devX_output_mode : config output resolution(see include/video/sunxi_display2.h) of bootGUI framework in UBOOT-2018 devX_screen_id : config display index of bootGUI framework in UBOOT-2018 devX_do_hpd : whether do hpd detectation or not in UBOOT-2018 chn_cfg_mode : Hardware DE channel allocation config. 0:single display with 6 channel, 1:dual display with 4 channel in main display and 2 channel in second display, 2:dual display with 3 channel in main display and 3 channel in second in display. ----------------------------------------------------------------------------------*/ &disp { disp_init_enable = <1>; disp_mode = <0>; screen0_output_type = <1>; screen0_output_mode = <4>; screen1_output_type = <3>; screen1_output_mode = <4>; screen1_output_format = <0>; screen1_output_bits = <0>; screen1_output_eotf = <4>; screen1_output_cs = <257>; screen1_output_range = <2>; screen1_output_scan = <0>; screen1_output_aspect_ratio = <8>; dev0_output_type = <1>; dev0_output_mode = <4>; dev0_screen_id = <0>; dev0_do_hpd = <0>; dev1_output_type = <4>; dev1_output_mode = <10>; dev1_screen_id = <1>; dev1_do_hpd = <1>; def_output_dev = <0>; disp_rotation_used = <1>; degree0 = <0>; fb0_format = <0>; fb0_buffer_num = <1>; /*fb0_width = <800>;*/ /*fb0_height = <480>;*/ /*read from lcd*/ fb1_format = <0>; fb1_width = <0>; fb1_height = <0>; chn_cfg_mode = <1>; disp_para_zone = <1>; /*VCC-LCD*/ /* dc1sw-supply = <®_dc1sw>;*/ /*VCC-DSI*/ /* eldo3-supply = <®_eldo3>;*/ /*VCC-PD*/ /* dcdc1-supply = <®_dcdc1>;*/ }; /*---------------------------------------------------------------------------------- ;lcd0 configuration ;lcd_if: 0:hv(sync+de); 1:8080; 2:ttl; 3:lvds; 4:dsi; 5:edp; 6:extend dsi ;lcd_hv_if 0:Parallel RGB; 8:Serial RGB; 10:Dummy RGB; 11: RGB Dummy;12:CCIR656 ;lcd_hv_clk_phase 0:0 degree;1:90 degree;2:180 degree;3:270 degree ;lcd_hv_sync_polarity 0:vs low,hs low; 1:vs high,hslow; 2:vs low,hs high; 3:vs high,hs high ;lcd_hv_syuv_seq 0:YUYV; 1:YVYU; 2:UYVY; 3:VYUY ;lcd_cpu_if 0:18bit/1 cycle parallel(RGB666); 4:16bit/1cycle parallel (RGB565) ; 6:18bit/3 cycle parallel(RGB666); 7:16bit/2cycle parallel (RGB565) ;lcd_cpu_te 0:frame auto trigger; 1:frame triggered by te rising edge; 2:frame triggered by te falling edge; ;lcd_dsi_if 0:video mode; 1: Command mode; 2:video burst mode ;lcd_dsi_te 0:frame auto trigger; 1:frame triggered by te rising edge; 2:frame triggered by te falling edge; ;lcd_x: lcd horizontal resolution ;lcd_y: lcd vertical resolution ;lcd_width: width of lcd in mm ;lcd_height: height of lcd in mm ;lcd_dclk_freq: in MHZ unit ;lcd_pwm_freq: in HZ unit ;lcd_pwm_pol: lcd backlight PWM polarity ;lcd_pwm_max_limit lcd backlight PWM max limit(<=255) ;lcd_hbp: hsync back porch(pixel) + hsync plus width(pixel); ;lcd_ht: hsync total cycle(pixel) ;lcd_vbp: vsync back porch(line) + vysnc plus width(line) ;lcd_vt: vysnc total cycle(line) ;lcd_hspw: hsync plus width(pixel) ;lcd_vspw: vysnc plus width(pixel) ;lcd_lvds_if: 0:single link; 1:dual link ;lcd_lvds_colordepth: 0:8bit; 1:6bit ;lcd_lvds_mode: 0:NS mode; 1:JEIDA mode ;lcd_frm: 0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither ;lcd_io_phase: 0:noraml; 1:intert phase(0~3bit: vsync phase; 4~7bit:hsync phase; ; 8~11bit:dclk phase; 12~15bit:de phase) ;lcd_gamma_en lcd gamma correction enable ;lcd_bright_curve_en lcd bright curve correction enable ;lcd_cmap_en lcd color map function enable ;deu_mode 0:smoll lcd screen; 1:large lcd screen(larger than 10inch) ;lcdgamma4iep: Smart Backlight parameter, lcd gamma vale * 10; ; decrease it while lcd is not bright enough; increase while lcd is too bright ;smart_color 90:normal lcd screen 65:retina lcd screen(9.7inch) ;Pin setting for special function ie.LVDS, RGB data or vsync ; name(donot care) = port:PD12<pin function><pull up or pull down><drive ability><output level> ;Pin setting for gpio: ; lcd_gpio_X = port:PD12<pin function><pull up or pull down><drive ability><output level> ;Pin setting for backlight enable pin ; lcd_bl_en = port:PD12<pin function><pull up or pull down><drive ability><output level> ;fsync setting, pulse to csi ;lcd_fsync_en (0:disable fsync,1:enable) ;lcd_fsync_act_time (active time of fsync, unit:pixel) ;lcd_fsync_dis_time (disactive time of fsync, unit:pixel) ;lcd_fsync_pol (0:positive;1:negative) ;gpio config: <&pio for cpu or &r_pio for cpus, port, port num, pio function, pull up or pull down(default 0), driver level(default 1), data> ;For dual link lvds: use lvds2link_pins_a and lvds2link_pins_b instead ;For rgb24: use rgb24_pins_a and rgb24_pins_b instead ;For lvds1: use lvds1_pins_a and lvds1_pins_b instead ;For lvds0: use lvds0_pins_a and lvds0_pins_b instead ;----------------------------------------------------------------------------------*/ /* &lcd0 { lcd_used = <0>; lcd_driver_name = "tft08006"; lcd_backlight = <100>; lcd_if = <4>; lcd_x = <800>; lcd_y = <1280>; lcd_width = <52>; lcd_height = <52>; lcd_dclk_freq = <70>; lcd_pwm_used = <1>; lcd_pwm_ch = <2>; lcd_pwm_freq = <1000>; lcd_pwm_pol = <0>; lcd_pwm_max_limit = <255>; lcd_hbp = <32>; lcd_ht = <868>; lcd_hspw = <4>; lcd_vbp = <12>; lcd_vt = <1311>; lcd_vspw = <4>; lcd_dsi_if = <0>; lcd_dsi_lane = <4>; lcd_lvds_if = <0>; lcd_lvds_colordepth = <0>; lcd_lvds_mode = <0>; lcd_frm = <0>; lcd_hv_clk_phase = <0>; lcd_hv_sync_polarity= <0>; lcd_io_phase = <0x0000>; lcd_gamma_en = <0>; lcd_bright_curve_en = <0>; lcd_cmap_en = <0>; lcd_fsync_en = <0>; lcd_fsync_act_time = <1000>; lcd_fsync_dis_time = <1000>; lcd_fsync_pol = <0>; deu_mode = <0>; lcdgamma4iep = <22>; smart_color = <90>; lcd_gpio_0 = <&pio PG 13 GPIO_ACTIVE_HIGH>; pinctrl-0 = <&dsi4lane_pins_a>; pinctrl-1 = <&dsi4lane_pins_b>; }; */ &lcd0 { lcd_used = <1>; lcd_driver_name = "default_lcd"; lcd_backlight = <50>; lcd_if = <0>; lcd_x = <800>; lcd_y = <480>; lcd_width = <150>; lcd_height = <94>; lcd_dclk_freq = <48>; lcd_pwm_used = <1>; lcd_pwm_ch = <7>; lcd_pwm_freq = <500>; lcd_pwm_pol = <0>; lcd_hbp = <55>; lcd_ht = <1240>; lcd_hspw = <20>; lcd_vbp = <35>; lcd_vt = <650>; lcd_vspw = <10>; lcd_lvds_if = <0>; lcd_lvds_colordepth = <1>; lcd_lvds_mode = <0>; lcd_frm = <0>; lcd_io_phase = <0x0000>; lcd_gamma_en = <0>; lcd_bright_curve_en = <0>; lcd_cmap_en = <0>; deu_mode = <0>; lcdgamma4iep = <22>; smart_color = <90>; pinctrl-0 = <&rgb18_pins_a>; pinctrl-1 = <&rgb18_pins_b>; /* lcd_driver_name = "default_lcd"; lcd_backlight = <150>; lcd_if = <3>; lcd_x = <1280>; lcd_y = <800>; lcd_width = <150>; lcd_height = <94>; lcd_dclk_freq = <71>; lcd_rb_swap = <0>; lcd_pwm_used = <1>; lcd_pwm_ch = <7>; lcd_pwm_freq = <50000>; lcd_pwm_pol = <1>; lcd_pwm_max_limit = <255>; lcd_hbp = <20>; lcd_ht = <1418>; lcd_hspw = <10>; lcd_vbp = <10>; lcd_vt = <814>; lcd_vspw = <5>; lcd_lvds_if = <0>; lcd_lvds_colordepth = <1>; lcd_lvds_mode = <0>; lcd_frm = <1>; lcd_io_phase = <0x0000>; lcd_hv_clk_phase = <0>; lcd_hv_sync_polarity = <0>; lcd_gamma_en = <0>; lcd_bright_curve_en = <0>; lcd_cmap_en = <0>; lcd_fsync_act_time = <1000>; lcd_fsync_dis_time = <1000>; deu_mode = <0>; lcdgamma4iep = <22>; smart_color = <90>; pinctrl-0 = <&lvds0_pins_a>; pinctrl-1 = <&lvds0_pins_b>; lcd_bl_en = <&pio PD 20 GPIO_ACTIVE_HIGH>; lcd_driver_name = "he0801a068"; lcd_backlight = <50>; lcd_if = <4>; lcd_x = <800>; lcd_y = <1280>; lcd_width = <52>; lcd_height = <52>; lcd_dclk_freq = <78>; lcd_pwm_used = <1>; lcd_pwm_ch = <7>; lcd_pwm_freq = <50000>; lcd_pwm_pol = <1>; lcd_pwm_max_limit = <255>; lcd_hbp = <149>; lcd_ht = <978>; lcd_hspw = <16>; lcd_vbp = <7>; lcd_vt = <1329>; lcd_vspw = <5>; lcd_dsi_lane = <4>; lcd_lvds_if = <0>; lcd_lvds_colordepth = <1>; lcd_lvds_mode = <0>; lcd_frm = <0>; lcd_io_phase = <0x0000>; lcd_gamma_en = <0>; lcd_bright_curve_en = <0>; lcd_cmap_en = <0>; lcd_fsync_act_time = <1000>; lcd_fsync_dis_time = <1000>; deu_mode = <0>; lcdgamma4iep = <22>; smart_color = <90>; pinctrl-0 = <&dsi4lane_pins_a>; pinctrl-1 = <&dsi4lane_pins_b>; lcd_gpio_0 = <&pio PD 20 GPIO_ACTIVE_HIGH>; */ }; &pwm0 { pinctrl-names = "active", "sleep"; pinctrl-0 = <&pwm0_pin_a>; pinctrl-1 = <&pwm0_pin_b>; status = "disabled"; }; &pwm2 { pinctrl-names = "active", "sleep"; pinctrl-0 = <&pwm2_pin_a>; pinctrl-1 = <&pwm2_pin_b>; status = "disabled"; }; &pwm7 { pinctrl-names = "active", "sleep"; pinctrl-0 = <&pwm7_pin_a>; pinctrl-1 = <&pwm7_pin_b>; status = "disabled"; }; &rtp { allwinner,tp-sensitive-adjust = <0xf>; allwinner,filter-type = <0x1>; allwinner,ts-attached; status = "disabled"; }; &tpadc { key_cnt = <5>; key1 = <420 115>; key2 = <870 114>; key3 = <1290 119>; key4 = <1630 373>; key5 = <1950 28>; status = "disabled"; }; &gpadc { channel_num = <1>; channel_select = <0x01>; channel_data_select = <0>; channel_compare_select = <0x01>; channel_cld_select = <0x01>; channel_chd_select = <0>; channel0_compare_lowdata = <1600000>; channel0_compare_higdata = <1200000>; channel1_compare_lowdata = <460000>; channel1_compare_higdata = <1200000>; key_cnt = <5>; key0_vol = <210>; key0_val = <0x19c>; key1_vol = <410>; key1_val = <0x197>; key2_vol = <590>; key2_val = <158>; key3_vol = <750>; key3_val = <28>; key4_vol = <880>; key4_val = <28>; status = "okay"; wakeup-source; }; &s_cir0 { pinctrl-names = "default", "sleep"; pinctrl-0 = <&s_cir0_pins_a>; pinctrl-1 = <&s_cir0_pins_b>; ir_protocol_used = <0>; ir_addr_code0 = <0x0>; status = "disabled"; }; &ir1 { pinctrl-names = "default", "sleep"; pinctrl-0 = <&ir1_pins_a>; pinctrl-1 = <&ir1_pins_b>; status = "disabled"; };sun8iw20p1.dtsi
/* * Allwinner Technology CO., Ltd. sun8iw20p1 platform * * modify base on juno.dts */ /* optee used 7MB: SHM 2M: OS: 1M: TA:4M*/ /memreserve/ 0x41900000 0x00700000; #include <dt-bindings/clock/sun8iw20-ccu.h> #include <dt-bindings/clock/sun8iw20-r-ccu.h> #include <dt-bindings/clock/sun8iw20-rtc.h> #include <dt-bindings/reset/sun8iw20-ccu.h> #include <dt-bindings/reset/sun8iw20-r-ccu.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/gpio/sun4i-gpio.h> #include <dt-bindings/thermal/thermal.h> #include <dt-bindings/power/r528-power.h> / { model = "sun8iw20"; compatible = "allwinner,sun8iw20p1"; interrupt-parent = <&gic>; #address-cells = <2>; #size-cells = <2>; aliases { serial0 = &uart0; serial1 = &uart1; serial2 = &uart2; serial3 = &uart3; serial4 = &uart4; serial5 = &uart5; spi0 = &spi0; spi1 = &spi1; twi0 = &twi0; twi1 = &twi1; twi2 = &twi2; twi3 = &twi3; mmc0 = &sdc0; mmc2 = &sdc2; pwm = &pwm; pwm0 = &pwm0; pwm1 = &pwm1; pwm2 = &pwm2; pwm3 = &pwm3; pwm4 = &pwm4; pwm5 = &pwm5; pwm6 = &pwm6; pwm7 = &pwm7; ir0 = &s_cir0; ve0 = &ve; tv0 = &tv0; tvd = &tvd; tvd0 = &tvd0; share_space0 = &share_space0; }; chosen { bootargs = "earlyprintk=sunxi-uart,0x2500000 loglevel=8 initcall_debug=0 console=ttyS0 init=/init"; //bootargs = "loglevel=8 initcall_debug=0 console=ttyS0 init=/init"; linux,initrd-start = <0x0 0x0>; linux,initrd-end = <0x0 0x0>; }; firmware { optee { compatible = "linaro,optee-tz"; method = "smc"; }; }; cpus { enable-method = "allwinner,sun8iw20p1"; #address-cells = <1>; #size-cells = <0>; cpu0: cpu@0 { device_type = "cpu"; compatible = "arm,cortex-a7","arm,armv7"; reg = <0x0>; enable-method = "psci"; clocks = <&ccu CLK_CPUX>; dynamic-power-coefficient = <156>; cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>; operating-points-v2 = <&cpu_opp_table>; #cooling-cells = <2>; }; cpu1: cpu@1 { device_type = "cpu"; compatible = "arm,cortex-a7","arm,armv7"; reg = <0x1>; enable-method = "psci"; clocks = <&ccu CLK_CPUX>; cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>; operating-points-v2 = <&cpu_opp_table>; #cooling-cells = <2>; }; idle-states { entry-method = "arm,psci"; CPU_SLEEP: cpu-sleep { compatible = "arm,idle-state"; arm,psci-suspend-param = <0x0010000>; entry-latency-us = <46>; exit-latency-us = <59>; min-residency-us = <3570>; local-timer-stop; }; CLUSTER_SLEEP: cluster-sleep { compatible = "arm,idle-state"; arm,psci-suspend-param = <0x1010000>; entry-latency-us = <47>; exit-latency-us = <74>; min-residency-us = <5000>; local-timer-stop; }; }; }; psci { compatible = "arm,psci-1.0"; method = "smc"; }; dump_reg: dump_reg@20000 { compatible = "allwinner,sunxi-dump-reg"; reg = <0x0 0x00020000 0x0 0x0004>; /* 0x00020000: dump_reg test addr, 0x0004: dump_reg test size */ }; cpu_opp_table: cpu-opp-table { compatible = "allwinner,sun50i-operating-points"; nvmem-cells = <&speedbin_efuse>, <&cpubin_efuse>; nvmem-cell-names = "speed", "bin"; opp-shared; opp@480000000 { opp-hz = /bits/ 64 <480000000>; clock-latency-ns = <244144>; /* 8 32k periods */ opp-microvolt-a0 = <900000>; opp-microvolt-a1 = <900000>; opp-microvolt-b0 = <950000>; opp-supported-hw = <0x3>; }; opp@720000000 { opp-hz = /bits/ 64 <720000000>; clock-latency-ns = <244144>; /* 8 32k periods */ opp-microvolt-a0 = <900000>; opp-microvolt-a1 = <900000>; opp-microvolt-b0 = <950000>; opp-supported-hw = <0x3>; }; opp@912000000 { opp-hz = /bits/ 64 <912000000>; clock-latency-ns = <244144>; /* 8 32k periods */ opp-microvolt-a0 = <950000>; opp-microvolt-a1 = <900000>; opp-microvolt-b0 = <950000>; opp-supported-hw = <0x3>; }; opp@1008000000 { opp-hz = /bits/ 64 <1008000000>; clock-latency-ns = <244144>; /* 8 32k periods */ opp-microvolt-a0 = <1000000>; opp-microvolt-a1 = <900000>; opp-microvolt-b0 = <950000>; opp-supported-hw = <0x3>; }; opp@1104000000 { opp-hz = /bits/ 64 <1104000000>; clock-latency-ns = <244144>; /* 8 32k periods */ opp-microvolt-a0 = <1050000>; opp-microvolt-a1 = <950000>; opp-microvolt-b0 = <950000>; opp-supported-hw = <0x3>; }; opp@1200000000 { opp-hz = /bits/ 64 <1200000000>; clock-latency-ns = <244144>; /* 8 32k periods */ opp-microvolt-a0 = <1100000>; opp-microvolt-a1 = <1000000>; opp-supported-hw = <0x1>; }; }; dcxo24M: dcxo24M_clk { #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <24000000>; clock-output-names = "dcxo24M"; }; rc_16m: rc16m_clk { #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <16000000>; clock-accuracy = <300000000>; clock-output-names = "rc-16m"; }; ext_32k: ext32k_clk { #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <32768>; clock-output-names = "ext-32k"; }; dram: dram { compatible = "allwinner,dram"; clocks = <&ccu CLK_PLL_DDR0>; clock-names = "pll_ddr"; }; memory@40000000 { device_type = "memory"; reg = <0x00000000 0x40000000 0x00000000 0x20000000>; }; share_space0: share_space@42100000 { #address-cells = <1>; #size-cells = <1>; deice_tpye = "share_space0"; /* dsp write addr and len */ /* arm write addr and len */ /* dsp log addr and len */ /* reserve */ reg = < 0x42100000 0x00001000 0x42101000 0x00001000 0x42102000 0x0000E000 0x00000000 0x00000000>; }; gic: interrupt-controller@3020000 { compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic"; #interrupt-cells = <3>; #address-cells = <0>; device_type = "gic"; interrupt-controller; reg = <0x0 0x03021000 0 0x1000>, /* GIC Dist */ <0x0 0x03022000 0 0x2000>, /* GIC CPU */ <0x0 0x03024000 0 0x2000>, /* GIC VCPU Control */ <0x0 0x03026000 0 0x2000>; /* GIC VCPU */ interrupts = <GIC_PPI 9 0xf04>; /* GIC Maintenence IRQ */ }; timer_arch { compatible = "arm,armv7-timer"; interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>; clock-frequency = <24000000>; arm,cpu-registers-not-fw-configured; interrupt-parent = <&gic>; arm,no-tick-in-suspend; }; pmu { compatible = "arm,cortex-a7-pmu"; interrupts = <GIC_SPI 172 4>, <GIC_SPI 173 4>; }; power: power-management@ff000000 { compatible = "allwinner,r528-pmu", "syscon", "simple-mfd"; reg = <0x0 0x07001000 0x0 0x400>; pd: power-controller { compatible = "allwinner,r528-power-controller"; clocks = <&r_ccu CLK_R_PPU>; clock-names = "ppu"; resets = <&r_ccu RST_R_PPU>; reset-names = "ppu_rst"; #power-domain-cells = <1>; #address-cells = <1>; #size-cells = <0>; /* These power domains are grouped by VD_SYS */ pd_ve@R528_PD_VE { reg = <R528_PD_VE>; }; }; }; mmu_aw: iommu@2010000 { compatible = "allwinner,sunxi-iommu"; reg = <0x0 0x02010000 0x0 0x1000>; interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "iommu-irq"; clocks = <&ccu CLK_BUS_IOMMU>; clock-names = "iommu"; #iommu-cells = <2>; status = "okay"; }; reg_pio1_8: pio-18 { compatible = "regulator-fixed"; regulator-name = "pio-18"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; reg_pio3_3: pio-33 { compatible = "regulator-fixed"; regulator-name = "pio-33"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; thermal-zones { cpu_thermal_zone { polling-delay-passive = <500>; polling-delay = <1000>; thermal-sensors = <&ths 0>; sustainable-power = <589>; cpu_trips: trips { cpu_threshold: trip-point@0 { temperature = <70000>; type = "passive"; hysteresis = <0>; }; cpu_target: trip-point@1 { temperature = <90000>; type = "passive"; hysteresis = <0>; }; cpu_crit: cpu_crit@0 { temperature = <110000>; type = "critical"; hysteresis = <0>; }; }; cooling-maps { map0 { trip = <&cpu_target>; cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; contribution = <1024>; }; }; }; }; soc: soc@3000000 { compatible = "simple-bus"; #address-cells = <2>; #size-cells = <2>; ranges; device_type = "soc"; sram_ctrl: sram_ctrl@3000000 { compatible = "allwinner,sram_ctrl"; reg = <0x0 0x3000000 0 0x16C>; soc_ver { offset = <0x24>; mask = <0x7>; shift = <0>; ver_a = <0x18590000>; ver_b = <0x18590002>; ver_d = <0x18590003>; }; soc_id { offset = <0x200>; mask = <0x1>; shift = <22>; }; soc_bin { offset = <0x0>; mask = <0x3ff>; shift = <0x0>; }; }; rtc_ccu: rtc_ccu@7090000 { compatible = "allwinner,sun8iw20-rtc-ccu"; device_type = "rtc-ccu"; reg = <0x0 0x07090000 0x0 0x320>; /* The same as rtc */ #clock-cells = <1>; }; ccu: ccu@2001000 { compatible = "allwinner,sun8iw20-ccu"; reg = <0x0 0x02001000 0x0 0x1000>; clocks = <&dcxo24M>, <&rtc_ccu CLK_OSC32K>, <&rtc_ccu CLK_IOSC>; clock-names = "hosc", "losc", "iosc"; #clock-cells = <1>; #reset-cells = <1>; }; r_ccu: r_ccu@7010000 { compatible = "allwinner,sun8iw20-r-ccu"; reg = <0x0 0x07010000 0x0 0x240>; clocks = <&dcxo24M>, <&rtc_ccu CLK_OSC32K>, <&rtc_ccu CLK_IOSC>, <&ccu CLK_PLL_PERIPH0>; clock-names = "hosc", "losc", "iosc", "pll-periph0"; #clock-cells = <1>; #reset-cells = <1>; }; rtc: rtc@7090000 { compatible = "allwinner,sun8iw20-rtc"; device_type = "rtc"; wakeup-source; reg = <0x0 0x07090000 0x0 0x320>; interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>; clocks = <&r_ccu CLK_R_AHB_BUS_RTC>, <&rtc_ccu CLK_RTC_1K>, <&rtc_ccu CLK_RTC_SPI>; clock-names = "r-ahb-rtc", "rtc-1k", "rtc-spi"; resets = <&r_ccu RST_R_AHB_BUS_RTC>; gpr_cur_pos = <6>; }; dma:dma-controller@3002000 { compatible = "allwinner,sun8iw20-dma"; reg = <0x0 0x03002000 0x0 0x1000>; interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>; clock-names = "bus", "mbus"; dma-channels = <8>; dma-requests = <48>; resets = <&ccu RST_BUS_DMA>; #dma-cells = <1>; }; soc_timer0: timer@2050000 { compatible = "allwinner,sun4i-a10-timer"; device_type = "soc_timer"; reg = <0x0 0x02050000 0x0 0xA0>; interrupt-parent = <&gic>; interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; clocks = <&dcxo24M>; }; wdt: watchdog@20500A0 { compatible = "allwinner,sun6i-a31-wdt"; reg = <0x0 0x020500A0 0x0 0x20>; /* In Timers Spec */ interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; /* In GIC Spec */ }; mbus0: mbus-controller@3102000 { compatible = "allwinner,sun8i-mbus"; reg = <0x0 0x03102000 0x0 0x1000>; /* In SDRAM Controller Spec: DRAMC Common Register */ #mbus-cells = <1>; }; pio: pinctrl@2000000 { compatible = "allwinner,sun8iw20-pinctrl"; reg = <0x0 0x02000000 0x0 0x500>; interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, /* AW1859_GIC_Spec: GPIOB: 101-32=69 */ <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; device_type = "pio"; clocks = <&ccu CLK_APB0>, <&dcxo24M>, <&rtc_ccu CLK_OSC32K>; clock-names = "apb", "hosc", "losc"; gpio-controller; #gpio-cells = <3>; interrupt-controller; #interrupt-cells = <3>; #size-cells = <0>; vcc-pf-supply = <®_pio1_8>; vcc-pfo-supply = <®_pio3_3>; test_pins_a: test_pins@0 { allwinner,pins = "PB0", "PB1"; allwinner,function = "test"; allwinner,muxsel = <0x9>; allwinner,drive = <1>; allwinner,pull = <1>; }; test_pins_b: test_pins@1 { pins = "PB0", "PB1"; function = "io_disabled"; allwinner,muxsel = <0xF>; allwinner,drive = <1>; allwinner,pull = <1>; }; csi_mclk0_pins_a: csi_mclk0@0 { pins = "PE3"; function = "csi0"; drive-strength = <10>; }; csi_mclk0_pins_b: csi_mclk0@1 { pins = "PE3"; function = "gpio_in"; }; csi0_pins_a: csi0@0 { pins = "PE2", "PE0", "PE1", "PE4", "PE5", "PE6", "PE7", "PE8", "PE9", "PE10", "PE11"; function = "ncsi0"; drive-strength = <10>; }; csi0_pins_b: csi0@1 { pins = "PE2", "PE0", "PE1", "PE4", "PE5", "PE6", "PE7", "PE8", "PE9", "PE10", "PE11"; function = "io_disabled"; drive-strength = <10>; }; lvds0_pins_a: lvds0@0 { pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5", "PD6", "PD7", "PD8", "PD9"; function = "lvds0"; drive-strength = <30>; bias-disable; }; lvds0_pins_b: lvds0@1 { pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5", "PD6", "PD7", "PD8", "PD9"; function = "io_disabled"; drive-strength = <30>; bias-disable; }; rgb24_pins_a: rgb24@0 { pins = "PB2", "PB3", "PD0", "PD1", "PD2", "PD3", "PD4", "PD5", \ "PB4", "PB5", "PD6", "PD7", "PD8", "PD9", "PD10", "PD11", \ "PB6", "PB7", "PD12", "PD13", "PD14", "PD15", "PD16", "PD17", \ "PD18", "PD19", "PD20", "PD21"; function = "lcd0"; drive-strength = <30>; bias-disable; }; rgb24_pins_b: rgb24@1 { pins = "PB2", "PB3", "PD0", "PD1", "PD2", "PD3", "PD4", "PD5", \ "PB4", "PB5", "PD6", "PD7", "PD8", "PD9", "PD10", "PD11", \ "PB6", "PB7", "PD12", "PD13", "PD14", "PD15", "PD16", "PD17", \ "PD18", "PD19", "PD20", "PD21"; function = "io_disabled"; bias-disable; }; rgb18_pins_a: rgb18@0 { pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5", \ "PD6", "PD7", "PD8", "PD9", "PD10", "PD11", \ "PD12", "PD13", "PD14", "PD15", "PD16", "PD17", \ "PD18", "PD19", "PD20", "PD21"; function = "lcd0"; drive-strength = <30>; bias-disable; }; rgb18_pins_b: rgb18@1 { pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5", \ "PD6", "PD7", "PD8", "PD9", "PD10", "PD11", \ "PD12", "PD13", "PD14", "PD15", "PD16", "PD17", \ "PD18", "PD19", "PD20", "PD21"; function = "io_disabled"; bias-disable; }; dsi2lane_pins_a: dsi2lane@0 { pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5"; function = "dsi"; drive-strength = <30>; bias-disable; }; dsi2lane_pins_b: dsi2lane@1 { pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5"; function = "io_disabled"; bias-disable; }; dsi4lane_pins_a: dsi4lane@0 { pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5", "PD6", "PD7", "PD8", "PD9"; function = "dsi"; drive-strength = <30>; bias-disable; }; dsi4lane_pins_b: dsi4lane@1 { pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5", "PD6", "PD7", "PD8", "PD9"; function = "io_disabled"; bias-disable; }; }; pinctrl_test: pinctrl_test@0 { reg = <0x0 0x0 0x0 0x0>; compatible = "allwinner,sunxi-pinctrl-test"; device_type = "pinctrl-test"; /* For pin state selecting test */ pinctrl-0 = <&test_pins_a>; pinctrl-1 = <&test_pins_b>; pinctrl-names = "default", "sleep"; /* For pin basic_function/irq test */ test-gpios = <&pio PB 0 GPIO_ACTIVE_LOW>; interrupt-parent = <&pio>; interrupts = <PB 1 IRQ_TYPE_LEVEL_HIGH>; }; uart0: uart@2500000 { compatible = "allwinner,sun8i-uart"; device_type = "uart0"; reg = <0x0 0x02500000 0x0 0x400>; interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; sunxi,uart-fifosize = <64>; clocks = <&ccu CLK_BUS_UART0>; clock-names = "uart0"; resets = <&ccu RST_BUS_UART0>; uart0_port = <0>; uart0_type = <2>; status = "disabled"; }; uart1: uart@2500400 { compatible = "allwinner,sun8i-uart"; device_type = "uart1"; reg = <0x0 0x02500400 0x0 0x400>; interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; sunxi,uart-fifosize = <256>; clocks = <&ccu CLK_BUS_UART1>; clock-names = "uart1"; resets = <&ccu RST_BUS_UART1>; uart1_port = <1>; uart1_type = <4>; status = "okay"; }; uart2: uart@2500800 { compatible = "allwinner,sun8i-uart"; device_type = "uart2"; reg = <0x0 0x02500800 0x0 0x400>; interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; sunxi,uart-fifosize = <256>; clocks = <&ccu CLK_BUS_UART2>; clock-names = "uart2"; resets = <&ccu RST_BUS_UART2>; uart2_port = <2>; uart2_type = <4>; status = "disabled"; }; uart3: uart@2500c00 { compatible = "allwinner,sun8i-uart"; device_type = "uart3"; reg = <0x0 0x02500c00 0x0 0x400>; interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; sunxi,uart-fifosize = <256>; clocks = <&ccu CLK_BUS_UART3>; clock-names = "uart3"; resets = <&ccu RST_BUS_UART3>; uart3_port = <3>; uart3_type = <4>; status = "disabled"; }; uart4: uart@2501000 { compatible = "allwinner,sun8i-uart"; device_type = "uart4"; reg = <0x0 0x02501000 0x0 0x400>; interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; sunxi,uart-fifosize = <256>; clocks = <&ccu CLK_BUS_UART4>; clock-names = "uart4"; resets = <&ccu RST_BUS_UART4>; uart4_port = <4>; uart4_type = <2>; status = "disabled"; }; uart5: uart@2501400 { compatible = "allwinner,sun8i-uart"; device_type = "uart5"; reg = <0x0 0x02501400 0x0 0x400>; interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; sunxi,uart-fifosize = <256>; clocks = <&ccu CLK_BUS_UART5>; clock-names = "uart5"; resets = <&ccu RST_BUS_UART5>; uart5_port = <5>; uart5_type = <2>; status = "disabled"; }; cryptoengine: ce@03040000 { compatible = "allwinner,sunxi-ce"; device_name = "ce"; reg = <0x0 0x03040000 0x0 0xa0>, /* non-secure space */ <0x0 0x03040800 0x0 0xa0>; /* secure space */ interrupts = <GIC_SPI 52 IRQ_TYPE_EDGE_RISING>, /*non-secure*/ <GIC_SPI 53 IRQ_TYPE_EDGE_RISING>; /* secure*/ clock-frequency = <400000000>; /* 400MHz */ clocks = <&ccu CLK_BUS_CE>, <&ccu CLK_CE>, <&ccu CLK_MBUS_CE>, <&ccu CLK_PLL_PERIPH0_2X>; clock-names = "bus_ce", "ce_clk", "mbus_ce", "pll_periph0_2x"; resets = <&ccu RST_BUS_CE>; status = "okay"; }; gmac0: eth@4500000 { compatible = "allwinner,sunxi-gmac"; reg = <0x0 0x04500000 0x0 0x10000>, <0x0 0x03000030 0x0 0x4>; interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "gmacirq"; clocks = <&ccu CLK_BUS_EMAC0>, <&ccu CLK_EMAC0_25M>; clock-names = "gmac", "ephy"; resets = <&ccu RST_BUS_EMAC0>; device_type = "gmac0"; gmac-power0; gmac-power1; gmac-power2; status = "disabled"; }; sdc2: sdmmc@4022000 { compatible = "allwinner,sunxi-mmc-v4p6x"; device_type = "sdc2"; reg = <0x0 0x04022000 0x0 0x1000>; interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; clocks = <&dcxo24M>, <&ccu CLK_PLL_PERIPH0_2X>, <&ccu CLK_MMC2>, <&ccu CLK_BUS_MMC2>; clock-names = "osc24m","pll_periph","mmc","ahb"; resets = <&ccu RST_BUS_MMC2>; reset-names = "rst"; pinctrl-names = "default","sleep"; pinctrl-0 = <&sdc2_pins_a>; pinctrl-1 = <&sdc2_pins_b>; bus-width = <4>; req-page-count = <2>; cap-mmc-highspeed; cap-cmd23; mmc-cache-ctrl; non-removable; /*max-frequency = <200000000>;*/ max-frequency = <50000000>; cap-erase; mmc-high-capacity-erase-size; no-sdio; no-sd; /*-- speed mode --*/ /*sm0: DS26_SDR12*/ /*sm1: HSSDR52_SDR25*/ /*sm2: HSDDR52_DDR50*/ /*sm3: HS200_SDR104*/ /*sm4: HS400*/ /*-- frequency point --*/ /*f0: CLK_400K*/ /*f1: CLK_25M*/ /*f2: CLK_50M*/ /*f3: CLK_100M*/ /*f4: CLK_150M*/ /*f5: CLK_200M*/ sdc_tm4_sm0_freq0 = <0>; sdc_tm4_sm0_freq1 = <0>; sdc_tm4_sm1_freq0 = <0x00000000>; sdc_tm4_sm1_freq1 = <0>; sdc_tm4_sm2_freq0 = <0x00000000>; sdc_tm4_sm2_freq1 = <0>; sdc_tm4_sm3_freq0 = <0x05000000>; sdc_tm4_sm3_freq1 = <0x00000005>; sdc_tm4_sm4_freq0 = <0x00050000>; sdc_tm4_sm4_freq1 = <0x00000004>; sdc_tm4_sm4_freq0_cmd = <0>; sdc_tm4_sm4_freq1_cmd = <0>; /*vmmc-supply = <®_3p3v>;*/ /*vqmc-supply = <®_3p3v>;*/ /*vdmc-supply = <®_3p3v>;*/ /*vmmc = "vcc-card";*/ /*vqmc = "";*/ /*vdmc = "";*/ /*sunxi-power-save-mode;*/ }; sdc0: sdmmc@4020000 { compatible = "allwinner,sunxi-mmc-v5p3x"; device_type = "sdc0"; reg = <0x0 0x04020000 0x0 0x1000>; interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; clocks = <&dcxo24M>, <&ccu CLK_PLL_PERIPH0_2X>, <&ccu CLK_MMC0>, <&ccu CLK_BUS_MMC0>; clock-names = "osc24m","pll_periph","mmc","ahb"; resets = <&ccu RST_BUS_MMC0>; reset-names = "rst"; pinctrl-names = "default","mmc_1v8","sleep","uart_jtag"; pinctrl-0 = <&sdc0_pins_a>; pinctrl-1 = <&sdc0_pins_b>; pinctrl-2 = <&sdc0_pins_c>; pinctrl-3 = <&sdc0_pins_d &sdc0_pins_e>; max-frequency = <50000000>; bus-width = <4>; req-page-count = <2>; /*non-removable;*/ /*broken-cd;*/ /*cd-inverted*/ /*cd-gpios = <&pio PF 6 GPIO_ACTIVE_LOW>;*/ /* vmmc-supply = <®_3p3v>;*/ /* vqmc-supply = <®_3p3v>;*/ /* vdmc-supply = <®_3p3v>;*/ /*vmmc = "vcc-card";*/ /*vqmc = "";*/ /*vdmc = "";*/ cap-sd-highspeed; cap-wait-while-busy; no-sdio; no-mmc; /*sd-uhs-sdr50;*/ /*sd-uhs-ddr50;*/ /*cap-sdio-irq;*/ /*keep-power-in-suspend;*/ /*ignore-pm-notify;*/ /*sunxi-power-save-mode;*/ /*sunxi-dly-400k = <1 0 0 0>; */ /*sunxi-dly-26M = <1 0 0 0>;*/ /*sunxi-dly-52M = <1 0 0 0>;*/ /*sunxi-dly-52M-ddr4 = <1 0 0 0>;*/ /*sunxi-dly-52M-ddr8 = <1 0 0 0>;*/ /*sunxi-dly-104M = <1 0 0 0>;*/ /*sunxi-dly-208M = <1 0 0 0>;*/ /*sunxi-dly-104M-ddr = <1 0 0 0>;*/ /*sunxi-dly-208M-ddr = <1 0 0 0>;*/ }; sdc1: sdmmc@4021000 { compatible = "allwinner,sunxi-mmc-v5p3x"; device_type = "sdc1"; reg = <0x0 0x04021000 0x0 0x1000>; interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; clocks = <&dcxo24M>, <&ccu CLK_PLL_PERIPH0_2X>, <&ccu CLK_MMC1>, <&ccu CLK_BUS_MMC1>; clock-names = "osc24m","pll_periph","mmc","ahb"; resets = <&ccu RST_BUS_MMC1>; reset-names = "rst"; pinctrl-names = "default","sleep"; pinctrl-0 = <&sdc1_pins_a>; pinctrl-1 = <&sdc1_pins_b>; max-frequency = <50000000>; bus-width = <4>; /*broken-cd;*/ /*cd-inverted*/ /*cd-gpios = <&pio PG 6 6 1 2 0>;*/ /* vmmc-supply = <®_3p3v>;*/ /* vqmc-supply = <®_3p3v>;*/ /* vdmc-supply = <®_3p3v>;*/ /*vmmc = "vcc-card";*/ /*vqmc = "";*/ /*vdmc = "";*/ cap-sd-highspeed; no-mmc; /*sd-uhs-sdr50;*/ /*sd-uhs-ddr50;*/ /*sd-uhs-sdr104;*/ /*cap-sdio-irq;*/ keep-power-in-suspend; /*ignore-pm-notify;*/ /*sunxi-power-save-mode;*/ /*sunxi-dly-400k = <1 0 0 0 0>; */ /*sunxi-dly-26M = <1 0 0 0 0>;*/ /*sunxi-dly-52M = <1 0 0 0 0>;*/ sunxi-dly-52M-ddr4 = <1 0 0 0 2>; /*sunxi-dly-52M-ddr8 = <1 0 0 0 0>;*/ sunxi-dly-104M = <1 0 0 0 1>; /*sunxi-dly-208M = <1 1 0 0 0>;*/ sunxi-dly-208M = <1 0 0 0 1>; /*sunxi-dly-104M-ddr = <1 0 0 0 0>;*/ /*sunxi-dly-208M-ddr = <1 0 0 0 0>;*/ status = "okay"; }; tpadc: tpadc@2009c00 { compatible = "allwinner,tp_key"; reg = <0x0 0x02009c00 0x0 0x400>; interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_TPADC>, <&ccu CLK_BUS_TPADC>; clock-names = "mod", "bus"; clock-frequency = <1000000>; resets = <&ccu RST_BUS_TPADC>; status = "disabled"; }; rtp:rtp@2009c00 { compatible = "allwinner,sun8i-ts"; reg = <0x0 0x02009c00 0x0 0x400>; clocks = <&ccu CLK_TPADC>, <&ccu CLK_BUS_TPADC>; clock-names = "mod", "bus"; clock-frequency = <1000000>; resets = <&ccu RST_BUS_TPADC>; interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; }; spi0: spi@4025000 { #address-cells = <1>; #size-cells = <0>; compatible = "allwinner,sun8i-spi"; device_type = "spi0"; reg = <0x0 0x04025000 0x0 0x1000>; interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_PLL_PERIPH0>, <&ccu CLK_SPI0>, <&ccu CLK_BUS_SPI0>; clock-names = "pll", "mod", "bus"; resets = <&ccu RST_BUS_SPI0>; clock-frequency = <100000000>; spi0_cs_number = <1>; spi0_cs_bitmap = <1>; dmas = <&dma 22>, <&dma 22>; dma-names = "tx", "rx"; status = "disabled"; }; spi1: spi@4026000 { #address-cells = <1>; #size-cells = <0>; compatible = "allwinner,sun8i-spi"; device_type = "spi1"; reg = <0x0 0x04026000 0x0 0x1000>; interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_PLL_PERIPH0>, <&ccu CLK_SPI1>, <&ccu CLK_BUS_SPI1>; clock-names = "pll", "mod", "bus"; resets = <&ccu RST_BUS_SPI1>; clock-frequency = <100000000>; spi1_cs_number = <1>; spi1_cs_bitmap = <1>; dmas = <&dma 23>, <&dma 23>; dma-names = "tx", "rx"; status = "disabled"; }; ve: ve@1c0e000 { compatible = "allwinner,sunxi-cedar-ve"; reg = <0x0 0x01c0e000 0x0 0x1000>, <0x0 0x03000000 0x0 0x10>, <0x0 0x03001000 0x0 0x1000>; interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_VE>, <&ccu CLK_VE>, <&ccu CLK_MBUS_VE>; clock-names = "bus_ve", "ve", "mbus_ve"; resets = <&ccu RST_BUS_VE>; power-domains = <&pd R528_PD_VE>; iommus = <&mmu_aw 0 1>; status = "okay"; }; twi0: twi@2502000{ #address-cells = <1>; #size-cells = <0>; compatible = "allwinner,sun8i-twi"; device_type = "twi0"; reg = <0x0 0x02502000 0x0 0x400>; interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_I2C0>; resets = <&ccu RST_BUS_I2C0>; clock-names = "bus"; clock-frequency = <400000>; status = "disabled"; }; twi1: twi@2502400{ #address-cells = <1>; #size-cells = <0>; compatible = "allwinner,sun8i-twi"; device_type = "twi1"; reg = <0x0 0x02502400 0x0 0x400>; interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_I2C1>; resets = <&ccu RST_BUS_I2C1>; clock-names = "bus"; clock-frequency = <200000>; status = "disabled"; }; twi2: twi@2502800{ #address-cells = <1>; #size-cells = <0>; compatible = "allwinner,sun8i-twi"; device_type = "twi2"; reg = <0x0 0x02502800 0x0 0x400>; interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_I2C2>; resets = <&ccu RST_BUS_I2C2>; clock-names = "bus"; clock-frequency = <100000>; status = "disabled"; }; twi3: twi@2502c00{ #address-cells = <1>; #size-cells = <0>; compatible = "allwinner,sun8i-twi"; device_type = "twi3"; reg = <0x0 0x02502c00 0x0 0x400>; interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_I2C3>; resets = <&ccu RST_BUS_I2C3>; clock-names = "bus"; clock-frequency = <100000>; status = "disabled"; }; ledc: ledc@2008000 { #address-cells = <1>; #size-cells = <0>; compatible = "allwinner,sunxi-leds"; reg = <0x0 0x02008000 0x0 0x400>; interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "ledcirq"; clocks = <&ccu CLK_LEDC>, <&ccu CLK_BUS_LEDC>; clock-names = "clk_ledc", "clk_cpuapb"; dmas = <&dma 42>, <&dma 42>; dma-names = "rx", "tx"; resets = <&ccu RST_BUS_LEDC>; reset-names = "ledc_reset"; status = "disable"; }; pwm: pwm@2000c00 { #pwm-cells = <0x3>; compatible = "allwinner,sunxi-pwm"; reg = <0x0 0x02000c00 0x0 0x400>; clocks = <&ccu CLK_BUS_PWM>; resets = <&ccu RST_BUS_PWM>; pwm-number = <8>; pwm-base = <0x0>; sunxi-pwms = <&pwm0>, <&pwm1>, <&pwm2>, <&pwm3>, <&pwm4>, <&pwm5>, <&pwm6>, <&pwm7>; }; pwm0: pwm0@2000c10 { compatible = "allwinner,sunxi-pwm0"; pinctrl-names = "active", "sleep"; reg = <0x0 0x02000c10 0x0 0x4>; reg_base = <0x02000c00>; }; pwm1: pwm1@2000c11 { compatible = "allwinner,sunxi-pwm1"; pinctrl-names = "active", "sleep"; reg = <0x0 0x02000c11 0x0 0x4>; reg_base = <0x02000c00>; }; pwm2: pwm2@2000c12 { compatible = "allwinner,sunxi-pwm2"; pinctrl-names = "active", "sleep"; reg = <0x0 0x02000c12 0x0 0x4>; reg_base = <0x02000c00>; }; pwm3: pwm3@2000c13 { compatible = "allwinner,sunxi-pwm3"; pinctrl-names = "active", "sleep"; reg = <0x0 0x02000c13 0x0 0x4>; reg_base = <0x02000c00>; }; pwm4: pwm4@2000c14 { compatible = "allwinner,sunxi-pwm4"; pinctrl-names = "active", "sleep"; reg = <0x0 0x02000c14 0x0 0x4>; reg_base = <0x02000c00>; }; pwm5: pwm5@2000c15 { compatible = "allwinner,sunxi-pwm5"; pinctrl-names = "active", "sleep"; reg = <0x0 0x02000c15 0x0 0x4>; reg_base = <0x02000c00>; }; pwm6: pwm6@2000c16 { compatible = "allwinner,sunxi-pwm6"; pinctrl-names = "active", "sleep"; reg = <0x0 0x02000c16 0x0 0x4>; reg_base = <0x02000c00>; }; pwm7: pwm7@2000c17 { compatible = "allwinner,sunxi-pwm7"; pinctrl-names = "active", "sleep"; reg = <0x0 0x02000c17 0x0 0x4>; reg_base = <0x02000c00>; }; lcd_fb0: lcd_fb0@0 { compatible = "allwinner,sunxi-lcd_fb0"; pinctrl-names = "active","sleep"; status = "okay"; }; keyboard0: keyboard@2009800 { compatible = "allwinner,keyboard_1350mv"; reg = <0x0 0x02009800 0x0 0x400>; interrupts = <GIC_SPI 61 IRQ_TYPE_EDGE_RISING>; clocks = <&ccu CLK_BUS_LRADC>; clock-names = "mclk"; resets = <&ccu RST_BUS_LRADC>; key_cnt = <5>; key0 = <210 115>; key1 = <410 114>; key2 = <590 139>; key3 = <750 28>; key4 = <880 172>; wakeup-source; status = "okay"; }; sid@3006000 { compatible = "allwinner,sun8iw20p1-sid", "allwinner,sunxi-sid"; reg = <0x0 0x03006000 0 0x1000>; #address-cells = <1>; #size-cells = <1>; secure_status { reg = <0x0 0>; offset = <0xa0>; size = <0x4>; }; chipid { reg = <0x0 0>; offset = <0x200>; size = <0x10>; }; rotpk { reg = <0x0 0>; offset = <0x140>; size = <0x4>; }; speedbin_efuse: speedbin@00 { reg = <0x00 2>; }; cpubin_efuse: cpubin@28 { reg = <0x28 2>; }; ths_calib: calib@14 { reg = <0x14 8>; }; }; gpadc: gpadc@2009000 { compatible = "allwinner,sunxi-gpadc"; reg = <0x0 0x02009000 0x0 0x400>; interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_GPADC>; clock-names = "bus"; resets = <&ccu RST_BUS_GPADC>; status = "okay"; }; vind0: vind@5800800 { compatible = "allwinner,sunxi-vin-media", "simple-bus"; #address-cells = <2>; #size-cells = <2>; ranges; device_id = <0>; csi_top = <336000000>; csi_isp = <327000000>; reg = <0x0 0x05800800 0x0 0x200>, <0x0 0x05800000 0x0 0x800>; clocks = <&ccu CLK_CSI_TOP>, <&ccu CLK_PLL_VIDEO1_2X>, <&ccu CLK_CSI0_MCLK>, <&dcxo24M>, <&ccu CLK_PLL_VIDEO1>, <&ccu CLK_BUS_CSI>, <&ccu CLK_MBUS_CSI>; clock-names = "csi_top", "csi_top_src", "csi_mclk0", "csi_mclk0_24m", "csi_mclk0_pll", "csi_bus", "csi_mbus"; resets = <&ccu RST_BUS_CSI>; reset-names = "csi_ret"; pinctrl-names = "mclk0-default", "mclk0-sleep"; pinctrl-0 = <&csi_mclk0_pins_a>; pinctrl-1 = <&csi_mclk0_pins_b>; status = "okay"; csi0: csi@5801000{ compatible = "allwinner,sunxi-csi"; reg = <0x0 0x05801000 0x0 0x1000>; interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default","sleep"; pinctrl-0 = <&csi0_pins_a>; pinctrl-1 = <&csi0_pins_b>; device_id = <0>; iommus = <&mmu_aw 1 1>; status = "okay"; }; isp0: isp@5809410 { compatible = "allwinner,sunxi-isp"; reg = <0x0 0x05809410 0x0 0x10>; device_id = <0xfe>; status = "okay"; }; isp1: isp@5809420 { compatible = "allwinner,sunxi-isp"; reg = <0x0 0x05809420 0x0 0x10>; device_id = <0xff>; status = "okay"; }; scaler0: scaler@5809430 { compatible = "allwinner,sunxi-scaler"; reg = <0x0 0x05809430 0x0 0x10>; device_id = <0xfe>; status = "okay"; }; scaler1: scaler@5809440 { compatible = "allwinner,sunxi-scaler"; reg = <0x0 0x05809440 0x0 0x10>; device_id = <0xff>; status = "okay"; }; actuator0: actuator@5809450 { compatible = "allwinner,sunxi-actuator"; device_type = "actuator0"; reg = <0x0 0x05809450 0x0 0x10>; actuator0_name = "ad5820_act"; actuator0_slave = <0x18>; actuator0_af_pwdn = <>; actuator0_afvdd = "afvcc-csi"; actuator0_afvdd_vol = <2800000>; status = "disabled"; }; flash0: flash@5809460 { device_type = "flash0"; compatible = "allwinner,sunxi-flash"; reg = <0x0 0x05809460 0x0 0x10>; flash0_type = <2>; flash0_en = <>; flash0_mode = <>; flash0_flvdd = ""; flash0_flvdd_vol = <>; device_id = <0>; status = "disabled"; }; sensor0: sensor@5809470 { reg = <0x0 0x05809470 0x0 0x10>; device_type = "sensor0"; compatible = "allwinner,sunxi-sensor"; sensor0_mname = "ov5640"; sensor0_twi_cci_id = <2>; sensor0_twi_addr = <0x78>; sensor0_mclk_id = <0>; sensor0_pos = "rear"; sensor0_isp_used = <0>; sensor0_fmt = <0>; sensor0_stby_mode = <0>; sensor0_vflip = <0>; sensor0_hflip = <0>; sensor0_iovdd-supply = <>; sensor0_iovdd_vol = <>; sensor0_avdd-supply = <>; sensor0_avdd_vol = <>; sensor0_dvdd-supply = <>; sensor0_dvdd_vol = <>; sensor0_power_en = <>; sensor0_reset = <&pio PE 9 GPIO_ACTIVE_LOW>; sensor0_pwdn = <&pio PE 8 GPIO_ACTIVE_LOW>; sensor0_sm_vs = <>; flash_handle = <&flash0>; act_handle = <&actuator0>; device_id = <0>; status = "okay"; }; sensor1: sensor@5809480 { reg = <0x0 0x05809480 0x0 0x10>; device_type = "sensor1"; compatible = "allwinner,sunxi-sensor"; sensor1_mname = "ov5647"; sensor1_twi_cci_id = <3>; sensor1_twi_addr = <0x6c>; sensor1_mclk_id = <1>; sensor1_pos = "front"; sensor1_isp_used = <0>; sensor1_fmt = <0>; sensor1_stby_mode = <0>; sensor1_vflip = <0>; sensor1_hflip = <0>; sensor1_iovdd-supply = <>; sensor1_iovdd_vol = <>; sensor1_avdd-supply = <>; sensor1_avdd_vol = <>; sensor1_dvdd-supply = <>; sensor1_dvdd_vol = <>; sensor1_power_en = <>; sensor1_reset = <&pio PE 7 GPIO_ACTIVE_LOW>; sensor1_pwdn = <&pio PE 6 GPIO_ACTIVE_LOW>; sensor1_sm_vs = <>; flash_handle = <>; act_handle = <>; device_id = <1>; status = "okay"; }; vinc0: vinc@5809000 { compatible = "allwinner,sunxi-vin-core"; device_type = "vinc0"; reg = <0x0 0x05809000 0x0 0x200>; interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; vinc0_csi_sel = <0>; vinc0_mipi_sel = <0xff>; vinc0_isp_sel = <0>; vinc0_tdm_rx_sel = <0xff>; vinc0_rear_sensor_sel = <0>; vinc0_front_sensor_sel = <0>; vinc0_sensor_list = <0>; device_id = <0>; iommus = <&mmu_aw 1 1>; status = "okay"; }; vinc1: vinc@5809200 { device_type = "vinc1"; compatible = "allwinner,sunxi-vin-core"; reg = <0x0 0x05809200 0x0 0x200>; interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; vinc1_csi_sel = <0>; vinc1_mipi_sel = <0xff>; vinc1_isp_sel = <1>; vinc1_tdm_rx_sel = <0xff>; vinc1_rear_sensor_sel = <0>; vinc1_front_sensor_sel = <0>; vinc1_sensor_list = <0>; device_id = <1>; iommus = <&mmu_aw 1 1>; status = "okay"; }; }; s_cir0: s_cir@7040000 { compatible = "allwinner,s_cir"; reg = <0x0 0x07040000 0x0 0x400>; interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>; clocks = <&r_ccu CLK_R_APB0_BUS_IRRX>, <&dcxo24M>, <&r_ccu CLK_R_APB0_IRRX>; clock-names = "bus", "pclk", "mclk"; resets = <&r_ccu RST_R_APB0_BUS_IRRX>; status = "disabled"; }; ir1: ir@2003000 { compatible = "allwinner,irtx"; reg = <0x0 0x02003000 0x0 0x400>; interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_IR_TX>, <&dcxo24M>, <&ccu CLK_IR_TX>; clock-names = "bus", "pclk", "mclk"; resets = <&ccu RST_BUS_IR_TX>; status = "disabled"; }; di: deinterlace@5400000 { compatible = "allwinner,sunxi-deinterlace"; reg = <0x0 0x05400000 0x0 0x0000ffff>; interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_DI>, <&ccu CLK_BUS_DI>, <&ccu CLK_PLL_PERIPH0_2X>; clock-names = "clk_di", "pll_periph", "clk_bus_di"; resets = <&ccu RST_BUS_DI>; reset-names = "rst_bus_di"; assigned-clocks = <&ccu CLK_DI>; assigned-clock-parents = <&ccu CLK_PLL_PERIPH0_2X>; assigned-clock-rates = <300000000>; iommus = <&mmu_aw 4 1>; status = "okay"; }; g2d: g2d@5410000 { compatible = "allwinner,sunxi-g2d"; reg = <0x0 0x05410000 0x0 0x3ffff>; interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_G2D>, <&ccu CLK_G2D>, <&ccu CLK_MBUS_G2D>; clock-names = "bus", "g2d", "mbus_g2d"; resets = <&ccu RST_BUS_G2D>; iommus = <&mmu_aw 3 1>; status = "okay"; }; disp: disp@5000000 { compatible = "allwinner,sunxi-disp"; reg = <0x0 0x05000000 0x0 0x3fffff>, /* de0 */ <0x0 0x05460000 0x0 0xfff>, /*display_if_top*/ <0x0 0x05461000 0x0 0xfff>, /* tcon-lcd0 */ <0x0 0x05470000 0x0 0xfff>, /* tcon-tv */ <0x0 0x05450000 0x0 0x1fff>; /* dsi0*/ interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,/*tcon-lcd0*/ <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,/*tcon-tv */ <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;/*dsi*/ clocks = <&ccu CLK_DE0>, <&ccu CLK_DE0>, <&ccu CLK_BUS_DE0>, <&ccu CLK_BUS_DE0>, <&ccu CLK_BUS_DPSS_TOP0>, <&ccu CLK_BUS_DPSS_TOP0>, <&ccu CLK_MIPI_DSI>, <&ccu CLK_BUS_MIPI_DSI>, <&ccu CLK_TCON_LCD0>, <&ccu CLK_TCON_TV>, <&ccu CLK_BUS_TCON_LCD0>, <&ccu CLK_BUS_TCON_TV>, <&ccu CLK_MIPI_DSI>, <&ccu CLK_BUS_MIPI_DSI>; clock-names = "clk_de0", "clk_de1", "clk_bus_de0", "clk_bus_de1", "clk_bus_dpss_top0", "clk_bus_dpss_top1", "clk_mipi_dsi0", "clk_bus_mipi_dsi0", "clk_tcon0", "clk_tcon1",/*tcon-tv actually*/ "clk_bus_tcon0", "clk_bus_tcon1",/*tcon-tv actually*/ "clk_mipi_dsi0", "clk_bus_mipi_dsi0"; resets = <&ccu RST_BUS_DE0>, <&ccu RST_BUS_DE0>, <&ccu RST_BUS_DPSS_TOP0>, <&ccu RST_BUS_DPSS_TOP0>, <&ccu RST_BUS_MIPI_DSI>, <&ccu RST_BUS_TCON_LCD0>, <&ccu RST_BUS_TCON_TV>, <&ccu RST_BUS_LVDS0>; reset-names = "rst_bus_de0", "rst_bus_de1", "rst_bus_dpss_top0", "rst_bus_dpss_top1", "rst_bus_mipi_dsi0", "rst_bus_tcon0", "rst_bus_tcon1", "rst_bus_lvds0"; assigned-clocks = <&ccu CLK_DE0>, <&ccu CLK_MIPI_DSI>, <&ccu CLK_TCON_LCD0>, <&ccu CLK_TCON_TV>; assigned-clock-parents = <&ccu CLK_PLL_PERIPH0_2X>, <&ccu CLK_PLL_PERIPH0>, <&ccu CLK_PLL_VIDEO0_4X>, <&ccu CLK_PLL_VIDEO1_4X>; assigned-clock-rates = <300000000>, <150000000>, <0>, <0>; boot_disp = <0>; boot_disp1 = <0>; boot_disp2 = <0>; fb_base = <0>; iommus = <&mmu_aw 2 0>; status = "okay"; }; lcd0: lcd0@5461000 { compatible = "allwinner,sunxi-lcd0"; reg = <0x0 0x05461000 0x0 0xfff>; pinctrl-names = "active","sleep"; status = "okay"; }; tv0: tv0@5600000 { compatible = "allwinner,sunxi-tv"; reg = <0x0 0x05600000 0x0 0x3fff>, <0x0 0x05604000 0x0 0x3fff>; clocks = <&ccu CLK_BUS_TVE_TOP>, <&ccu CLK_TVE>, <&ccu CLK_BUS_TVE>; clock-names = "clk_bus_tve_top", "clk_tve", "clk_bus_tve"; resets = <&ccu RST_BUS_TVE_TOP>, <&ccu RST_BUS_TVE>; reset-names = "rst_bus_tve_top", "rst_bus_tve"; device_type = "tv0"; pinctrl-names = "active","sleep"; status = "okay"; }; hwspinlock: hwspinlock@0x3005000 { compatible = "allwinner,sunxi-hwspinlock"; reg = <0x0 0x3005000 0x0 0x1000>; #hwlock-cells = <1>; clocks = <&ccu CLK_BUS_SPINLOCK>; clock-names = "clk_hwspinlock_bus"; resets = <&ccu RST_BUS_SPINLOCK>; reset-names = "rst"; num-locks = <32>; status = "disabled"; }; /* old msgbox in dts msgbox: msgbox@3003000 { compatible = "sunxi,msgbox-amp"; reg = <0x0 0x03003000 0x0 0x1000>, <0x0 0x01701000 0x0 0x1000>, <0x0 0x0601f000 0x0 0x1000>; interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_MSGBOX0>; rpmsg_id = "sunxi,dsp-msgbox","sunxi,dsp-power-msgbox"; resets = <&ccu RST_BUS_MSGBOX0>; reset-names = "rst"; msgbox_amp_counts = <3>; msgbox_amp_local = <0>; rpmsg_amp_remote-0 = <1>; rpmsg_read_channel-0 = <1>; rpmsg_write_channel-0 = <1>; rpmsg_amp_remote-1 = <1>; rpmsg_read_channel-1 = <0>; rpmsg_write_channel-1 = <0>; }; */ msgbox: msgbox@3003000 { compatible = "allwinner,sunxi-msgbox"; #mbox-cells = <1>; reg = <0x0 0x03003000 0x0 0x1000>, <0x0 0x01701000 0x0 0x1000>, <0x0 0x0601f000 0x0 0x1000>; interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_MSGBOX0>; resets = <&ccu RST_BUS_MSGBOX0>; reset-names = "rst"; local_id = <0>; }; hdmi: hdmi@5500000 { compatible = "allwinner,sunxi-hdmi"; reg = <0x0 0x05500000 0x0 0xfffff>; interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_24M>, <&ccu CLK_HDMI_CEC>, <&ccu CLK_TCON_TV>; clock-names = "clk_bus_hdmi", "clk_ddc", "clk_cec", "clk_tcon_tv"; resets = <&ccu RST_BUS_HDMI_SUB>, <&ccu RST_BUS_HDMI_MAIN>; reset-names = "rst_bus_sub", "rst_bus_main"; assigned-clocks = <&ccu CLK_HDMI_CEC>; assigned-clock-parents = <&ccu CLK_HDMI_CEC_32K>; assigned-clock-rates = <0>; status = "okay"; }; usbc0:usbc0@0 { device_type = "usbc0"; compatible = "allwinner,sunxi-otg-manager"; usb_port_type = <2>; usb_detect_type = <1>; usb_id_gpio; usb_det_vbus_gpio; usb_regulator_io = "nocare"; usb_wakeup_suspend = <0>; usb_luns = <3>; usb_serial_unique = <0>; usb_serial_number = "20080411"; rndis_wceis = <1>; status = "okay"; }; udc:udc-controller@0x04100000 { compatible = "allwinner,sunxi-udc"; reg = <0x0 0x04100000 0x0 0x1000>, /*udc base*/ <0x0 0x00000000 0x0 0x100>; /*sram base*/ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_OTG>; clock-names = "bus_otg"; resets = <&ccu RST_BUS_OTG>, <&ccu RST_USB_PHY0>; reset-names = "otg", "phy"; status = "okay"; }; ehci0:ehci0-controller@0x04101000 { compatible = "allwinner,sunxi-ehci0"; reg = <0x0 0x04101000 0x0 0xFFF>, /*hci0 base*/ <0x0 0x00000000 0x0 0x100>, /*sram base*/ <0x0 0x04100000 0x0 0x1000>; /*otg base*/ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_EHCI0>; clock-names = "bus_hci"; resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_USB_PHY0>; reset-names = "hci", "phy"; hci_ctrl_no = <0>; status = "okay"; }; ohci0:ohci0-controller@0x04101400 { compatible = "allwinner,sunxi-ohci0"; reg = <0x0 0x04101400 0x0 0xFFF>, /*hci0 base*/ <0x0 0x00000000 0x0 0x100>, /*sram base*/ <0x0 0x04100000 0x0 0x1000>; /*otg base*/ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_OHCI0>, <&ccu CLK_USB_OHCI0>; clock-names = "bus_hci", "ohci"; resets = <&ccu RST_BUS_OHCI0>, <&ccu RST_USB_PHY0>; reset-names = "hci", "phy"; hci_ctrl_no = <0>; status = "okay"; }; usbc1:usbc1@0 { device_type = "usbc1"; usb_regulator_io = "nocare"; usb_wakeup_suspend = <0>; status = "disable"; }; ehci1:ehci1-controller@0x04200000 { compatible = "allwinner,sunxi-ehci1"; reg = <0x0 0x04200000 0x0 0xFFF>, /*ehci1 base*/ <0x0 0x00000000 0x0 0x100>, /*sram base*/ <0x0 0x04100000 0x0 0x1000>; /*otg base*/ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_EHCI1>; clock-names = "bus_hci"; resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_USB_PHY1>; reset-names = "hci", "phy"; hci_ctrl_no = <1>; status = "disable"; }; ohci1:ohci1-controller@0x04200400 { compatible = "allwinner,sunxi-ohci1"; reg = <0x0 0x04200400 0x0 0xFFF>, /*ohci1 base*/ <0x0 0x00000000 0x0 0x100>, /*sram base*/ <0x0 0x04100000 0x0 0x1000>; /*otg base*/ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_OHCI1>, <&ccu CLK_USB_OHCI1>; clock-names = "bus_hci", "ohci"; resets = <&ccu RST_BUS_OHCI1>, <&ccu RST_USB_PHY1>; reset-names = "hci", "phy"; hci_ctrl_no = <1>; status = "disable"; }; /* codec addr: 0x02030000, the others is invalid to avoid build warining */ codec:codec@2030000 { #sound-dai-cells = <0>; compatible = "allwinner,sunxi-internal-codec"; reg = <0x0 0x02030000 0x0 0x34c>; clocks = <&ccu CLK_PLL_AUDIO0>, <&ccu CLK_PLL_AUDIO1_DIV5>, <&ccu CLK_AUDIO_DAC>, <&ccu CLK_AUDIO_ADC>, <&ccu CLK_BUS_AUDIO_CODEC>; clock-names = "pll_audio0", "pll_audio1_div5", "audio_clk_dac", "audio_clk_adc", "audio_clk_bus"; resets = <&ccu RST_BUS_AUDIO_CODEC>; rx_sync_en = <0x00>; device_type = "codec"; status = "okay"; }; dummy_cpudai:dummy_cpudai@203034c { compatible = "allwinner,sunxi-dummy-cpudai"; reg = <0x0 0x0203034c 0x0 0x4>; tx_fifo_size = <128>; rx_fifo_size = <256>; dac_txdata = <0x02030020>; adc_txdata = <0x02030040>; playback_cma = <128>; capture_cma = <256>; device_type = "cpudai"; dmas = <&dma 7>, <&dma 7>; dma-names = "tx", "rx"; status = "okay"; }; sndcodec:sound@2030340 { compatible = "allwinner,sunxi-codec-machine"; reg = <0x0 0x02030340 0x0 0x4>; interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; sunxi,audio-codec = <&codec>; sunxi,cpudai-controller = <&dummy_cpudai>; device_type = "sndcodec"; status = "okay"; }; sunxi_rpaf_dsp0:rpaf-dsp@203034c { compatible = "allwinner,rpaf-dsp0"; device_type = "sunxi_rpaf_dsp0"; dsp_id = <0x0>; status = "okay"; }; /* dmic addr: 0x02031000, the others is invalid to avoid build warining */ dmic:dmic@2031000{ #sound-dai-cells = <0>; compatible = "allwinner,sunxi-dmic"; reg = <0x0 0x02031000 0x0 0x50>; clocks = <&ccu CLK_PLL_AUDIO0>, /* 98.304M / 90.3168M */ <&ccu CLK_DMIC>, <&ccu CLK_BUS_DMIC>; clock-names = "pll_audio", "dmic", "dmic_bus"; resets = <&ccu RST_BUS_DMIC>; dmas = <&dma 8>; dma-names = "rx"; interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; clk_parent = <0x1>; capture_cma = <256>; data_vol = <0xB0>; rx_chmap = <0x76543210>; rx_sync_en = <0x00>; device_type = "dmic"; status = "disabled"; }; dmic_codec:sound@2031050{ #sound-dai-cells = <0>; compatible = "dmic-codec"; reg = <0x0 0x02031050 0x0 0x4>; num-channels = <8>; }; sounddmic:sounddmic@2031060 { reg = <0x0 0x02031060 0x0 0x4>; compatible = "sunxi,simple-audio-card"; simple-audio-card,name = "snddmic"; simple-audio-card,capture_only; status = "disabled"; /* simple-audio-card,format = "i2s"; */ simple-audio-card,cpu { sound-dai = <&dmic>; }; simple-audio-card,codec { sound-dai = <&dmic_codec>; }; }; /* daudio0 addr: 0x02032000, the others is invalid to avoid build warining */ daudio0:daudio@2032000 { #sound-dai-cells = <0>; compatible = "allwinner,sunxi-daudio"; reg = <0x0 0x02032000 0x0 0xa0>; clocks = <&ccu CLK_PLL_AUDIO0>, /* 98.304M / 90.3168M */ <&ccu CLK_I2S0>, <&ccu CLK_BUS_I2S0>; clock-names = "pll_audio", "i2s0", "i2s0_bus"; resets = <&ccu RST_BUS_I2S0>; dmas = <&dma 3>, <&dma 3>; dma-names = "tx", "rx"; interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; pinctrl_used = <0x01>; sign_extend = <0x00>; tx_data_mode = <0x00>; rx_data_mode = <0x00>; msb_lsb_first = <0x00>; pcm_lrck_period = <0x80>; slot_width_select = <0x20>; frametype = <0x00>; tdm_config = <0x01>; tdm_num = <0x00>; mclk_div = <0x00>; clk_parent = <0x00>; capture_cma = <128>; playback_cma = <128>; tx_num = <4>; tx_chmap1 = <0x76543210>; tx_chmap0 = <0xFEDCBA98>; rx_num = <4>; rx_chmap3 = <0x03020100>; rx_chmap2 = <0x07060504>; rx_chmap1 = <0x0B0A0908>; rx_chmap0 = <0x0F0E0D0C>; asrc_function_en = <0x00>; rx_sync_en = <0x00>; device_type = "daudio0"; status = "disabled"; }; sounddaudio0: sounddaudio0@20320a0 { reg = <0x0 0x020320a0 0x0 0x4>; compatible = "sunxi,simple-audio-card"; simple-audio-card,name = "snddaudio0"; simple-audio-card,format = "i2s"; status = "disabled"; /* simple-audio-card,frame-master = <&daudio0_master>; */ /* simple-audio-card,bitclock-master = <&daudio0_master>; */ /* simple-audio-card,bitclock-inversion; */ /* simple-audio-card,frame-inversion; */ simple-audio-card,cpu { sound-dai = <&daudio0>; }; }; /* daudio1 addr: 0x02033000, the others is invalid to avoid build warining */ daudio1:daudio@2033000 { #sound-dai-cells = <0>; compatible = "allwinner,sunxi-daudio"; reg = <0x0 0x02033000 0x0 0xa0>; clocks = <&ccu CLK_PLL_AUDIO0>, /* 98.304M / 90.3168M */ <&ccu CLK_I2S1>, <&ccu CLK_BUS_I2S1>; clock-names = "pll_audio", "i2s1", "i2s1_bus"; resets = <&ccu RST_BUS_I2S1>; dmas = <&dma 4>, <&dma 4>; dma-names = "tx", "rx"; interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; pinctrl_used = <0x01>; sign_extend = <0x00>; tx_data_mode = <0x00>; rx_data_mode = <0x00>; msb_lsb_first = <0x00>; pcm_lrck_period = <0x80>; slot_width_select = <0x20>; frametype = <0x00>; tdm_config = <0x01>; tdm_num = <0x01>; mclk_div = <0x00>; clk_parent = <0x00>; capture_cma = <128>; playback_cma = <128>; tx_num = <4>; tx_chmap1 = <0x76543210>; tx_chmap0 = <0xFEDCBA98>; rx_num = <4>; rx_chmap3 = <0x03020100>; rx_chmap2 = <0x07060504>; rx_chmap1 = <0x0B0A0908>; rx_chmap0 = <0x0F0E0D0C>; asrc_function_en = <0x00>; rx_sync_en = <0x00>; device_type = "daudio1"; status = "disabled"; }; sounddaudio1: sounddaudio1@20330a0 { reg = <0x0 0x020330a0 0x0 0x4>; compatible = "sunxi,simple-audio-card"; simple-audio-card,name = "snddaudio1"; simple-audio-card,format = "i2s"; status = "disabled"; simple-audio-card,cpu { sound-dai = <&daudio1>; }; }; /* daudio2 addr: 0x02034000, the others is invalid to avoid build warining */ daudio2:daudio@2034000 { #sound-dai-cells = <0>; compatible = "allwinner,sunxi-daudio"; reg = <0x0 0x02034000 0x0 0xa0>; clocks = <&ccu CLK_PLL_AUDIO0>, /* 98.304M / 90.3168M */ <&ccu CLK_I2S2>, <&ccu CLK_BUS_I2S2>, <&ccu CLK_PLL_AUDIO0_4X>, <&ccu CLK_I2S2_ASRC>; resets = <&ccu RST_BUS_I2S2>; dmas = <&dma 5>, <&dma 5>; dma-names = "tx", "rx"; interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; pinctrl_used = <0x01>; daudio_type = <0x00>; sign_extend = <0x00>; tx_data_mode = <0x00>; rx_data_mode = <0x00>; msb_lsb_first = <0x00>; pcm_lrck_period = <0x80>; slot_width_select = <0x20>; frametype = <0x00>; tdm_config = <0x01>; tdm_num = <0x02>; mclk_div = <0x01>; clk_parent = <0x00>; capture_cma = <128>; playback_cma = <128>; tx_num = <4>; tx_chmap1 = <0x76543210>; tx_chmap0 = <0xFEDCBA98>; rx_num = <4>; rx_chmap3 = <0x03020100>; rx_chmap2 = <0x07060504>; rx_chmap1 = <0x0B0A0908>; rx_chmap0 = <0x0F0E0D0C>; asrc_function_en = <0x00>; rx_sync_en = <0x00>; device_type = "daudio2"; status = "disabled"; }; sounddaudio2: sounddaudio2@20340a0 { reg = <0x0 0x020340a0 0x0 0x4>; compatible = "sunxi,simple-audio-card"; simple-audio-card,name = "snddaudio2"; simple-audio-card,format = "i2s"; status = "disabled"; simple-audio-card,cpu { sound-dai = <&daudio2>; }; }; hdmiaudio: hdmiaudio@20340a4 { #sound-dai-cells = <0>; reg = <0x0 0x020340a4 0x0 0x4>; compatible = "allwinner,sunxi-hdmiaudio"; status = "disabled"; }; /* spdif addr: 0x02036000, the others is invalid to avoid build warining */ spdif:spdif@2036000 { #sound-dai-cells = <0>; compatible = "allwinner,sunxi-spdif"; reg = <0x0 0x02036000 0x0 0x58>; clocks = <&ccu CLK_PLL_AUDIO0_4X>, /* 90.3168M */ <&ccu CLK_SPDIF_TX>, <&ccu CLK_BUS_SPDIF>, <&ccu CLK_PLL_AUDIO1>, /* 98.304M */ <&ccu CLK_PLL_AUDIO1_DIV5>, <&ccu CLK_PLL_PERIPH0>, <&ccu CLK_SPDIF_RX>; clock-names = "pll_audio0", "spdif", "spdif_bus", "pll_audio1", "pll_audio1_div5", "pll_periph", "spdif_rx"; resets = <&ccu RST_BUS_SPDIF>; dmas = <&dma 2>, <&dma 2>; dma-names = "tx", "rx"; interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; clk_parent = <0x1>; playback_cma = <128>; capture_cma = <128>; rx_sync_en = <0>; device_type = "spdif"; status = "disabled"; }; soundspdif:soundspdif@203605c { reg = <0x0 0x0203605c 0x0 0x4>; compatible = "sunxi,simple-audio-card"; simple-audio-card,name = "sndspdif"; status = "disabled"; /* simple-audio-card,format = "i2s"; */ simple-audio-card,cpu { sound-dai = <&spdif>; }; simple-audio-card,codec { /*snd-soc-dummy*/ }; }; ths: ths@02009400 { compatible = "allwinner,sun8iw20p1-ths"; reg = <0x0 0x02009400 0x0 0x400>; clocks = <&ccu CLK_BUS_THS>; clock-names = "bus"; resets = <&ccu RST_BUS_THS>; nvmem-cells = <&ths_calib>; nvmem-cell-names = "calibration"; #thermal-sensor-cells = <1>; }; tvd: tvd@05c00000 { compatible = "allwinner,sunxi-tvd"; reg = <0x0 0x05c00000 0x0 0x00010000>;/*tvd_top*/ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_TVD_TOP>, <&ccu CLK_MBUS_TVIN>; clock-names = "clk_bus_tvd_top", "clk_mbus_tvd"; resets = <&ccu RST_BUS_TVD_TOP>; reset-names = "rst_bus_tvd_top"; tvd-number = <1>; tvds = <&tvd0>; status = "okay"; }; tvd0: tvd0@05c01000 { compatible = "allwinner,sunxi-tvd0"; reg = <0x0 0x05c01000 0x0 0x00010000>; interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_TVD>, <&ccu CLK_BUS_TVD>; clock-names = "clk_tvd0","clk_bus_tvd0"; resets = <&ccu RST_BUS_TVD>; reset-names = "rst_bus_tvd0"; assigned-clocks = <&ccu CLK_TVD>; assigned-clock-parents = <&ccu CLK_PLL_VIDEO1>; tvd_used = <1>; tvd_if = <0>; status = "okay"; }; }; }; -
RT内核没研究过，不过可以先试试普通内核能不能启动手动打入rt补丁看看
-
@awwwwa 谢谢你，我试了下，又卡在另一个地方，还在扒资料
。[247]HELLO! BOOT0 is starting! [250]BOOT0 commit : adaf1174cc [253]set pll start [259]periph0 has been enabled [262]set pll end [264][pmu]: bus read error [266]board init ok [268]ZQ value = 0x2f [270]get_pmu_exist() = -1 [273]ddr_efuse_type: 0xa [275]trefi:7.8ms [278][AUTO DEBUG] single rank and full DQ! [282]ddr_efuse_type: 0xa [285]trefi:7.8ms [287][AUTO DEBUG] rank 0 row = 13 [290][AUTO DEBUG] rank 0 bank = 8 [294][AUTO DEBUG] rank 0 page size = 2 KB [298]DRAM BOOT DRIVE INFO: V0.33 [301]DRAM CLK = 936 MHz [303]DRAM Type = 3 (2:DDR2,3:DDR3) [307]DRAMC read ODT off. [309]DRAM ODT value: 0x42. [312]ddr_efuse_type: 0xa [315]DRAM SIZE =128 M [317]dram_tpr4:0x0 [319]PLL_DDR_CTRL_REG:0xf8004d00 [322]DRAM_CLK_REG:0xc0000000 [325][TIMING DEBUG] MR2= 0x20 [333]DRAM simple test OK. [335]rtc standby flag is 0x0, super standby flag is 0x0 [341]dram size =128 [344]card no is 0 [345]sdcard 0 line count 4 [348][mmc]: mmc driver ver 2021-05-21 14:47 [357][mmc]: Wrong media type 0x0 [360][mmc]: ***Try SD card 0*** [379][mmc]: HSSDR52/SDR25 4 bit [381][mmc]: 50000000 Hz [384][mmc]: 30436 MB [386][mmc]: ***SD/MMC 0 init OK!!!*** [483]Loading boot-pkg Succeed(index=0). [486]Entry_name = u-boot [493]Entry_name = optee [497]Entry_name = dtb [500]mmc not para [502]Jump to second Boot. M/TC: OP-TEE version: e9372c9c-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #2 Sat Mar 19 11:09:45 UTC 2022 arm U-Boot 2018.05 (Nov 02 2023 - 16:17:13 +0800) Allwinner Technology [00.555]CPU: Allwinner Family [00.558]Model: sun8iw20 [00.560]DRAM: 128 MiB [00.563]Relocation Offset is: 04ebc000 [00.589]secure enable bit: 0 E/TC:0 tee_read_fdt:433 fine node /firmware/optee failed with FDT_ERR_NOTFOUND [00.601]smc_tee_inform_fdt failed with: -65536[00.605]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz [00.611]gic: sec monitor mode [00.614]flash init start [00.616]workmode = 0,storage type = 1 [00.620][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00 [00.625][mmc]: get sdc_type fail and use default host:tm1. [00.631][mmc]: can't find node "mmc0",will add new node [00.636][mmc]: fdt err returned <no error> [00.640][mmc]: Using default timing para [00.643][mmc]: SUNXI SDMMC Controller Version:0x50310 [00.670][mmc]: card_caps:0x3000000a [00.673][mmc]: host_caps:0x3000003f [00.681]sunxi flash init ok [00.684]line:703 init_clocks [00.687]drv_disp_init request pwm success, pwm7:pwm7:0x2000c00. fdt get node offset faill: hdmi [00.703]unable to map hdmi registers [00.706]drv_disp_init finish [00.721]Loading Environment from SUNXI_FLASH... OK [00.740]boot_gui_init:start [00.743]set disp.dev2_output_type fail. using defval=0 [00.750]boot_gui_init:finish partno erro : can't find partition bootloader 54 bytes read in 1 ms (52.7 KiB/s) [00.764]bmp_name=bootlogo.bmp size 38454 38454 bytes read in 4 ms (9.2 MiB/s) [00.796]Item0 (Map) magic is bad [00.798]the secure storage item0 copy0 magic is bad [00.818]Item0 (Map) magic is bad [00.821]the secure storage item0 copy1 magic is bad [00.825]Item0 (Map) magic is bad [00.828]out of usb burn from boot: not need burn key List file under ULI/factory ** Unrecognized filesystem type ** root_partition is rootfs set root to /dev/mmcblk0p5 [00.847]update part info [00.850]update bootcmd [00.853]change working_fdt 0x43e7be70 to 0x43e5be70 disable nand error: FDT_ERR_BADPATH [00.874]update dts Hit any key to stop autoboot: 1 FDT ERROR:get muxsel err returned FDT_ERR_INTERNAL sunxi_pwm_pin_set_state, fdt_set_all_pin, ret=-1 [00.939]LCD open finish 0 [02.627]no vendor_boot partition is found Android's image name: sun8i_arm [02.645]Starting kernel ... [02.648][mmc]: MMC Device 2 not found [02.651][mmc]: mmc 2 not find, so not exit [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.61 (ubuntu@win) (arm-linux-gnueabi-gcc (Linaro GCC 5.3-2016.05) 5.3.1 20160412, GNU ld (Linaro_Binutils-2016.05) 2.25.0 Linaro 2016_02) #3 SMP PREEMPT Thu Nov 2 16:16:30 CST 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: sun8iw20 [ 0.000000] printk: bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 4 MiB at 0x47c00000 [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 15 pages/cpu s30912 r8192 d22336 u61440 [ 0.000000] pcpu-alloc: s30912 r8192 d22336 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 rootdelay=2 loglevel=8 root=/dev/mmcblk0p5 init=/sbin/init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:dsp0@mmcblk0p6:private@mmcblk0p7:UDISK@mmcblk0p8 cma=4M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun8iw20p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.05(11/02/2023-16:17:13) mbr_offset=1032192 disp_reserve=1536000,0x43f06000 androidboot.dramsize=128 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 104900K/131072K available (7168K kernel code, 406K rwdata, 2356K rodata, 1024K init, 171K bss, 22076K reserved, 4096K cma-reserved) [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x254/0x3d0 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.008009] Switching to timer-based delay loop, resolution 41ns [ 0.014183] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.023931] Console: colour dummy device 80x30 [ 0.028401] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.038753] pid_max: default: 32768 minimum: 301 [ 0.043436] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.050761] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.059084] CPU: Testing write buffer coherency: ok [ 0.064300] /cpus/cpu@0 missing clock-frequency property [ 0.069619] /cpus/cpu@1 missing clock-frequency property [ 0.074989] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.081332] Setting up static identity map for 0x40100000 - 0x40100060 [ 0.088036] rcu: Hierarchical SRCU implementation. [ 0.093186] BOOTEVENT: 93.176499: ON [ 0.097569] smp: Bringing up secondary CPUs ... [ 0.103392] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.103546] smp: Brought up 1 node, 2 CPUs [ 0.113354] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.119550] CPU: All CPU(s) started in SVC mode. [ 0.124764] devtmpfs: initialized [ 0.217196] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.227240] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.237123] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.246088] pinctrl core: initialized pinctrl subsystem [ 0.257540] NET: Registered protocol family 16 [ 0.265919] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.553344] rtc_ccu: sunxi ccu init OK [ 0.592855] ccu: sunxi ccu init OK [ 0.600033] r_ccu: sunxi ccu init OK [ 1.001237] iommu: Default domain type: Translated [ 1.006325] sunxi iommu: irq = 24 [ 1.030361] SCSI subsystem initialized [ 1.042196] usbcore: registered new interface driver usbfs [ 1.047896] usbcore: registered new interface driver hub [ 1.053343] usbcore: registered new device driver usb [ 1.062881] mc: Linux media interface: v0.10 [ 1.067975] videodev: Linux video capture interface: v2.00 [ 1.089001] Advanced Linux Sound Architecture Driver Initialized. [ 1.108860] Bluetooth: Core ver 2.22 [ 1.112560] NET: Registered protocol family 31 [ 1.117018] Bluetooth: HCI device and connection manager initialized [ 1.123496] Bluetooth: HCI socket layer initialized [ 1.128400] Bluetooth: L2CAP socket layer initialized [ 1.133499] Bluetooth: SCO socket layer initialized [ 1.139322] pwm module init! [ 1.148384] g2d 5410000.g2d: Adding to iommu group 0 [ 1.158870] G2D: rcq version initialized.major:251 [ 1.170738] clocksource: Switched to clocksource arch_sys_counter [ 1.338608] sun8iw20-pinctrl pio: initialized sunXi PIO driver [ 1.672247] thermal_sys: Registered thermal governor 'step_wise' [ 1.672253] thermal_sys: Registered thermal governor 'user_space' [ 1.695037] NET: Registered protocol family 2 [ 1.709148] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.717579] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 1.725329] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 1.732420] TCP: Hash tables configured (established 1024 bind 1024) [ 1.738880] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.745459] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.752647] NET: Registered protocol family 1 [ 1.774557] sun8iw20-pinctrl pio: pio supply vcc-pc not found, using dummy regulator [ 1.783095] spi spi0: spi0 supply spi not found, using dummy regulator [ 1.789972] sunxi_spi_resource_get()2116 - [spi0] SPI MASTER MODE [ 1.801647] sunxi_spi_resource_get()2154 - Failed to get sample mode [ 1.808026] sunxi_spi_resource_get()2159 - Failed to get sample delay [ 1.814510] sunxi_spi_resource_get()2163 - sample_mode:-1431633921 sample_delay:-1431633921 [ 1.822952] sunxi_spi_clk_init()2205 - [spi0] mclk 100000000 [ 1.835859] sunxi_spi_probe()2623 - [spi0]: driver probe succeed, base c881f000, irq 39 [ 1.870789] Initialise system trusted keyrings [ 1.877423] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 1.890123] fuse: init (API version 7.31) [ 1.929349] NET: Registered protocol family 38 [ 1.933863] Key type asymmetric registered [ 1.937983] Asymmetric key parser 'x509' registered [ 1.943011] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.950409] io scheduler mq-deadline registered [ 1.954966] io scheduler kyber registered [ 1.959070] atomic64_test: passed [ 1.975260] [DISP]disp_module_init [ 1.979405] disp 5000000.disp: Adding to iommu group 0 [ 1.993670] [DISP] parser_disp_init_para,line:1430: [ 1.993675] of_property_read fb0_width fail [ 2.002782] [DISP] disp_init,line:2386: [ 2.002787] smooth display screen:0 type:1 mode:4 [ 2.032723] display_fb_request,fb_id:0 [ 2.041840] Freeing logo buffer memory: 1500K [ 2.052537] disp_al_manager_apply ouput_type:1 [ 2.057264] sunxi_pwm_enable_dual: can't parse pwm device [ 2.065078] [DISP]disp_module_init finish [ 2.076224] sunxi_sid_init()551 - insmod ok [ 2.081018] pwm-regulator: supplied by regulator-dummy [ 2.113647] sun8iw20-pinctrl pio: pio supply vcc-pe not found, using dummy regulator [ 2.121892] uart uart0: uart0 supply uart not found, using dummy regulator [ 2.139741] uart0: ttyS0 at MMIO 0x2500000 (irq = 34, base_baud = 1500000) is a SUNXI [ 2.147633] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n [ 2.155649] printk: console [ttyS0] enabled [ 2.155649] printk: console [ttyS0] enabled [ 2.164533] printk: bootconsole [earlycon0] disabled [ 2.164533] printk: bootconsole [earlycon0] disabled [ 2.186007] misc dump reg init [ 2.217856] sun8iw20-pinctrl pio: pio supply vcc-pg not found, using dummy regulator [ 2.226975] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9 [ 2.234262] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed [ 2.241606] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed [ 2.249002] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1) [ 2.255550] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power. [ 2.262491] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1) [ 2.270237] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1 [ 2.278087] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1 [ 2.286196] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled [ 2.296788] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power. [ 2.304142] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1) [ 2.313348] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=210 assert=0 [ 2.336123] [ADDR_MGT] addr_mgt_probe: module version: v1.0.11 [ 2.343489] [ADDR_MGT] addr_mgt_probe: success. [ 2.373768] libphy: Fixed MDIO Bus: probed [ 2.381798] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.389126] sunxi-ehci: EHCI SUNXI driver [ 2.396169] get ehci1-controller wakeup-source is fail. [ 2.405974] sunxi ehci1-controller don't init wakeup source [ 2.412257] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xc0c86cd8, 0x:c8835000, irq_no:3a [ 2.424265] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply drvvbus not found, using dummy regulator [ 2.438945] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator [ 2.451168] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller [ 2.458438] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1 [ 2.471454] sunxi-ehci 4200000.ehci1-controller: irq 58, io mem 0x04200000 [ 2.500773] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00 [ 2.518585] hub 1-0:1.0: USB hub found [ 2.522901] hub 1-0:1.0: 1 port detected [ 2.547997] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.554959] sunxi-ohci: OHCI SUNXI driver [ 2.559978] get ohci1-controller wakeup-source is fail. [ 2.565978] sunxi ohci1-controller don't init wakeup source [ 2.572262] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xc0c86f68 [ 2.581924] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply drvvbus not found, using dummy regulator [ 2.601216] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator [ 2.613463] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller [ 2.623715] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2 [ 2.633783] sunxi-ohci 4200400.ohci1-controller: irq 59, io mem 0x04200400 [ 2.724846] hub 2-0:1.0: USB hub found [ 2.729110] hub 2-0:1.0: 1 port detected [ 2.752872] usbcore: registered new interface driver uas [ 2.758992] usbcore: registered new interface driver usb-storage [ 2.765863] usbcore: registered new interface driver ums-alauda [ 2.772580] usbcore: registered new interface driver ums-cypress [ 2.779399] usbcore: registered new interface driver ums-datafab [ 2.789203] usbcore: registered new interface driver ums_eneub6250 [ 2.796287] usbcore: registered new interface driver ums-freecom [ 2.803099] usbcore: registered new interface driver ums-isd200 [ 2.809815] usbcore: registered new interface driver ums-jumpshot [ 2.816781] usbcore: registered new interface driver ums-karma [ 2.823395] usbcore: registered new interface driver ums-onetouch [ 2.839265] usbcore: registered new interface driver ums-realtek [ 2.846336] usbcore: registered new interface driver ums-sddr09 [ 2.853064] usbcore: registered new interface driver ums-sddr55 [ 2.859815] usbcore: registered new interface driver ums-usbat [ 2.876235] sunxi_gpadc_init,2151, success [ 2.881196] sunxi_gpadc_setup: get channel scan data failed [ 2.893955] input: sunxi-gpadc0 as /devices/virtual/input/input0 [ 2.917372] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 2.928106] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 2.954834] sunxi-rtc 7090000.rtc: registered as rtc0 [ 2.960544] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 2.971171] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T01:21:22 UTC (4882) [ 2.980363] sunxi-rtc 7090000.rtc: sunxi rtc probed [ 2.986366] i2c /dev entries driver [ 2.990495] IR NEC protocol handler initialized [ 2.995599] IR RC5(x/sz) protocol handler initialized [ 3.004976] [VIN_WARN]sensor_helper_probe: cannot get sensor0_cameravdd supply, setting it to NULL! [ 3.015164] [VIN_WARN]sensor_helper_probe: cannot get sensor0_iovdd supply, setting it to NULL! [ 3.024908] [VIN_WARN]sensor_helper_probe: cannot get sensor0_avdd supply, setting it to NULL! [ 3.034565] [VIN_WARN]sensor_helper_probe: cannot get sensor0_dvdd supply, setting it to NULL! [ 3.044429] [VIN_WARN]sensor_helper_probe: cannot get sensor1_cameravdd supply, setting it to NULL! [ 3.054572] [VIN_WARN]sensor_helper_probe: cannot get sensor1_iovdd supply, setting it to NULL! [ 3.064324] [VIN_WARN]sensor_helper_probe: cannot get sensor1_avdd supply, setting it to NULL! [ 3.073971] [VIN_WARN]sensor_helper_probe: cannot get sensor1_dvdd supply, setting it to NULL! [ 3.090140] usbcore: registered new interface driver uvcvideo [ 3.096628] USB Video Class driver (1.1.1) [ 3.101238] gspca_main: v2.14.0 registered [ 3.105810] sunxi cedar version 1.1 [ 3.123521] sunxi-wdt 20500a0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 3.132789] Bluetooth: HCI UART driver ver 2.3 [ 3.137762] Bluetooth: HCI UART protocol H4 registered [ 3.143866] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10 [ 3.187953] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.22 2021-12-20 15:40) [ 3.197944] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8 [ 3.204151] sunxi-mmc 4020000.sdmmc: No vmmc regulator found [ 3.210513] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found [ 3.217008] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found [ 3.223456] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found [ 3.229987] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found [ 3.236530] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found [ 3.243058] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found [ 3.250118] sunxi-mmc 4020000.sdmmc: Got CD GPIO [ 3.255774] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.266989] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator [ 3.287123] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.312316] sunxi-mmc 4020000.sdmmc: detmode:gpio irq [ 3.318001] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.327674] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.22 2021-12-20 15:40) [ 3.339556] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8 [ 3.340609] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.345782] sunxi-mmc 4021000.sdmmc: No vmmc regulator found [ 3.363726] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found [ 3.370167] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found [ 3.376616] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found [ 3.376630] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.383161] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found [ 3.383168] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found [ 3.402564] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.407817] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found [ 3.425958] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed [ 3.438681] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.449870] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 3.470067] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.492486] mmc0: host does not support reading read-only switch, assuming write-enable [ 3.501470] sunxi-mmc 4021000.sdmmc: detmode:manually by software [ 3.508300] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 3.509129] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 3.520043] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 3.530179] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 3.545181] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 3.545206] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.556963] mmc0: new high speed SDHC card at address aaaa [ 3.569265] usbcore: registered new interface driver usbhid [ 3.590231] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.591645] mmcblk0: mmc0:aaaa SL32G 29.7 GiB [ 3.602078] usbhid: USB HID core driver [ 3.618801] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.628904] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.636631] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 [ 3.640156] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.651546] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.658328] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 3.709386] [AUDIOCODEC][sunxi_codec_parse_params][2412]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1 [ 3.709386] [ 3.731398] [AUDIOCODEC][sunxi_codec_parse_params][2448]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0 [ 3.742961] [AUDIOCODEC][sunxi_internal_codec_probe][2609]:codec probe finished [ 3.768230] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present! [ 3.778043] [SNDCODEC][sunxi_card_init][583]:card init finished [ 3.788445] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok [ 3.832627] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input1 [ 3.861177] [SNDCODEC][sunxi_card_dev_probe][836]:register card finished [ 3.869318] NET: Registered protocol family 10 [ 3.881206] [SNDCODEC][sunxi_hs_init_work][259]:resume-->report switch [ 3.895893] Segment Routing with IPv6 [ 3.903378] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.945407] NET: Registered protocol family 17 [ 3.950411] NET: Registered protocol family 15 [ 3.955572] Bluetooth: RFCOMM TTY layer initialized [ 3.961113] Bluetooth: RFCOMM socket layer initialized [ 3.966903] Bluetooth: RFCOMM ver 1.11 [ 3.971864] Registering SWP/SWPB emulation handler [ 3.980612] Loading compiled-in X.509 certificates [ 4.322350] sunxi-i2c sunxi-i2c2: sunxi-i2c2 supply twi not found, using dummy regulator [ 4.352716] sunxi-i2c sunxi-i2c2: probe success [ 4.367074] sun8iw20-pinctrl pio: pio supply vcc-pb not found, using dummy regulator [ 4.427817] platform 2000c13.pwm3: pinctrl_get failed [ 4.436940] platform 2000c13.pwm3: pinctrl_get failed [ 4.442638] cpu cpu0: _set_opp_voltage: failed to set voltage (1000000 1000000 1000000 mV): -19 [ 4.455781] platform 2000c13.pwm3: pinctrl_get failed [ 4.464877] platform 2000c13.pwm3: pinctrl_get failed [ 4.470567] cpu cpu0: _set_opp_voltage: failed to set voltage (900000 900000 900000 mV): -19 [ 4.480035] cpufreq: __target_index: Failed to change cpu frequency: -19 [ 4.495961] get ehci0-controller wakeup-source is fail. [ 4.508653] sunxi ehci0-controller don't init wakeup source [ 4.514944] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xc0c867b8, 0x:c88da000, irq_no:38 [ 4.526953] [sunxi-ehci0]: Not init ehci0 [ 4.531931] get ohci0-controller wakeup-source is fail. [ 4.537922] sunxi ohci0-controller don't init wakeup source [ 4.544180] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xc0c86a48 [ 4.553851] [sunxi-ohci0]: Not init ohci0 [ 4.562714] platform 2000c13.pwm3: pinctrl_get failed [ 4.573870] platform 2000c13.pwm3: pinctrl_get failed [ 4.574485] get usb_detect_mode is fail, -22 [ 4.579532] cpu cpu0: _set_opp_voltage: failed to set voltage (1000000 1000000 1000000 mV): -19 [ 4.584623] get det_vbus is fail, -84 [ 4.594275] platform 2000c13.pwm3: pinctrl_get failed [ 4.598151] get id is fail, -84 [ 4.603914] platform 2000c13.pwm3: pinctrl_get failed [ 4.616201] cpu cpu0: _set_opp_voltage: failed to set voltage (900000 900000 900000 mV): -19 [ 4.616463] get ctp_power is fail, -22 [ 4.625816] cpufreq: __target_index: Failed to change cpu frequency: -19 [ 4.630061] get ctp_power_ldo_vol is fail, -22 [ 4.642484] sunxi_ctp_startup: ctp_power_io is invalid. [ 4.648372] get ctp_gesture_wakeup fail, no gesture wakeup [ 4.654534] gt9xxnew_ts 2-0014: 2-0014 supply ctp not found, using dummy regulator [ 4.820807] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 4.828910] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 4.836553] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 4.844645] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 4.852284] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 4.860371] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 4.868012] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 4.876103] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 4.883740] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 4.891830] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 4.899412] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -22! Process reset. [ 5.060742] <<-GTP-ERROR->> GTP i2c test failed time 1. [ 5.090786] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.098878] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.106523] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.114619] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.122262] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.130354] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.138023] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.146120] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.153764] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.161858] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.169444] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -22! Process reset. [ 5.330743] <<-GTP-ERROR->> GTP i2c test failed time 2. [ 5.360783] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.368876] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.376272] random: fast init done [ 5.380284] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.388379] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.396018] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.404109] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.411749] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.419840] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.427481] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.435570] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.443170] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -22! Process reset. [ 5.610747] <<-GTP-ERROR->> GTP i2c test failed time 3. [ 5.640786] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.648880] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.656524] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.664618] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.672262] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.680353] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.687995] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.690741] [ 5.690741] insmod_device_driver [ 5.690741] [ 5.696107] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.703274] sunxi_usb_udc 4100000.udc-controller: 4100000.udc-controller supply udc not found, using dummy regulator [ 5.710630] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.722700] device_chose finished 142! [ 5.730578] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.742222] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -22! Process reset. [ 5.910749] <<-GTP-ERROR->> GTP i2c test failed time 4. [ 5.940793] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.948900] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.956548] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.964658] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.972305] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.980401] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 5.988055] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 5.996149] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 6.003798] sunxi-i2c sunxi-i2c2: SLA+W has been transmitted; ACK not received [ 6.011899] sunxi-i2c sunxi-i2c2: engine-mode: xfer failed(dev addr:0x14) [ 6.019495] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -22! Process reset. [ 6.180745] <<-GTP-ERROR->> GTP i2c test failed time 5. [ 6.210743] I2C communication ERROR! [ 6.210768] regulator-dummy: Underflow of regulator enable count [ 6.221735] gt9xxnew_ts: probe of 2-0014 failed with error -1 [ 6.238631] sun8iw20-pinctrl pio: pin PE2 already requested by 2500000.uart; cannot claim for 5801000.csi [ 6.249491] sun8iw20-pinctrl pio: pin-130 (5801000.csi) status -22 [ 6.256434] sun8iw20-pinctrl pio: could not request pin 130 (PE2) from group PE2 on device pio [ 6.266274] vin_csi 5801000.csi: Error applying setting, reverse things back [ 6.274294] vin_csi: probe of 5801000.csi failed with error -22 [ 6.350047] sunxi-vin-core 5809000.vinc: Adding to iommu group 0 [ 6.365345] sunxi-vin-core 5809200.vinc: Adding to iommu group 0 [ 6.384970] [VIN_WARN]get csi isp clk fail [ 6.389580] [VIN_WARN]get csi isp src clk fail [ 6.394617] [VIN_WARN]get csi mipi clk fail [ 6.399296] [VIN_WARN]get csi mipi src clk fail [ 6.404533] [VIN_WARN]get csi isp clk fail [ 6.411723] [VIN_WARN]Get isp reset control fail [ 6.421255] [VIN_ERR]registering ov5640, No such device! [ 6.427200] [VIN_ERR]ov5647 request i2c3 adapter failed! [ 6.433260] ------------[ cut here ]------------ [ 6.438426] kernel BUG at /home/tronlong/T113/T113-i_v1.0/kernel/linux-5.4/drivers/media/mc/mc-entity.c:666! [ 6.449398] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM [ 6.455912] Modules linked in: [ 6.459325] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.61 #3 [ 6.465936] Hardware name: Generic DT based system [ 6.471292] PC is at media_create_pad_link+0x30/0x130 [ 6.476937] LR is at vin_probe+0xab4/0xe24 [ 6.481508] pc : [<c04e5924>] lr : [<c051bec0>] psr: 60000113 [ 6.488509] sp : c7419d88 ip : 00000001 fp : 00000000 [ 6.494340] r10: 00000000 r9 : c09d7723 r8 : c084a0d8 [ 6.500176] r7 : 00000002 r6 : c70d758c r5 : 00000000 r4 : c3cba5c0 [ 6.507461] r3 : 00000000 r2 : c3cf0000 r1 : 00000001 r0 : c70d758c [ 6.514754] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none [ 6.522722] Control: 10c5387d Table: 4000406a DAC: 00000051 [ 6.529142] Process swapper/0 (pid: 1, stack limit = 0x(ptrval)) [ 6.535847] Stack: (0xc7419d88 to 0xc741a000) [ 6.540715] 9d80: 00000000 c3cba5c0 00000000 c70d758c 00000002 c084a0d8 [ 6.549852] 9da0: c09d7723 c09d712c c3cbad4c c051bec0 00000000 00000001 c3cbae20 c75591d0 [ 6.558994] 9dc0: c3cba5c0 c3cbac70 c3cba5fc c3cba604 00000005 1406f400 5f697363 6b6c636d [ 6.568129] 9de0: 6c705f30 c75b006c c09c5a66 8714496c 00000001 00000000 c75591d0 c0c51428 [ 6.577270] 9e00: 00000000 7c53a23c 00000001 fffffdfb c0c84e8c c0413090 c75591d0 00000000 [ 6.586405] 9e20: c0c51428 c041144c c75cc3e4 00000004 60000113 00000010 c75592a4 c75591d0 [ 6.595546] 9e40: c0c51428 c0c51428 c0411b14 733bcd6f 00000001 c0c66000 00000000 c0411928 [ 6.604681] 9e60: c0c51428 c75591d0 8714496c 00000000 c75591d0 c0c51428 c0411b14 733bcd6f [ 6.613823] 9e80: 00000001 c0411afc 00000000 c75591d0 c0c51428 c0411bc0 c75591d0 c7418000 [ 6.622959] 9ea0: c0c51428 c040f984 c750d5bc c750d5a8 c75b0cf4 8714496c c750d5bc c0c51428 [ 6.632101] 9ec0: 00000000 c3cc2040 c0c38ab0 c0410898 c09d7897 00000001 00000000 c0c51428 [ 6.641234] 9ee0: c0c66000 c0b1b328 00000000 c04123a8 00000000 c0c66000 c0b1b328 c0b1b394 [ 6.650376] 9f00: c7418000 c0102f6c c0a4c3bc 00000000 00000000 c0133b00 00000000 c0b00514 [ 6.659512] 9f20: c0a4b458 000000c6 00000007 00000007 00000000 c0a4c3d0 000000c5 c0a4c3d0 [ 6.668654] 9f40: cccccccd c7bff9e7 c7bff9fc 8714496c 00000000 8714496c 00000008 c0c66000 [ 6.677790] 9f60: c0b2d038 000000c6 c0c66000 c0b3acc0 c0b2d03c c0b00e04 00000007 00000007 [ 6.686932] 9f80: 00000000 c0b00514 00000000 c072ed38 00000000 00000000 00000000 00000000 [ 6.696066] 9fa0: 00000000 c072ed40 00000000 c01010e8 00000000 00000000 00000000 00000000 [ 6.705207] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 6.714341] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [ 6.723494] [<c04e5924>] (media_create_pad_link) from [<c051bec0>] (vin_probe+0xab4/0xe24) [ 6.732732] [<c051bec0>] (vin_probe) from [<c0413090>] (platform_drv_probe+0x48/0x98) [ 6.741489] [<c0413090>] (platform_drv_probe) from [<c041144c>] (really_probe+0x1a8/0x418) [ 6.750724] [<c041144c>] (really_probe) from [<c0411928>] (driver_probe_device+0x10c/0x154) [ 6.760061] [<c0411928>] (driver_probe_device) from [<c0411afc>] (device_driver_attach+0x44/0x5c) [ 6.769976] [<c0411afc>] (device_driver_attach) from [<c0411bc0>] (__driver_attach+0xac/0xb8) [ 6.779505] [<c0411bc0>] (__driver_attach) from [<c040f984>] (bus_for_each_dev+0x6c/0xa4) [ 6.788640] [<c040f984>] (bus_for_each_dev) from [<c0410898>] (bus_add_driver+0xd8/0x1b4) [ 6.797784] [<c0410898>] (bus_add_driver) from [<c04123a8>] (driver_register+0xb0/0xf8) [ 6.806727] [<c04123a8>] (driver_register) from [<c0b1b394>] (vin_init+0x6c/0xb8) [ 6.815096] [<c0b1b394>] (vin_init) from [<c0102f6c>] (do_one_initcall+0x7c/0x1b4) [ 6.823555] [<c0102f6c>] (do_one_initcall) from [<c0b00e04>] (kernel_init_freeable+0x108/0x1cc) [ 6.833284] [<c0b00e04>] (kernel_init_freeable) from [<c072ed40>] (kernel_init+0x8/0x118) [ 6.842422] [<c072ed40>] (kernel_init) from [<c01010e8>] (ret_from_fork+0x14/0x2c) [ 6.850880] Exception stack(0xc7419fb0 to 0xc7419ff8) [ 6.856519] 9fa0: 00000000 00000000 00000000 00000000 [ 6.865660] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 6.874793] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 6.882188] Code: ea000008 e1d0c2b0 e15c0001 8a000001 (e7f001f2) [ 6.888993] ---[ end trace 3b8545bbcdec8364 ]--- [ 6.894154] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 6.902712] CPU1: stopping [ 6.905739] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G D 5.4.61 #3 [ 6.913909] Hardware name: Generic DT based system [ 6.919272] [<c010e390>] (unwind_backtrace) from [<c010a934>] (show_stack+0x10/0x14) [ 6.927936] [<c010a934>] (show_stack) from [<c071a558>] (dump_stack+0x7c/0x98) [ 6.936013] [<c071a558>] (dump_stack) from [<c010c730>] (handle_IPI+0xc0/0x168) [ 6.944193] [<c010c730>] (handle_IPI) from [<c036da34>] (gic_handle_irq+0x70/0x78) [ 6.952656] [<c036da34>] (gic_handle_irq) from [<c01021cc>] (__irq_svc+0x6c/0xa8) [ 6.961021] Exception stack(0xc7441f80 to 0xc7441fc8) [ 6.966668] 1f80: 00000f98 c7aca534 00000000 c0114dc0 00000002 c7440000 c0c03de4 c0c03e20 [ 6.975815] 1fa0: 4000406a 410fc075 00000000 00000000 c0c708b0 c7441fd0 c0108020 c0108024 [ 6.984952] 1fc0: 60000113 ffffffff [ 6.988856] [<c01021cc>] (__irq_svc) from [<c0108024>] (arch_cpu_idle+0x2c/0x38) [ 6.997128] [<c0108024>] (arch_cpu_idle) from [<c013e5d0>] (do_idle+0xb8/0x120) [ 7.005305] [<c013e5d0>] (do_idle) from [<c013e8cc>] (cpu_startup_entry+0x18/0x1c) [ 7.013767] [<c013e8cc>] (cpu_startup_entry) from [<40102c0c>] (0x40102c0c) [ 7.021556] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b ]--- -
@xsyr1024 在kernel里关闭VIN驱动
-
@awwwwa 谢谢大佬，我用最小的内核配置编译，现在能进系统了。
tina的编译脚步真让人抓狂，看了很久都不知道linux 内核的配置从哪些文件合并的。 -
@xsyr1024 tina其实就是openwrt，在openwrt中的KERNEL_开头的选项就是会影响到内核配置
-
@awwwwa 你好，请问打开了UART0的DMA之后卡在这个地方是为啥呀
Copyright © 2024 深圳全志在线有限公司 粤ICP备2021084185号 粤公网安备44030502007680号